gro: Allow tunnel stacking in the case of FOU/GUE
[linux/fpc-iii.git] / drivers / clocksource / sh_cmt.c
blobb8ff3c64cc452a16fc4108426fb6e5b1c54e91e8
1 /*
2 * SuperH Timer Support - CMT
4 * Copyright (C) 2008 Magnus Damm
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License
10 * This program is distributed in the hope that it will be useful,
11 * but WITHOUT ANY WARRANTY; without even the implied warranty of
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 * GNU General Public License for more details.
16 #include <linux/clk.h>
17 #include <linux/clockchips.h>
18 #include <linux/clocksource.h>
19 #include <linux/delay.h>
20 #include <linux/err.h>
21 #include <linux/init.h>
22 #include <linux/interrupt.h>
23 #include <linux/io.h>
24 #include <linux/ioport.h>
25 #include <linux/irq.h>
26 #include <linux/module.h>
27 #include <linux/of.h>
28 #include <linux/platform_device.h>
29 #include <linux/pm_domain.h>
30 #include <linux/pm_runtime.h>
31 #include <linux/sh_timer.h>
32 #include <linux/slab.h>
33 #include <linux/spinlock.h>
35 struct sh_cmt_device;
38 * The CMT comes in 5 different identified flavours, depending not only on the
39 * SoC but also on the particular instance. The following table lists the main
40 * characteristics of those flavours.
42 * 16B 32B 32B-F 48B 48B-2
43 * -----------------------------------------------------------------------------
44 * Channels 2 1/4 1 6 2/8
45 * Control Width 16 16 16 16 32
46 * Counter Width 16 32 32 32/48 32/48
47 * Shared Start/Stop Y Y Y Y N
49 * The 48-bit gen2 version has a per-channel start/stop register located in the
50 * channel registers block. All other versions have a shared start/stop register
51 * located in the global space.
53 * Channels are indexed from 0 to N-1 in the documentation. The channel index
54 * infers the start/stop bit position in the control register and the channel
55 * registers block address. Some CMT instances have a subset of channels
56 * available, in which case the index in the documentation doesn't match the
57 * "real" index as implemented in hardware. This is for instance the case with
58 * CMT0 on r8a7740, which is a 32-bit variant with a single channel numbered 0
59 * in the documentation but using start/stop bit 5 and having its registers
60 * block at 0x60.
62 * Similarly CMT0 on r8a73a4, r8a7790 and r8a7791, while implementing 32-bit
63 * channels only, is a 48-bit gen2 CMT with the 48-bit channels unavailable.
66 enum sh_cmt_model {
67 SH_CMT_16BIT,
68 SH_CMT_32BIT,
69 SH_CMT_32BIT_FAST,
70 SH_CMT_48BIT,
71 SH_CMT_48BIT_GEN2,
74 struct sh_cmt_info {
75 enum sh_cmt_model model;
77 unsigned long width; /* 16 or 32 bit version of hardware block */
78 unsigned long overflow_bit;
79 unsigned long clear_bits;
81 /* callbacks for CMSTR and CMCSR access */
82 unsigned long (*read_control)(void __iomem *base, unsigned long offs);
83 void (*write_control)(void __iomem *base, unsigned long offs,
84 unsigned long value);
86 /* callbacks for CMCNT and CMCOR access */
87 unsigned long (*read_count)(void __iomem *base, unsigned long offs);
88 void (*write_count)(void __iomem *base, unsigned long offs,
89 unsigned long value);
92 struct sh_cmt_channel {
93 struct sh_cmt_device *cmt;
95 unsigned int index; /* Index in the documentation */
96 unsigned int hwidx; /* Real hardware index */
98 void __iomem *iostart;
99 void __iomem *ioctrl;
101 unsigned int timer_bit;
102 unsigned long flags;
103 unsigned long match_value;
104 unsigned long next_match_value;
105 unsigned long max_match_value;
106 unsigned long rate;
107 raw_spinlock_t lock;
108 struct clock_event_device ced;
109 struct clocksource cs;
110 unsigned long total_cycles;
111 bool cs_enabled;
