drivers/tty/serial/pmac_zilog.h

   1 #ifndef __PMAC_ZILOG_H__
   2 #define __PMAC_ZILOG_H__
   3
   4 /*
   5  * At most 2 ESCCs with 2 ports each
   6  */
   7 #define MAX_ZS_PORTS    4
   8
   9 /*
  10  * We wrap our port structure around the generic uart_port.
  11  */
  12 #define NUM_ZSREGS    17
  13
  14 struct uart_pmac_port {
  15         struct uart_port                port;
  16         struct uart_pmac_port           *mate;
  17
  18 #ifdef CONFIG_PPC_PMAC
  19         /* macio_dev for the escc holding this port (maybe be null on
  20          * early inited port)
  21          */
  22         struct macio_dev                *dev;
  23         /* device node to this port, this points to one of 2 childs
  24          * of "escc" node (ie. ch-a or ch-b)
  25          */
  26         struct device_node              *node;
  27 #else
  28         struct platform_device          *pdev;
  29 #endif
  30
  31         /* Port type as obtained from device tree (IRDA, modem, ...) */
  32         int                             port_type;
  33         u8                              curregs[NUM_ZSREGS];
  34
  35         unsigned int                    flags;
  36 #define PMACZILOG_FLAG_IS_CONS          0x00000001
  37 #define PMACZILOG_FLAG_IS_KGDB          0x00000002
  38 #define PMACZILOG_FLAG_MODEM_STATUS     0x00000004
  39 #define PMACZILOG_FLAG_IS_CHANNEL_A     0x00000008
  40 #define PMACZILOG_FLAG_REGS_HELD        0x00000010
  41 #define PMACZILOG_FLAG_TX_STOPPED       0x00000020
  42 #define PMACZILOG_FLAG_TX_ACTIVE        0x00000040
  43 #define PMACZILOG_FLAG_IS_IRDA          0x00000100
  44 #define PMACZILOG_FLAG_IS_INTMODEM      0x00000200
  45 #define PMACZILOG_FLAG_HAS_DMA          0x00000400
  46 #define PMACZILOG_FLAG_RSRC_REQUESTED   0x00000800
  47 #define PMACZILOG_FLAG_IS_OPEN          0x00002000
  48 #define PMACZILOG_FLAG_IS_EXTCLK        0x00008000
  49 #define PMACZILOG_FLAG_BREAK            0x00010000
  50
  51         unsigned char                   parity_mask;
  52         unsigned char                   prev_status;
  53
  54         volatile u8                     __iomem *control_reg;
  55         volatile u8                     __iomem *data_reg;
  56
  57 #ifdef CONFIG_PPC_PMAC
  58         unsigned int                    tx_dma_irq;
  59         unsigned int                    rx_dma_irq;
  60         volatile struct dbdma_regs      __iomem *tx_dma_regs;
  61         volatile struct dbdma_regs      __iomem *rx_dma_regs;
  62 #endif
  63
  64         unsigned char                   irq_name[8];
  65
  66         struct ktermios                 termios_cache;
  67 };
  68
  69 #define to_pmz(p) ((struct uart_pmac_port *)(p))
  70
  71 static inline struct uart_pmac_port *pmz_get_port_A(struct uart_pmac_port *uap)
  72 {
  73         if (uap->flags & PMACZILOG_FLAG_IS_CHANNEL_A)
  74                 return uap;
  75         return uap->mate;
  76 }
  77
  78 /*
  79  * Register accessors. Note that we don't need to enforce a recovery
  80  * delay on PCI PowerMac hardware, it's dealt in HW by the MacIO chip,
  81  * though if we try to use this driver on older machines, we might have
  82  * to add it back
  83  */
  84 static inline u8 read_zsreg(struct uart_pmac_port *port, u8 reg)
  85 {
  86         if (reg != 0)
  87                 writeb(reg, port->control_reg);
  88         return readb(port->control_reg);
  89 }
  90
  91 static inline void write_zsreg(struct uart_pmac_port *port, u8 reg, u8 value)
  92 {
  93         if (reg != 0)
  94                 writeb(reg, port->control_reg);
  95         writeb(value, port->control_reg);
  96 }
  97
  98 static inline u8 read_zsdata(struct uart_pmac_port *port)
  99 {
 100         return readb(port->data_reg);
 101 }
 102
 103 static inline void write_zsdata(struct uart_pmac_port *port, u8 data)
 104 {
 105         writeb(data, port->data_reg);
 106 }
 107
 108 static inline void zssync(struct uart_pmac_port *port)
 109 {
 110         (void)readb(port->control_reg);
 111 }
 112
 113 /* Conversion routines to/from brg time constants from/to bits
 114  * per second.
