drivers/hwmon/thmc50.c

   1 /*
   2  * thmc50.c - Part of lm_sensors, Linux kernel modules for hardware
   3  *            monitoring
   4  * Copyright (C) 2007 Krzysztof Helt <krzysztof.h1@wp.pl>
   5  * Based on 2.4 driver by Frodo Looijaard <frodol@dds.nl> and
   6  * Philip Edelbrock <phil@netroedge.com>
   7  *
   8  * This program is free software; you can redistribute it and/or modify
   9  * it under the terms of the GNU General Public License as published by
  10  * the Free Software Foundation; either version 2 of the License, or
  11  * (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  21  */
  22
  23 #include <linux/module.h>
  24 #include <linux/init.h>
  25 #include <linux/slab.h>
  26 #include <linux/i2c.h>
  27 #include <linux/hwmon.h>
  28 #include <linux/hwmon-sysfs.h>
  29 #include <linux/err.h>
  30 #include <linux/mutex.h>
  31 #include <linux/jiffies.h>
  32
  33 MODULE_LICENSE("GPL");
  34
  35 /* Addresses to scan */
  36 static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
  37
  38 /* Insmod parameters */
  39 enum chips { thmc50, adm1022 };
  40
  41 static unsigned short adm1022_temp3[16];
  42 static unsigned int adm1022_temp3_num;
  43 module_param_array(adm1022_temp3, ushort, &adm1022_temp3_num, 0);
  44 MODULE_PARM_DESC(adm1022_temp3,
  45                  "List of adapter,address pairs to enable 3rd temperature (ADM1022 only)");
  46
  47 /* Many THMC50 constants specified below */
  48
  49 /* The THMC50 registers */
  50 #define THMC50_REG_CONF                         0x40
  51 #define THMC50_REG_COMPANY_ID                   0x3E
  52 #define THMC50_REG_DIE_CODE                     0x3F
  53 #define THMC50_REG_ANALOG_OUT                   0x19
  54 /*
  55  * The mirror status register cannot be used as
  56  * reading it does not clear alarms.
  57  */
  58 #define THMC50_REG_INTR                         0x41
  59
  60 static const u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 };
  61 static const u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C };
  62 static const u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B };
  63 static const u8 THMC50_REG_TEMP_CRITICAL[] = { 0x13, 0x14, 0x14 };
  64 static const u8 THMC50_REG_TEMP_DEFAULT[] = { 0x17, 0x18, 0x18 };
  65
  66 #define THMC50_REG_CONF_nFANOFF                 0x20
  67 #define THMC50_REG_CONF_PROGRAMMED              0x08
  68
  69 /* Each client has this additional data */
  70 struct thmc50_data {
  71         struct device *hwmon_dev;
  72
  73         struct mutex update_lock;
  74         enum chips type;
  75         unsigned long last_updated;     /* In jiffies */
  76         char has_temp3;         /* !=0 if it is ADM1022 in temp3 mode */
  77         char valid;             /* !=0 if following fields are valid */
  78
  79         /* Register values */
  80         s8 temp_input[3];
  81         s8 temp_max[3];
  82         s8 temp_min[3];
  83         s8 temp_critical[3];
  84         u8 analog_out;
  85         u8 alarms;
  86 };
  87
  88 static int thmc50_detect(struct i2c_client *client,
  89                          struct i2c_board_info *info);
  90 static int thmc50_probe(struct i2c_client *client,
  91                         const struct i2c_device_id *id);
  92 static int thmc50_remove(struct i2c_client *client);
  93 static void thmc50_init_client(struct i2c_client *client);
  94 static struct thmc50_data *thmc50_update_device(struct device *dev);
  95
  96 static const struct i2c_device_id thmc50_id[] = {
  97         { "adm1022", adm1022 },
  98         { "thmc50", thmc50 },
  99         { }
 100 };
 101 MODULE_DEVICE_TABLE(i2c, thmc50_id);
 102
 103 static struct i2c_driver thmc50_driver = {
 104         .class = I2C_CLASS_HWMON,
 105         .driver = {
 106                 .name = "thmc50",
 107         },
 108         .probe = thmc50_probe,
 109         .remove = thmc50_remove,
 110         .id_table = thmc50_id,
 111         .detect = thmc50_detect,
 112         .address_list = normal_i2c,
 113 };
 114
 115 static ssize_t show_analog_out(struct device *dev,
 116                                struct device_attribute *attr, char *buf)
 117 {
 118         struct thmc50_data *data = thmc50_update_device(dev);
 119         return sprintf(buf, "%d\n", data->analog_out);
 120 }
 121