114 struct sh_cmt_device {
115 struct platform_device *pdev;
117 const struct sh_cmt_info *info;
119 void __iomem *mapbase;
120 struct clk *clk;
122 raw_spinlock_t lock; /* Protect the shared start/stop register */
124 struct sh_cmt_channel *channels;
125 unsigned int num_channels;
126 unsigned int hw_channels;
128 bool has_clockevent;
129 bool has_clocksource;
132 #define SH_CMT16_CMCSR_CMF (1 << 7)
133 #define SH_CMT16_CMCSR_CMIE (1 << 6)
134 #define SH_CMT16_CMCSR_CKS8 (0 << 0)
135 #define SH_CMT16_CMCSR_CKS32 (1 << 0)
136 #define SH_CMT16_CMCSR_CKS128 (2 << 0)
137 #define SH_CMT16_CMCSR_CKS512 (3 << 0)
138 #define SH_CMT16_CMCSR_CKS_MASK (3 << 0)
140 #define SH_CMT32_CMCSR_CMF (1 << 15)
141 #define SH_CMT32_CMCSR_OVF (1 << 14)
142 #define SH_CMT32_CMCSR_WRFLG (1 << 13)
143 #define SH_CMT32_CMCSR_STTF (1 << 12)
144 #define SH_CMT32_CMCSR_STPF (1 << 11)
145 #define SH_CMT32_CMCSR_SSIE (1 << 10)
146 #define SH_CMT32_CMCSR_CMS (1 << 9)
147 #define SH_CMT32_CMCSR_CMM (1 << 8)
148 #define SH_CMT32_CMCSR_CMTOUT_IE (1 << 7)
149 #define SH_CMT32_CMCSR_CMR_NONE (0 << 4)
150 #define SH_CMT32_CMCSR_CMR_DMA (1 << 4)
151 #define SH_CMT32_CMCSR_CMR_IRQ (2 << 4)
152 #define SH_CMT32_CMCSR_CMR_MASK (3 << 4)
153 #define SH_CMT32_CMCSR_DBGIVD (1 << 3)
154 #define SH_CMT32_CMCSR_CKS_RCLK8 (4 << 0)
155 #define SH_CMT32_CMCSR_CKS_RCLK32 (5 << 0)
156 #define SH_CMT32_CMCSR_CKS_RCLK128 (6 << 0)
157 #define SH_CMT32_CMCSR_CKS_RCLK1 (7 << 0)
158 #define SH_CMT32_CMCSR_CKS_MASK (7 << 0)
160 static unsigned long sh_cmt_read16(void __iomem *base, unsigned long offs)
162 return ioread16(base + (offs << 1));
165 static unsigned long sh_cmt_read32(void __iomem *base, unsigned long offs)
167 return ioread32(base + (offs << 2));
170 static void sh_cmt_write16(void __iomem *base, unsigned long offs,
171 unsigned long value)
173 iowrite16(value, base + (offs << 1));
176 static void sh_cmt_write32(void __iomem *base, unsigned long offs,
177 unsigned long value)
179 iowrite32(value, base + (offs << 2));
182 static const struct sh_cmt_info sh_cmt_info[] = {
183 [SH_CMT_16BIT] = {
184 .model = SH_CMT_16BIT,
185 .width = 16,
186 .overflow_bit = SH_CMT16_CMCSR_CMF,
187 .clear_bits = ~SH_CMT16_CMCSR_CMF,
188 .read_control = sh_cmt_read16,
189 .write_control = sh_cmt_write16,
190 .read_count = sh_cmt_read16,
191 .write_count = sh_cmt_write16,
193 [SH_CMT_32BIT] = {
194 .model = SH_CMT_32BIT,
195 .width = 32,
196 .overflow_bit = SH_CMT32_CMCSR_CMF,
197 .clear_bits = ~(SH_CMT32_CMCSR_CMF | SH_CMT32_CMCSR_OVF),
198 .read_control = sh_cmt_read16,
199 .write_control = sh_cmt_write16,
200 .read_count = sh_cmt_read32,
201 .write_count = sh_cmt_write32,
203 [SH_CMT_32BIT_FAST] = {
204 .model = SH_CMT_32BIT_FAST,
205 .width = 32,
206 .overflow_bit = SH_CMT32_CMCSR_CMF,
207 .clear_bits = ~(SH_CMT32_CMCSR_CMF | SH_CMT32_CMCSR_OVF),
208 .read_control = sh_cmt_read16,
209 .write_control = sh_cmt_write16,
210 .read_count = sh_cmt_read32,
211 .write_count = sh_cmt_write32,
213 [SH_CMT_48BIT] = {
214 .model = SH_CMT_48BIT,
215 .width = 32,
216 .overflow_bit = SH_CMT32_CMCSR_CMF,
217 .clear_bits = ~(SH_CMT32_CMCSR_CMF | SH_CMT32_CMCSR_OVF),
218 .read_control = sh_cmt_read32,
219 .write_control = sh_cmt_write32,
220 .read_count = sh_cmt_read32,
221 .write_count = sh_cmt_write32,
223 [SH_CMT_48BIT_GEN2] = {
224 .model = SH_CMT_48BIT_GEN2,
225 .width = 32,
226 .overflow_bit = SH_CMT32_CMCSR_CMF,
227 .clear_bits = ~(SH_CMT32_CMCSR_CMF | SH_CMT32_CMCSR_OVF),
228 .read_control = sh_cmt_read32,
229 .write_control = sh_cmt_write32,
230 .read_count = sh_cmt_read32,
231 .write_count = sh_cmt_write32,
235 #define CMCSR 0 /* channel register */
236 #define CMCNT 1 /* channel register */