 115  */
 116 #define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
 117 #define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
 118
 119 #define ZS_CLOCK         3686400        /* Z8530 RTxC input clock rate */
 120
 121 /* The Zilog register set */
 122
 123 #define FLAG    0x7e
 124
 125 /* Write Register 0 */
 126 #define R0      0               /* Register selects */
 127 #define R1      1
 128 #define R2      2
 129 #define R3      3
 130 #define R4      4
 131 #define R5      5
 132 #define R6      6
 133 #define R7      7
 134 #define R8      8
 135 #define R9      9
 136 #define R10     10
 137 #define R11     11
 138 #define R12     12
 139 #define R13     13
 140 #define R14     14
 141 #define R15     15
 142 #define R7P     16
 143
 144 #define NULLCODE        0       /* Null Code */
 145 #define POINT_HIGH      0x8     /* Select upper half of registers */
 146 #define RES_EXT_INT     0x10    /* Reset Ext. Status Interrupts */
 147 #define SEND_ABORT      0x18    /* HDLC Abort */
 148 #define RES_RxINT_FC    0x20    /* Reset RxINT on First Character */
 149 #define RES_Tx_P        0x28    /* Reset TxINT Pending */
 150 #define ERR_RES         0x30    /* Error Reset */
 151 #define RES_H_IUS       0x38    /* Reset highest IUS */
 152
 153 #define RES_Rx_CRC      0x40    /* Reset Rx CRC Checker */
 154 #define RES_Tx_CRC      0x80    /* Reset Tx CRC Checker */
 155 #define RES_EOM_L       0xC0    /* Reset EOM latch */
 156
 157 /* Write Register 1 */
 158
 159 #define EXT_INT_ENAB    0x1     /* Ext Int Enable */
 160 #define TxINT_ENAB      0x2     /* Tx Int Enable */
 161 #define PAR_SPEC        0x4     /* Parity is special condition */
 162
 163 #define RxINT_DISAB     0       /* Rx Int Disable */
 164 #define RxINT_FCERR     0x8     /* Rx Int on First Character Only or Error */
 165 #define INT_ALL_Rx      0x10    /* Int on all Rx Characters or error */
 166 #define INT_ERR_Rx      0x18    /* Int on error only */
 167 #define RxINT_MASK      0x18
 168
 169 #define WT_RDY_RT       0x20    /* W/Req reflects recv if 1, xmit if 0 */
 170 #define WT_FN_RDYFN     0x40    /* W/Req pin is DMA request if 1, wait if 0 */
 171 #define WT_RDY_ENAB     0x80    /* Enable W/Req pin */
 172
 173 /* Write Register #2 (Interrupt Vector) */
 174
 175 /* Write Register 3 */
 176
 177 #define RxENABLE        0x1     /* Rx Enable */
 178 #define SYNC_L_INH      0x2     /* Sync Character Load Inhibit */
 179 #define ADD_SM          0x4     /* Address Search Mode (SDLC) */
 180 #define RxCRC_ENAB      0x8     /* Rx CRC Enable */
 181 #define ENT_HM          0x10    /* Enter Hunt Mode */
 182 #define AUTO_ENAB       0x20    /* Auto Enables */
 183 #define Rx5             0x0     /* Rx 5 Bits/Character */
 184 #define Rx7             0x40    /* Rx 7 Bits/Character */
 185 #define Rx6             0x80    /* Rx 6 Bits/Character */
 186 #define Rx8             0xc0    /* Rx 8 Bits/Character */
 187 #define RxN_MASK        0xc0
 188
 189 /* Write Register 4 */
 190
 191 #define PAR_ENAB        0x1     /* Parity Enable */
 192 #define PAR_EVEN        0x2     /* Parity Even/Odd* */