 122 static ssize_t set_analog_out(struct device *dev,
 123                               struct device_attribute *attr,
 124                               const char *buf, size_t count)
 125 {
 126         struct i2c_client *client = to_i2c_client(dev);
 127         struct thmc50_data *data = i2c_get_clientdata(client);
 128         int config;
 129         unsigned long tmp;
 130         int err;
 131
 132         err = kstrtoul(buf, 10, &tmp);
 133         if (err)
 134                 return err;
 135
 136         mutex_lock(&data->update_lock);
 137         data->analog_out = clamp_val(tmp, 0, 255);
 138         i2c_smbus_write_byte_data(client, THMC50_REG_ANALOG_OUT,
 139                                   data->analog_out);
 140
 141         config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 142         if (data->analog_out == 0)
 143                 config &= ~THMC50_REG_CONF_nFANOFF;
 144         else
 145                 config |= THMC50_REG_CONF_nFANOFF;
 146         i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config);
 147
 148         mutex_unlock(&data->update_lock);
 149         return count;
 150 }
 151
 152 /* There is only one PWM mode = DC */
 153 static ssize_t show_pwm_mode(struct device *dev, struct device_attribute *attr,
 154                              char *buf)
 155 {
 156         return sprintf(buf, "0\n");
 157 }
 158
 159 /* Temperatures */
 160 static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
 161                          char *buf)
 162 {
 163         int nr = to_sensor_dev_attr(attr)->index;
 164         struct thmc50_data *data = thmc50_update_device(dev);
 165         return sprintf(buf, "%d\n", data->temp_input[nr] * 1000);
 166 }
 167
 168 static ssize_t show_temp_min(struct device *dev, struct device_attribute *attr,
 169                              char *buf)
 170 {
 171         int nr = to_sensor_dev_attr(attr)->index;
 172         struct thmc50_data *data = thmc50_update_device(dev);
 173         return sprintf(buf, "%d\n", data->temp_min[nr] * 1000);
 174 }
 175
 176 static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr,
 177                             const char *buf, size_t count)
 178 {
 179         int nr = to_sensor_dev_attr(attr)->index;
 180         struct i2c_client *client = to_i2c_client(dev);
 181         struct thmc50_data *data = i2c_get_clientdata(client);
 182         long val;
 183         int err;
 184
 185         err = kstrtol(buf, 10, &val);
 186         if (err)
 187                 return err;
 188
 189         mutex_lock(&data->update_lock);
 190         data->temp_min[nr] = clamp_val(val / 1000, -128, 127);
 191         i2c_smbus_write_byte_data(client, THMC50_REG_TEMP_MIN[nr],
 192                                   data->temp_min[nr]);
 193         mutex_unlock(&data->update_lock);
 194         return count;
 195 }
 196
 197 static ssize_t show_temp_max(struct device *dev, struct device_attribute *attr,
 198                              char *buf)
 199 {
 200         int nr = to_sensor_dev_attr(attr)->index;
 201         struct thmc50_data *data = thmc50_update_device(dev);
 202         return sprintf(buf, "%d\n", data->temp_max[nr] * 1000);
 203 }
 204
 205 static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr,
 206                             const char *buf, size_t count)
 207 {
 208         int nr = to_sensor_dev_attr(attr)->index;
 209         struct i2c_client *client = to_i2c_client(dev);
 210         struct thmc50_data *data = i2c_get_clientdata(client);
 211         long val;
 212         int err;
 213
 214         err = kstrtol(buf, 10, &val);
 215         if (err)
 216                 return err;
 217
 218         mutex_lock(&data->update_lock);
 219         data->temp_max[nr] = clamp_val(val / 1000, -128, 127);
 220         i2c_smbus_write_byte_data(client, THMC50_REG_TEMP_MAX[nr],
 221                                   data->temp_max[nr]);
 222         mutex_unlock(&data->update_lock);
 223         return count;
 224 }
 225
 226 static ssize_t show_temp_critical(struct device *dev,
 227                                   struct device_attribute *attr,
 228                                   char *buf)
 229 {
 230         int nr = to_sensor_dev_attr(attr)->index;
 231         struct thmc50_data *data = thmc50_update_device(dev);
