arch/arm/mach-omap2/pm34xx.c

   1 /*
   2  * OMAP3 Power Management Routines
   3  *
   4  * Copyright (C) 2006-2008 Nokia Corporation
   5  * Tony Lindgren <tony@atomide.com>
   6  * Jouni Hogander
   7  *
   8  * Copyright (C) 2007 Texas Instruments, Inc.
   9  * Rajendra Nayak <rnayak@ti.com>
  10  *
  11  * Copyright (C) 2005 Texas Instruments, Inc.
  12  * Richard Woodruff <r-woodruff2@ti.com>
  13  *
  14  * Based on pm.c for omap1
  15  *
  16  * This program is free software; you can redistribute it and/or modify
  17  * it under the terms of the GNU General Public License version 2 as
  18  * published by the Free Software Foundation.
  19  */
  20
  21 #include <linux/pm.h>
  22 #include <linux/suspend.h>
  23 #include <linux/interrupt.h>
  24 #include <linux/module.h>
  25 #include <linux/list.h>
  26 #include <linux/err.h>
  27 #include <linux/gpio.h>
  28 #include <linux/clk.h>
  29 #include <linux/delay.h>
  30 #include <linux/slab.h>
  31 #include <linux/omap-dma.h>
  32 #include <linux/platform_data/gpio-omap.h>
  33
  34 #include <trace/events/power.h>
  35
  36 #include <asm/fncpy.h>
  37 #include <asm/suspend.h>
  38 #include <asm/system_misc.h>
  39
  40 #include "clockdomain.h"
  41 #include "powerdomain.h"
  42 #include "soc.h"
  43 #include "common.h"
  44 #include "cm3xxx.h"
  45 #include "cm-regbits-34xx.h"
  46 #include "gpmc.h"
  47 #include "prm-regbits-34xx.h"
  48 #include "prm3xxx.h"
  49 #include "pm.h"
  50 #include "sdrc.h"
  51 #include "sram.h"
  52 #include "control.h"
  53
  54 /* pm34xx errata defined in pm.h */
  55 u16 pm34xx_errata;
  56
  57 struct power_state {
  58         struct powerdomain *pwrdm;
  59         u32 next_state;
  60 #ifdef CONFIG_SUSPEND
  61         u32 saved_state;
  62 #endif
  63         struct list_head node;
  64 };
  65
  66 static LIST_HEAD(pwrst_list);
  67
  68 static int (*_omap_save_secure_sram)(u32 *addr);
  69 void (*omap3_do_wfi_sram)(void);
  70
  71 static struct powerdomain *mpu_pwrdm, *neon_pwrdm;
  72 static struct powerdomain *core_pwrdm, *per_pwrdm;
  73
  74 static void omap3_core_save_context(void)
  75 {
  76         omap3_ctrl_save_padconf();
  77
  78         /*
  79          * Force write last pad into memory, as this can fail in some
  80          * cases according to errata 1.157, 1.185
  81          */
  82         omap_ctrl_writel(omap_ctrl_readl(OMAP343X_PADCONF_ETK_D14),
  83                 OMAP343X_CONTROL_MEM_WKUP + 0x2a0);
  84
  85         /* Save the Interrupt controller context */
  86         omap_intc_save_context();
  87         /* Save the GPMC context */
  88         omap3_gpmc_save_context();
  89         /* Save the system control module context, padconf already save above*/
  90         omap3_control_save_context();
  91         omap_dma_global_context_save();
  92 }
  93
  94 static void omap3_core_restore_context(void)
  95 {
  96         /* Restore the control module context, padconf restored by h/w */
  97         omap3_control_restore_context();
  98         /* Restore the GPMC context */
  99         omap3_gpmc_restore_context();
 100         /* Restore the interrupt controller context */
 101         omap_intc_restore_context();
 102         omap_dma_global_context_restore();
 103 }
 104
 105 /*
 106  * FIXME: This function should be called before entering off-mode after
 107  * OMAP3 secure services have been accessed. Currently it is only called
 108  * once during boot sequence, but this works as we are not using secure
 109  * services.