237 #define CMCOR 2 /* channel register */
239 static inline unsigned long sh_cmt_read_cmstr(struct sh_cmt_channel *ch)
241 if (ch->iostart)
242 return ch->cmt->info->read_control(ch->iostart, 0);
243 else
244 return ch->cmt->info->read_control(ch->cmt->mapbase, 0);
247 static inline void sh_cmt_write_cmstr(struct sh_cmt_channel *ch,
248 unsigned long value)
250 if (ch->iostart)
251 ch->cmt->info->write_control(ch->iostart, 0, value);
252 else
253 ch->cmt->info->write_control(ch->cmt->mapbase, 0, value);
256 static inline unsigned long sh_cmt_read_cmcsr(struct sh_cmt_channel *ch)
258 return ch->cmt->info->read_control(ch->ioctrl, CMCSR);
261 static inline void sh_cmt_write_cmcsr(struct sh_cmt_channel *ch,
262 unsigned long value)
264 ch->cmt->info->write_control(ch->ioctrl, CMCSR, value);
267 static inline unsigned long sh_cmt_read_cmcnt(struct sh_cmt_channel *ch)
269 return ch->cmt->info->read_count(ch->ioctrl, CMCNT);
272 static inline void sh_cmt_write_cmcnt(struct sh_cmt_channel *ch,
273 unsigned long value)
275 ch->cmt->info->write_count(ch->ioctrl, CMCNT, value);
278 static inline void sh_cmt_write_cmcor(struct sh_cmt_channel *ch,
279 unsigned long value)
281 ch->cmt->info->write_count(ch->ioctrl, CMCOR, value);
284 static unsigned long sh_cmt_get_counter(struct sh_cmt_channel *ch,
285 int *has_wrapped)
287 unsigned long v1, v2, v3;
288 int o1, o2;
290 o1 = sh_cmt_read_cmcsr(ch) & ch->cmt->info->overflow_bit;
292 /* Make sure the timer value is stable. Stolen from acpi_pm.c */
293 do {
294 o2 = o1;
295 v1 = sh_cmt_read_cmcnt(ch);
296 v2 = sh_cmt_read_cmcnt(ch);
297 v3 = sh_cmt_read_cmcnt(ch);
298 o1 = sh_cmt_read_cmcsr(ch) & ch->cmt->info->overflow_bit;
299 } while (unlikely((o1 != o2) || (v1 > v2 && v1 < v3)
300 || (v2 > v3 && v2 < v1) || (v3 > v1 && v3 < v2)));
302 *has_wrapped = o1;
303 return v2;
306 static void sh_cmt_start_stop_ch(struct sh_cmt_channel *ch, int start)
308 unsigned long flags, value;
310 /* start stop register shared by multiple timer channels */
311 raw_spin_lock_irqsave(&ch->cmt->lock, flags);
312 value = sh_cmt_read_cmstr(ch);
314 if (start)
315 value |= 1 << ch->timer_bit;
316 else
317 value &= ~(1 << ch->timer_bit);
319 sh_cmt_write_cmstr(ch, value);
320 raw_spin_unlock_irqrestore(&ch->cmt->lock, flags);
323 static int sh_cmt_enable(struct sh_cmt_channel *ch, unsigned long *rate)
325 int k, ret;
327 pm_runtime_get_sync(&ch->cmt->pdev->dev);
328 dev_pm_syscore_device(&ch->cmt->pdev->dev, true);
330 /* enable clock */
331 ret = clk_enable(ch->cmt->clk);
332 if (ret) {
333 dev_err(&ch->cmt->pdev->dev, "ch%u: cannot enable clock\n",
334 ch->index);
335 goto err0;
338 /* make sure channel is disabled */
339 sh_cmt_start_stop_ch(ch, 0);
341 /* configure channel, periodic mode and maximum timeout */
342 if (ch->cmt->info->width == 16) {
343 *rate = clk_get_rate(ch->cmt->clk) / 512;
344 sh_cmt_write_cmcsr(ch, SH_CMT16_CMCSR_CMIE |
345 SH_CMT16_CMCSR_CKS512);
346 } else {
347 *rate = clk_get_rate(ch->cmt->clk) / 8;
348 sh_cmt_write_cmcsr(ch, SH_CMT32_CMCSR_CMM |
349 SH_CMT32_CMCSR_CMTOUT_IE |
350 SH_CMT32_CMCSR_CMR_IRQ |
351 SH_CMT32_CMCSR_CKS_RCLK8);
354 sh_cmt_write_cmcor(ch, 0xffffffff);
355 sh_cmt_write_cmcnt(ch, 0);
358 * According to the sh73a0 user's manual, as CMCNT can be operated
359 * only by the RCLK (Pseudo 32 KHz), there's one restriction on
360 * modifying CMCNT register; two RCLK cycles are necessary before
361 * this register is either read or any modification of the value
362 * it holds is reflected in the LSI's actual operation.
364 * While at it, we're supposed to clear out the CMCNT as of this
365 * moment, so make sure it's processed properly here. This will
366 * take RCLKx2 at maximum.
