irqchip/ts4800: Add TS-4800 interrupt controller

[linux/fpc-iii.git] / drivers / usb / host / ehci.h

/*
 * Copyright (c) 2001-2002 by David Brownell
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the
 * Free Software Foundation; either version 2 of the License, or (at your
 * option) any later version.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
 * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
 * for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software Foundation,
 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

#ifndef __LINUX_EHCI_HCD_H
#define __LINUX_EHCI_HCD_H

/* definitions used for the EHCI driver */

/*
 * __hc32 and __hc16 are "Host Controller" types, they may be equivalent to
 * __leXX (normally) or __beXX (given EHCI_BIG_ENDIAN_DESC), depending on
 * the host controller implementation.
 *
 * To facilitate the strongest possible byte-order checking from "sparse"
 * and so on, we use __leXX unless that's not practical.
 */
#ifdef CONFIG_USB_EHCI_BIG_ENDIAN_DESC
typedef __u32 __bitwise __hc32;
typedef __u16 __bitwise __hc16;
#else
#define __hc32  __le32
#define __hc16  __le16
#endif

/* statistics can be kept for tuning/monitoring */
#ifdef CONFIG_DYNAMIC_DEBUG
#define EHCI_STATS
#endif

struct ehci_stats {
        /* irq usage */
        unsigned long           normal;
        unsigned long           error;
        unsigned long           iaa;
        unsigned long           lost_iaa;

        /* termination of urbs from core */
        unsigned long           complete;
        unsigned long           unlink;
};

/*
 * Scheduling and budgeting information for periodic transfers, for both
 * high-speed devices and full/low-speed devices lying behind a TT.
 */
struct ehci_per_sched {
        struct usb_device       *udev;          /* access to the TT */
        struct usb_host_endpoint *ep;
        struct list_head        ps_list;        /* node on ehci_tt's ps_list */
        u16                     tt_usecs;       /* time on the FS/LS bus */
        u16                     cs_mask;        /* C-mask and S-mask bytes */
        u16                     period;         /* actual period in frames */
        u16                     phase;          /* actual phase, frame part */
        u8                      bw_phase;       /* same, for bandwidth
                                                   reservation */
        u8                      phase_uf;       /* uframe part of the phase */
        u8                      usecs, c_usecs; /* times on the HS bus */
        u8                      bw_uperiod;     /* period in microframes, for
                                                   bandwidth reservation */
        u8                      bw_period;      /* same, in frames */
};
#define NO_FRAME        29999                   /* frame not assigned yet */

/* ehci_hcd->lock guards shared data against other CPUs:
 *   ehci_hcd:  async, unlink, periodic (and shadow), ...
 *   usb_host_endpoint: hcpriv
 *   ehci_qh:   qh_next, qtd_list
 *   ehci_qtd:  qtd_list
 *
 * Also, hold this lock when talking to HC registers or
 * when updating hw_* fields in shared qh/qtd/... structures.
 */

#define EHCI_MAX_ROOT_PORTS     15              /* see HCS_N_PORTS */

/*
 * ehci_rh_state values of EHCI_RH_RUNNING or above mean that the
 * controller may be doing DMA.  Lower values mean there's no DMA.
 */
enum ehci_rh_state {
        EHCI_RH_HALTED,
        EHCI_RH_SUSPENDED,
        EHCI_RH_RUNNING,
        EHCI_RH_STOPPING
};

/*
 * Timer events, ordered by increasing delay length.
 * Always update event_delays_ns[] and event_handlers[] (defined in
 * ehci-timer.c) in parallel with this list.
 */
enum ehci_hrtimer_event {
        EHCI_HRTIMER_POLL_ASS,          /* Poll for async schedule off */
        EHCI_HRTIMER_POLL_PSS,          /* Poll for periodic schedule off */
        EHCI_HRTIMER_POLL_DEAD,         /* Wait for dead controller to stop */
        EHCI_HRTIMER_UNLINK_INTR,       /* Wait for interrupt QH unlink */
        EHCI_HRTIMER_FREE_ITDS,         /* Wait for unused iTDs and siTDs */
        EHCI_HRTIMER_START_UNLINK_INTR, /* Unlink empty interrupt QHs */
        EHCI_HRTIMER_ASYNC_UNLINKS,     /* Unlink empty async QHs */
        EHCI_HRTIMER_IAA_WATCHDOG,      /* Handle lost IAA interrupts */
        EHCI_HRTIMER_DISABLE_PERIODIC,  /* Wait to disable periodic sched */
        EHCI_HRTIMER_DISABLE_ASYNC,     /* Wait to disable async sched */
        EHCI_HRTIMER_IO_WATCHDOG,       /* Check for missing IRQs */
        EHCI_HRTIMER_NUM_EVENTS         /* Must come last */
};
#define EHCI_HRTIMER_NO_EVENT   99

struct ehci_hcd {                       /* one per controller */
        /* timing support */
        enum ehci_hrtimer_event next_hrtimer_event;
        unsigned                enabled_hrtimer_events;
        ktime_t                 hr_timeouts[EHCI_HRTIMER_NUM_EVENTS];
        struct hrtimer          hrtimer;

        int                     PSS_poll_count;
        int                     ASS_poll_count;
        int                     died_poll_count;