 110  */
 111 static void omap3_save_secure_ram_context(void)
 112 {
 113         u32 ret;
 114         int mpu_next_state = pwrdm_read_next_pwrst(mpu_pwrdm);
 115
 116         if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
 117                 /*
 118                  * MPU next state must be set to POWER_ON temporarily,
 119                  * otherwise the WFI executed inside the ROM code
 120                  * will hang the system.
 121                  */
 122                 pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
 123                 ret = _omap_save_secure_sram((u32 *)(unsigned long)
 124                                 __pa(omap3_secure_ram_storage));
 125                 pwrdm_set_next_pwrst(mpu_pwrdm, mpu_next_state);
 126                 /* Following is for error tracking, it should not happen */
 127                 if (ret) {
 128                         pr_err("save_secure_sram() returns %08x\n", ret);
 129                         while (1)
 130                                 ;
 131                 }
 132         }
 133 }
 134
 135 /*
 136  * PRCM Interrupt Handler Helper Function
 137  *
 138  * The purpose of this function is to clear any wake-up events latched
 139  * in the PRCM PM_WKST_x registers. It is possible that a wake-up event
 140  * may occur whilst attempting to clear a PM_WKST_x register and thus
 141  * set another bit in this register. A while loop is used to ensure
 142  * that any peripheral wake-up events occurring while attempting to
 143  * clear the PM_WKST_x are detected and cleared.
 144  */
 145 static int prcm_clear_mod_irqs(s16 module, u8 regs, u32 ignore_bits)
 146 {
 147         u32 wkst, fclk, iclk, clken;
 148         u16 wkst_off = (regs == 3) ? OMAP3430ES2_PM_WKST3 : PM_WKST1;
 149         u16 fclk_off = (regs == 3) ? OMAP3430ES2_CM_FCLKEN3 : CM_FCLKEN1;
 150         u16 iclk_off = (regs == 3) ? CM_ICLKEN3 : CM_ICLKEN1;
 151         u16 grpsel_off = (regs == 3) ?
 152                 OMAP3430ES2_PM_MPUGRPSEL3 : OMAP3430_PM_MPUGRPSEL;
 153         int c = 0;
 154
 155         wkst = omap2_prm_read_mod_reg(module, wkst_off);
 156         wkst &= omap2_prm_read_mod_reg(module, grpsel_off);
 157         wkst &= ~ignore_bits;
 158         if (wkst) {
 159                 iclk = omap2_cm_read_mod_reg(module, iclk_off);
 160                 fclk = omap2_cm_read_mod_reg(module, fclk_off);
 161                 while (wkst) {
 162                         clken = wkst;
 163                         omap2_cm_set_mod_reg_bits(clken, module, iclk_off);
 164                         /*
 165                          * For USBHOST, we don't know whether HOST1 or
 166                          * HOST2 woke us up, so enable both f-clocks
 167                          */
 168                         if (module == OMAP3430ES2_USBHOST_MOD)
 169                                 clken |= 1 << OMAP3430ES2_EN_USBHOST2_SHIFT;
 170                         omap2_cm_set_mod_reg_bits(clken, module, fclk_off);
 171                         omap2_prm_write_mod_reg(wkst, module, wkst_off);
 172                         wkst = omap2_prm_read_mod_reg(module, wkst_off);
 173                         wkst &= ~ignore_bits;
 174                         c++;
 175                 }
 176                 omap2_cm_write_mod_reg(iclk, module, iclk_off);
 177                 omap2_cm_write_mod_reg(fclk, module, fclk_off);
 178         }
 179
 180         return c;
 181 }
 182
 183 static irqreturn_t _prcm_int_handle_io(int irq, void *unused)
 184 {
 185         int c;
 186
 187         c = prcm_clear_mod_irqs(WKUP_MOD, 1,
 188                 ~(OMAP3430_ST_IO_MASK | OMAP3430_ST_IO_CHAIN_MASK));
 189
 190         return c ? IRQ_HANDLED : IRQ_NONE;
 191 }
 192
 193 static irqreturn_t _prcm_int_handle_wakeup(int irq, void *unused)
 194 {
 195         int c;