368 for (k = 0; k < 100; k++) {
369 if (!sh_cmt_read_cmcnt(ch))
370 break;
371 udelay(1);
374 if (sh_cmt_read_cmcnt(ch)) {
375 dev_err(&ch->cmt->pdev->dev, "ch%u: cannot clear CMCNT\n",
376 ch->index);
377 ret = -ETIMEDOUT;
378 goto err1;
381 /* enable channel */
382 sh_cmt_start_stop_ch(ch, 1);
383 return 0;
384 err1:
385 /* stop clock */
386 clk_disable(ch->cmt->clk);
388 err0:
389 return ret;
392 static void sh_cmt_disable(struct sh_cmt_channel *ch)
394 /* disable channel */
395 sh_cmt_start_stop_ch(ch, 0);
397 /* disable interrupts in CMT block */
398 sh_cmt_write_cmcsr(ch, 0);
400 /* stop clock */
401 clk_disable(ch->cmt->clk);
403 dev_pm_syscore_device(&ch->cmt->pdev->dev, false);
404 pm_runtime_put(&ch->cmt->pdev->dev);
407 /* private flags */
408 #define FLAG_CLOCKEVENT (1 << 0)
409 #define FLAG_CLOCKSOURCE (1 << 1)
410 #define FLAG_REPROGRAM (1 << 2)
411 #define FLAG_SKIPEVENT (1 << 3)
412 #define FLAG_IRQCONTEXT (1 << 4)
414 static void sh_cmt_clock_event_program_verify(struct sh_cmt_channel *ch,
415 int absolute)
417 unsigned long new_match;
418 unsigned long value = ch->next_match_value;
419 unsigned long delay = 0;
420 unsigned long now = 0;
421 int has_wrapped;
423 now = sh_cmt_get_counter(ch, &has_wrapped);
424 ch->flags |= FLAG_REPROGRAM; /* force reprogram */
426 if (has_wrapped) {
427 /* we're competing with the interrupt handler.
428 * -> let the interrupt handler reprogram the timer.
429 * -> interrupt number two handles the event.
431 ch->flags |= FLAG_SKIPEVENT;
432 return;
435 if (absolute)
436 now = 0;
438 do {
439 /* reprogram the timer hardware,
440 * but don't save the new match value yet.
442 new_match = now + value + delay;
443 if (new_match > ch->max_match_value)
444 new_match = ch->max_match_value;
446 sh_cmt_write_cmcor(ch, new_match);
448 now = sh_cmt_get_counter(ch, &has_wrapped);
449 if (has_wrapped && (new_match > ch->match_value)) {
450 /* we are changing to a greater match value,
451 * so this wrap must be caused by the counter
452 * matching the old value.
453 * -> first interrupt reprograms the timer.
454 * -> interrupt number two handles the event.
456 ch->flags |= FLAG_SKIPEVENT;
457 break;
460 if (has_wrapped) {
461 /* we are changing to a smaller match value,
462 * so the wrap must be caused by the counter
463 * matching the new value.
464 * -> save programmed match value.
465 * -> let isr handle the event.
467 ch->match_value = new_match;
468 break;
471 /* be safe: verify hardware settings */
472 if (now < new_match) {
473 /* timer value is below match value, all good.
474 * this makes sure we won't miss any match events.
475 * -> save programmed match value.
476 * -> let isr handle the event.
478 ch->match_value = new_match;
479 break;
482 /* the counter has reached a value greater
483 * than our new match value. and since the
484 * has_wrapped flag isn't set we must have
485 * programmed a too close event.
486 * -> increase delay and retry.
488 if (delay)
489 delay <<= 1;
490 else
491 delay = 1;
493 if (!delay)
494 dev_warn(&ch->cmt->pdev->dev, "ch%u: too long delay\n",
495 ch->index);
497 } while (delay);
500 static void __sh_cmt_set_next(struct sh_cmt_channel *ch, unsigned long delta)
502 if (delta > ch->max_match_value)
503 dev_warn(&ch->cmt->pdev->dev, "ch%u: delta out of range\n",
504 ch->index);
506 ch->next_match_value = delta;
507 sh_cmt_clock_event_program_verify(ch, 0);
510 static void sh_cmt_set_next(struct sh_cmt_channel *ch, unsigned long delta)
512 unsigned long flags;
514 raw_spin_lock_irqsave(&ch->lock, flags);
515 __sh_cmt_set_next(ch, delta);
516 raw_spin_unlock_irqrestore(&ch->lock, flags);
519 static irqreturn_t sh_cmt_interrupt(int irq, void *dev_id)
521 struct sh_cmt_channel *ch = dev_id;
523 /* clear flags */
524 sh_cmt_write_cmcsr(ch, sh_cmt_read_cmcsr(ch) &
525 ch->cmt->info->clear_bits);
527 /* update clock source counter to begin with if enabled
528 * the wrap flag should be cleared by the timer specific
529 * isr before we end up here.
