2 * drivers/mmc/host/omap_hsmmc.c
4 * Driver for OMAP2430/3430 MMC controller.
6 * Copyright (C) 2007 Texas Instruments.
9 * Syed Mohammed Khasim <x0khasim@ti.com>
10 * Madhusudhan <madhu.cr@ti.com>
11 * Mohit Jalori <mjalori@ti.com>
13 * This file is licensed under the terms of the GNU General Public License
14 * version 2. This program is licensed "as is" without any warranty of any
15 * kind, whether express or implied.
18 #include <linux/module.h>
19 #include <linux/init.h>
20 #include <linux/kernel.h>
21 #include <linux/debugfs.h>
22 #include <linux/dmaengine.h>
23 #include <linux/seq_file.h>
24 #include <linux/interrupt.h>
25 #include <linux/delay.h>
26 #include <linux/dma-mapping.h>
27 #include <linux/platform_device.h>
28 #include <linux/timer.h>
29 #include <linux/clk.h>
31 #include <linux/of_gpio.h>
32 #include <linux/of_device.h>
33 #include <linux/omap-dma.h>
34 #include <linux/mmc/host.h>
35 #include <linux/mmc/core.h>
36 #include <linux/mmc/mmc.h>
38 #include <linux/gpio.h>
39 #include <linux/regulator/consumer.h>
40 #include <linux/pinctrl/consumer.h>
41 #include <linux/pm_runtime.h>
42 #include <linux/platform_data/mmc-omap.h>
44 /* OMAP HSMMC Host Controller Registers */
45 #define OMAP_HSMMC_SYSSTATUS 0x0014
46 #define OMAP_HSMMC_CON 0x002C
47 #define OMAP_HSMMC_BLK 0x0104
48 #define OMAP_HSMMC_ARG 0x0108
49 #define OMAP_HSMMC_CMD 0x010C
50 #define OMAP_HSMMC_RSP10 0x0110
51 #define OMAP_HSMMC_RSP32 0x0114
52 #define OMAP_HSMMC_RSP54 0x0118
53 #define OMAP_HSMMC_RSP76 0x011C
54 #define OMAP_HSMMC_DATA 0x0120
55 #define OMAP_HSMMC_HCTL 0x0128
56 #define OMAP_HSMMC_SYSCTL 0x012C
57 #define OMAP_HSMMC_STAT 0x0130
58 #define OMAP_HSMMC_IE 0x0134
59 #define OMAP_HSMMC_ISE 0x0138
60 #define OMAP_HSMMC_CAPA 0x0140
62 #define VS18 (1 << 26)
63 #define VS30 (1 << 25)
65 #define SDVS18 (0x5 << 9)
66 #define SDVS30 (0x6 << 9)
67 #define SDVS33 (0x7 << 9)
68 #define SDVS_MASK 0x00000E00
69 #define SDVSCLR 0xFFFFF1FF
70 #define SDVSDET 0x00000400
77 #define CLKD_MASK 0x0000FFC0
79 #define DTO_MASK 0x000F0000
81 #define INIT_STREAM (1 << 1)
82 #define DP_SELECT (1 << 21)
87 #define FOUR_BIT (1 << 1)
92 #define STAT_CLEAR 0xFFFFFFFF
93 #define INIT_STREAM_CMD 0x00000000
94 #define DUAL_VOLT_OCR_BIT 7
97 #define SOFTRESET (1 << 1)
98 #define RESETDONE (1 << 0)
100 /* Interrupt masks for IE and ISE register */
101 #define CC_EN (1 << 0)
102 #define TC_EN (1 << 1)
103 #define BWR_EN (1 << 4)
104 #define BRR_EN (1 << 5)
105 #define ERR_EN (1 << 15)
106 #define CTO_EN (1 << 16)
107 #define CCRC_EN (1 << 17)
108 #define CEB_EN (1 << 18)
109 #define CIE_EN (1 << 19)
110 #define DTO_EN (1 << 20)
111 #define DCRC_EN (1 << 21)
112 #define DEB_EN (1 << 22)
113 #define CERR_EN (1 << 28)
114 #define BADA_EN (1 << 29)
116 #define INT_EN_MASK (BADA_EN | CERR_EN | DEB_EN | DCRC_EN |\
117 DTO_EN | CIE_EN | CEB_EN | CCRC_EN | CTO_EN | \
118 BRR_EN | BWR_EN | TC_EN | CC_EN)
120 #define MMC_AUTOSUSPEND_DELAY 100
121 #define MMC_TIMEOUT_MS 20
122 #define OMAP_MMC_MIN_CLOCK 400000
123 #define OMAP_MMC_MAX_CLOCK 52000000
124 #define DRIVER_NAME "omap_hsmmc"
127 * One controller can have multiple slots, like on some omap boards using
128 * omap.c controller driver. Luckily this is not currently done on any known
129 * omap_hsmmc.c device.
131 #define mmc_slot(host) (host->pdata->slots[host->slot_id])
134 * MMC Host controller read/write API's
136 #define OMAP_HSMMC_READ(base, reg) \
137 __raw_readl((base) + OMAP_HSMMC_##reg)
139 #define OMAP_HSMMC_WRITE(base, reg, val) \
140 __raw_writel((val), (base) + OMAP_HSMMC_##reg)
142 struct omap_hsmmc_next
{
143 unsigned int dma_len
;
147 struct omap_hsmmc_host
{
149 struct mmc_host
*mmc
;
150 struct mmc_request
*mrq
;
151 struct mmc_command
*cmd
;
152 struct mmc_data
*data
;
156 * vcc == configured supply
157 * vcc_aux == optional
158 * - MMC1, supply for DAT4..DAT7
159 * - MMC2/MMC2, external level shifter voltage supply, for
160 * chip (SDIO, eMMC, etc) or transceiver (MMC2 only)
162 struct regulator
*vcc
;
163 struct regulator
*vcc_aux
;
165 resource_size_t mapbase
;
166 spinlock_t irq_lock
; /* Prevent races with irq handler */
167 unsigned int dma_len
;
168 unsigned int dma_sg_idx
;
169 unsigned char bus_mode
;
170 unsigned char power_mode
;
174 struct dma_chan
*tx_chan
;
175 struct dma_chan
*rx_chan
;
183 struct omap_hsmmc_next next_data
;
185 struct omap_mmc_platform_data
*pdata
;
188 static int omap_hsmmc_card_detect(struct device
*dev
, int slot
)
190 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
191 struct omap_mmc_platform_data
*mmc
= host
->pdata
;
193 /* NOTE: assumes card detect signal is active-low */
194 return !gpio_get_value_cansleep(mmc
->slots
[0].switch_pin
);
197 static int omap_hsmmc_get_wp(struct device
*dev
, int slot
)
199 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
200 struct omap_mmc_platform_data
*mmc
= host
->pdata
;
202 /* NOTE: assumes write protect signal is active-high */
203 return gpio_get_value_cansleep(mmc
->slots
[0].gpio_wp
);
206 static int omap_hsmmc_get_cover_state(struct device
*dev
, int slot
)
208 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
209 struct omap_mmc_platform_data
*mmc
= host
->pdata
;
211 /* NOTE: assumes card detect signal is active-low */
212 return !gpio_get_value_cansleep(mmc
->slots
[0].switch_pin
);
217 static int omap_hsmmc_suspend_cdirq(struct device
*dev
, int slot
)
219 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
220 struct omap_mmc_platform_data
*mmc
= host
->pdata
;
222 disable_irq(mmc
->slots
[0].card_detect_irq
);
226 static int omap_hsmmc_resume_cdirq(struct device
*dev
, int slot
)
228 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
229 struct omap_mmc_platform_data
*mmc
= host
->pdata
;
231 enable_irq(mmc
->slots
[0].card_detect_irq
);
237 #define omap_hsmmc_suspend_cdirq NULL
238 #define omap_hsmmc_resume_cdirq NULL
242 #ifdef CONFIG_REGULATOR
244 static int omap_hsmmc_set_power(struct device
*dev
, int slot
, int power_on
,
247 struct omap_hsmmc_host
*host
=
248 platform_get_drvdata(to_platform_device(dev
));
252 * If we don't see a Vcc regulator, assume it's a fixed
253 * voltage always-on regulator.
258 * With DT, never turn OFF the regulator. This is because
259 * the pbias cell programming support is still missing when
260 * booting with Device tree
262 if (dev
->of_node
&& !vdd
)
265 if (mmc_slot(host
).before_set_reg
)
266 mmc_slot(host
).before_set_reg(dev
, slot
, power_on
, vdd
);
269 * Assume Vcc regulator is used only to power the card ... OMAP
270 * VDDS is used to power the pins, optionally with a transceiver to
271 * support cards using voltages other than VDDS (1.8V nominal). When a
272 * transceiver is used, DAT3..7 are muxed as transceiver control pins.
274 * In some cases this regulator won't support enable/disable;
275 * e.g. it's a fixed rail for a WLAN chip.
277 * In other cases vcc_aux switches interface power. Example, for
278 * eMMC cards it represents VccQ. Sometimes transceivers or SDIO
279 * chips/cards need an interface voltage rail too.