 196
 197         /*
 198          * Clear all except ST_IO and ST_IO_CHAIN for wkup module,
 199          * these are handled in a separate handler to avoid acking
 200          * IO events before parsing in mux code
 201          */
 202         c = prcm_clear_mod_irqs(WKUP_MOD, 1,
 203                 OMAP3430_ST_IO_MASK | OMAP3430_ST_IO_CHAIN_MASK);
 204         c += prcm_clear_mod_irqs(CORE_MOD, 1, 0);
 205         c += prcm_clear_mod_irqs(OMAP3430_PER_MOD, 1, 0);
 206         if (omap_rev() > OMAP3430_REV_ES1_0) {
 207                 c += prcm_clear_mod_irqs(CORE_MOD, 3, 0);
 208                 c += prcm_clear_mod_irqs(OMAP3430ES2_USBHOST_MOD, 1, 0);
 209         }
 210
 211         return c ? IRQ_HANDLED : IRQ_NONE;
 212 }
 213
 214 static void omap34xx_save_context(u32 *save)
 215 {
 216         u32 val;
 217
 218         /* Read Auxiliary Control Register */
 219         asm("mrc p15, 0, %0, c1, c0, 1" : "=r" (val));
 220         *save++ = 1;
 221         *save++ = val;
 222
 223         /* Read L2 AUX ctrl register */
 224         asm("mrc p15, 1, %0, c9, c0, 2" : "=r" (val));
 225         *save++ = 1;
 226         *save++ = val;
 227 }
 228
 229 static int omap34xx_do_sram_idle(unsigned long save_state)
 230 {
 231         omap34xx_cpu_suspend(save_state);
 232         return 0;
 233 }
 234
 235 void omap_sram_idle(void)
 236 {
 237         /* Variable to tell what needs to be saved and restored
 238          * in omap_sram_idle*/
 239         /* save_state = 0 => Nothing to save and restored */
 240         /* save_state = 1 => Only L1 and logic lost */
 241         /* save_state = 2 => Only L2 lost */
 242         /* save_state = 3 => L1, L2 and logic lost */
 243         int save_state = 0;
 244         int mpu_next_state = PWRDM_POWER_ON;
 245         int per_next_state = PWRDM_POWER_ON;
 246         int core_next_state = PWRDM_POWER_ON;
 247         int per_going_off;
 248         int core_prev_state;
 249         u32 sdrc_pwr = 0;
 250
 251         mpu_next_state = pwrdm_read_next_pwrst(mpu_pwrdm);
 252         switch (mpu_next_state) {
 253         case PWRDM_POWER_ON:
 254         case PWRDM_POWER_RET:
 255                 /* No need to save context */
 256                 save_state = 0;
 257                 break;
 258         case PWRDM_POWER_OFF:
 259                 save_state = 3;
 260                 break;
 261         default:
 262                 /* Invalid state */
 263                 pr_err("Invalid mpu state in sram_idle\n");
 264                 return;
 265         }
 266
 267         /* NEON control */
 268         if (pwrdm_read_pwrst(neon_pwrdm) == PWRDM_POWER_ON)
 269                 pwrdm_set_next_pwrst(neon_pwrdm, mpu_next_state);
 270
 271         /* Enable IO-PAD and IO-CHAIN wakeups */
 272         per_next_state = pwrdm_read_next_pwrst(per_pwrdm);
 273         core_next_state = pwrdm_read_next_pwrst(core_pwrdm);
 274
 275         pwrdm_pre_transition(NULL);
 276
 277         /* PER */
 278         if (per_next_state < PWRDM_POWER_ON) {
 279                 per_going_off = (per_next_state == PWRDM_POWER_OFF) ? 1 : 0;
 280                 omap2_gpio_prepare_for_idle(per_going_off);
 281         }
 282
 283         /* CORE */
 284         if (core_next_state < PWRDM_POWER_ON) {
 285                 if (core_next_state == PWRDM_POWER_OFF) {
 286                         omap3_core_save_context();
 287                         omap3_cm_save_context();
 288                 }
 289         }
 290
 291         omap3_intc_prepare_idle();
 292
 293         /*
 294          * On EMU/HS devices ROM code restores a SRDC value
 295          * from scratchpad which has automatic self refresh on timeout
 296          * of AUTO_CNT = 1 enabled. This takes care of erratum ID i443.
 297          * Hence store/restore the SDRC_POWER register here.