531 if (ch->flags & FLAG_CLOCKSOURCE)
532 ch->total_cycles += ch->match_value + 1;
534 if (!(ch->flags & FLAG_REPROGRAM))
535 ch->next_match_value = ch->max_match_value;
537 ch->flags |= FLAG_IRQCONTEXT;
539 if (ch->flags & FLAG_CLOCKEVENT) {
540 if (!(ch->flags & FLAG_SKIPEVENT)) {
541 if (ch->ced.mode == CLOCK_EVT_MODE_ONESHOT) {
542 ch->next_match_value = ch->max_match_value;
543 ch->flags |= FLAG_REPROGRAM;
546 ch->ced.event_handler(&ch->ced);
550 ch->flags &= ~FLAG_SKIPEVENT;
552 if (ch->flags & FLAG_REPROGRAM) {
553 ch->flags &= ~FLAG_REPROGRAM;
554 sh_cmt_clock_event_program_verify(ch, 1);
556 if (ch->flags & FLAG_CLOCKEVENT)
557 if ((ch->ced.mode == CLOCK_EVT_MODE_SHUTDOWN)
558 || (ch->match_value == ch->next_match_value))
559 ch->flags &= ~FLAG_REPROGRAM;
562 ch->flags &= ~FLAG_IRQCONTEXT;
564 return IRQ_HANDLED;
567 static int sh_cmt_start(struct sh_cmt_channel *ch, unsigned long flag)
569 int ret = 0;
570 unsigned long flags;
572 raw_spin_lock_irqsave(&ch->lock, flags);
574 if (!(ch->flags & (FLAG_CLOCKEVENT | FLAG_CLOCKSOURCE)))
575 ret = sh_cmt_enable(ch, &ch->rate);
577 if (ret)
578 goto out;
579 ch->flags |= flag;
581 /* setup timeout if no clockevent */
582 if ((flag == FLAG_CLOCKSOURCE) && (!(ch->flags & FLAG_CLOCKEVENT)))
583 __sh_cmt_set_next(ch, ch->max_match_value);
584 out:
585 raw_spin_unlock_irqrestore(&ch->lock, flags);
587 return ret;
590 static void sh_cmt_stop(struct sh_cmt_channel *ch, unsigned long flag)
592 unsigned long flags;
593 unsigned long f;
595 raw_spin_lock_irqsave(&ch->lock, flags);
597 f = ch->flags & (FLAG_CLOCKEVENT | FLAG_CLOCKSOURCE);
598 ch->flags &= ~flag;
600 if (f && !(ch->flags & (FLAG_CLOCKEVENT | FLAG_CLOCKSOURCE)))
601 sh_cmt_disable(ch);
603 /* adjust the timeout to maximum if only clocksource left */
604 if ((flag == FLAG_CLOCKEVENT) && (ch->flags & FLAG_CLOCKSOURCE))
605 __sh_cmt_set_next(ch, ch->max_match_value);
607 raw_spin_unlock_irqrestore(&ch->lock, flags);
610 static struct sh_cmt_channel *cs_to_sh_cmt(struct clocksource *cs)
612 return container_of(cs, struct sh_cmt_channel, cs);
615 static cycle_t sh_cmt_clocksource_read(struct clocksource *cs)
617 struct sh_cmt_channel *ch = cs_to_sh_cmt(cs);
618 unsigned long flags, raw;
619 unsigned long value;
620 int has_wrapped;
622 raw_spin_lock_irqsave(&ch->lock, flags);
623 value = ch->total_cycles;
624 raw = sh_cmt_get_counter(ch, &has_wrapped);
626 if (unlikely(has_wrapped))
627 raw += ch->match_value + 1;
628 raw_spin_unlock_irqrestore(&ch->lock, flags);
630 return value + raw;
633 static int sh_cmt_clocksource_enable(struct clocksource *cs)
635 int ret;
636 struct sh_cmt_channel *ch = cs_to_sh_cmt(cs);
638 WARN_ON(ch->cs_enabled);
640 ch->total_cycles = 0;
642 ret = sh_cmt_start(ch, FLAG_CLOCKSOURCE);
643 if (!ret) {
644 __clocksource_update_freq_hz(cs, ch->rate);
645 ch->cs_enabled = true;
647 return ret;
650 static void sh_cmt_clocksource_disable(struct clocksource *cs)
652 struct sh_cmt_channel *ch = cs_to_sh_cmt(cs);
654 WARN_ON(!ch->cs_enabled);
656 sh_cmt_stop(ch, FLAG_CLOCKSOURCE);
657 ch->cs_enabled = false;
660 static void sh_cmt_clocksource_suspend(struct clocksource *cs)
662 struct sh_cmt_channel *ch = cs_to_sh_cmt(cs);
664 sh_cmt_stop(ch, FLAG_CLOCKSOURCE);
665 pm_genpd_syscore_poweroff(&ch->cmt->pdev->dev);
668 static void sh_cmt_clocksource_resume(struct clocksource *cs)
670 struct sh_cmt_channel *ch = cs_to_sh_cmt(cs);
672 pm_genpd_syscore_poweron(&ch->cmt->pdev->dev);
673 sh_cmt_start(ch, FLAG_CLOCKSOURCE);
676 static int sh_cmt_register_clocksource(struct sh_cmt_channel *ch,
677 const char *name)
679 struct clocksource *cs = &ch->cs;
681 cs->name = name;
682 cs->rating = 125;
683 cs->read = sh_cmt_clocksource_read;
684 cs->enable = sh_cmt_clocksource_enable;
685 cs->disable = sh_cmt_clocksource_disable;
686 cs->suspend = sh_cmt_clocksource_suspend;
687 cs->resume = sh_cmt_clocksource_resume;
688 cs->mask = CLOCKSOURCE_MASK(sizeof(unsigned long) * 8);
689 cs->flags = CLOCK_SOURCE_IS_CONTINUOUS;
691 dev_info(&ch->cmt->pdev->dev, "ch%u: used as clock source\n",
692 ch->index);
694 /* Register with dummy 1 Hz value, gets updated in ->enable() */
695 clocksource_register_hz(cs, 1);
696 return 0;
699 static struct sh_cmt_channel *ced_to_sh_cmt(struct clock_event_device *ced)