 232         return sprintf(buf, "%d\n", data->temp_critical[nr] * 1000);
 233 }
 234
 235 static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
 236                           char *buf)
 237 {
 238         int index = to_sensor_dev_attr(attr)->index;
 239         struct thmc50_data *data = thmc50_update_device(dev);
 240
 241         return sprintf(buf, "%u\n", (data->alarms >> index) & 1);
 242 }
 243
 244 #define temp_reg(offset)                                                \
 245 static SENSOR_DEVICE_ATTR(temp##offset##_input, S_IRUGO, show_temp,     \
 246                         NULL, offset - 1);                              \
 247 static SENSOR_DEVICE_ATTR(temp##offset##_min, S_IRUGO | S_IWUSR,        \
 248                         show_temp_min, set_temp_min, offset - 1);       \
 249 static SENSOR_DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR,        \
 250                         show_temp_max, set_temp_max, offset - 1);       \
 251 static SENSOR_DEVICE_ATTR(temp##offset##_crit, S_IRUGO,                 \
 252                         show_temp_critical, NULL, offset - 1);
 253
 254 temp_reg(1);
 255 temp_reg(2);
 256 temp_reg(3);
 257
 258 static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 0);
 259 static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 5);
 260 static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 1);
 261 static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 7);
 262 static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 2);
 263
 264 static SENSOR_DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, show_analog_out,
 265                           set_analog_out, 0);
 266 static SENSOR_DEVICE_ATTR(pwm1_mode, S_IRUGO, show_pwm_mode, NULL, 0);
 267
 268 static struct attribute *thmc50_attributes[] = {
 269         &sensor_dev_attr_temp1_max.dev_attr.attr,
 270         &sensor_dev_attr_temp1_min.dev_attr.attr,
 271         &sensor_dev_attr_temp1_input.dev_attr.attr,
 272         &sensor_dev_attr_temp1_crit.dev_attr.attr,
 273         &sensor_dev_attr_temp1_alarm.dev_attr.attr,
 274         &sensor_dev_attr_temp2_max.dev_attr.attr,
 275         &sensor_dev_attr_temp2_min.dev_attr.attr,
 276         &sensor_dev_attr_temp2_input.dev_attr.attr,
 277         &sensor_dev_attr_temp2_crit.dev_attr.attr,
 278         &sensor_dev_attr_temp2_alarm.dev_attr.attr,
 279         &sensor_dev_attr_temp2_fault.dev_attr.attr,
 280         &sensor_dev_attr_pwm1.dev_attr.attr,
 281         &sensor_dev_attr_pwm1_mode.dev_attr.attr,
 282         NULL
 283 };
 284
 285 static const struct attribute_group thmc50_group = {
 286         .attrs = thmc50_attributes,
 287 };
 288
 289 /* for ADM1022 3rd temperature mode */
 290 static struct attribute *temp3_attributes[] = {
 291         &sensor_dev_attr_temp3_max.dev_attr.attr,
 292         &sensor_dev_attr_temp3_min.dev_attr.attr,
 293         &sensor_dev_attr_temp3_input.dev_attr.attr,
 294         &sensor_dev_attr_temp3_crit.dev_attr.attr,
 295         &sensor_dev_attr_temp3_alarm.dev_attr.attr,
 296         &sensor_dev_attr_temp3_fault.dev_attr.attr,
 297         NULL
 298 };
 299
 300 static const struct attribute_group temp3_group = {
 301         .attrs = temp3_attributes,
 302 };
 303
 304 /* Return 0 if detection is successful, -ENODEV otherwise */
 305 static int thmc50_detect(struct i2c_client *client,
 306                          struct i2c_board_info *info)
 307 {
 308         unsigned company;
 309         unsigned revision;
 310         unsigned config;
 311         struct i2c_adapter *adapter = client->adapter;
 312         const char *type_name;
 313
 314         if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
 315                 pr_debug("thmc50: detect failed, smbus byte data not supported!\n");
 316                 return -ENODEV;
 317         }
 318
 319         pr_debug("thmc50: Probing for THMC50 at 0x%2X on bus %d\n",
 320                  client->addr, i2c_adapter_id(client->adapter));
 321
 322         company = i2c_smbus_read_byte_data(client, THMC50_REG_COMPANY_ID);
 323         revision = i2c_smbus_read_byte_data(client, THMC50_REG_DIE_CODE);
 324         config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 325         if (revision < 0xc0 || (config & 0x10))
 326                 return -ENODEV;
 327