 298          */
 299         if (cpu_is_omap3430() && omap_rev() >= OMAP3430_REV_ES3_0 &&
 300             (omap_type() == OMAP2_DEVICE_TYPE_EMU ||
 301              omap_type() == OMAP2_DEVICE_TYPE_SEC) &&
 302             core_next_state == PWRDM_POWER_OFF)
 303                 sdrc_pwr = sdrc_read_reg(SDRC_POWER);
 304
 305         /*
 306          * omap3_arm_context is the location where some ARM context
 307          * get saved. The rest is placed on the stack, and restored
 308          * from there before resuming.
 309          */
 310         if (save_state)
 311                 omap34xx_save_context(omap3_arm_context);
 312         if (save_state == 1 || save_state == 3)
 313                 cpu_suspend(save_state, omap34xx_do_sram_idle);
 314         else
 315                 omap34xx_do_sram_idle(save_state);
 316
 317         /* Restore normal SDRC POWER settings */
 318         if (cpu_is_omap3430() && omap_rev() >= OMAP3430_REV_ES3_0 &&
 319             (omap_type() == OMAP2_DEVICE_TYPE_EMU ||
 320              omap_type() == OMAP2_DEVICE_TYPE_SEC) &&
 321             core_next_state == PWRDM_POWER_OFF)
 322                 sdrc_write_reg(sdrc_pwr, SDRC_POWER);
 323
 324         /* CORE */
 325         if (core_next_state < PWRDM_POWER_ON) {
 326                 core_prev_state = pwrdm_read_prev_pwrst(core_pwrdm);
 327                 if (core_prev_state == PWRDM_POWER_OFF) {
 328                         omap3_core_restore_context();
 329                         omap3_cm_restore_context();
 330                         omap3_sram_restore_context();
 331                         omap2_sms_restore_context();
 332                 }
 333                 if (core_next_state == PWRDM_POWER_OFF)
 334                         omap2_prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
 335                                                OMAP3430_GR_MOD,
 336                                                OMAP3_PRM_VOLTCTRL_OFFSET);
 337         }
 338         omap3_intc_resume_idle();
 339
 340         pwrdm_post_transition(NULL);
 341
 342         /* PER */
 343         if (per_next_state < PWRDM_POWER_ON)
 344                 omap2_gpio_resume_after_idle();
 345 }
 346
 347 static void omap3_pm_idle(void)
 348 {
 349         if (omap_irq_pending())
 350                 return;
 351
 352         trace_cpu_idle(1, smp_processor_id());
 353
 354         omap_sram_idle();
 355
 356         trace_cpu_idle(PWR_EVENT_EXIT, smp_processor_id());
 357 }
 358
 359 #ifdef CONFIG_SUSPEND
 360 static int omap3_pm_suspend(void)
 361 {
 362         struct power_state *pwrst;
 363         int state, ret = 0;
 364
 365         /* Read current next_pwrsts */
 366         list_for_each_entry(pwrst, &pwrst_list, node)
 367                 pwrst->saved_state = pwrdm_read_next_pwrst(pwrst->pwrdm);
 368         /* Set ones wanted by suspend */
 369         list_for_each_entry(pwrst, &pwrst_list, node) {
 370                 if (omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state))
 371                         goto restore;
 372                 if (pwrdm_clear_all_prev_pwrst(pwrst->pwrdm))
 373                         goto restore;
 374         }
 375
 376         omap3_intc_suspend();
 377
 378         omap_sram_idle();
 379
 380 restore:
 381         /* Restore next_pwrsts */
 382         list_for_each_entry(pwrst, &pwrst_list, node) {
 383                 state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
 384                 if (state > pwrst->next_state) {
 385                         pr_info("Powerdomain (%s) didn't enter target state %d\n",
 386                                 pwrst->pwrdm->name, pwrst->next_state);
 387                         ret = -1;
 388                 }
 389                 omap_set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
 390         }
 391         if (ret)
 392                 pr_err("Could not enter target state in pm_suspend\n");
 393         else
 394                 pr_info("Successfully put all powerdomains to target state\n");
 395
 396         return ret;
 397 }
 398
 399 #endif /* CONFIG_SUSPEND */
 400
 401
 402 /**
 403  * omap3_iva_idle(): ensure IVA is in idle so it can be put into
 404  *                   retention
 405  *
 406  * In cases where IVA2 is activated by bootcode, it may prevent
 407  * full-chip retention or off-mode because it is not idle.  This
 408  * function forces the IVA2 into idle state so it can go
 409  * into retention/off and thus allow full-chip retention/off.
