include/asm-x86_64/serial.h

   1 /*
   2  * include/asm-x86_64/serial.h
   3  */
   4
   5 #include <linux/config.h>
   6
   7 /*
   8  * This assumes you have a 1.8432 MHz clock for your UART.
   9  *
  10  * It'd be nice if someone built a serial card with a 24.576 MHz
  11  * clock, since the 16550A is capable of handling a top speed of 1.5
  12  * megabits/second; but this requires the faster clock.
  13  */
  14 #define BASE_BAUD ( 1843200 / 16 )
  15
  16 /* Standard COM flags (except for COM4, because of the 8514 problem) */
  17 #ifdef CONFIG_SERIAL_DETECT_IRQ
  18 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
  19 #define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
  20 #else
  21 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
  22 #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
  23 #endif
  24
  25 #ifdef CONFIG_SERIAL_MANY_PORTS
  26 #define FOURPORT_FLAGS ASYNC_FOURPORT
  27 #define ACCENT_FLAGS 0
  28 #define BOCA_FLAGS 0
  29 #define HUB6_FLAGS 0
  30 #endif
  31
  32 #define MCA_COM_FLAGS   (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA)
  33
  34 /*
  35  * The following define the access methods for the HUB6 card. All
  36  * access is through two ports for all 24 possible chips. The card is
  37  * selected through the high 2 bits, the port on that card with the
  38  * "middle" 3 bits, and the register on that port with the bottom
  39  * 3 bits.
  40  *
  41  * While the access port and interrupt is configurable, the default
  42  * port locations are 0x302 for the port control register, and 0x303
  43  * for the data read/write register. Normally, the interrupt is at irq3
  44  * but can be anything from 3 to 7 inclusive. Note that using 3 will
  45  * require disabling com2.
  46  */
  47
  48 #define C_P(card,port) (((card)<<6|(port)<<3) + 1)
  49
  50 #define STD_SERIAL_PORT_DEFNS                   \
  51         /* UART CLK   PORT IRQ     FLAGS        */                      \
  52         { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS },      /* ttyS0 */     \
  53         { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS },      /* ttyS1 */     \
  54         { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS },      /* ttyS2 */     \
  55         { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS },     /* ttyS3 */
  56
  57
  58 #ifdef CONFIG_SERIAL_MANY_PORTS
  59 #define EXTRA_SERIAL_PORT_DEFNS                 \
  60         { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS },     /* ttyS4 */     \
  61         { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS },     /* ttyS5 */     \
  62         { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS },     /* ttyS6 */     \
  63         { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS },     /* ttyS7 */     \
  64         { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS },     /* ttyS8 */     \
  65         { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS },     /* ttyS9 */     \
  66         { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS },     /* ttyS10 */    \
  67         { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS },     /* ttyS11 */    \
  68         { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS },       /* ttyS12 */    \
  69         { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS },       /* ttyS13 */    \
  70         { 0, BASE_BAUD, 0x000, 0, 0 },  /* ttyS14 (spare) */            \
  71         { 0, BASE_BAUD, 0x000, 0, 0 },  /* ttyS15 (spare) */            \
  72         { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS },        /* ttyS16 */    \
  73         { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS },        /* ttyS17 */    \
  74         { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS },        /* ttyS18 */    \
  75         { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS },        /* ttyS19 */    \
  76         { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS },        /* ttyS20 */    \
  77         { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS },        /* ttyS21 */    \
  78         { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS },        /* ttyS22 */    \
  79         { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS },        /* ttyS23 */    \
  80         { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS },        /* ttyS24 */    \
  81         { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS },        /* ttyS25 */    \
  82         { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS },        /* ttyS26 */    \
  83         { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS },        /* ttyS27 */    \
  84         { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS },        /* ttyS28 */    \
  85         { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS },        /* ttyS29 */    \
  86         { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS },        /* ttyS30 */    \
  87         { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS },        /* ttyS31 */
  88 #else
  89 #define EXTRA_SERIAL_PORT_DEFNS
  90 #endif
  91
  92 /* You can have up to four HUB6's in the system, but I've only
  93  * included two cards here for a total of twelve ports.
  94  */
  95 #if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
  96 #define HUB6_SERIAL_PORT_DFNS           \
  97         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) },  /* ttyS32 */ \
  98         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) },  /* ttyS33 */ \
  99         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) },  /* ttyS34 */ \
 100         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) },  /* ttyS35 */ \
 101         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) },  /* ttyS36 */ \
 102         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) },  /* ttyS37 */ \
 103         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) },  /* ttyS38 */ \
 104         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) },  /* ttyS39 */ \
 105         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) },  /* ttyS40 */ \
 106         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) },  /* ttyS41 */ \
 107         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) },  /* ttyS42 */ \
 108         { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) },  /* ttyS43 */
 109 #else
 110 #define HUB6_SERIAL_PORT_DFNS
 111 #endif
 112
 113 #ifdef CONFIG_MCA
 114 #define MCA_SERIAL_PORT_DFNS                    \
 115         { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS },     \
 116         { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS },     \
 117         { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS },     \
 118         { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS },     \
 119         { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS },     \
 120         { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS },
 121 #else
 122 #define MCA_SERIAL_PORT_DFNS
 123 #endif
 124
 125 #define SERIAL_PORT_DFNS                \
 126         STD_SERIAL_PORT_DEFNS           \
 127         EXTRA_SERIAL_PORT_DEFNS         \
 128         HUB6_SERIAL_PORT_DFNS           \
 129         MCA_SERIAL_PORT_DFNS
 130