282 ret
= mmc_regulator_set_ocr(host
->mmc
, host
->vcc
, vdd
);
283 /* Enable interface voltage rail, if needed */
284 if (ret
== 0 && host
->vcc_aux
) {
285 ret
= regulator_enable(host
->vcc_aux
);
287 ret
= mmc_regulator_set_ocr(host
->mmc
,
291 /* Shut down the rail */
293 ret
= regulator_disable(host
->vcc_aux
);
295 /* Then proceed to shut down the local regulator */
296 ret
= mmc_regulator_set_ocr(host
->mmc
,
301 if (mmc_slot(host
).after_set_reg
)
302 mmc_slot(host
).after_set_reg(dev
, slot
, power_on
, vdd
);
307 static int omap_hsmmc_reg_get(struct omap_hsmmc_host
*host
)
309 struct regulator
*reg
;
312 reg
= regulator_get(host
->dev
, "vmmc");
314 dev_err(host
->dev
, "vmmc regulator missing\n");
317 mmc_slot(host
).set_power
= omap_hsmmc_set_power
;
319 ocr_value
= mmc_regulator_get_ocrmask(reg
);
320 if (!mmc_slot(host
).ocr_mask
) {
321 mmc_slot(host
).ocr_mask
= ocr_value
;
323 if (!(mmc_slot(host
).ocr_mask
& ocr_value
)) {
324 dev_err(host
->dev
, "ocrmask %x is not supported\n",
325 mmc_slot(host
).ocr_mask
);
326 mmc_slot(host
).ocr_mask
= 0;
331 /* Allow an aux regulator */
332 reg
= regulator_get(host
->dev
, "vmmc_aux");
333 host
->vcc_aux
= IS_ERR(reg
) ? NULL
: reg
;
335 /* For eMMC do not power off when not in sleep state */
336 if (mmc_slot(host
).no_regulator_off_init
)
339 * UGLY HACK: workaround regulator framework bugs.
340 * When the bootloader leaves a supply active, it's
341 * initialized with zero usecount ... and we can't
342 * disable it without first enabling it. Until the
343 * framework is fixed, we need a workaround like this
344 * (which is safe for MMC, but not in general).
346 if (regulator_is_enabled(host
->vcc
) > 0 ||
347 (host
->vcc_aux
&& regulator_is_enabled(host
->vcc_aux
))) {
348 int vdd
= ffs(mmc_slot(host
).ocr_mask
) - 1;
350 mmc_slot(host
).set_power(host
->dev
, host
->slot_id
,
352 mmc_slot(host
).set_power(host
->dev
, host
->slot_id
,
360 static void omap_hsmmc_reg_put(struct omap_hsmmc_host
*host
)
362 regulator_put(host
->vcc
);
363 regulator_put(host
->vcc_aux
);
364 mmc_slot(host
).set_power
= NULL
;
367 static inline int omap_hsmmc_have_reg(void)
374 static inline int omap_hsmmc_reg_get(struct omap_hsmmc_host
*host
)
379 static inline void omap_hsmmc_reg_put(struct omap_hsmmc_host
*host
)
383 static inline int omap_hsmmc_have_reg(void)
390 static int omap_hsmmc_gpio_init(struct omap_mmc_platform_data
*pdata
)
394 if (gpio_is_valid(pdata
->slots
[0].switch_pin
)) {
395 if (pdata
->slots
[0].cover
)
396 pdata
->slots
[0].get_cover_state
=
397 omap_hsmmc_get_cover_state
;
399 pdata
->slots
[0].card_detect
= omap_hsmmc_card_detect
;
400 pdata
->slots
[0].card_detect_irq
=
401 gpio_to_irq(pdata
->slots
[0].switch_pin
);
402 ret
= gpio_request(pdata
->slots
[0].switch_pin
, "mmc_cd");
405 ret
= gpio_direction_input(pdata
->slots
[0].switch_pin
);
409 pdata
->slots
[0].switch_pin
= -EINVAL
;
411 if (gpio_is_valid(pdata
->slots
[0].gpio_wp
)) {
412 pdata
->slots
[0].get_ro
= omap_hsmmc_get_wp
;
413 ret
= gpio_request(pdata
->slots
[0].gpio_wp
, "mmc_wp");
416 ret
= gpio_direction_input(pdata
->slots
[0].gpio_wp
);
420 pdata
->slots
[0].gpio_wp
= -EINVAL
;
425 gpio_free(pdata
->slots
[0].gpio_wp
);
427 if (gpio_is_valid(pdata
->slots
[0].switch_pin
))
429 gpio_free(pdata
->slots
[0].switch_pin
);
433 static void omap_hsmmc_gpio_free(struct omap_mmc_platform_data
*pdata
)
435 if (gpio_is_valid(pdata
->slots
[0].gpio_wp
))
436 gpio_free(pdata
->slots
[0].gpio_wp
);
437 if (gpio_is_valid(pdata
->slots
[0].switch_pin
))
438 gpio_free(pdata
->slots
[0].switch_pin
);
442 * Start clock to the card
444 static void omap_hsmmc_start_clock(struct omap_hsmmc_host
*host
)
446 OMAP_HSMMC_WRITE(host
->base
, SYSCTL
,
447 OMAP_HSMMC_READ(host
->base
, SYSCTL
) | CEN
);
451 * Stop clock to the card
453 static void omap_hsmmc_stop_clock(struct omap_hsmmc_host
*host
)
455 OMAP_HSMMC_WRITE(host
->base
, SYSCTL
,
456 OMAP_HSMMC_READ(host
->base
, SYSCTL
) & ~CEN
);
457 if ((OMAP_HSMMC_READ(host
->base
, SYSCTL
) & CEN
) != 0x0)
458 dev_dbg(mmc_dev(host
->mmc
), "MMC Clock is not stopped\n");
461 static void omap_hsmmc_enable_irq(struct omap_hsmmc_host
*host
,
462 struct mmc_command
*cmd
)
464 unsigned int irq_mask
;
467 irq_mask
= INT_EN_MASK
& ~(BRR_EN
| BWR_EN
);
469 irq_mask
= INT_EN_MASK
;
471 /* Disable timeout for erases */
472 if (cmd
->opcode
== MMC_ERASE
)
475 OMAP_HSMMC_WRITE(host
->base
, STAT
, STAT_CLEAR
);
476 OMAP_HSMMC_WRITE(host
->base
, ISE
, irq_mask
);
477 OMAP_HSMMC_WRITE(host
->base
, IE
, irq_mask
);
480 static void omap_hsmmc_disable_irq(struct omap_hsmmc_host
*host
)
482 OMAP_HSMMC_WRITE(host
->base
, ISE
, 0);
483 OMAP_HSMMC_WRITE(host
->base
, IE
, 0);
484 OMAP_HSMMC_WRITE(host
->base
, STAT
, STAT_CLEAR
);
487 /* Calculate divisor for the given clock frequency */
488 static u16
calc_divisor(struct omap_hsmmc_host
*host
, struct mmc_ios
*ios
)
493 dsor
= DIV_ROUND_UP(clk_get_rate(host
->fclk
), ios
->clock
);
501 static void omap_hsmmc_set_clock(struct omap_hsmmc_host
*host
)
503 struct mmc_ios
*ios
= &host
->mmc
->ios
;
504 unsigned long regval
;
505 unsigned long timeout
;
506 unsigned long clkdiv
;
508 dev_vdbg(mmc_dev(host
->mmc
), "Set clock to %uHz\n", ios
->clock
);
510 omap_hsmmc_stop_clock(host
);
512 regval
= OMAP_HSMMC_READ(host
->base
, SYSCTL
);
513 regval
= regval
& ~(CLKD_MASK
| DTO_MASK
);
514 clkdiv
= calc_divisor(host
, ios
);
515 regval
= regval
| (clkdiv
<< 6) | (DTO
<< 16);
516 OMAP_HSMMC_WRITE(host
->base
, SYSCTL
, regval
);
517 OMAP_HSMMC_WRITE(host
->base
, SYSCTL
,
518 OMAP_HSMMC_READ(host
->base
, SYSCTL
) | ICE
);
520 /* Wait till the ICS bit is set */
521 timeout
= jiffies
+ msecs_to_jiffies(MMC_TIMEOUT_MS
);
522 while ((OMAP_HSMMC_READ(host
->base
, SYSCTL
) & ICS
) != ICS
523 && time_before(jiffies
, timeout
))
527 * Enable High-Speed Support
529 * - Controller should support High-Speed-Enable Bit
530 * - Controller should not be using DDR Mode
531 * - Controller should advertise that it supports High Speed
532 * in capabilities register
533 * - MMC/SD clock coming out of controller > 25MHz
535 if ((mmc_slot(host
).features
& HSMMC_HAS_HSPE_SUPPORT
) &&
536 (ios
->timing
!= MMC_TIMING_UHS_DDR50
) &&
537 ((OMAP_HSMMC_READ(host
->base
, CAPA
) & HSS
) == HSS
)) {
538 regval
= OMAP_HSMMC_READ(host
->base
, HCTL
);
539 if (clkdiv
&& (clk_get_rate(host
->fclk
)/clkdiv
) > 25000000)
544 OMAP_HSMMC_WRITE(host
->base
, HCTL
, regval
);
547 omap_hsmmc_start_clock(host
);
550 static void omap_hsmmc_set_bus_width(struct omap_hsmmc_host
*host
)
552 struct mmc_ios
*ios
= &host
->mmc
->ios
;
555 con
= OMAP_HSMMC_READ(host
->base
, CON
);
556 if (ios
->timing
== MMC_TIMING_UHS_DDR50
)
557 con
|= DDR
; /* configure in DDR mode */
560 switch (ios
->bus_width
) {
561 case MMC_BUS_WIDTH_8
:
562 OMAP_HSMMC_WRITE(host
->base
, CON
, con
| DW8
);
564 case MMC_BUS_WIDTH_4
:
565 OMAP_HSMMC_WRITE(host
->base
, CON
, con
& ~DW8
);
566 OMAP_HSMMC_WRITE(host
->base
, HCTL
,
567 OMAP_HSMMC_READ(host
->base
, HCTL
) | FOUR_BIT
);
569 case MMC_BUS_WIDTH_1
:
570 OMAP_HSMMC_WRITE(host
->base
, CON
, con
& ~DW8
);
571 OMAP_HSMMC_WRITE(host
->base
, HCTL
,
572 OMAP_HSMMC_READ(host
->base
, HCTL
) & ~FOUR_BIT
);
577 static void omap_hsmmc_set_bus_mode(struct omap_hsmmc_host
*host
)
579 struct mmc_ios
*ios
= &host
->mmc
->ios
;
582 con
= OMAP_HSMMC_READ(host
->base
, CON
);
583 if (ios
->bus_mode
== MMC_BUSMODE_OPENDRAIN
)
584 OMAP_HSMMC_WRITE(host
->base
, CON
, con
| OD
);
586 OMAP_HSMMC_WRITE(host
->base
, CON
, con
& ~OD
);
592 * Restore the MMC host context, if it was lost as result of a
593 * power state change.