 410  *
 411  **/
 412 static void __init omap3_iva_idle(void)
 413 {
 414         /* ensure IVA2 clock is disabled */
 415         omap2_cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN);
 416
 417         /* if no clock activity, nothing else to do */
 418         if (!(omap2_cm_read_mod_reg(OMAP3430_IVA2_MOD, OMAP3430_CM_CLKSTST) &
 419               OMAP3430_CLKACTIVITY_IVA2_MASK))
 420                 return;
 421
 422         /* Reset IVA2 */
 423         omap2_prm_write_mod_reg(OMAP3430_RST1_IVA2_MASK |
 424                           OMAP3430_RST2_IVA2_MASK |
 425                           OMAP3430_RST3_IVA2_MASK,
 426                           OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 427
 428         /* Enable IVA2 clock */
 429         omap2_cm_write_mod_reg(OMAP3430_CM_FCLKEN_IVA2_EN_IVA2_MASK,
 430                          OMAP3430_IVA2_MOD, CM_FCLKEN);
 431
 432         /* Set IVA2 boot mode to 'idle' */
 433         omap3_ctrl_set_iva_bootmode_idle();
 434
 435         /* Un-reset IVA2 */
 436         omap2_prm_write_mod_reg(0, OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 437
 438         /* Disable IVA2 clock */
 439         omap2_cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN);
 440
 441         /* Reset IVA2 */
 442         omap2_prm_write_mod_reg(OMAP3430_RST1_IVA2_MASK |
 443                           OMAP3430_RST2_IVA2_MASK |
 444                           OMAP3430_RST3_IVA2_MASK,
 445                           OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 446 }
 447
 448 static void __init omap3_d2d_idle(void)
 449 {
 450         u16 mask, padconf;
 451
 452         /* In a stand alone OMAP3430 where there is not a stacked
 453          * modem for the D2D Idle Ack and D2D MStandby must be pulled
 454          * high. S CONTROL_PADCONF_SAD2D_IDLEACK and
 455          * CONTROL_PADCONF_SAD2D_MSTDBY to have a pull up. */
 456         mask = (1 << 4) | (1 << 3); /* pull-up, enabled */
 457         padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_MSTANDBY);
 458         padconf |= mask;
 459         omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_MSTANDBY);
 460
 461         padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_IDLEACK);
 462         padconf |= mask;
 463         omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_IDLEACK);
 464
 465         /* reset modem */
 466         omap2_prm_write_mod_reg(OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RSTPWRON_MASK |
 467                           OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RST_MASK,
 468                           CORE_MOD, OMAP2_RM_RSTCTRL);
 469         omap2_prm_write_mod_reg(0, CORE_MOD, OMAP2_RM_RSTCTRL);
 470 }
 471
 472 static void __init prcm_setup_regs(void)
 473 {
 474         u32 omap3630_en_uart4_mask = cpu_is_omap3630() ?
 475                                         OMAP3630_EN_UART4_MASK : 0;
 476         u32 omap3630_grpsel_uart4_mask = cpu_is_omap3630() ?
 477                                         OMAP3630_GRPSEL_UART4_MASK : 0;
 478
 479         /* XXX This should be handled by hwmod code or SCM init code */
 480         omap_ctrl_writel(OMAP3430_AUTOIDLE_MASK, OMAP2_CONTROL_SYSCONFIG);
 481
 482         /*
 483          * Enable control of expternal oscillator through
 484          * sys_clkreq. In the long run clock framework should
 485          * take care of this.