 193
 194 #define SYNC_ENAB       0       /* Sync Modes Enable */
 195 #define SB1             0x4     /* 1 stop bit/char */
 196 #define SB15            0x8     /* 1.5 stop bits/char */
 197 #define SB2             0xc     /* 2 stop bits/char */
 198 #define SB_MASK         0xc
 199
 200 #define MONSYNC         0       /* 8 Bit Sync character */
 201 #define BISYNC          0x10    /* 16 bit sync character */
 202 #define SDLC            0x20    /* SDLC Mode (01111110 Sync Flag) */
 203 #define EXTSYNC         0x30    /* External Sync Mode */
 204
 205 #define X1CLK           0x0     /* x1 clock mode */
 206 #define X16CLK          0x40    /* x16 clock mode */
 207 #define X32CLK          0x80    /* x32 clock mode */
 208 #define X64CLK          0xC0    /* x64 clock mode */
 209 #define XCLK_MASK       0xC0
 210
 211 /* Write Register 5 */
 212
 213 #define TxCRC_ENAB      0x1     /* Tx CRC Enable */
 214 #define RTS             0x2     /* RTS */
 215 #define SDLC_CRC        0x4     /* SDLC/CRC-16 */
 216 #define TxENABLE        0x8     /* Tx Enable */
 217 #define SND_BRK         0x10    /* Send Break */
 218 #define Tx5             0x0     /* Tx 5 bits (or less)/character */
 219 #define Tx7             0x20    /* Tx 7 bits/character */
 220 #define Tx6             0x40    /* Tx 6 bits/character */
 221 #define Tx8             0x60    /* Tx 8 bits/character */
 222 #define TxN_MASK        0x60
 223 #define DTR             0x80    /* DTR */
 224
 225 /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
 226
 227 /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
 228
 229 /* Write Register 7' (Some enhanced feature control) */
 230 #define ENEXREAD        0x40    /* Enable read of some write registers */
 231
 232 /* Write Register 8 (transmit buffer) */
 233
 234 /* Write Register 9 (Master interrupt control) */
 235 #define VIS     1       /* Vector Includes Status */
 236 #define NV      2       /* No Vector */
 237 #define DLC     4       /* Disable Lower Chain */
 238 #define MIE     8       /* Master Interrupt Enable */
 239 #define STATHI  0x10    /* Status high */
 240 #define NORESET 0       /* No reset on write to R9 */
 241 #define CHRB    0x40    /* Reset channel B */
 242 #define CHRA    0x80    /* Reset channel A */
 243 #define FHWRES  0xc0    /* Force hardware reset */
 244
 245 /* Write Register 10 (misc control bits) */
 246 #define BIT6    1       /* 6 bit/8bit sync */
 247 #define LOOPMODE 2      /* SDLC Loop mode */
 248 #define ABUNDER 4       /* Abort/flag on SDLC xmit underrun */
 249 #define MARKIDLE 8      /* Mark/flag on idle */
 250 #define GAOP    0x10    /* Go active on poll */
 251 #define NRZ     0       /* NRZ mode */
 252 #define NRZI    0x20    /* NRZI mode */
 253 #define FM1     0x40    /* FM1 (transition = 1) */
 254 #define FM0     0x60    /* FM0 (transition = 0) */
 255 #define CRCPS   0x80    /* CRC Preset I/O */
 256
 257 /* Write Register 11 (Clock Mode control) */
 258 #define TRxCXT  0       /* TRxC = Xtal output */
 259 #define TRxCTC  1       /* TRxC = Transmit clock */