701 return container_of(ced, struct sh_cmt_channel, ced);
704 static void sh_cmt_clock_event_start(struct sh_cmt_channel *ch, int periodic)
706 struct clock_event_device *ced = &ch->ced;
708 sh_cmt_start(ch, FLAG_CLOCKEVENT);
710 /* TODO: calculate good shift from rate and counter bit width */
712 ced->shift = 32;
713 ced->mult = div_sc(ch->rate, NSEC_PER_SEC, ced->shift);
714 ced->max_delta_ns = clockevent_delta2ns(ch->max_match_value, ced);
715 ced->min_delta_ns = clockevent_delta2ns(0x1f, ced);
717 if (periodic)
718 sh_cmt_set_next(ch, ((ch->rate + HZ/2) / HZ) - 1);
719 else
720 sh_cmt_set_next(ch, ch->max_match_value);
723 static void sh_cmt_clock_event_mode(enum clock_event_mode mode,
724 struct clock_event_device *ced)
726 struct sh_cmt_channel *ch = ced_to_sh_cmt(ced);
728 /* deal with old setting first */
729 switch (ced->mode) {
730 case CLOCK_EVT_MODE_PERIODIC:
731 case CLOCK_EVT_MODE_ONESHOT:
732 sh_cmt_stop(ch, FLAG_CLOCKEVENT);
733 break;
734 default:
735 break;
738 switch (mode) {
739 case CLOCK_EVT_MODE_PERIODIC:
740 dev_info(&ch->cmt->pdev->dev,
741 "ch%u: used for periodic clock events\n", ch->index);
742 sh_cmt_clock_event_start(ch, 1);
743 break;
744 case CLOCK_EVT_MODE_ONESHOT:
745 dev_info(&ch->cmt->pdev->dev,
746 "ch%u: used for oneshot clock events\n", ch->index);
747 sh_cmt_clock_event_start(ch, 0);
748 break;
749 case CLOCK_EVT_MODE_SHUTDOWN:
750 case CLOCK_EVT_MODE_UNUSED:
751 sh_cmt_stop(ch, FLAG_CLOCKEVENT);
752 break;
753 default:
754 break;
758 static int sh_cmt_clock_event_next(unsigned long delta,
759 struct clock_event_device *ced)
761 struct sh_cmt_channel *ch = ced_to_sh_cmt(ced);
763 BUG_ON(ced->mode != CLOCK_EVT_MODE_ONESHOT);
764 if (likely(ch->flags & FLAG_IRQCONTEXT))
765 ch->next_match_value = delta - 1;
766 else
767 sh_cmt_set_next(ch, delta - 1);
769 return 0;
772 static void sh_cmt_clock_event_suspend(struct clock_event_device *ced)
774 struct sh_cmt_channel *ch = ced_to_sh_cmt(ced);
776 pm_genpd_syscore_poweroff(&ch->cmt->pdev->dev);
777 clk_unprepare(ch->cmt->clk);
780 static void sh_cmt_clock_event_resume(struct clock_event_device *ced)
782 struct sh_cmt_channel *ch = ced_to_sh_cmt(ced);
784 clk_prepare(ch->cmt->clk);
785 pm_genpd_syscore_poweron(&ch->cmt->pdev->dev);
788 static int sh_cmt_register_clockevent(struct sh_cmt_channel *ch,
789 const char *name)
791 struct clock_event_device *ced = &ch->ced;
792 int irq;
793 int ret;
795 irq = platform_get_irq(ch->cmt->pdev, ch->index);
796 if (irq < 0) {
797 dev_err(&ch->cmt->pdev->dev, "ch%u: failed to get irq\n",
798 ch->index);
799 return irq;
802 ret = request_irq(irq, sh_cmt_interrupt,
803 IRQF_TIMER | IRQF_IRQPOLL | IRQF_NOBALANCING,
804 dev_name(&ch->cmt->pdev->dev), ch);
805 if (ret) {
806 dev_err(&ch->cmt->pdev->dev, "ch%u: failed to request irq %d\n",
807 ch->index, irq);
808 return ret;
811 ced->name = name;
812 ced->features = CLOCK_EVT_FEAT_PERIODIC;
813 ced->features |= CLOCK_EVT_FEAT_ONESHOT;
814 ced->rating = 125;
815 ced->cpumask = cpu_possible_mask;
816 ced->set_next_event = sh_cmt_clock_event_next;
817 ced->set_mode = sh_cmt_clock_event_mode;
818 ced->suspend = sh_cmt_clock_event_suspend;
819 ced->resume = sh_cmt_clock_event_resume;
821 dev_info(&ch->cmt->pdev->dev, "ch%u: used for clock events\n",
822 ch->index);
823 clockevents_register_device(ced);
825 return 0;
828 static int sh_cmt_register(struct sh_cmt_channel *ch, const char *name,
829 bool clockevent, bool clocksource)
831 int ret;
833 if (clockevent) {
834 ch->cmt->has_clockevent = true;
835 ret = sh_cmt_register_clockevent(ch, name);
836 if (ret < 0)
837 return ret;
840 if (clocksource) {
841 ch->cmt->has_clocksource = true;
842 sh_cmt_register_clocksource(ch, name);
845 return 0;
848 static int sh_cmt_setup_channel(struct sh_cmt_channel *ch, unsigned int index,
849 unsigned int hwidx, bool clockevent,
850 bool clocksource, struct sh_cmt_device *cmt)
852 int ret;
854 /* Skip unused channels. */
855 if (!clockevent && !clocksource)
856 return 0;
858 ch->cmt = cmt;
859 ch->index = index;
860 ch->hwidx = hwidx;
863 * Compute the address of the channel control register block. For the
864 * timers with a per-channel start/stop register, compute its address
865 * as well.