 486          */
 487         omap2_prm_rmw_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK,
 488                              1 << OMAP_AUTOEXTCLKMODE_SHIFT,
 489                              OMAP3430_GR_MOD,
 490                              OMAP3_PRM_CLKSRC_CTRL_OFFSET);
 491
 492         /* setup wakup source */
 493         omap2_prm_write_mod_reg(OMAP3430_EN_IO_MASK | OMAP3430_EN_GPIO1_MASK |
 494                           OMAP3430_EN_GPT1_MASK | OMAP3430_EN_GPT12_MASK,
 495                           WKUP_MOD, PM_WKEN);
 496         /* No need to write EN_IO, that is always enabled */
 497         omap2_prm_write_mod_reg(OMAP3430_GRPSEL_GPIO1_MASK |
 498                           OMAP3430_GRPSEL_GPT1_MASK |
 499                           OMAP3430_GRPSEL_GPT12_MASK,
 500                           WKUP_MOD, OMAP3430_PM_MPUGRPSEL);
 501
 502         /* Enable PM_WKEN to support DSS LPR */
 503         omap2_prm_write_mod_reg(OMAP3430_PM_WKEN_DSS_EN_DSS_MASK,
 504                                 OMAP3430_DSS_MOD, PM_WKEN);
 505
 506         /* Enable wakeups in PER */
 507         omap2_prm_write_mod_reg(omap3630_en_uart4_mask |
 508                           OMAP3430_EN_GPIO2_MASK | OMAP3430_EN_GPIO3_MASK |
 509                           OMAP3430_EN_GPIO4_MASK | OMAP3430_EN_GPIO5_MASK |
 510                           OMAP3430_EN_GPIO6_MASK | OMAP3430_EN_UART3_MASK |
 511                           OMAP3430_EN_MCBSP2_MASK | OMAP3430_EN_MCBSP3_MASK |
 512                           OMAP3430_EN_MCBSP4_MASK,
 513                           OMAP3430_PER_MOD, PM_WKEN);
 514         /* and allow them to wake up MPU */
 515         omap2_prm_write_mod_reg(omap3630_grpsel_uart4_mask |
 516                           OMAP3430_GRPSEL_GPIO2_MASK |
 517                           OMAP3430_GRPSEL_GPIO3_MASK |
 518                           OMAP3430_GRPSEL_GPIO4_MASK |
 519                           OMAP3430_GRPSEL_GPIO5_MASK |
 520                           OMAP3430_GRPSEL_GPIO6_MASK |
 521                           OMAP3430_GRPSEL_UART3_MASK |
 522                           OMAP3430_GRPSEL_MCBSP2_MASK |
 523                           OMAP3430_GRPSEL_MCBSP3_MASK |
 524                           OMAP3430_GRPSEL_MCBSP4_MASK,
 525                           OMAP3430_PER_MOD, OMAP3430_PM_MPUGRPSEL);
 526
 527         /* Don't attach IVA interrupts */
 528         if (omap3_has_iva()) {
 529                 omap2_prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
 530                 omap2_prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);
 531                 omap2_prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3);
 532                 omap2_prm_write_mod_reg(0, OMAP3430_PER_MOD,
 533                                         OMAP3430_PM_IVAGRPSEL);
 534         }
 535
 536         /* Clear any pending 'reset' flags */
 537         omap2_prm_write_mod_reg(0xffffffff, MPU_MOD, OMAP2_RM_RSTST);
 538         omap2_prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP2_RM_RSTST);
 539         omap2_prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, OMAP2_RM_RSTST);
 540         omap2_prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, OMAP2_RM_RSTST);
 541         omap2_prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, OMAP2_RM_RSTST);
 542         omap2_prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, OMAP2_RM_RSTST);
 543         omap2_prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, OMAP2_RM_RSTST);
 544
 545         /* Clear any pending PRCM interrupts */
 546         omap2_prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 547
 548         /*
 549          * We need to idle iva2_pwrdm even on am3703 with no iva2.