595 static int omap_hsmmc_context_restore(struct omap_hsmmc_host
*host
)
597 struct mmc_ios
*ios
= &host
->mmc
->ios
;
598 struct omap_mmc_platform_data
*pdata
= host
->pdata
;
599 int context_loss
= 0;
601 unsigned long timeout
;
603 if (pdata
->get_context_loss_count
) {
604 context_loss
= pdata
->get_context_loss_count(host
->dev
);
605 if (context_loss
< 0)
609 dev_dbg(mmc_dev(host
->mmc
), "context was %slost\n",
610 context_loss
== host
->context_loss
? "not " : "");
611 if (host
->context_loss
== context_loss
)
614 if (!OMAP_HSMMC_READ(host
->base
, SYSSTATUS
) & RESETDONE
)
617 if (host
->pdata
->controller_flags
& OMAP_HSMMC_SUPPORTS_DUAL_VOLT
) {
618 if (host
->power_mode
!= MMC_POWER_OFF
&&
619 (1 << ios
->vdd
) <= MMC_VDD_23_24
)
629 OMAP_HSMMC_WRITE(host
->base
, HCTL
,
630 OMAP_HSMMC_READ(host
->base
, HCTL
) | hctl
);
632 OMAP_HSMMC_WRITE(host
->base
, CAPA
,
633 OMAP_HSMMC_READ(host
->base
, CAPA
) | capa
);
635 OMAP_HSMMC_WRITE(host
->base
, HCTL
,
636 OMAP_HSMMC_READ(host
->base
, HCTL
) | SDBP
);
638 timeout
= jiffies
+ msecs_to_jiffies(MMC_TIMEOUT_MS
);
639 while ((OMAP_HSMMC_READ(host
->base
, HCTL
) & SDBP
) != SDBP
640 && time_before(jiffies
, timeout
))
643 omap_hsmmc_disable_irq(host
);
645 /* Do not initialize card-specific things if the power is off */
646 if (host
->power_mode
== MMC_POWER_OFF
)
649 omap_hsmmc_set_bus_width(host
);
651 omap_hsmmc_set_clock(host
);
653 omap_hsmmc_set_bus_mode(host
);
656 host
->context_loss
= context_loss
;
658 dev_dbg(mmc_dev(host
->mmc
), "context is restored\n");
663 * Save the MMC host context (store the number of power state changes so far).
665 static void omap_hsmmc_context_save(struct omap_hsmmc_host
*host
)
667 struct omap_mmc_platform_data
*pdata
= host
->pdata
;
670 if (pdata
->get_context_loss_count
) {
671 context_loss
= pdata
->get_context_loss_count(host
->dev
);
672 if (context_loss
< 0)
674 host
->context_loss
= context_loss
;
680 static int omap_hsmmc_context_restore(struct omap_hsmmc_host
*host
)
685 static void omap_hsmmc_context_save(struct omap_hsmmc_host
*host
)
692 * Send init stream sequence to card
693 * before sending IDLE command
695 static void send_init_stream(struct omap_hsmmc_host
*host
)
698 unsigned long timeout
;
700 if (host
->protect_card
)
703 disable_irq(host
->irq
);
705 OMAP_HSMMC_WRITE(host
->base
, IE
, INT_EN_MASK
);
706 OMAP_HSMMC_WRITE(host
->base
, CON
,
707 OMAP_HSMMC_READ(host
->base
, CON
) | INIT_STREAM
);
708 OMAP_HSMMC_WRITE(host
->base
, CMD
, INIT_STREAM_CMD
);
710 timeout
= jiffies
+ msecs_to_jiffies(MMC_TIMEOUT_MS
);
711 while ((reg
!= CC_EN
) && time_before(jiffies
, timeout
))
712 reg
= OMAP_HSMMC_READ(host
->base
, STAT
) & CC_EN
;
714 OMAP_HSMMC_WRITE(host
->base
, CON
,
715 OMAP_HSMMC_READ(host
->base
, CON
) & ~INIT_STREAM
);
717 OMAP_HSMMC_WRITE(host
->base
, STAT
, STAT_CLEAR
);
718 OMAP_HSMMC_READ(host
->base
, STAT
);
720 enable_irq(host
->irq
);
724 int omap_hsmmc_cover_is_closed(struct omap_hsmmc_host
*host
)
728 if (mmc_slot(host
).get_cover_state
)
729 r
= mmc_slot(host
).get_cover_state(host
->dev
, host
->slot_id
);
734 omap_hsmmc_show_cover_switch(struct device
*dev
, struct device_attribute
*attr
,
737 struct mmc_host
*mmc
= container_of(dev
, struct mmc_host
, class_dev
);
738 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
740 return sprintf(buf
, "%s\n",
741 omap_hsmmc_cover_is_closed(host
) ? "closed" : "open");
744 static DEVICE_ATTR(cover_switch
, S_IRUGO
, omap_hsmmc_show_cover_switch
, NULL
);
747 omap_hsmmc_show_slot_name(struct device
*dev
, struct device_attribute
*attr
,
750 struct mmc_host
*mmc
= container_of(dev
, struct mmc_host
, class_dev
);
751 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
753 return sprintf(buf
, "%s\n", mmc_slot(host
).name
);
756 static DEVICE_ATTR(slot_name
, S_IRUGO
, omap_hsmmc_show_slot_name
, NULL
);
759 * Configure the response type and send the cmd.
762 omap_hsmmc_start_command(struct omap_hsmmc_host
*host
, struct mmc_command
*cmd
,
763 struct mmc_data
*data
)
765 int cmdreg
= 0, resptype
= 0, cmdtype
= 0;
767 dev_vdbg(mmc_dev(host
->mmc
), "%s: CMD%d, argument 0x%08x\n",
768 mmc_hostname(host
->mmc
), cmd
->opcode
, cmd
->arg
);
771 omap_hsmmc_enable_irq(host
, cmd
);
773 host
->response_busy
= 0;
774 if (cmd
->flags
& MMC_RSP_PRESENT
) {
775 if (cmd
->flags
& MMC_RSP_136
)
777 else if (cmd
->flags
& MMC_RSP_BUSY
) {
779 host
->response_busy
= 1;
785 * Unlike OMAP1 controller, the cmdtype does not seem to be based on
786 * ac, bc, adtc, bcr. Only commands ending an open ended transfer need
787 * a val of 0x3, rest 0x0.