        /* glue to PCI and HCD framework */
        struct ehci_caps __iomem *caps;
        struct ehci_regs __iomem *regs;
        struct ehci_dbg_port __iomem *debug;

        __u32                   hcs_params;     /* cached register copy */
        spinlock_t              lock;
        enum ehci_rh_state      rh_state;

        /* general schedule support */
        bool                    scanning:1;
        bool                    need_rescan:1;
        bool                    intr_unlinking:1;
        bool                    iaa_in_progress:1;
        bool                    async_unlinking:1;
        bool                    shutdown:1;
        struct ehci_qh          *qh_scan_next;

        /* async schedule support */
        struct ehci_qh          *async;
        struct ehci_qh          *dummy;         /* For AMD quirk use */
        struct list_head        async_unlink;
        struct list_head        async_idle;
        unsigned                async_unlink_cycle;
        unsigned                async_count;    /* async activity count */

        /* periodic schedule support */
#define DEFAULT_I_TDPS          1024            /* some HCs can do less */
        unsigned                periodic_size;
        __hc32                  *periodic;      /* hw periodic table */
        dma_addr_t              periodic_dma;
        struct list_head        intr_qh_list;
        unsigned                i_thresh;       /* uframes HC might cache */

        union ehci_shadow       *pshadow;       /* mirror hw periodic table */
        struct list_head        intr_unlink_wait;
        struct list_head        intr_unlink;
        unsigned                intr_unlink_wait_cycle;
        unsigned                intr_unlink_cycle;
        unsigned                now_frame;      /* frame from HC hardware */
        unsigned                last_iso_frame; /* last frame scanned for iso */
        unsigned                intr_count;     /* intr activity count */
        unsigned                isoc_count;     /* isoc activity count */
        unsigned                periodic_count; /* periodic activity count */
        unsigned                uframe_periodic_max; /* max periodic time per uframe */


        /* list of itds & sitds completed while now_frame was still active */
        struct list_head        cached_itd_list;
        struct ehci_itd         *last_itd_to_free;
        struct list_head        cached_sitd_list;
        struct ehci_sitd        *last_sitd_to_free;

        /* per root hub port */
        unsigned long           reset_done [EHCI_MAX_ROOT_PORTS];

        /* bit vectors (one bit per port) */
        unsigned long           bus_suspended;          /* which ports were
                        already suspended at the start of a bus suspend */
        unsigned long           companion_ports;        /* which ports are
                        dedicated to the companion controller */
        unsigned long           owned_ports;            /* which ports are
                        owned by the companion during a bus suspend */
        unsigned long           port_c_suspend;         /* which ports have
                        the change-suspend feature turned on */
        unsigned long           suspended_ports;        /* which ports are
                        suspended */
        unsigned long           resuming_ports;         /* which ports have
                        started to resume */

        /* per-HC memory pools (could be per-bus, but ...) */
        struct dma_pool         *qh_pool;       /* qh per active urb */
        struct dma_pool         *qtd_pool;      /* one or more per qh */
        struct dma_pool         *itd_pool;      /* itd per iso urb */
        struct dma_pool         *sitd_pool;     /* sitd per split iso urb */

        unsigned                random_frame;
        unsigned long           next_statechange;
        ktime_t                 last_periodic_enable;
        u32                     command;

        /* SILICON QUIRKS */
        unsigned                no_selective_suspend:1;
        unsigned                has_fsl_port_bug:1; /* FreeScale */
        unsigned                has_fsl_hs_errata:1;    /* Freescale HS quirk */
        unsigned                big_endian_mmio:1;
        unsigned                big_endian_desc:1;
        unsigned                big_endian_capbase:1;
        unsigned                has_amcc_usb23:1;
        unsigned                need_io_watchdog:1;
        unsigned                amd_pll_fix:1;
        unsigned                use_dummy_qh:1; /* AMD Frame List table quirk*/
        unsigned                has_synopsys_hc_bug:1; /* Synopsys HC */
        unsigned                frame_index_bug:1; /* MosChip (AKA NetMos) */
        unsigned                need_oc_pp_cycle:1; /* MPC834X port power */
        unsigned                imx28_write_fix:1; /* For Freescale i.MX28 */