 550          */
 551         omap3_iva_idle();
 552
 553         omap3_d2d_idle();
 554 }
 555
 556 void omap3_pm_off_mode_enable(int enable)
 557 {
 558         struct power_state *pwrst;
 559         u32 state;
 560
 561         if (enable)
 562                 state = PWRDM_POWER_OFF;
 563         else
 564                 state = PWRDM_POWER_RET;
 565
 566         list_for_each_entry(pwrst, &pwrst_list, node) {
 567                 if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583) &&
 568                                 pwrst->pwrdm == core_pwrdm &&
 569                                 state == PWRDM_POWER_OFF) {
 570                         pwrst->next_state = PWRDM_POWER_RET;
 571                         pr_warn("%s: Core OFF disabled due to errata i583\n",
 572                                 __func__);
 573                 } else {
 574                         pwrst->next_state = state;
 575                 }
 576                 omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state);
 577         }
 578 }
 579
 580 int omap3_pm_get_suspend_state(struct powerdomain *pwrdm)
 581 {
 582         struct power_state *pwrst;
 583
 584         list_for_each_entry(pwrst, &pwrst_list, node) {
 585                 if (pwrst->pwrdm == pwrdm)
 586                         return pwrst->next_state;
 587         }
 588         return -EINVAL;
 589 }
 590
 591 int omap3_pm_set_suspend_state(struct powerdomain *pwrdm, int state)
 592 {
 593         struct power_state *pwrst;
 594
 595         list_for_each_entry(pwrst, &pwrst_list, node) {
 596                 if (pwrst->pwrdm == pwrdm) {
 597                         pwrst->next_state = state;
 598                         return 0;
 599                 }
 600         }
 601         return -EINVAL;
 602 }
 603
 604 static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
 605 {
 606         struct power_state *pwrst;
 607
 608         if (!pwrdm->pwrsts)
 609                 return 0;
 610
 611         pwrst = kmalloc(sizeof(struct power_state), GFP_ATOMIC);
 612         if (!pwrst)
 613                 return -ENOMEM;
 614         pwrst->pwrdm = pwrdm;
 615         pwrst->next_state = PWRDM_POWER_RET;
 616         list_add(&pwrst->node, &pwrst_list);
 617
 618         if (pwrdm_has_hdwr_sar(pwrdm))
 619                 pwrdm_enable_hdwr_sar(pwrdm);
 620
 621         return omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state);
 622 }
 623
 624 /*
 625  * Push functions to SRAM
 626  *
 627  * The minimum set of functions is pushed to SRAM for execution:
 628  * - omap3_do_wfi for erratum i581 WA,
 629  * - save_secure_ram_context for security extensions.
 630  */
 631 void omap_push_sram_idle(void)
 632 {
 633         omap3_do_wfi_sram = omap_sram_push(omap3_do_wfi, omap3_do_wfi_sz);
 634
 635         if (omap_type() != OMAP2_DEVICE_TYPE_GP)
 636                 _omap_save_secure_sram = omap_sram_push(save_secure_ram_context,
 637                                 save_secure_ram_context_sz);
 638 }
 639
 640 static void __init pm_errata_configure(void)
 641 {
 642         if (cpu_is_omap3630()) {
 643                 pm34xx_errata |= PM_RTA_ERRATUM_i608;
 644                 /* Enable the l2 cache toggling in sleep logic */
 645                 enable_omap3630_toggle_l2_on_restore();
 646                 if (omap_rev() < OMAP3630_REV_ES1_2)
 647                         pm34xx_errata |= (PM_SDRC_WAKEUP_ERRATUM_i583 |
 648                                           PM_PER_MEMORIES_ERRATUM_i582);
 649         } else if (cpu_is_omap34xx()) {
 650                 pm34xx_errata |= PM_PER_MEMORIES_ERRATUM_i582;
 651         }
 652 }
 653
 654 int __init omap3_pm_init(void)
 655 {
 656         struct power_state *pwrst, *tmp;
 657         struct clockdomain *neon_clkdm, *mpu_clkdm, *per_clkdm, *wkup_clkdm;
 658         int ret;
 659
 660         if (!omap3_has_io_chain_ctrl())
 661                 pr_warning("PM: no software I/O chain control; some wakeups may be lost\n");
 662
 663         pm_errata_configure();
 664
 665         /* XXX prcm_setup_regs needs to be before enabling hw
 666          * supervised mode for powerdomains */
 667         prcm_setup_regs();
 668
 669         ret = request_irq(omap_prcm_event_to_irq("wkup"),
 670                 _prcm_int_handle_wakeup, IRQF_NO_SUSPEND, "pm_wkup", NULL);
