Linux 2.6.25.3
[linux/fpc-iii.git] / arch / arm / mach-lh7a40x / lcd-panel.h
blobdf6e38ed425b3d63c0a0f491083405403a818cf4
1 /* lcd-panel.h
2 $Id$
4 written by Marc Singer
5 18 Jul 2005
7 Copyright (C) 2005 Marc Singer
9 -----------
10 DESCRIPTION
11 -----------
13 Only one panel may be defined at a time.
15 The pixel clock is calculated to be no greater than the target.
17 Each timing value is accompanied by a specification comment.
19 UNITS/MIN/TYP/MAX
21 Most of the units will be in clocks.
23 USE_RGB555
25 Define this macro to configure the AMBA LCD controller to use an
26 RGB555 encoding for the pels instead of the normal RGB565.
28 LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11
30 These boards are best approximated by 555 for all panels. Some
31 can use an extra low-order bit of blue in bit 16 of the color
32 value, but we don't have a way to communicate this non-linear
33 mapping to the kernel.
37 #if !defined (__LCD_PANEL_H__)
38 # define __LCD_PANEL_H__
40 #if defined (MACH_LPD79520)\
41 || defined (MACH_LPD79524)\
42 || defined (MACH_LPD7A400)\
43 || defined (MACH_LPD7A404)
44 # define USE_RGB555
45 #endif
47 struct clcd_panel_extra {
48 unsigned int hrmode;
49 unsigned int clsen;
50 unsigned int spsen;
51 unsigned int pcdel;
52 unsigned int revdel;
53 unsigned int lpdel;
54 unsigned int spldel;
55 unsigned int pc2del;
58 #define NS_TO_CLOCK(ns,c) ((((ns)*((c)/1000) + (1000000 - 1))/1000000))
59 #define CLOCK_TO_DIV(e,c) (((c) + (e) - 1)/(e))
61 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
63 /* Logic Product Development LCD 3.5" QVGA HRTFT -10 */
64 /* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */
66 #define PIX_CLOCK_TARGET (6800000)
67 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
68 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
70 static struct clcd_panel lcd_panel = {
71 .mode = {
72 .name = "3.5in QVGA (LQ035Q7DB02)",
73 .xres = 240,
74 .yres = 320,
75 .pixclock = PIX_CLOCK,
76 .left_margin = 16,
77 .right_margin = 21,
78 .upper_margin = 8, // line/8/8/8
79 .lower_margin = 5,
80 .hsync_len = 61,
81 .vsync_len = NS_TO_CLOCK (60, PIX_CLOCK),
82 .vmode = FB_VMODE_NONINTERLACED,
84 .width = -1,
85 .height = -1,
86 .tim2 = TIM2_IPC | (PIX_CLOCK_DIVIDER - 2),
87 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
88 .bpp = 16,
91 #define HAS_LCD_PANEL_EXTRA
93 static struct clcd_panel_extra lcd_panel_extra = {
94 .hrmode = 1,
95 .clsen = 1,
96 .spsen = 1,
97 .pcdel = 8,
98 .revdel = 7,
99 .lpdel = 13,
100 .spldel = 77,
101 .pc2del = 208,
104 #endif
106 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02
108 /* Logic Product Development LCD 5.7" QVGA -10 */
109 /* Sharp PN LQ057Q3DC02 */
110 /* QVGA mode, V/Q=LOW */
112 /* From Sharp on 2006.1.3. I believe some of the values are incorrect
113 * based on the datasheet.
115 Timing0 TIMING1 TIMING2 CONTROL
116 0x140A0C4C 0x080504EF 0x013F380D 0x00000829
117 HBP= 20 VBP= 8 BCD= 0
118 HFP= 10 VFP= 5 CPL=319
119 HSW= 12 VSW= 1 IOE= 0
120 PPL= 19 LPP=239 IPC= 1
121 IHS= 1
122 IVS= 1
123 ACB= 0
124 CSEL= 0
125 PCD= 13
129 /* The full horizontal cycle (Th) is clock/360/400/450. */
130 /* The full vertical cycle (Tv) is line/251/262/280. */
132 #define PIX_CLOCK_TARGET (6300000) /* -/6.3/7 MHz */
133 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
134 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
136 static struct clcd_panel lcd_panel = {
137 .mode = {
138 .name = "5.7in QVGA (LQ057Q3DC02)",
139 .xres = 320,
140 .yres = 240,
141 .pixclock = PIX_CLOCK,
142 .left_margin = 11,
143 .right_margin = 400-11-320-2,
144 .upper_margin = 7, // line/7/7/7
145 .lower_margin = 262-7-240-2,
146 .hsync_len = 2, // clk/2/96/200
147 .vsync_len = 2, // line/2/-/34
148 .vmode = FB_VMODE_NONINTERLACED,
150 .width = -1,
151 .height = -1,
152 .tim2 = TIM2_IHS | TIM2_IVS
153 | (PIX_CLOCK_DIVIDER - 2),
154 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
155 .bpp = 16,
158 #endif
160 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343
162 /* Logic Product Development LCD 6.4" VGA -10 */
163 /* Sharp PN LQ64D343 */
165 /* The full horizontal cycle (Th) is clock/750/800/900. */
166 /* The full vertical cycle (Tv) is line/515/525/560. */
168 #define PIX_CLOCK_TARGET (28330000)
169 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
170 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
172 static struct clcd_panel lcd_panel = {
173 .mode = {
174 .name = "6.4in QVGA (LQ64D343)",
175 .xres = 640,
176 .yres = 480,
177 .pixclock = PIX_CLOCK,
178 .left_margin = 32,
179 .right_margin = 800-32-640-96,
