x86: Make the vdso2c compiler use the host architecture headers
[linux/fpc-iii.git] / arch / arm / boot / dts / ste-hrefprev60.dtsi
blobece222d51717c294385fd2edc8960b1ebd6f471b
1 /*
2  * Copyright 2012 ST-Ericsson AB
3  *
4  * The code contained herein is licensed under the GNU General Public
5  * License. You may obtain a copy of the GNU General Public License
6  * Version 2 or later at the following locations:
7  *
8  * http://www.opensource.org/licenses/gpl-license.html
9  * http://www.gnu.org/copyleft/gpl.html
10  *
11  * Device Tree for the HREF+ prior to the v60 variant.
12  */
14 #include "ste-dbx5x0.dtsi"
15 #include "ste-href-ab8500.dtsi"
16 #include "ste-href.dtsi"
18 / {
19         gpio_keys {
20                 button@1 {
21                         gpios = <&tc3589x_gpio 7 GPIO_ACTIVE_HIGH>;
22                 };
23         };
25         soc {
26                 /* Enable UART1 on this board */
27                 uart@80121000 {
28                         status = "okay";
29                 };
31                 i2c@80004000 {
32                         tps61052@33 {
33                                 compatible = "tps61052";
34                                 reg = <0x33>;
35                         };
37                         tc35892@42 {
38                                 compatible = "toshiba,tc35892";
39                                 reg = <0x42>;
40                                 interrupt-parent = <&gpio6>;
41                                 interrupts = <25 IRQ_TYPE_EDGE_RISING>;
42                                 pinctrl-names = "default";
43                                 pinctrl-0 = <&tc35892_hrefprev60_mode>;
45                                 interrupt-controller;
46                                 #interrupt-cells = <1>;
48                                 tc3589x_gpio: tc3589x_gpio {
49                                         compatible = "tc3589x-gpio";
50                                         interrupts = <0>;
52                                         interrupt-controller;
53                                         #interrupt-cells = <2>;
54                                         gpio-controller;
55                                         #gpio-cells = <2>;
56                                 };
57                         };
58                 };
60                 ssp@80002000 {
61                         /*
62                          * On the first generation boards, this SSP/SPI port was connected
63                          * to the AB8500.
64                          */
65                         pinctrl-names = "default";
66                         pinctrl-0 = <&ssp0_hrefprev60_mode>;
67                 };
69                 // External Micro SD slot
70                 sdi0_per1@80126000 {
71                         cd-gpios  = <&tc3589x_gpio 3 GPIO_ACTIVE_HIGH>;
72                 };
74                 vmmci: regulator-gpio {
75                         gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
76                         enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
77                 };
79                 pinctrl {
80                         /* Set this up using hogs */
81                         pinctrl-names = "default";
82                         pinctrl-0 = <&ipgpio_hrefprev60_mode>;
84                         ssp0 {
85                                 ssp0_hrefprev60_mode: ssp0_hrefprev60_default {
86                                         hrefprev60_mux {
87                                                 function = "ssp0";
88                                                 groups = "ssp0_a_1";
89                                         };
90                                         hrefprev60_cfg1 {
91                                                 pins = "GPIO145_C13"; /* RXD */
92                                                 ste,config = <&in_pd>;
93                                         };
95                                 };
96                         };
97                         sdi0 {
98                                 /* This additional pin needed on early MOP500 and HREFs previous to v60 */
99                                 sdi0_default_mode: sdi0_default {
100                                         hrefprev60_mux {
101                                                 function = "mc0";
102                                                 groups = "mc0dat31dir_a_1";
103                                         };
104                                         hrefprev60_cfg1 {
105                                                 pins = "GPIO21_AB3"; /* DAT31DIR */
106                                                 ste,config = <&out_hi>;
107                                         };
109                                 };
110                         };
111                         tc35892 {
112                                 tc35892_hrefprev60_mode: tc35892_hrefprev60 {
113                                         hrefprev60_cfg {
114                                                 pins = "GPIO217_AH12";
115                                                 ste,config = <&gpio_in_pu>;
116                                         };
117                                 };
118                         };
119                         ipgpio {
120                                  ipgpio_hrefprev60_mode: ipgpio_hrefprev60 {
121                                         hrefprev60_mux {
122                                                 function = "ipgpio";
123                                                 groups = "ipgpio0_c_1", "ipgpio1_c_1";
124                                         };
125                                         hrefprev60_cfg1 {
126                                                 pins = "GPIO6_AF6", "GPIO7_AG5";
127                                                 ste,config = <&in_pu>;
128                                         };
129                                  };
130                         };
131                 };
132         };