867 switch (cmt->info->model) {
868 case SH_CMT_16BIT:
869 ch->ioctrl = cmt->mapbase + 2 + ch->hwidx * 6;
870 break;
871 case SH_CMT_32BIT:
872 case SH_CMT_48BIT:
873 ch->ioctrl = cmt->mapbase + 0x10 + ch->hwidx * 0x10;
874 break;
875 case SH_CMT_32BIT_FAST:
877 * The 32-bit "fast" timer has a single channel at hwidx 5 but
878 * is located at offset 0x40 instead of 0x60 for some reason.
880 ch->ioctrl = cmt->mapbase + 0x40;
881 break;
882 case SH_CMT_48BIT_GEN2:
883 ch->iostart = cmt->mapbase + ch->hwidx * 0x100;
884 ch->ioctrl = ch->iostart + 0x10;
885 break;
888 if (cmt->info->width == (sizeof(ch->max_match_value) * 8))
889 ch->max_match_value = ~0;
890 else
891 ch->max_match_value = (1 << cmt->info->width) - 1;
893 ch->match_value = ch->max_match_value;
894 raw_spin_lock_init(&ch->lock);
896 ch->timer_bit = cmt->info->model == SH_CMT_48BIT_GEN2 ? 0 : ch->hwidx;
898 ret = sh_cmt_register(ch, dev_name(&cmt->pdev->dev),
899 clockevent, clocksource);
900 if (ret) {
901 dev_err(&cmt->pdev->dev, "ch%u: registration failed\n",
902 ch->index);
903 return ret;
905 ch->cs_enabled = false;
907 return 0;
910 static int sh_cmt_map_memory(struct sh_cmt_device *cmt)
912 struct resource *mem;
914 mem = platform_get_resource(cmt->pdev, IORESOURCE_MEM, 0);
915 if (!mem) {
916 dev_err(&cmt->pdev->dev, "failed to get I/O memory\n");
917 return -ENXIO;
920 cmt->mapbase = ioremap_nocache(mem->start, resource_size(mem));
921 if (cmt->mapbase == NULL) {
922 dev_err(&cmt->pdev->dev, "failed to remap I/O memory\n");
923 return -ENXIO;
926 return 0;
929 static const struct platform_device_id sh_cmt_id_table[] = {
930 { "sh-cmt-16", (kernel_ulong_t)&sh_cmt_info[SH_CMT_16BIT] },
931 { "sh-cmt-32", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT] },
932 { "sh-cmt-32-fast", (kernel_ulong_t)&sh_cmt_info[SH_CMT_32BIT_FAST] },
933 { "sh-cmt-48", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT] },
934 { "sh-cmt-48-gen2", (kernel_ulong_t)&sh_cmt_info[SH_CMT_48BIT_GEN2] },
937 MODULE_DEVICE_TABLE(platform, sh_cmt_id_table);
939 static const struct of_device_id sh_cmt_of_table[] __maybe_unused = {
940 { .compatible = "renesas,cmt-32", .data = &sh_cmt_info[SH_CMT_32BIT] },
941 { .compatible = "renesas,cmt-32-fast", .data = &sh_cmt_info[SH_CMT_32BIT_FAST] },
942 { .compatible = "renesas,cmt-48", .data = &sh_cmt_info[SH_CMT_48BIT] },
943 { .compatible = "renesas,cmt-48-gen2", .data = &sh_cmt_info[SH_CMT_48BIT_GEN2] },
946 MODULE_DEVICE_TABLE(of, sh_cmt_of_table);
948 static int sh_cmt_parse_dt(struct sh_cmt_device *cmt)
950 struct device_node *np = cmt->pdev->dev.of_node;
952 return of_property_read_u32(np, "renesas,channels-mask",
953 &cmt->hw_channels);
956 static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev)
958 unsigned int mask;
959 unsigned int i;
960 int ret;
962 memset(cmt, 0, sizeof(*cmt));
963 cmt->pdev = pdev;
964 raw_spin_lock_init(&cmt->lock);
966 if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) {
967 const struct of_device_id *id;
969 id = of_match_node(sh_cmt_of_table, pdev->dev.of_node);
970 cmt->info = id->data;
972 ret = sh_cmt_parse_dt(cmt);
973 if (ret < 0)
974 return ret;
975 } else if (pdev->dev.platform_data) {
976 struct sh_timer_config *cfg = pdev->dev.platform_data;