        /* required for usb32 quirk */
        #define OHCI_CTRL_HCFS          (3 << 6)
        #define OHCI_USB_OPER           (2 << 6)
        #define OHCI_USB_SUSPEND        (3 << 6)

        #define OHCI_HCCTRL_OFFSET      0x4
        #define OHCI_HCCTRL_LEN         0x4
        __hc32                  *ohci_hcctrl_reg;
        unsigned                has_hostpc:1;
        unsigned                has_tdi_phy_lpm:1;
        unsigned                has_ppcd:1; /* support per-port change bits */
        u8                      sbrn;           /* packed release number */

        /* irq statistics */
#ifdef EHCI_STATS
        struct ehci_stats       stats;
#       define COUNT(x) do { (x)++; } while (0)
#else
#       define COUNT(x) do {} while (0)
#endif

        /* debug files */
#ifdef CONFIG_DYNAMIC_DEBUG
        struct dentry           *debug_dir;
#endif

        /* bandwidth usage */
#define EHCI_BANDWIDTH_SIZE     64
#define EHCI_BANDWIDTH_FRAMES   (EHCI_BANDWIDTH_SIZE >> 3)
        u8                      bandwidth[EHCI_BANDWIDTH_SIZE];
                                                /* us allocated per uframe */
        u8                      tt_budget[EHCI_BANDWIDTH_SIZE];
                                                /* us budgeted per uframe */
        struct list_head        tt_list;

        /* platform-specific data -- must come last */
        unsigned long           priv[0] __aligned(sizeof(s64));
};

/* convert between an HCD pointer and the corresponding EHCI_HCD */
static inline struct ehci_hcd *hcd_to_ehci (struct usb_hcd *hcd)
{
        return (struct ehci_hcd *) (hcd->hcd_priv);
}
static inline struct usb_hcd *ehci_to_hcd (struct ehci_hcd *ehci)
{
        return container_of ((void *) ehci, struct usb_hcd, hcd_priv);
}

/*-------------------------------------------------------------------------*/

#include <linux/usb/ehci_def.h>

/*-------------------------------------------------------------------------*/

#define QTD_NEXT(ehci, dma)     cpu_to_hc32(ehci, (u32)dma)

/*
 * EHCI Specification 0.95 Section 3.5
 * QTD: describe data transfer components (buffer, direction, ...)
 * See Fig 3-6 "Queue Element Transfer Descriptor Block Diagram".
 *
 * These are associated only with "QH" (Queue Head) structures,
 * used with control, bulk, and interrupt transfers.
 */
struct ehci_qtd {
        /* first part defined by EHCI spec */
        __hc32                  hw_next;        /* see EHCI 3.5.1 */
        __hc32                  hw_alt_next;    /* see EHCI 3.5.2 */
        __hc32                  hw_token;       /* see EHCI 3.5.3 */
#define QTD_TOGGLE      (1 << 31)       /* data toggle */
#define QTD_LENGTH(tok) (((tok)>>16) & 0x7fff)
#define QTD_IOC         (1 << 15)       /* interrupt on complete */
#define QTD_CERR(tok)   (((tok)>>10) & 0x3)
#define QTD_PID(tok)    (((tok)>>8) & 0x3)
#define QTD_STS_ACTIVE  (1 << 7)        /* HC may execute this */
#define QTD_STS_HALT    (1 << 6)        /* halted on error */
#define QTD_STS_DBE     (1 << 5)        /* data buffer error (in HC) */
#define QTD_STS_BABBLE  (1 << 4)        /* device was babbling (qtd halted) */
#define QTD_STS_XACT    (1 << 3)        /* device gave illegal response */
#define QTD_STS_MMF     (1 << 2)        /* incomplete split transaction */
#define QTD_STS_STS     (1 << 1)        /* split transaction state */
#define QTD_STS_PING    (1 << 0)        /* issue PING? */

#define ACTIVE_BIT(ehci)        cpu_to_hc32(ehci, QTD_STS_ACTIVE)
#define HALT_BIT(ehci)          cpu_to_hc32(ehci, QTD_STS_HALT)
#define STATUS_BIT(ehci)        cpu_to_hc32(ehci, QTD_STS_STS)

        __hc32                  hw_buf [5];        /* see EHCI 3.5.4 */
        __hc32                  hw_buf_hi [5];        /* Appendix B */