180 .upper_margin = 32, // line/34/34/34
181 .lower_margin = 540-32-480-2,
182 .hsync_len = 96, // clk/2/96/200
183 .vsync_len = 2, // line/2/-/34
184 .vmode = FB_VMODE_NONINTERLACED,
186 .width = -1,
187 .height = -1,
188 .tim2 = TIM2_IHS | TIM2_IVS
189 | (PIX_CLOCK_DIVIDER - 2),
190 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
191 .bpp = 16,
194 #endif
196 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368
198 /* Logic Product Development LCD 10.4" VGA -10 */
199 /* Sharp PN LQ10D368 */
201 #define PIX_CLOCK_TARGET (28330000)
202 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
203 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
205 static struct clcd_panel lcd_panel = {
206 .mode = {
207 .name = "10.4in VGA (LQ10D368)",
208 .xres = 640,
209 .yres = 480,
210 .pixclock = PIX_CLOCK,
211 .left_margin = 21,
212 .right_margin = 15,
213 .upper_margin = 34,
214 .lower_margin = 5,
215 .hsync_len = 96,
216 .vsync_len = 16,
217 .vmode = FB_VMODE_NONINTERLACED,
219 .width = -1,
220 .height = -1,
221 .tim2 = TIM2_IHS | TIM2_IVS
222 | (PIX_CLOCK_DIVIDER - 2),
223 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
224 .bpp = 16,
227 #endif
229 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41
231 /* Logic Product Development LCD 12.1" SVGA -10 */
232 /* Sharp PN LQ121S1DG41, was LQ121S1DG31 */
234 /* Note that with a 99993900 Hz HCLK, it is not possible to hit the
235 * target clock frequency range of 35MHz to 42MHz. */
237 /* If the target pixel clock is substantially lower than the panel
238 * spec, this is done to prevent the LCD display from glitching when
239 * the CPU is under load. A pixel clock higher than 25MHz
240 * (empirically determined) will compete with the CPU for bus cycles
241 * for the Ethernet chip. However, even a pixel clock of 10MHz
242 * competes with Compact Flash interface during some operations
243 * (fdisk, e2fsck). And, at that speed the display may have a visible
244 * flicker. */
246 /* The full horizontal cycle (Th) is clock/832/1056/1395. */
248 #define PIX_CLOCK_TARGET (20000000)
249 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
250 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
252 static struct clcd_panel lcd_panel = {
253 .mode = {
254 .name = "12.1in SVGA (LQ121S1DG41)",
255 .xres = 800,
256 .yres = 600,
257 .pixclock = PIX_CLOCK,
258 .left_margin = 89, // ns/5/-/(1/PIX_CLOCK)-10
259 .right_margin = 1056-800-89-128,
260 .upper_margin = 23, // line/23/23/23
261 .lower_margin = 44,
262 .hsync_len = 128, // clk/2/128/200
263 .vsync_len = 4, // line/2/4/6
264 .vmode = FB_VMODE_NONINTERLACED,
266 .width = -1,
267 .height = -1,
268 .tim2 = TIM2_IHS | TIM2_IVS
269 | (PIX_CLOCK_DIVIDER - 2),
270 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
271 .bpp = 16,
274 #endif
276 #if defined CONFIG_FB_ARMCLCD_HITACHI
278 /* Hitachi*/
279 /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
281 #define PIX_CLOCK_TARGET (49000000)
282 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
283 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
285 static struct clcd_panel lcd_panel = {
286 .mode = {
287 .name = "Hitachi 800x480",
288 .xres = 800,
289 .yres = 480,
290 .pixclock = PIX_CLOCK,
291 .left_margin = 88,
292 .right_margin = 40,
293 .upper_margin = 32,
294 .lower_margin = 11,
295 .hsync_len = 128,
296 .vsync_len = 2,
297 .vmode = FB_VMODE_NONINTERLACED,
299 .width = -1,
300 .height = -1,
301 .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
302 | (PIX_CLOCK_DIVIDER - 2),
303 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
304 .bpp = 16,
307 #endif
310 #if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE
312 /* AU Optotronics A070VW01 7.0 Wide Screen color Display*/
313 /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
315 #define PIX_CLOCK_TARGET (10000000)
316 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
317 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
319 static struct clcd_panel lcd_panel = {
320 .mode = {
321 .name = "7.0in Wide (A070VW01)",
322 .xres = 480,
323 .yres = 234,
324 .pixclock = PIX_CLOCK,
325 .left_margin = 30,
326 .right_margin = 25,
327 .upper_margin = 14,
328 .lower_margin = 12,
329 .hsync_len = 100,
330 .vsync_len = 1,
331 .vmode = FB_VMODE_NONINTERLACED,
333 .width = -1,
334 .height = -1,
335 .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
336 | (PIX_CLOCK_DIVIDER - 2),
337 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
338 .bpp = 16,
341 #endif
343 #undef NS_TO_CLOCK
344 #undef CLOCK_TO_DIV
346 #endif /* __LCD_PANEL_H__ */