977 const struct platform_device_id *id = pdev->id_entry;
979 cmt->info = (const struct sh_cmt_info *)id->driver_data;
980 cmt->hw_channels = cfg->channels_mask;
981 } else {
982 dev_err(&cmt->pdev->dev, "missing platform data\n");
983 return -ENXIO;
986 /* Get hold of clock. */
987 cmt->clk = clk_get(&cmt->pdev->dev, "fck");
988 if (IS_ERR(cmt->clk)) {
989 dev_err(&cmt->pdev->dev, "cannot get clock\n");
990 return PTR_ERR(cmt->clk);
993 ret = clk_prepare(cmt->clk);
994 if (ret < 0)
995 goto err_clk_put;
997 /* Map the memory resource(s). */
998 ret = sh_cmt_map_memory(cmt);
999 if (ret < 0)
1000 goto err_clk_unprepare;
1002 /* Allocate and setup the channels. */
1003 cmt->num_channels = hweight8(cmt->hw_channels);
1004 cmt->channels = kzalloc(cmt->num_channels * sizeof(*cmt->channels),
1005 GFP_KERNEL);
1006 if (cmt->channels == NULL) {
1007 ret = -ENOMEM;
1008 goto err_unmap;
1012 * Use the first channel as a clock event device and the second channel
1013 * as a clock source. If only one channel is available use it for both.
1015 for (i = 0, mask = cmt->hw_channels; i < cmt->num_channels; ++i) {
1016 unsigned int hwidx = ffs(mask) - 1;
1017 bool clocksource = i == 1 || cmt->num_channels == 1;
1018 bool clockevent = i == 0;
1020 ret = sh_cmt_setup_channel(&cmt->channels[i], i, hwidx,
1021 clockevent, clocksource, cmt);
1022 if (ret < 0)
1023 goto err_unmap;
1025 mask &= ~(1 << hwidx);
1028 platform_set_drvdata(pdev, cmt);
1030 return 0;
1032 err_unmap:
1033 kfree(cmt->channels);
1034 iounmap(cmt->mapbase);
1035 err_clk_unprepare:
1036 clk_unprepare(cmt->clk);
1037 err_clk_put:
1038 clk_put(cmt->clk);
1039 return ret;
1042 static int sh_cmt_probe(struct platform_device *pdev)
1044 struct sh_cmt_device *cmt = platform_get_drvdata(pdev);
1045 int ret;
1047 if (!is_early_platform_device(pdev)) {
1048 pm_runtime_set_active(&pdev->dev);
1049 pm_runtime_enable(&pdev->dev);
1052 if (cmt) {
1053 dev_info(&pdev->dev, "kept as earlytimer\n");
1054 goto out;
1057 cmt = kzalloc(sizeof(*cmt), GFP_KERNEL);
1058 if (cmt == NULL)
1059 return -ENOMEM;
1061 ret = sh_cmt_setup(cmt, pdev);
1062 if (ret) {
1063 kfree(cmt);
1064 pm_runtime_idle(&pdev->dev);
1065 return ret;
1067 if (is_early_platform_device(pdev))
1068 return 0;
1070 out:
1071 if (cmt->has_clockevent || cmt->has_clocksource)
1072 pm_runtime_irq_safe(&pdev->dev);
1073 else
1074 pm_runtime_idle(&pdev->dev);
1076 return 0;
1079 static int sh_cmt_remove(struct platform_device *pdev)
1081 return -EBUSY; /* cannot unregister clockevent and clocksource */
1084 static struct platform_driver sh_cmt_device_driver = {
1085 .probe = sh_cmt_probe,
1086 .remove = sh_cmt_remove,
1087 .driver = {
1088 .name = "sh_cmt",
1089 .of_match_table = of_match_ptr(sh_cmt_of_table),
1091 .id_table = sh_cmt_id_table,
1094 static int __init sh_cmt_init(void)
1096 return platform_driver_register(&sh_cmt_device_driver);
1099 static void __exit sh_cmt_exit(void)
1101 platform_driver_unregister(&sh_cmt_device_driver);
1104 early_platform_init("earlytimer", &sh_cmt_device_driver);
1105 subsys_initcall(sh_cmt_init);
1106 module_exit(sh_cmt_exit);
1108 MODULE_AUTHOR("Magnus Damm");
1109 MODULE_DESCRIPTION("SuperH CMT Timer Driver");
1110 MODULE_LICENSE("GPL v2");