        /* the rest is HCD-private */
        dma_addr_t              qtd_dma;                /* qtd address */
        struct list_head        qtd_list;               /* sw qtd list */
        struct urb              *urb;                   /* qtd's urb */
        size_t                  length;                 /* length of buffer */
} __attribute__ ((aligned (32)));

/* mask NakCnt+T in qh->hw_alt_next */
#define QTD_MASK(ehci)  cpu_to_hc32 (ehci, ~0x1f)

#define IS_SHORT_READ(token) (QTD_LENGTH (token) != 0 && QTD_PID (token) == 1)

/*-------------------------------------------------------------------------*/

/* type tag from {qh,itd,sitd,fstn}->hw_next */
#define Q_NEXT_TYPE(ehci,dma)   ((dma) & cpu_to_hc32(ehci, 3 << 1))

/*
 * Now the following defines are not converted using the
 * cpu_to_le32() macro anymore, since we have to support
 * "dynamic" switching between be and le support, so that the driver
 * can be used on one system with SoC EHCI controller using big-endian
 * descriptors as well as a normal little-endian PCI EHCI controller.
 */
/* values for that type tag */
#define Q_TYPE_ITD      (0 << 1)
#define Q_TYPE_QH       (1 << 1)
#define Q_TYPE_SITD     (2 << 1)
#define Q_TYPE_FSTN     (3 << 1)

/* next async queue entry, or pointer to interrupt/periodic QH */
#define QH_NEXT(ehci,dma)       (cpu_to_hc32(ehci, (((u32)dma)&~0x01f)|Q_TYPE_QH))

/* for periodic/async schedules and qtd lists, mark end of list */
#define EHCI_LIST_END(ehci)     cpu_to_hc32(ehci, 1) /* "null pointer" to hw */

/*
 * Entries in periodic shadow table are pointers to one of four kinds
 * of data structure.  That's dictated by the hardware; a type tag is
 * encoded in the low bits of the hardware's periodic schedule.  Use
 * Q_NEXT_TYPE to get the tag.
 *
 * For entries in the async schedule, the type tag always says "qh".
 */
union ehci_shadow {
        struct ehci_qh          *qh;            /* Q_TYPE_QH */
        struct ehci_itd         *itd;           /* Q_TYPE_ITD */
        struct ehci_sitd        *sitd;          /* Q_TYPE_SITD */
        struct ehci_fstn        *fstn;          /* Q_TYPE_FSTN */
        __hc32                  *hw_next;       /* (all types) */
        void                    *ptr;
};

/*-------------------------------------------------------------------------*/

/*
 * EHCI Specification 0.95 Section 3.6
 * QH: describes control/bulk/interrupt endpoints
 * See Fig 3-7 "Queue Head Structure Layout".
 *
 * These appear in both the async and (for interrupt) periodic schedules.
 */

/* first part defined by EHCI spec */
struct ehci_qh_hw {
        __hc32                  hw_next;        /* see EHCI 3.6.1 */
        __hc32                  hw_info1;       /* see EHCI 3.6.2 */
#define QH_CONTROL_EP   (1 << 27)       /* FS/LS control endpoint */
#define QH_HEAD         (1 << 15)       /* Head of async reclamation list */
#define QH_TOGGLE_CTL   (1 << 14)       /* Data toggle control */
#define QH_HIGH_SPEED   (2 << 12)       /* Endpoint speed */
#define QH_LOW_SPEED    (1 << 12)
#define QH_FULL_SPEED   (0 << 12)
#define QH_INACTIVATE   (1 << 7)        /* Inactivate on next transaction */
        __hc32                  hw_info2;        /* see EHCI 3.6.2 */
#define QH_SMASK        0x000000ff
#define QH_CMASK        0x0000ff00
#define QH_HUBADDR      0x007f0000
#define QH_HUBPORT      0x3f800000
#define QH_MULT         0xc0000000
        __hc32                  hw_current;     /* qtd list - see EHCI 3.6.4 */

        /* qtd overlay (hardware parts of a struct ehci_qtd) */
        __hc32                  hw_qtd_next;
        __hc32                  hw_alt_next;
        __hc32                  hw_token;
        __hc32                  hw_buf [5];
        __hc32                  hw_buf_hi [5];
} __attribute__ ((aligned(32)));

struct ehci_qh {
        struct ehci_qh_hw       *hw;            /* Must come first */
        /* the rest is HCD-private */
        dma_addr_t              qh_dma;         /* address of qh */
        union ehci_shadow       qh_next;        /* ptr to qh; or periodic */
        struct list_head        qtd_list;       /* sw qtd list */
        struct list_head        intr_node;      /* list of intr QHs */
        struct ehci_qtd         *dummy;
        struct list_head        unlink_node;
        struct ehci_per_sched   ps;             /* scheduling info */