789 if (cmd
== host
->mrq
->stop
)
792 cmdreg
= (cmd
->opcode
<< 24) | (resptype
<< 16) | (cmdtype
<< 22);
795 cmdreg
|= DP_SELECT
| MSBS
| BCE
;
796 if (data
->flags
& MMC_DATA_READ
)
805 host
->req_in_progress
= 1;
807 OMAP_HSMMC_WRITE(host
->base
, ARG
, cmd
->arg
);
808 OMAP_HSMMC_WRITE(host
->base
, CMD
, cmdreg
);
812 omap_hsmmc_get_dma_dir(struct omap_hsmmc_host
*host
, struct mmc_data
*data
)
814 if (data
->flags
& MMC_DATA_WRITE
)
815 return DMA_TO_DEVICE
;
817 return DMA_FROM_DEVICE
;
820 static struct dma_chan
*omap_hsmmc_get_dma_chan(struct omap_hsmmc_host
*host
,
821 struct mmc_data
*data
)
823 return data
->flags
& MMC_DATA_WRITE
? host
->tx_chan
: host
->rx_chan
;
826 static void omap_hsmmc_request_done(struct omap_hsmmc_host
*host
, struct mmc_request
*mrq
)
831 spin_lock_irqsave(&host
->irq_lock
, flags
);
832 host
->req_in_progress
= 0;
833 dma_ch
= host
->dma_ch
;
834 spin_unlock_irqrestore(&host
->irq_lock
, flags
);
836 omap_hsmmc_disable_irq(host
);
837 /* Do not complete the request if DMA is still in progress */
838 if (mrq
->data
&& host
->use_dma
&& dma_ch
!= -1)
841 mmc_request_done(host
->mmc
, mrq
);
845 * Notify the transfer complete to MMC core
848 omap_hsmmc_xfer_done(struct omap_hsmmc_host
*host
, struct mmc_data
*data
)
851 struct mmc_request
*mrq
= host
->mrq
;
853 /* TC before CC from CMD6 - don't know why, but it happens */
854 if (host
->cmd
&& host
->cmd
->opcode
== 6 &&
855 host
->response_busy
) {
856 host
->response_busy
= 0;
860 omap_hsmmc_request_done(host
, mrq
);
867 data
->bytes_xfered
+= data
->blocks
* (data
->blksz
);
869 data
->bytes_xfered
= 0;
872 omap_hsmmc_request_done(host
, data
->mrq
);
875 omap_hsmmc_start_command(host
, data
->stop
, NULL
);
879 * Notify the core about command completion
882 omap_hsmmc_cmd_done(struct omap_hsmmc_host
*host
, struct mmc_command
*cmd
)
886 if (cmd
->flags
& MMC_RSP_PRESENT
) {
887 if (cmd
->flags
& MMC_RSP_136
) {
888 /* response type 2 */
889 cmd
->resp
[3] = OMAP_HSMMC_READ(host
->base
, RSP10
);
890 cmd
->resp
[2] = OMAP_HSMMC_READ(host
->base
, RSP32
);
891 cmd
->resp
[1] = OMAP_HSMMC_READ(host
->base
, RSP54
);
892 cmd
->resp
[0] = OMAP_HSMMC_READ(host
->base
, RSP76
);
894 /* response types 1, 1b, 3, 4, 5, 6 */
895 cmd
->resp
[0] = OMAP_HSMMC_READ(host
->base
, RSP10
);
898 if ((host
->data
== NULL
&& !host
->response_busy
) || cmd
->error
)
899 omap_hsmmc_request_done(host
, cmd
->mrq
);
903 * DMA clean up for command errors
905 static void omap_hsmmc_dma_cleanup(struct omap_hsmmc_host
*host
, int errno
)
910 host
->data
->error
= errno
;
912 spin_lock_irqsave(&host
->irq_lock
, flags
);
913 dma_ch
= host
->dma_ch
;
915 spin_unlock_irqrestore(&host
->irq_lock
, flags
);
917 if (host
->use_dma
&& dma_ch
!= -1) {
918 struct dma_chan
*chan
= omap_hsmmc_get_dma_chan(host
, host
->data
);
920 dmaengine_terminate_all(chan
);
921 dma_unmap_sg(chan
->device
->dev
,
922 host
->data
->sg
, host
->data
->sg_len
,
923 omap_hsmmc_get_dma_dir(host
, host
->data
));
925 host
->data
->host_cookie
= 0;
931 * Readable error output
933 #ifdef CONFIG_MMC_DEBUG
934 static void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host
*host
, u32 status
)
936 /* --- means reserved bit without definition at documentation */
937 static const char *omap_hsmmc_status_bits
[] = {
938 "CC" , "TC" , "BGE", "---", "BWR" , "BRR" , "---" , "---" ,
939 "CIRQ", "OBI" , "---", "---", "---" , "---" , "---" , "ERRI",
940 "CTO" , "CCRC", "CEB", "CIE", "DTO" , "DCRC", "DEB" , "---" ,
941 "ACE" , "---" , "---", "---", "CERR", "BADA", "---" , "---"
947 len
= sprintf(buf
, "MMC IRQ 0x%x :", status
);
950 for (i
= 0; i
< ARRAY_SIZE(omap_hsmmc_status_bits
); i
++)
951 if (status
& (1 << i
)) {
952 len
= sprintf(buf
, " %s", omap_hsmmc_status_bits
[i
]);
956 dev_vdbg(mmc_dev(host
->mmc
), "%s\n", res
);
959 static inline void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host
*host
,
963 #endif /* CONFIG_MMC_DEBUG */
966 * MMC controller internal state machines reset
968 * Used to reset command or data internal state machines, using respectively
969 * SRC or SRD bit of SYSCTL register
970 * Can be called from interrupt context
972 static inline void omap_hsmmc_reset_controller_fsm(struct omap_hsmmc_host
*host
,
976 unsigned long limit
= (loops_per_jiffy
*
977 msecs_to_jiffies(MMC_TIMEOUT_MS
));
979 OMAP_HSMMC_WRITE(host
->base
, SYSCTL
,
980 OMAP_HSMMC_READ(host
->base
, SYSCTL
) | bit
);
983 * OMAP4 ES2 and greater has an updated reset logic.
984 * Monitor a 0->1 transition first
986 if (mmc_slot(host
).features
& HSMMC_HAS_UPDATED_RESET
) {
987 while ((!(OMAP_HSMMC_READ(host
->base
, SYSCTL
) & bit
))
993 while ((OMAP_HSMMC_READ(host
->base
, SYSCTL
) & bit
) &&
997 if (OMAP_HSMMC_READ(host
->base
, SYSCTL
) & bit
)
998 dev_err(mmc_dev(host
->mmc
),
999 "Timeout waiting on controller reset in %s\n",
1003 static void hsmmc_command_incomplete(struct omap_hsmmc_host
*host
,
1004 int err
, int end_cmd
)
1007 omap_hsmmc_reset_controller_fsm(host
, SRC
);
1009 host
->cmd
->error
= err
;
1013 omap_hsmmc_reset_controller_fsm(host
, SRD
);
1014 omap_hsmmc_dma_cleanup(host
, err
);
1015 } else if (host
->mrq
&& host
->mrq
->cmd
)
1016 host
->mrq
->cmd
->error
= err
;
1019 static void omap_hsmmc_do_irq(struct omap_hsmmc_host
*host
, int status
)
1021 struct mmc_data
*data
;
1022 int end_cmd
= 0, end_trans
= 0;
1025 dev_vdbg(mmc_dev(host
->mmc
), "IRQ Status is %x\n", status
);
1027 if (status
& ERR_EN
) {
1028 omap_hsmmc_dbg_report_irq(host
, status
);
1030 if (status
& (CTO_EN
| CCRC_EN
))
1032 if (status
& (CTO_EN
| DTO_EN
))
1033 hsmmc_command_incomplete(host
, -ETIMEDOUT
, end_cmd
);
1034 else if (status
& (CCRC_EN
| DCRC_EN
))
1035 hsmmc_command_incomplete(host
, -EILSEQ
, end_cmd
);
1037 if (host
->data
|| host
->response_busy
) {
1038 end_trans
= !end_cmd
;
1039 host
->response_busy
= 0;
1043 if (end_cmd
|| ((status
& CC_EN
) && host
->cmd
))
1044 omap_hsmmc_cmd_done(host
, host
->cmd
);
1045 if ((end_trans
|| (status
& TC_EN
)) && host
->mrq
)
1046 omap_hsmmc_xfer_done(host
, data
);
1050 * MMC controller IRQ handler
1052 static irqreturn_t
omap_hsmmc_irq(int irq
, void *dev_id
)
1054 struct omap_hsmmc_host
*host
= dev_id
;
1057 status
= OMAP_HSMMC_READ(host
->base
, STAT
);
1058 while (status
& INT_EN_MASK
&& host
->req_in_progress
) {
1059 omap_hsmmc_do_irq(host
, status
);
1061 /* Flush posted write */
1062 OMAP_HSMMC_WRITE(host
->base
, STAT
, status
);
1063 status
= OMAP_HSMMC_READ(host
->base
, STAT
);
1069 static void set_sd_bus_power(struct omap_hsmmc_host
*host
)
1073 OMAP_HSMMC_WRITE(host
->base
, HCTL
,
1074 OMAP_HSMMC_READ(host
->base
, HCTL
) | SDBP
);
1075 for (i
= 0; i
< loops_per_jiffy
; i
++) {
1076 if (OMAP_HSMMC_READ(host
->base
, HCTL
) & SDBP
)
1083 * Switch MMC interface voltage ... only relevant for MMC1.
1085 * MMC2 and MMC3 use fixed 1.8V levels, and maybe a transceiver.
1086 * The MMC2 transceiver controls are used instead of DAT4..DAT7.
1087 * Some chips, like eMMC ones, use internal transceivers.