 671
 672         if (ret) {
 673                 pr_err("pm: Failed to request pm_wkup irq\n");
 674                 goto err1;
 675         }
 676
 677         /* IO interrupt is shared with mux code */
 678         ret = request_irq(omap_prcm_event_to_irq("io"),
 679                 _prcm_int_handle_io, IRQF_SHARED | IRQF_NO_SUSPEND, "pm_io",
 680                 omap3_pm_init);
 681         enable_irq(omap_prcm_event_to_irq("io"));
 682
 683         if (ret) {
 684                 pr_err("pm: Failed to request pm_io irq\n");
 685                 goto err2;
 686         }
 687
 688         ret = pwrdm_for_each(pwrdms_setup, NULL);
 689         if (ret) {
 690                 pr_err("Failed to setup powerdomains\n");
 691                 goto err3;
 692         }
 693
 694         (void) clkdm_for_each(omap_pm_clkdms_setup, NULL);
 695
 696         mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
 697         if (mpu_pwrdm == NULL) {
 698                 pr_err("Failed to get mpu_pwrdm\n");
 699                 ret = -EINVAL;
 700                 goto err3;
 701         }
 702
 703         neon_pwrdm = pwrdm_lookup("neon_pwrdm");
 704         per_pwrdm = pwrdm_lookup("per_pwrdm");
 705         core_pwrdm = pwrdm_lookup("core_pwrdm");
 706
 707         neon_clkdm = clkdm_lookup("neon_clkdm");
 708         mpu_clkdm = clkdm_lookup("mpu_clkdm");
 709         per_clkdm = clkdm_lookup("per_clkdm");
 710         wkup_clkdm = clkdm_lookup("wkup_clkdm");
 711
 712 #ifdef CONFIG_SUSPEND
 713         omap_pm_suspend = omap3_pm_suspend;
 714 #endif
 715
 716         arm_pm_idle = omap3_pm_idle;
 717         omap3_idle_init();
 718
 719         /*
 720          * RTA is disabled during initialization as per erratum i608
 721          * it is safer to disable RTA by the bootloader, but we would like
 722          * to be doubly sure here and prevent any mishaps.
 723          */
 724         if (IS_PM34XX_ERRATUM(PM_RTA_ERRATUM_i608))
 725                 omap3630_ctrl_disable_rta();
 726
 727         /*
 728          * The UART3/4 FIFO and the sidetone memory in McBSP2/3 are
 729          * not correctly reset when the PER powerdomain comes back
 730          * from OFF or OSWR when the CORE powerdomain is kept active.
 731          * See OMAP36xx Erratum i582 "PER Domain reset issue after
 732          * Domain-OFF/OSWR Wakeup".  This wakeup dependency is not a
 733          * complete workaround.  The kernel must also prevent the PER
 734          * powerdomain from going to OSWR/OFF while the CORE
 735          * powerdomain is not going to OSWR/OFF.  And if PER last
 736          * power state was off while CORE last power state was ON, the
 737          * UART3/4 and McBSP2/3 SIDETONE devices need to run a
 738          * self-test using their loopback tests; if that fails, those
 739          * devices are unusable until the PER/CORE can complete a transition
 740          * from ON to OSWR/OFF and then back to ON.
 741          *
 742          * XXX Technically this workaround is only needed if off-mode
 743          * or OSWR is enabled.
 744          */
 745         if (IS_PM34XX_ERRATUM(PM_PER_MEMORIES_ERRATUM_i582))
 746                 clkdm_add_wkdep(per_clkdm, wkup_clkdm);
 747
 748         clkdm_add_wkdep(neon_clkdm, mpu_clkdm);
 749         if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
 750                 omap3_secure_ram_storage =
 751                         kmalloc(0x803F, GFP_KERNEL);
 752                 if (!omap3_secure_ram_storage)
 753                         pr_err("Memory allocation failed when allocating for secure sram context\n");
 754
 755                 local_irq_disable();
 756
 757                 omap_dma_global_context_save();
 758                 omap3_save_secure_ram_context();
 759                 omap_dma_global_context_restore();
 760
 761                 local_irq_enable();
 762         }
 763
 764         omap3_save_scratchpad_contents();
 765         return ret;
 766
 767 err3:
 768         list_for_each_entry_safe(pwrst, tmp, &pwrst_list, node) {
 769                 list_del(&pwrst->node);
 770                 kfree(pwrst);
 771         }
 772         free_irq(omap_prcm_event_to_irq("io"), omap3_pm_init);
 773 err2:
 774         free_irq(omap_prcm_event_to_irq("wkup"), NULL);
 775 err1:
 776         return ret;
 777 }