        unsigned                unlink_cycle;

        u8                      qh_state;
#define QH_STATE_LINKED         1               /* HC sees this */
#define QH_STATE_UNLINK         2               /* HC may still see this */
#define QH_STATE_IDLE           3               /* HC doesn't see this */
#define QH_STATE_UNLINK_WAIT    4               /* LINKED and on unlink q */
#define QH_STATE_COMPLETING     5               /* don't touch token.HALT */

        u8                      xacterrs;       /* XactErr retry counter */
#define QH_XACTERR_MAX          32              /* XactErr retry limit */

        u8                      gap_uf;         /* uframes split/csplit gap */

        unsigned                is_out:1;       /* bulk or intr OUT */
        unsigned                clearing_tt:1;  /* Clear-TT-Buf in progress */
        unsigned                dequeue_during_giveback:1;
        unsigned                exception:1;    /* got a fault, or an unlink
                                                   was requested */
};

/*-------------------------------------------------------------------------*/

/* description of one iso transaction (up to 3 KB data if highspeed) */
struct ehci_iso_packet {
        /* These will be copied to iTD when scheduling */
        u64                     bufp;           /* itd->hw_bufp{,_hi}[pg] |= */
        __hc32                  transaction;    /* itd->hw_transaction[i] |= */
        u8                      cross;          /* buf crosses pages */
        /* for full speed OUT splits */
        u32                     buf1;
};

/* temporary schedule data for packets from iso urbs (both speeds)
 * each packet is one logical usb transaction to the device (not TT),
 * beginning at stream->next_uframe
 */
struct ehci_iso_sched {
        struct list_head        td_list;
        unsigned                span;
        unsigned                first_packet;
        struct ehci_iso_packet  packet [0];
};

/*
 * ehci_iso_stream - groups all (s)itds for this endpoint.
 * acts like a qh would, if EHCI had them for ISO.
 */
struct ehci_iso_stream {
        /* first field matches ehci_hq, but is NULL */
        struct ehci_qh_hw       *hw;

        u8                      bEndpointAddress;
        u8                      highspeed;
        struct list_head        td_list;        /* queued itds/sitds */
        struct list_head        free_list;      /* list of unused itds/sitds */

        /* output of (re)scheduling */
        struct ehci_per_sched   ps;             /* scheduling info */
        unsigned                next_uframe;
        __hc32                  splits;

        /* the rest is derived from the endpoint descriptor,
         * including the extra info for hw_bufp[0..2]
         */
        u16                     uperiod;        /* period in uframes */
        u16                     maxp;
        unsigned                bandwidth;

        /* This is used to initialize iTD's hw_bufp fields */
        __hc32                  buf0;
        __hc32                  buf1;
        __hc32                  buf2;

        /* this is used to initialize sITD's tt info */
        __hc32                  address;
};

/*-------------------------------------------------------------------------*/

/*
 * EHCI Specification 0.95 Section 3.3
 * Fig 3-4 "Isochronous Transaction Descriptor (iTD)"
 *
 * Schedule records for high speed iso xfers
 */
struct ehci_itd {
        /* first part defined by EHCI spec */
        __hc32                  hw_next;           /* see EHCI 3.3.1 */
        __hc32                  hw_transaction [8]; /* see EHCI 3.3.2 */
#define EHCI_ISOC_ACTIVE        (1<<31)        /* activate transfer this slot */
#define EHCI_ISOC_BUF_ERR       (1<<30)        /* Data buffer error */
#define EHCI_ISOC_BABBLE        (1<<29)        /* babble detected */
#define EHCI_ISOC_XACTERR       (1<<28)        /* XactErr - transaction error */
#define EHCI_ITD_LENGTH(tok)    (((tok)>>16) & 0x0fff)
#define EHCI_ITD_IOC            (1 << 15)       /* interrupt on complete */

#define ITD_ACTIVE(ehci)        cpu_to_hc32(ehci, EHCI_ISOC_ACTIVE)

        __hc32                  hw_bufp [7];    /* see EHCI 3.3.3 */
        __hc32                  hw_bufp_hi [7]; /* Appendix B */

        /* the rest is HCD-private */
        dma_addr_t              itd_dma;        /* for this itd */
        union ehci_shadow       itd_next;       /* ptr to periodic q entry */

        struct urb              *urb;
        struct ehci_iso_stream  *stream;        /* endpoint's queue */
        struct list_head        itd_list;       /* list of stream's itds */