1089 static int omap_hsmmc_switch_opcond(struct omap_hsmmc_host
*host
, int vdd
)
1094 /* Disable the clocks */
1095 pm_runtime_put_sync(host
->dev
);
1097 clk_disable_unprepare(host
->dbclk
);
1099 /* Turn the power off */
1100 ret
= mmc_slot(host
).set_power(host
->dev
, host
->slot_id
, 0, 0);
1102 /* Turn the power ON with given VDD 1.8 or 3.0v */
1104 ret
= mmc_slot(host
).set_power(host
->dev
, host
->slot_id
, 1,
1106 pm_runtime_get_sync(host
->dev
);
1108 clk_prepare_enable(host
->dbclk
);
1113 OMAP_HSMMC_WRITE(host
->base
, HCTL
,
1114 OMAP_HSMMC_READ(host
->base
, HCTL
) & SDVSCLR
);
1115 reg_val
= OMAP_HSMMC_READ(host
->base
, HCTL
);
1118 * If a MMC dual voltage card is detected, the set_ios fn calls
1119 * this fn with VDD bit set for 1.8V. Upon card removal from the
1120 * slot, omap_hsmmc_set_ios sets the VDD back to 3V on MMC_POWER_OFF.
1122 * Cope with a bit of slop in the range ... per data sheets:
1123 * - "1.8V" for vdds_mmc1/vdds_mmc1a can be up to 2.45V max,
1124 * but recommended values are 1.71V to 1.89V
1125 * - "3.0V" for vdds_mmc1/vdds_mmc1a can be up to 3.5V max,
1126 * but recommended values are 2.7V to 3.3V
1128 * Board setup code shouldn't permit anything very out-of-range.
1129 * TWL4030-family VMMC1 and VSIM regulators are fine (avoiding the
1130 * middle range) but VSIM can't power DAT4..DAT7 at more than 3V.
1132 if ((1 << vdd
) <= MMC_VDD_23_24
)
1137 OMAP_HSMMC_WRITE(host
->base
, HCTL
, reg_val
);
1138 set_sd_bus_power(host
);
1142 dev_err(mmc_dev(host
->mmc
), "Unable to switch operating voltage\n");
1146 /* Protect the card while the cover is open */
1147 static void omap_hsmmc_protect_card(struct omap_hsmmc_host
*host
)
1149 if (!mmc_slot(host
).get_cover_state
)
1152 host
->reqs_blocked
= 0;
1153 if (mmc_slot(host
).get_cover_state(host
->dev
, host
->slot_id
)) {
1154 if (host
->protect_card
) {
1155 dev_info(host
->dev
, "%s: cover is closed, "
1156 "card is now accessible\n",
1157 mmc_hostname(host
->mmc
));
1158 host
->protect_card
= 0;
1161 if (!host
->protect_card
) {
1162 dev_info(host
->dev
, "%s: cover is open, "
1163 "card is now inaccessible\n",
1164 mmc_hostname(host
->mmc
));
1165 host
->protect_card
= 1;
1171 * irq handler to notify the core about card insertion/removal
1173 static irqreturn_t
omap_hsmmc_detect(int irq
, void *dev_id
)
1175 struct omap_hsmmc_host
*host
= dev_id
;
1176 struct omap_mmc_slot_data
*slot
= &mmc_slot(host
);
1179 if (host
->suspended
)
1182 sysfs_notify(&host
->mmc
->class_dev
.kobj
, NULL
, "cover_switch");
1184 if (slot
->card_detect
)
1185 carddetect
= slot
->card_detect(host
->dev
, host
->slot_id
);
1187 omap_hsmmc_protect_card(host
);
1188 carddetect
= -ENOSYS
;
1192 mmc_detect_change(host
->mmc
, (HZ
* 200) / 1000);
1194 mmc_detect_change(host
->mmc
, (HZ
* 50) / 1000);
1198 static void omap_hsmmc_dma_callback(void *param
)
1200 struct omap_hsmmc_host
*host
= param
;
1201 struct dma_chan
*chan
;
1202 struct mmc_data
*data
;
1203 int req_in_progress
;
1205 spin_lock_irq(&host
->irq_lock
);
1206 if (host
->dma_ch
< 0) {
1207 spin_unlock_irq(&host
->irq_lock
);
1211 data
= host
->mrq
->data
;
1212 chan
= omap_hsmmc_get_dma_chan(host
, data
);
1213 if (!data
->host_cookie
)
1214 dma_unmap_sg(chan
->device
->dev
,
1215 data
->sg
, data
->sg_len
,
1216 omap_hsmmc_get_dma_dir(host
, data
));
1218 req_in_progress
= host
->req_in_progress
;
1220 spin_unlock_irq(&host
->irq_lock
);
1222 /* If DMA has finished after TC, complete the request */
1223 if (!req_in_progress
) {
1224 struct mmc_request
*mrq
= host
->mrq
;
1227 mmc_request_done(host
->mmc
, mrq
);
1231 static int omap_hsmmc_pre_dma_transfer(struct omap_hsmmc_host
*host
,
1232 struct mmc_data
*data
,
1233 struct omap_hsmmc_next
*next
,
1234 struct dma_chan
*chan
)
1238 if (!next
&& data
->host_cookie
&&
1239 data
->host_cookie
!= host
->next_data
.cookie
) {
1240 dev_warn(host
->dev
, "[%s] invalid cookie: data->host_cookie %d"
1241 " host->next_data.cookie %d\n",
1242 __func__
, data
->host_cookie
, host
->next_data
.cookie
);
1243 data
->host_cookie
= 0;
1246 /* Check if next job is already prepared */
1248 (!next
&& data
->host_cookie
!= host
->next_data
.cookie
)) {
1249 dma_len
= dma_map_sg(chan
->device
->dev
, data
->sg
, data
->sg_len
,
1250 omap_hsmmc_get_dma_dir(host
, data
));
1253 dma_len
= host
->next_data
.dma_len
;
1254 host
->next_data
.dma_len
= 0;
1262 next
->dma_len
= dma_len
;
1263 data
->host_cookie
= ++next
->cookie
< 0 ? 1 : next
->cookie
;
1265 host
->dma_len
= dma_len
;
1271 * Routine to configure and start DMA for the MMC card
1273 static int omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host
*host
,
1274 struct mmc_request
*req
)
1276 struct dma_slave_config cfg
;
1277 struct dma_async_tx_descriptor
*tx
;
1279 struct mmc_data
*data
= req
->data
;
1280 struct dma_chan
*chan
;
1282 /* Sanity check: all the SG entries must be aligned by block size. */
1283 for (i
= 0; i
< data
->sg_len
; i
++) {
1284 struct scatterlist
*sgl
;
1287 if (sgl
->length
% data
->blksz
)
1290 if ((data
->blksz
% 4) != 0)
1291 /* REVISIT: The MMC buffer increments only when MSB is written.
1292 * Return error for blksz which is non multiple of four.
1296 BUG_ON(host
->dma_ch
!= -1);
1298 chan
= omap_hsmmc_get_dma_chan(host
, data
);
1300 cfg
.src_addr
= host
->mapbase
+ OMAP_HSMMC_DATA
;
1301 cfg
.dst_addr
= host
->mapbase
+ OMAP_HSMMC_DATA
;
1302 cfg
.src_addr_width
= DMA_SLAVE_BUSWIDTH_4_BYTES
;
1303 cfg
.dst_addr_width
= DMA_SLAVE_BUSWIDTH_4_BYTES
;
1304 cfg
.src_maxburst
= data
->blksz
/ 4;
1305 cfg
.dst_maxburst
= data
->blksz
/ 4;
1307 ret
= dmaengine_slave_config(chan
, &cfg
);
1311 ret
= omap_hsmmc_pre_dma_transfer(host
, data
, NULL
, chan
);
1315 tx
= dmaengine_prep_slave_sg(chan
, data
->sg
, data
->sg_len
,
1316 data
->flags
& MMC_DATA_WRITE
? DMA_MEM_TO_DEV
: DMA_DEV_TO_MEM
,
1317 DMA_PREP_INTERRUPT
| DMA_CTRL_ACK
);
1319 dev_err(mmc_dev(host
->mmc
), "prep_slave_sg() failed\n");
1320 /* FIXME: cleanup */
1324 tx
->callback
= omap_hsmmc_dma_callback
;
1325 tx
->callback_param
= host
;
1328 dmaengine_submit(tx
);
1332 dma_async_issue_pending(chan
);
1337 static void set_data_timeout(struct omap_hsmmc_host
*host
,
1338 unsigned int timeout_ns
,
1339 unsigned int timeout_clks
)
1341 unsigned int timeout
, cycle_ns
;
1342 uint32_t reg
, clkd
, dto
= 0;
1344 reg
= OMAP_HSMMC_READ(host
->base
, SYSCTL
);
1345 clkd
= (reg
& CLKD_MASK
) >> CLKD_SHIFT
;
1349 cycle_ns
= 1000000000 / (clk_get_rate(host
->fclk
) / clkd
);
1350 timeout
= timeout_ns
/ cycle_ns
;
1351 timeout
+= timeout_clks
;
1353 while ((timeout
& 0x80000000) == 0) {
1370 reg
|= dto
<< DTO_SHIFT
;
1371 OMAP_HSMMC_WRITE(host
->base
, SYSCTL
, reg
);
1375 * Configure block length for MMC/SD cards and initiate the transfer.