 260 #define TRxCBR  2       /* TRxC = BR Generator Output */
 261 #define TRxCDP  3       /* TRxC = DPLL output */
 262 #define TRxCOI  4       /* TRxC O/I */
 263 #define TCRTxCP 0       /* Transmit clock = RTxC pin */
 264 #define TCTRxCP 8       /* Transmit clock = TRxC pin */
 265 #define TCBR    0x10    /* Transmit clock = BR Generator output */
 266 #define TCDPLL  0x18    /* Transmit clock = DPLL output */
 267 #define RCRTxCP 0       /* Receive clock = RTxC pin */
 268 #define RCTRxCP 0x20    /* Receive clock = TRxC pin */
 269 #define RCBR    0x40    /* Receive clock = BR Generator output */
 270 #define RCDPLL  0x60    /* Receive clock = DPLL output */
 271 #define RTxCX   0x80    /* RTxC Xtal/No Xtal */
 272
 273 /* Write Register 12 (lower byte of baud rate generator time constant) */
 274
 275 /* Write Register 13 (upper byte of baud rate generator time constant) */
 276
 277 /* Write Register 14 (Misc control bits) */
 278 #define BRENAB  1       /* Baud rate generator enable */
 279 #define BRSRC   2       /* Baud rate generator source */
 280 #define DTRREQ  4       /* DTR/Request function */
 281 #define AUTOECHO 8      /* Auto Echo */
 282 #define LOOPBAK 0x10    /* Local loopback */
 283 #define SEARCH  0x20    /* Enter search mode */
 284 #define RMC     0x40    /* Reset missing clock */
 285 #define DISDPLL 0x60    /* Disable DPLL */
 286 #define SSBR    0x80    /* Set DPLL source = BR generator */
 287 #define SSRTxC  0xa0    /* Set DPLL source = RTxC */
 288 #define SFMM    0xc0    /* Set FM mode */
 289 #define SNRZI   0xe0    /* Set NRZI mode */
 290
 291 /* Write Register 15 (external/status interrupt control) */
 292 #define EN85C30 1       /* Enable some 85c30-enhanced registers */
 293 #define ZCIE    2       /* Zero count IE */
 294 #define ENSTFIFO 4      /* Enable status FIFO (SDLC) */
 295 #define DCDIE   8       /* DCD IE */
 296 #define SYNCIE  0x10    /* Sync/hunt IE */
 297 #define CTSIE   0x20    /* CTS IE */
 298 #define TxUIE   0x40    /* Tx Underrun/EOM IE */
 299 #define BRKIE   0x80    /* Break/Abort IE */
 300
 301
 302 /* Read Register 0 */
 303 #define Rx_CH_AV        0x1     /* Rx Character Available */
 304 #define ZCOUNT          0x2     /* Zero count */
 305 #define Tx_BUF_EMP      0x4     /* Tx Buffer empty */
 306 #define DCD             0x8     /* DCD */
 307 #define SYNC_HUNT       0x10    /* Sync/hunt */
 308 #define CTS             0x20    /* CTS */
 309 #define TxEOM           0x40    /* Tx underrun */
 310 #define BRK_ABRT        0x80    /* Break/Abort */
 311
 312 /* Read Register 1 */
 313 #define ALL_SNT         0x1     /* All sent */
 314 /* Residue Data for 8 Rx bits/char programmed */
 315 #define RES3            0x8     /* 0/3 */
 316 #define RES4            0x4     /* 0/4 */
 317 #define RES5            0xc     /* 0/5 */
 318 #define RES6            0x2     /* 0/6 */
 319 #define RES7            0xa     /* 0/7 */
 320 #define RES8            0x6     /* 0/8 */
 321 #define RES18           0xe     /* 1/8 */
 322 #define RES28           0x0     /* 2/8 */
 323 /* Special Rx Condition Interrupts */