        /* any/all hw_transactions here may be used by that urb */
        unsigned                frame;          /* where scheduled */
        unsigned                pg;
        unsigned                index[8];       /* in urb->iso_frame_desc */
} __attribute__ ((aligned (32)));

/*-------------------------------------------------------------------------*/

/*
 * EHCI Specification 0.95 Section 3.4
 * siTD, aka split-transaction isochronous Transfer Descriptor
 *       ... describe full speed iso xfers through TT in hubs
 * see Figure 3-5 "Split-transaction Isochronous Transaction Descriptor (siTD)
 */
struct ehci_sitd {
        /* first part defined by EHCI spec */
        __hc32                  hw_next;
/* uses bit field macros above - see EHCI 0.95 Table 3-8 */
        __hc32                  hw_fullspeed_ep;        /* EHCI table 3-9 */
        __hc32                  hw_uframe;              /* EHCI table 3-10 */
        __hc32                  hw_results;             /* EHCI table 3-11 */
#define SITD_IOC        (1 << 31)       /* interrupt on completion */
#define SITD_PAGE       (1 << 30)       /* buffer 0/1 */
#define SITD_LENGTH(x)  (0x3ff & ((x)>>16))
#define SITD_STS_ACTIVE (1 << 7)        /* HC may execute this */
#define SITD_STS_ERR    (1 << 6)        /* error from TT */
#define SITD_STS_DBE    (1 << 5)        /* data buffer error (in HC) */
#define SITD_STS_BABBLE (1 << 4)        /* device was babbling */
#define SITD_STS_XACT   (1 << 3)        /* illegal IN response */
#define SITD_STS_MMF    (1 << 2)        /* incomplete split transaction */
#define SITD_STS_STS    (1 << 1)        /* split transaction state */

#define SITD_ACTIVE(ehci)       cpu_to_hc32(ehci, SITD_STS_ACTIVE)

        __hc32                  hw_buf [2];             /* EHCI table 3-12 */
        __hc32                  hw_backpointer;         /* EHCI table 3-13 */
        __hc32                  hw_buf_hi [2];          /* Appendix B */

        /* the rest is HCD-private */
        dma_addr_t              sitd_dma;
        union ehci_shadow       sitd_next;      /* ptr to periodic q entry */

        struct urb              *urb;
        struct ehci_iso_stream  *stream;        /* endpoint's queue */
        struct list_head        sitd_list;      /* list of stream's sitds */
        unsigned                frame;
        unsigned                index;
} __attribute__ ((aligned (32)));

/*-------------------------------------------------------------------------*/

/*
 * EHCI Specification 0.96 Section 3.7
 * Periodic Frame Span Traversal Node (FSTN)
 *
 * Manages split interrupt transactions (using TT) that span frame boundaries
 * into uframes 0/1; see 4.12.2.2.  In those uframes, a "save place" FSTN
 * makes the HC jump (back) to a QH to scan for fs/ls QH completions until
 * it hits a "restore" FSTN; then it returns to finish other uframe 0/1 work.
 */
struct ehci_fstn {
        __hc32                  hw_next;        /* any periodic q entry */
        __hc32                  hw_prev;        /* qh or EHCI_LIST_END */

        /* the rest is HCD-private */
        dma_addr_t              fstn_dma;
        union ehci_shadow       fstn_next;      /* ptr to periodic q entry */
} __attribute__ ((aligned (32)));

/*-------------------------------------------------------------------------*/

/*
 * USB-2.0 Specification Sections 11.14 and 11.18
 * Scheduling and budgeting split transactions using TTs
 *
 * A hub can have a single TT for all its ports, or multiple TTs (one for each
 * port).  The bandwidth and budgeting information for the full/low-speed bus
 * below each TT is self-contained and independent of the other TTs or the
 * high-speed bus.
 *
 * "Bandwidth" refers to the number of microseconds on the FS/LS bus allocated
 * to an interrupt or isochronous endpoint for each frame.  "Budget" refers to
 * the best-case estimate of the number of full-speed bytes allocated to an
 * endpoint for each microframe within an allocated frame.
 *
 * Removal of an endpoint invalidates a TT's budget.  Instead of trying to
 * keep an up-to-date record, we recompute the budget when it is needed.
 */

struct ehci_tt {
        u16                     bandwidth[EHCI_BANDWIDTH_FRAMES];

        struct list_head        tt_list;        /* List of all ehci_tt's */
        struct list_head        ps_list;        /* Items using this TT */
        struct usb_tt           *usb_tt;
        int                     tt_port;        /* TT port number */
};