1378 omap_hsmmc_prepare_data(struct omap_hsmmc_host
*host
, struct mmc_request
*req
)
1381 host
->data
= req
->data
;
1383 if (req
->data
== NULL
) {
1384 OMAP_HSMMC_WRITE(host
->base
, BLK
, 0);
1386 * Set an arbitrary 100ms data timeout for commands with
1389 if (req
->cmd
->flags
& MMC_RSP_BUSY
)
1390 set_data_timeout(host
, 100000000U, 0);
1394 OMAP_HSMMC_WRITE(host
->base
, BLK
, (req
->data
->blksz
)
1395 | (req
->data
->blocks
<< 16));
1396 set_data_timeout(host
, req
->data
->timeout_ns
, req
->data
->timeout_clks
);
1398 if (host
->use_dma
) {
1399 ret
= omap_hsmmc_start_dma_transfer(host
, req
);
1401 dev_err(mmc_dev(host
->mmc
), "MMC start dma failure\n");
1408 static void omap_hsmmc_post_req(struct mmc_host
*mmc
, struct mmc_request
*mrq
,
1411 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1412 struct mmc_data
*data
= mrq
->data
;
1414 if (host
->use_dma
&& data
->host_cookie
) {
1415 struct dma_chan
*c
= omap_hsmmc_get_dma_chan(host
, data
);
1417 dma_unmap_sg(c
->device
->dev
, data
->sg
, data
->sg_len
,
1418 omap_hsmmc_get_dma_dir(host
, data
));
1419 data
->host_cookie
= 0;
1423 static void omap_hsmmc_pre_req(struct mmc_host
*mmc
, struct mmc_request
*mrq
,
1426 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1428 if (mrq
->data
->host_cookie
) {
1429 mrq
->data
->host_cookie
= 0;
1433 if (host
->use_dma
) {
1434 struct dma_chan
*c
= omap_hsmmc_get_dma_chan(host
, mrq
->data
);
1436 if (omap_hsmmc_pre_dma_transfer(host
, mrq
->data
,
1437 &host
->next_data
, c
))
1438 mrq
->data
->host_cookie
= 0;
1443 * Request function. for read/write operation
1445 static void omap_hsmmc_request(struct mmc_host
*mmc
, struct mmc_request
*req
)
1447 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1450 BUG_ON(host
->req_in_progress
);
1451 BUG_ON(host
->dma_ch
!= -1);
1452 if (host
->protect_card
) {
1453 if (host
->reqs_blocked
< 3) {
1455 * Ensure the controller is left in a consistent
1456 * state by resetting the command and data state
1459 omap_hsmmc_reset_controller_fsm(host
, SRD
);
1460 omap_hsmmc_reset_controller_fsm(host
, SRC
);
1461 host
->reqs_blocked
+= 1;
1463 req
->cmd
->error
= -EBADF
;
1465 req
->data
->error
= -EBADF
;
1466 req
->cmd
->retries
= 0;
1467 mmc_request_done(mmc
, req
);
1469 } else if (host
->reqs_blocked
)
1470 host
->reqs_blocked
= 0;
1471 WARN_ON(host
->mrq
!= NULL
);
1473 err
= omap_hsmmc_prepare_data(host
, req
);
1475 req
->cmd
->error
= err
;
1477 req
->data
->error
= err
;
1479 mmc_request_done(mmc
, req
);
1483 omap_hsmmc_start_command(host
, req
->cmd
, req
->data
);
1486 /* Routine to configure clock values. Exposed API to core */
1487 static void omap_hsmmc_set_ios(struct mmc_host
*mmc
, struct mmc_ios
*ios
)
1489 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1490 int do_send_init_stream
= 0;
1492 pm_runtime_get_sync(host
->dev
);
1494 if (ios
->power_mode
!= host
->power_mode
) {
1495 switch (ios
->power_mode
) {
1497 mmc_slot(host
).set_power(host
->dev
, host
->slot_id
,
1501 mmc_slot(host
).set_power(host
->dev
, host
->slot_id
,
1505 do_send_init_stream
= 1;
1508 host
->power_mode
= ios
->power_mode
;
1511 /* FIXME: set registers based only on changes to ios */
1513 omap_hsmmc_set_bus_width(host
);
1515 if (host
->pdata
->controller_flags
& OMAP_HSMMC_SUPPORTS_DUAL_VOLT
) {
1516 /* Only MMC1 can interface at 3V without some flavor
1517 * of external transceiver; but they all handle 1.8V.
1519 if ((OMAP_HSMMC_READ(host
->base
, HCTL
) & SDVSDET
) &&
1520 (ios
->vdd
== DUAL_VOLT_OCR_BIT
) &&
1522 * With pbias cell programming missing, this
1523 * can't be allowed when booting with device
1526 !host
->dev
->of_node
) {
1528 * The mmc_select_voltage fn of the core does
1529 * not seem to set the power_mode to
1530 * MMC_POWER_UP upon recalculating the voltage.
1533 if (omap_hsmmc_switch_opcond(host
, ios
->vdd
) != 0)
1534 dev_dbg(mmc_dev(host
->mmc
),
1535 "Switch operation failed\n");
1539 omap_hsmmc_set_clock(host
);
1541 if (do_send_init_stream
)
1542 send_init_stream(host
);
1544 omap_hsmmc_set_bus_mode(host
);
1546 pm_runtime_put_autosuspend(host
->dev
);
1549 static int omap_hsmmc_get_cd(struct mmc_host
*mmc
)
1551 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1553 if (!mmc_slot(host
).card_detect
)
1555 return mmc_slot(host
).card_detect(host
->dev
, host
->slot_id
);
1558 static int omap_hsmmc_get_ro(struct mmc_host
*mmc
)
1560 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1562 if (!mmc_slot(host
).get_ro
)
1564 return mmc_slot(host
).get_ro(host
->dev
, 0);
1567 static void omap_hsmmc_init_card(struct mmc_host
*mmc
, struct mmc_card
*card
)
1569 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1571 if (mmc_slot(host
).init_card
)
1572 mmc_slot(host
).init_card(card
);
1575 static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host
*host
)
1577 u32 hctl
, capa
, value
;
1579 /* Only MMC1 supports 3.0V */
1580 if (host
->pdata
->controller_flags
& OMAP_HSMMC_SUPPORTS_DUAL_VOLT
) {
1588 value
= OMAP_HSMMC_READ(host
->base
, HCTL
) & ~SDVS_MASK
;
1589 OMAP_HSMMC_WRITE(host
->base
, HCTL
, value
| hctl
);
1591 value
= OMAP_HSMMC_READ(host
->base
, CAPA
);
1592 OMAP_HSMMC_WRITE(host
->base
, CAPA
, value
| capa
);
1594 /* Set SD bus power bit */
1595 set_sd_bus_power(host
);
1598 static int omap_hsmmc_enable_fclk(struct mmc_host
*mmc
)
1600 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1602 pm_runtime_get_sync(host
->dev
);
1607 static int omap_hsmmc_disable_fclk(struct mmc_host
*mmc
)
1609 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1611 pm_runtime_mark_last_busy(host
->dev
);
1612 pm_runtime_put_autosuspend(host
->dev
);
1617 static const struct mmc_host_ops omap_hsmmc_ops
= {
1618 .enable
= omap_hsmmc_enable_fclk
,
1619 .disable
= omap_hsmmc_disable_fclk
,
1620 .post_req
= omap_hsmmc_post_req
,
1621 .pre_req
= omap_hsmmc_pre_req
,
1622 .request
= omap_hsmmc_request
,
1623 .set_ios
= omap_hsmmc_set_ios
,
1624 .get_cd
= omap_hsmmc_get_cd
,
1625 .get_ro
= omap_hsmmc_get_ro
,
1626 .init_card