 324 #define PAR_ERR         0x10    /* Parity error */
 325 #define Rx_OVR          0x20    /* Rx Overrun Error */
 326 #define CRC_ERR         0x40    /* CRC/Framing Error */
 327 #define END_FR          0x80    /* End of Frame (SDLC) */
 328
 329 /* Read Register 2 (channel b only) - Interrupt vector */
 330 #define CHB_Tx_EMPTY    0x00
 331 #define CHB_EXT_STAT    0x02
 332 #define CHB_Rx_AVAIL    0x04
 333 #define CHB_SPECIAL     0x06
 334 #define CHA_Tx_EMPTY    0x08
 335 #define CHA_EXT_STAT    0x0a
 336 #define CHA_Rx_AVAIL    0x0c
 337 #define CHA_SPECIAL     0x0e
 338 #define STATUS_MASK     0x06
 339
 340 /* Read Register 3 (interrupt pending register) ch a only */
 341 #define CHBEXT  0x1             /* Channel B Ext/Stat IP */
 342 #define CHBTxIP 0x2             /* Channel B Tx IP */
 343 #define CHBRxIP 0x4             /* Channel B Rx IP */
 344 #define CHAEXT  0x8             /* Channel A Ext/Stat IP */
 345 #define CHATxIP 0x10            /* Channel A Tx IP */
 346 #define CHARxIP 0x20            /* Channel A Rx IP */
 347
 348 /* Read Register 8 (receive data register) */
 349
 350 /* Read Register 10  (misc status bits) */
 351 #define ONLOOP  2               /* On loop */
 352 #define LOOPSEND 0x10           /* Loop sending */
 353 #define CLK2MIS 0x40            /* Two clocks missing */
 354 #define CLK1MIS 0x80            /* One clock missing */
 355
 356 /* Read Register 12 (lower byte of baud rate generator constant) */
 357
 358 /* Read Register 13 (upper byte of baud rate generator constant) */
 359
 360 /* Read Register 15 (value of WR 15) */
 361
 362 /* Misc macros */
 363 #define ZS_CLEARERR(port)    (write_zsreg(port, 0, ERR_RES))
 364 #define ZS_CLEARFIFO(port)   do { volatile unsigned char garbage; \
 365                                      garbage = read_zsdata(port); \
 366                                      garbage = read_zsdata(port); \
 367                                      garbage = read_zsdata(port); \
 368                                 } while(0)
 369
 370 #define ZS_IS_CONS(UP)                  ((UP)->flags & PMACZILOG_FLAG_IS_CONS)
 371 #define ZS_IS_KGDB(UP)                  ((UP)->flags & PMACZILOG_FLAG_IS_KGDB)
 372 #define ZS_IS_CHANNEL_A(UP)             ((UP)->flags & PMACZILOG_FLAG_IS_CHANNEL_A)
 373 #define ZS_REGS_HELD(UP)                ((UP)->flags & PMACZILOG_FLAG_REGS_HELD)
 374 #define ZS_TX_STOPPED(UP)               ((UP)->flags & PMACZILOG_FLAG_TX_STOPPED)
 375 #define ZS_TX_ACTIVE(UP)                ((UP)->flags & PMACZILOG_FLAG_TX_ACTIVE)
 376 #define ZS_WANTS_MODEM_STATUS(UP)       ((UP)->flags & PMACZILOG_FLAG_MODEM_STATUS)
 377 #define ZS_IS_IRDA(UP)                  ((UP)->flags & PMACZILOG_FLAG_IS_IRDA)
 378 #define ZS_IS_INTMODEM(UP)              ((UP)->flags & PMACZILOG_FLAG_IS_INTMODEM)
 379 #define ZS_HAS_DMA(UP)                  ((UP)->flags & PMACZILOG_FLAG_HAS_DMA)
 380 #define ZS_IS_OPEN(UP)                  ((UP)->flags & PMACZILOG_FLAG_IS_OPEN)
 381 #define ZS_IS_EXTCLK(UP)                ((UP)->flags & PMACZILOG_FLAG_IS_EXTCLK)
 382
 383 #endif /* __PMAC_ZILOG_H__ */