/*-------------------------------------------------------------------------*/

/* Prepare the PORTSC wakeup flags during controller suspend/resume */

#define ehci_prepare_ports_for_controller_suspend(ehci, do_wakeup)      \
                ehci_adjust_port_wakeup_flags(ehci, true, do_wakeup);

#define ehci_prepare_ports_for_controller_resume(ehci)                  \
                ehci_adjust_port_wakeup_flags(ehci, false, false);

/*-------------------------------------------------------------------------*/

#ifdef CONFIG_USB_EHCI_ROOT_HUB_TT

/*
 * Some EHCI controllers have a Transaction Translator built into the
 * root hub. This is a non-standard feature.  Each controller will need
 * to add code to the following inline functions, and call them as
 * needed (mostly in root hub code).
 */

#define ehci_is_TDI(e)                  (ehci_to_hcd(e)->has_tt)

/* Returns the speed of a device attached to a port on the root hub. */
static inline unsigned int
ehci_port_speed(struct ehci_hcd *ehci, unsigned int portsc)
{
        if (ehci_is_TDI(ehci)) {
                switch ((portsc >> (ehci->has_hostpc ? 25 : 26)) & 3) {
                case 0:
                        return 0;
                case 1:
                        return USB_PORT_STAT_LOW_SPEED;
                case 2:
                default:
                        return USB_PORT_STAT_HIGH_SPEED;
                }
        }
        return USB_PORT_STAT_HIGH_SPEED;
}

#else

#define ehci_is_TDI(e)                  (0)

#define ehci_port_speed(ehci, portsc)   USB_PORT_STAT_HIGH_SPEED
#endif

/*-------------------------------------------------------------------------*/

#ifdef CONFIG_PPC_83xx
/* Some Freescale processors have an erratum in which the TT
 * port number in the queue head was 0..N-1 instead of 1..N.
 */
#define ehci_has_fsl_portno_bug(e)              ((e)->has_fsl_port_bug)
#else
#define ehci_has_fsl_portno_bug(e)              (0)
#endif

#define PORTSC_FSL_PFSC 24      /* Port Force Full-Speed Connect */

#if defined(CONFIG_PPC_85xx)
/* Some Freescale processors have an erratum (USB A-005275) in which
 * incoming packets get corrupted in HS mode
 */
#define ehci_has_fsl_hs_errata(e)       ((e)->has_fsl_hs_errata)
#else
#define ehci_has_fsl_hs_errata(e)       (0)
#endif

/*
 * While most USB host controllers implement their registers in
 * little-endian format, a minority (celleb companion chip) implement
 * them in big endian format.
 *
 * This attempts to support either format at compile time without a
 * runtime penalty, or both formats with the additional overhead
 * of checking a flag bit.
 *
 * ehci_big_endian_capbase is a special quirk for controllers that
 * implement the HC capability registers as separate registers and not
 * as fields of a 32-bit register.
 */

#ifdef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
#define ehci_big_endian_mmio(e)         ((e)->big_endian_mmio)
#define ehci_big_endian_capbase(e)      ((e)->big_endian_capbase)
#else
#define ehci_big_endian_mmio(e)         0
#define ehci_big_endian_capbase(e)      0
#endif

/*
 * Big-endian read/write functions are arch-specific.
 * Other arches can be added if/when they're needed.
 */
#if defined(CONFIG_ARM) && defined(CONFIG_ARCH_IXP4XX)
#define readl_be(addr)          __raw_readl((__force unsigned *)addr)
#define writel_be(val, addr)    __raw_writel(val, (__force unsigned *)addr)
#endif

static inline unsigned int ehci_readl(const struct ehci_hcd *ehci,
                __u32 __iomem * regs)
{
#ifdef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
        return ehci_big_endian_mmio(ehci) ?
                readl_be(regs) :
                readl(regs);
#else
        return readl(regs);
#endif
}

#ifdef CONFIG_SOC_IMX28
static inline void imx28_ehci_writel(const unsigned int val,
                volatile __u32 __iomem *addr)
{
        __asm__ ("swp %0, %0, [%1]" : : "r"(val), "r"(addr));
}
#else
static inline void imx28_ehci_writel(const unsigned int val,
                volatile __u32 __iomem *addr)
{
}
#endif
static inline void ehci_writel(const struct ehci_hcd *ehci,
                const unsigned int val, __u32 __iomem *regs)
{
#ifdef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
        ehci_big_endian_mmio(ehci) ?
                writel_be(val, regs) :
                writel(val, regs);
#else
        if (ehci->imx28_write_fix)
                imx28_ehci_writel(val, regs);
        else
                writel(val, regs);
#endif
}