= omap_hsmmc_init_card
,
1627 /* NYET -- enable_sdio_irq */
1630 #ifdef CONFIG_DEBUG_FS
1632 static int omap_hsmmc_regs_show(struct seq_file
*s
, void *data
)
1634 struct mmc_host
*mmc
= s
->private;
1635 struct omap_hsmmc_host
*host
= mmc_priv(mmc
);
1636 int context_loss
= 0;
1638 if (host
->pdata
->get_context_loss_count
)
1639 context_loss
= host
->pdata
->get_context_loss_count(host
->dev
);
1641 seq_printf(s
, "mmc%d:\n ctx_loss:\t%d:%d\n\nregs:\n",
1642 mmc
->index
, host
->context_loss
, context_loss
);
1644 if (host
->suspended
) {
1645 seq_printf(s
, "host suspended, can't read registers\n");
1649 pm_runtime_get_sync(host
->dev
);
1651 seq_printf(s
, "CON:\t\t0x%08x\n",
1652 OMAP_HSMMC_READ(host
->base
, CON
));
1653 seq_printf(s
, "HCTL:\t\t0x%08x\n",
1654 OMAP_HSMMC_READ(host
->base
, HCTL
));
1655 seq_printf(s
, "SYSCTL:\t\t0x%08x\n",
1656 OMAP_HSMMC_READ(host
->base
, SYSCTL
));
1657 seq_printf(s
, "IE:\t\t0x%08x\n",
1658 OMAP_HSMMC_READ(host
->base
, IE
));
1659 seq_printf(s
, "ISE:\t\t0x%08x\n",
1660 OMAP_HSMMC_READ(host
->base
, ISE
));
1661 seq_printf(s
, "CAPA:\t\t0x%08x\n",
1662 OMAP_HSMMC_READ(host
->base
, CAPA
));
1664 pm_runtime_mark_last_busy(host
->dev
);
1665 pm_runtime_put_autosuspend(host
->dev
);
1670 static int omap_hsmmc_regs_open(struct inode
*inode
, struct file
*file
)
1672 return single_open(file
, omap_hsmmc_regs_show
, inode
->i_private
);
1675 static const struct file_operations mmc_regs_fops
= {
1676 .open
= omap_hsmmc_regs_open
,
1678 .llseek
= seq_lseek
,
1679 .release
= single_release
,
1682 static void omap_hsmmc_debugfs(struct mmc_host
*mmc
)
1684 if (mmc
->debugfs_root
)
1685 debugfs_create_file("regs", S_IRUSR
, mmc
->debugfs_root
,
1686 mmc
, &mmc_regs_fops
);
1691 static void omap_hsmmc_debugfs(struct mmc_host
*mmc
)
1698 static u16 omap4_reg_offset
= 0x100;
1700 static const struct of_device_id omap_mmc_of_match
[] = {
1702 .compatible
= "ti,omap2-hsmmc",
1705 .compatible
= "ti,omap3-hsmmc",
1708 .compatible
= "ti,omap4-hsmmc",
1709 .data
= &omap4_reg_offset
,
1713 MODULE_DEVICE_TABLE(of
, omap_mmc_of_match
);
1715 static struct omap_mmc_platform_data
*of_get_hsmmc_pdata(struct device
*dev
)
1717 struct omap_mmc_platform_data
*pdata
;
1718 struct device_node
*np
= dev
->of_node
;
1719 u32 bus_width
, max_freq
;
1721 pdata
= devm_kzalloc(dev
, sizeof(*pdata
), GFP_KERNEL
);
1723 return NULL
; /* out of memory */
1725 if (of_find_property(np
, "ti,dual-volt", NULL
))
1726 pdata
->controller_flags
|= OMAP_HSMMC_SUPPORTS_DUAL_VOLT
;
1728 /* This driver only supports 1 slot */
1729 pdata
->nr_slots
= 1;
1730 pdata
->slots
[0].switch_pin
= of_get_named_gpio(np
, "cd-gpios", 0);
1731 pdata
->slots
[0].gpio_wp
= of_get_named_gpio(np
, "wp-gpios", 0);
1733 if (of_find_property(np
, "ti,non-removable", NULL
)) {
1734 pdata
->slots
[0].nonremovable
= true;
1735 pdata
->slots
[0].no_regulator_off_init
= true;
1737 of_property_read_u32(np
, "bus-width", &bus_width
);
1739 pdata
->slots
[0].caps
|= MMC_CAP_4_BIT_DATA
;
1740 else if (bus_width
== 8)
1741 pdata
->slots
[0].caps
|= MMC_CAP_8_BIT_DATA
;
1743 if (of_find_property(np
, "ti,needs-special-reset", NULL
))
1744 pdata
->slots
[0].features
|= HSMMC_HAS_UPDATED_RESET
;
1746 if (!of_property_read_u32(np
, "max-frequency", &max_freq
))
1747 pdata
->max_freq
= max_freq
;
1749 if (of_find_property(np
, "ti,needs-special-hs-handling", NULL
))
1750 pdata
->slots
[0].features
|= HSMMC_HAS_HSPE_SUPPORT
;
1755 static inline struct omap_mmc_platform_data
1756 *of_get_hsmmc_pdata(struct device
*dev
)
1762 static int omap_hsmmc_probe(struct platform_device
*pdev
)
1764 struct omap_mmc_platform_data
*pdata
= pdev
->dev
.platform_data
;
1765 struct mmc_host
*mmc
;
1766 struct omap_hsmmc_host
*host
= NULL
;
1767 struct resource
*res
;
1769 const struct of_device_id
*match
;
1770 dma_cap_mask_t mask
;
1771 unsigned tx_req
, rx_req
;
1772 struct pinctrl
*pinctrl
;
1774 match
= of_match_device(of_match_ptr(omap_mmc_of_match
), &pdev
->dev
);
1776 pdata
= of_get_hsmmc_pdata(&pdev
->dev
);
1778 const u16
*offsetp
= match
->data
;
1779 pdata
->reg_offset
= *offsetp
;
1783 if (pdata
== NULL
) {
1784 dev_err(&pdev
->dev
, "Platform Data is missing\n");
1788 if (pdata
->nr_slots
== 0) {
1789 dev_err(&pdev
->dev
, "No Slots\n");
1793 res
= platform_get_resource(pdev
, IORESOURCE_MEM
, 0);
1794 irq
= platform_get_irq(pdev
, 0);
1795 if (res
== NULL
|| irq
< 0)
1798 res
= request_mem_region(res
->start
, resource_size(res
), pdev
->name
);
1802 ret
= omap_hsmmc_gpio_init(pdata
);
1806 mmc
= mmc_alloc_host(sizeof(struct omap_hsmmc_host
), &pdev
->dev
);
1812 host
= mmc_priv(mmc
);
1814 host
->pdata
= pdata
;
1815 host
->dev
= &pdev
->dev
;
1820 host
->mapbase
= res
->start
+ pdata
->reg_offset
;
1821 host
->base
= ioremap(host
->mapbase
, SZ_4K
);
1822 host
->power_mode
= MMC_POWER_OFF
;
1823 host
->next_data
.cookie
= 1;
1825 platform_set_drvdata(pdev
, host
);
1827 mmc
->ops
= &omap_hsmmc_ops
;
1830 * If regulator_disable can only put vcc_aux to sleep then there is
1833 if (mmc_slot(host
).vcc_aux_disable_is_sleep
)
1834 mmc_slot(host
).no_off
= 1;
1836 mmc
->f_min
= OMAP_MMC_MIN_CLOCK
;
1838 if (pdata
->max_freq
> 0)
1839 mmc
->f_max
= pdata
->max_freq
;
1841 mmc
->f_max
= OMAP_MMC_MAX_CLOCK
;
1843 spin_lock_init(&host
->irq_lock
);
1845 host
->fclk
= clk_get(&pdev
->dev
, "fck");
1846 if (IS_ERR(host
->fclk
)) {
1847 ret
= PTR_ERR(host
->fclk
);
1852 if (host
->pdata
->controller_flags
& OMAP_HSMMC_BROKEN_MULTIBLOCK_READ
) {
1853 dev_info(&pdev
->dev
, "multiblock reads disabled due to 35xx erratum 2.1.1.128; MMC read performance may suffer\n");
1854 mmc
->caps2
|= MMC_CAP2_NO_MULTI_READ
;
1857 pm_runtime_enable(host
->dev
);
1858 pm_runtime_get_sync(host
->dev
);
1859 pm_runtime_set_autosuspend_delay(host
->dev
, MMC_AUTOSUSPEND_DELAY
);
1860 pm_runtime_use_autosuspend(host
->dev
);
1862 omap_hsmmc_context_save(host
);
1864 host
->dbclk
= clk_get(&pdev
->dev
, "mmchsdb_fck");
1866 * MMC can still work without debounce clock.