/*
 * On certain ppc-44x SoC there is a HW issue, that could only worked around with
 * explicit suspend/operate of OHCI. This function hereby makes sense only on that arch.
 * Other common bits are dependent on has_amcc_usb23 quirk flag.
 */
#ifdef CONFIG_44x
static inline void set_ohci_hcfs(struct ehci_hcd *ehci, int operational)
{
        u32 hc_control;

        hc_control = (readl_be(ehci->ohci_hcctrl_reg) & ~OHCI_CTRL_HCFS);
        if (operational)
                hc_control |= OHCI_USB_OPER;
        else
                hc_control |= OHCI_USB_SUSPEND;

        writel_be(hc_control, ehci->ohci_hcctrl_reg);
        (void) readl_be(ehci->ohci_hcctrl_reg);
}
#else
static inline void set_ohci_hcfs(struct ehci_hcd *ehci, int operational)
{ }
#endif

/*-------------------------------------------------------------------------*/

/*
 * The AMCC 440EPx not only implements its EHCI registers in big-endian
 * format, but also its DMA data structures (descriptors).
 *
 * EHCI controllers accessed through PCI work normally (little-endian
 * everywhere), so we won't bother supporting a BE-only mode for now.
 */
#ifdef CONFIG_USB_EHCI_BIG_ENDIAN_DESC
#define ehci_big_endian_desc(e)         ((e)->big_endian_desc)

/* cpu to ehci */
static inline __hc32 cpu_to_hc32 (const struct ehci_hcd *ehci, const u32 x)
{
        return ehci_big_endian_desc(ehci)
                ? (__force __hc32)cpu_to_be32(x)
                : (__force __hc32)cpu_to_le32(x);
}

/* ehci to cpu */
static inline u32 hc32_to_cpu (const struct ehci_hcd *ehci, const __hc32 x)
{
        return ehci_big_endian_desc(ehci)
                ? be32_to_cpu((__force __be32)x)
                : le32_to_cpu((__force __le32)x);
}

static inline u32 hc32_to_cpup (const struct ehci_hcd *ehci, const __hc32 *x)
{
        return ehci_big_endian_desc(ehci)
                ? be32_to_cpup((__force __be32 *)x)
                : le32_to_cpup((__force __le32 *)x);
}

#else

/* cpu to ehci */
static inline __hc32 cpu_to_hc32 (const struct ehci_hcd *ehci, const u32 x)
{
        return cpu_to_le32(x);
}

/* ehci to cpu */
static inline u32 hc32_to_cpu (const struct ehci_hcd *ehci, const __hc32 x)
{
        return le32_to_cpu(x);
}

static inline u32 hc32_to_cpup (const struct ehci_hcd *ehci, const __hc32 *x)
{
        return le32_to_cpup(x);
}

#endif

/*-------------------------------------------------------------------------*/

#define ehci_dbg(ehci, fmt, args...) \
        dev_dbg(ehci_to_hcd(ehci)->self.controller , fmt , ## args)
#define ehci_err(ehci, fmt, args...) \
        dev_err(ehci_to_hcd(ehci)->self.controller , fmt , ## args)
#define ehci_info(ehci, fmt, args...) \
        dev_info(ehci_to_hcd(ehci)->self.controller , fmt , ## args)
#define ehci_warn(ehci, fmt, args...) \
        dev_warn(ehci_to_hcd(ehci)->self.controller , fmt , ## args)


#ifndef CONFIG_DYNAMIC_DEBUG
#define STUB_DEBUG_FILES
#endif

/*-------------------------------------------------------------------------*/

/* Declarations of things exported for use by ehci platform drivers */

struct ehci_driver_overrides {
        size_t          extra_priv_size;
        int             (*reset)(struct usb_hcd *hcd);
        int             (*port_power)(struct usb_hcd *hcd,
                                int portnum, bool enable);
};

extern void     ehci_init_driver(struct hc_driver *drv,
                                const struct ehci_driver_overrides *over);
extern int      ehci_setup(struct usb_hcd *hcd);
extern int      ehci_handshake(struct ehci_hcd *ehci, void __iomem *ptr,
                                u32 mask, u32 done, int usec);
extern int      ehci_reset(struct ehci_hcd *ehci);

#ifdef CONFIG_PM
extern int      ehci_suspend(struct usb_hcd *hcd, bool do_wakeup);
extern int      ehci_resume(struct usb_hcd *hcd, bool force_reset);
extern void     ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
                        bool suspending, bool do_wakeup);
#endif  /* CONFIG_PM */

extern int      ehci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
                                 u16 wIndex, char *buf, u16 wLength);

#endif /* __LINUX_EHCI_HCD_H */