1868 if (IS_ERR(host
->dbclk
)) {
1870 } else if (clk_prepare_enable(host
->dbclk
) != 0) {
1871 dev_warn(mmc_dev(host
->mmc
), "Failed to enable debounce clk\n");
1872 clk_put(host
->dbclk
);
1876 /* Since we do only SG emulation, we can have as many segs
1878 mmc
->max_segs
= 1024;
1880 mmc
->max_blk_size
= 512; /* Block Length at max can be 1024 */
1881 mmc
->max_blk_count
= 0xFFFF; /* No. of Blocks is 16 bits */
1882 mmc
->max_req_size
= mmc
->max_blk_size
* mmc
->max_blk_count
;
1883 mmc
->max_seg_size
= mmc
->max_req_size
;
1885 mmc
->caps
|= MMC_CAP_MMC_HIGHSPEED
| MMC_CAP_SD_HIGHSPEED
|
1886 MMC_CAP_WAIT_WHILE_BUSY
| MMC_CAP_ERASE
;
1888 mmc
->caps
|= mmc_slot(host
).caps
;
1889 if (mmc
->caps
& MMC_CAP_8_BIT_DATA
)
1890 mmc
->caps
|= MMC_CAP_4_BIT_DATA
;
1892 if (mmc_slot(host
).nonremovable
)
1893 mmc
->caps
|= MMC_CAP_NONREMOVABLE
;
1895 mmc
->pm_caps
= mmc_slot(host
).pm_caps
;
1897 omap_hsmmc_conf_bus_power(host
);
1899 res
= platform_get_resource_byname(pdev
, IORESOURCE_DMA
, "tx");
1901 dev_err(mmc_dev(host
->mmc
), "cannot get DMA TX channel\n");
1905 tx_req
= res
->start
;
1907 res
= platform_get_resource_byname(pdev
, IORESOURCE_DMA
, "rx");
1909 dev_err(mmc_dev(host
->mmc
), "cannot get DMA RX channel\n");
1913 rx_req
= res
->start
;
1916 dma_cap_set(DMA_SLAVE
, mask
);
1918 host
->rx_chan
= dma_request_channel(mask
, omap_dma_filter_fn
, &rx_req
);
1919 if (!host
->rx_chan
) {
1920 dev_err(mmc_dev(host
->mmc
), "unable to obtain RX DMA engine channel %u\n", rx_req
);
1925 host
->tx_chan
= dma_request_channel(mask
, omap_dma_filter_fn
, &tx_req
);
1926 if (!host
->tx_chan
) {
1927 dev_err(mmc_dev(host
->mmc
), "unable to obtain TX DMA engine channel %u\n", tx_req
);
1932 /* Request IRQ for MMC operations */
1933 ret
= request_irq(host
->irq
, omap_hsmmc_irq
, 0,
1934 mmc_hostname(mmc
), host
);
1936 dev_err(mmc_dev(host
->mmc
), "Unable to grab HSMMC IRQ\n");
1940 if (pdata
->init
!= NULL
) {
1941 if (pdata
->init(&pdev
->dev
) != 0) {
1942 dev_err(mmc_dev(host
->mmc
),
1943 "Unable to configure MMC IRQs\n");
1944 goto err_irq_cd_init
;
1948 if (omap_hsmmc_have_reg() && !mmc_slot(host
).set_power
) {
1949 ret
= omap_hsmmc_reg_get(host
);
1955 mmc
->ocr_avail
= mmc_slot(host
).ocr_mask
;
1957 /* Request IRQ for card detect */
1958 if ((mmc_slot(host
).card_detect_irq
)) {
1959 ret
= request_threaded_irq(mmc_slot(host
).card_detect_irq
,
1962 IRQF_TRIGGER_RISING
| IRQF_TRIGGER_FALLING
| IRQF_ONESHOT
,
1963 mmc_hostname(mmc
), host
);
1965 dev_err(mmc_dev(host
->mmc
),
1966 "Unable to grab MMC CD IRQ\n");
1969 pdata
->suspend
= omap_hsmmc_suspend_cdirq
;
1970 pdata
->resume
= omap_hsmmc_resume_cdirq
;
1973 omap_hsmmc_disable_irq(host
);
1975 pinctrl
= devm_pinctrl_get_select_default(&pdev
->dev
);
1976 if (IS_ERR(pinctrl
))
1977 dev_warn(&pdev
->dev
,
1978 "pins are not configured from the driver\n");
1980 omap_hsmmc_protect_card(host
);
1984 if (mmc_slot(host
).name
!= NULL
) {
1985 ret
= device_create_file(&mmc
->class_dev
, &dev_attr_slot_name
);
1989 if (mmc_slot(host
).card_detect_irq
&& mmc_slot(host
).get_cover_state
) {
1990 ret
= device_create_file(&mmc
->class_dev
,
1991 &dev_attr_cover_switch
);
1996 omap_hsmmc_debugfs(mmc
);
1997 pm_runtime_mark_last_busy(host
->dev
);
1998 pm_runtime_put_autosuspend(host
->dev
);
2003 mmc_remove_host(mmc
);
2004 free_irq(mmc_slot(host
).card_detect_irq
, host
);
2007 omap_hsmmc_reg_put(host
);
2009 if (host
->pdata
->cleanup
)
2010 host
->pdata
->cleanup(&pdev
->dev
);
2012 free_irq(host
->irq
, host
);
2015 dma_release_channel(host
->tx_chan
);
2017 dma_release_channel(host
->rx_chan
);
2018 pm_runtime_put_sync(host
->dev
);
2019 pm_runtime_disable(host
->dev
);
2020 clk_put(host
->fclk
);
2022 clk_disable_unprepare(host
->dbclk
);
2023 clk_put(host
->dbclk
);
2026 iounmap(host
->base
);
2027 platform_set_drvdata(pdev
, NULL
);
2030 omap_hsmmc_gpio_free(pdata
);
2032 res
= platform_get_resource(pdev
, IORESOURCE_MEM
, 0);
2034 release_mem_region(res
->start
, resource_size(res
));
2038 static int omap_hsmmc_remove(struct platform_device
*pdev
)
2040 struct omap_hsmmc_host
*host
= platform_get_drvdata(pdev
);
2041 struct resource
*res
;
2043 pm_runtime_get_sync(host
->dev
);
2044 mmc_remove_host(host
->mmc
);
2046 omap_hsmmc_reg_put(host
);
2047 if (host
->pdata
->cleanup
)
2048 host
->pdata
->cleanup(&pdev
->dev
);
2049 free_irq(host
->irq
, host
);
2050 if (mmc_slot(host
).card_detect_irq
)
2051 free_irq(mmc_slot(host
).card_detect_irq
, host
);
2054 dma_release_channel(host
->tx_chan
);
2056 dma_release_channel(host
->rx_chan
);
2058 pm_runtime_put_sync(host
->dev
);
2059 pm_runtime_disable(host
->dev
);
2060 clk_put(host
->fclk
);
2062 clk_disable_unprepare(host
->dbclk
);
2063 clk_put(host
->dbclk
);
2066 omap_hsmmc_gpio_free(host
->pdata
);
2067 iounmap(host
->base
);
2068 mmc_free_host(host
->mmc
);
2070 res
= platform_get_resource(pdev
, IORESOURCE_MEM
, 0);
2072 release_mem_region(res
->start
, resource_size(res
));
2073 platform_set_drvdata(pdev
, NULL
);
2079 static int omap_hsmmc_prepare(struct device
*dev
)
2081 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
2083 if (host
->pdata
->suspend
)
2084 return host
->pdata
->suspend(dev
, host
->slot_id
);
2089 static void omap_hsmmc_complete(struct device
*dev
)
2091 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
2093 if (host
->pdata
->resume
)
2094 host
->pdata
->resume(dev
, host
->slot_id
);
2098 static int omap_hsmmc_suspend(struct device
*dev
)
2101 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
2106 if (host
&& host
->suspended
)
2109 pm_runtime_get_sync(host
->dev
);
2110 host
->suspended
= 1;
2111 ret
= mmc_suspend_host(host
->mmc
);
2114 host
->suspended
= 0;
2118 if (!(host
->mmc
->pm_flags
& MMC_PM_KEEP_POWER
)) {
2119 omap_hsmmc_disable_irq(host
);
2120 OMAP_HSMMC_WRITE(host
->base
, HCTL
,
2121 OMAP_HSMMC_READ(host
->base
, HCTL
) & ~SDBP
);
2125 clk_disable_unprepare(host
->dbclk
);
2127 pm_runtime_put_sync(host
->dev
);
2131 /* Routine to resume the MMC device */
2132 static int omap_hsmmc_resume(struct device
*dev
)
2135 struct omap_hsmmc_host
*host
= dev_get_drvdata(dev
);
2140 if (host
&& !host
->suspended
)
2143 pm_runtime_get_sync(host
->dev
);
2146 clk_prepare_enable(host
->dbclk
);
2148 if (!(host
->mmc
->pm_flags
& MMC_PM_KEEP_POWER
))
2149 omap_hsmmc_conf_bus_power(host
);
2151 omap_hsmmc_protect_card(host
);
2153 /* Notify the core to resume the host */
2154 ret
= mmc_resume_host(host
->mmc
);
2156 host
->suspended
= 0;
2158 pm_runtime_mark_last_busy(host
->dev
);
2159 pm_runtime_put_autosuspend(host
->dev
);
2166 #define omap_hsmmc_prepare NULL
2167 #define omap_hsmmc_complete NULL
2168 #define omap_hsmmc_suspend NULL
2169 #define omap_hsmmc_resume NULL
2172 static int omap_hsmmc_runtime_suspend(struct device
*dev
)
2174 struct omap_hsmmc_host
*host
;
2176 host
= platform_get_drvdata(to_platform_device(dev
));
2177 omap_hsmmc_context_save(host
);
2178 dev_dbg(dev
, "disabled\n");
2183 static int omap_hsmmc_runtime_resume(struct device
*dev
)
2185 struct omap_hsmmc_host
*host
;
2187 host
= platform_get_drvdata(to_platform_device(dev
));
2188 omap_hsmmc_context_restore(host
);
2189 dev_dbg(dev
, "enabled\n");
2194 static struct dev_pm_ops omap_hsmmc_dev_pm_ops
= {
2195 .suspend
= omap_hsmmc_suspend
,
2196 .resume
= omap_hsmmc_resume
,
2197 .prepare
= omap_hsmmc_prepare
,
2198 .complete
= omap_hsmmc_complete
,
2199 .runtime_suspend
= omap_hsmmc_runtime_suspend
,
2200 .runtime_resume
= omap_hsmmc_runtime_resume
,
2203 static struct platform_driver omap_hsmmc_driver
= {
2204 .probe
= omap_hsmmc_probe
,
2205 .remove
= omap_hsmmc_remove
,
2207 .name
= DRIVER_NAME
,
2208 .owner
= THIS_MODULE
,
2209 .pm
= &omap_hsmmc_dev_pm_ops
,
2210 .of_match_table
= of_match_ptr(omap_mmc_of_match
),
2214 module_platform_driver(omap_hsmmc_driver
);
2215 MODULE_DESCRIPTION("OMAP High Speed Multimedia Card driver");
2216 MODULE_LICENSE("GPL");
2217 MODULE_ALIAS("platform:" DRIVER_NAME
);
2218 MODULE_AUTHOR("Texas Instruments Inc");