 328         if (company == 0x41) {
 329                 int id = i2c_adapter_id(client->adapter);
 330                 int i;
 331
 332                 type_name = "adm1022";
 333                 for (i = 0; i + 1 < adm1022_temp3_num; i += 2)
 334                         if (adm1022_temp3[i] == id &&
 335                             adm1022_temp3[i + 1] == client->addr) {
 336                                 /* enable 2nd remote temp */
 337                                 config |= (1 << 7);
 338                                 i2c_smbus_write_byte_data(client,
 339                                                           THMC50_REG_CONF,
 340                                                           config);
 341                                 break;
 342                         }
 343         } else if (company == 0x49) {
 344                 type_name = "thmc50";
 345         } else {
 346                 pr_debug("thmc50: Detection of THMC50/ADM1022 failed\n");
 347                 return -ENODEV;
 348         }
 349
 350         pr_debug("thmc50: Detected %s (version %x, revision %x)\n",
 351                  type_name, (revision >> 4) - 0xc, revision & 0xf);
 352
 353         strlcpy(info->type, type_name, I2C_NAME_SIZE);
 354
 355         return 0;
 356 }
 357
 358 static int thmc50_probe(struct i2c_client *client,
 359                         const struct i2c_device_id *id)
 360 {
 361         struct thmc50_data *data;
 362         int err;
 363
 364         data = devm_kzalloc(&client->dev, sizeof(struct thmc50_data),
 365                             GFP_KERNEL);
 366         if (!data)
 367                 return -ENOMEM;
 368
 369         i2c_set_clientdata(client, data);
 370         data->type = id->driver_data;
 371         mutex_init(&data->update_lock);
 372
 373         thmc50_init_client(client);
 374
 375         /* Register sysfs hooks */
 376         err = sysfs_create_group(&client->dev.kobj, &thmc50_group);
 377         if (err)
 378                 return err;
 379
 380         /* Register ADM1022 sysfs hooks */
 381         if (data->has_temp3) {
 382                 err = sysfs_create_group(&client->dev.kobj, &temp3_group);
 383                 if (err)
 384                         goto exit_remove_sysfs_thmc50;
 385         }
 386
 387         /* Register a new directory entry with module sensors */
 388         data->hwmon_dev = hwmon_device_register(&client->dev);
 389         if (IS_ERR(data->hwmon_dev)) {
 390                 err = PTR_ERR(data->hwmon_dev);
 391                 goto exit_remove_sysfs;
 392         }
 393
 394         return 0;
 395
 396 exit_remove_sysfs:
 397         if (data->has_temp3)
 398                 sysfs_remove_group(&client->dev.kobj, &temp3_group);
 399 exit_remove_sysfs_thmc50:
 400         sysfs_remove_group(&client->dev.kobj, &thmc50_group);
 401         return err;
 402 }
 403
 404 static int thmc50_remove(struct i2c_client *client)
 405 {
 406         struct thmc50_data *data = i2c_get_clientdata(client);
 407
 408         hwmon_device_unregister(data->hwmon_dev);
 409         sysfs_remove_group(&client->dev.kobj, &thmc50_group);
 410         if (data->has_temp3)
 411                 sysfs_remove_group(&client->dev.kobj, &temp3_group);
 412
 413         return 0;
 414 }
 415
 416 static void thmc50_init_client(struct i2c_client *client)
 417 {
 418         struct thmc50_data *data = i2c_get_clientdata(client);
 419         int config;
 420
 421         data->analog_out = i2c_smbus_read_byte_data(client,
 422                                                     THMC50_REG_ANALOG_OUT);
 423         /* set up to at least 1 */
 424         if (data->analog_out == 0) {
 425                 data->analog_out = 1;
 426                 i2c_smbus_write_byte_data(client, THMC50_REG_ANALOG_OUT,
 427                                           data->analog_out);
 428         }
 429         config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 430         config |= 0x1;  /* start the chip if it is in standby mode */
 431         if (data->type == adm1022 && (config & (1 << 7)))
 432                 data->has_temp3 = 1;
 433         i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config);
 434 }
 435
 436 static struct thmc50_data *thmc50_update_device(struct device *dev)
 437 {
 438         struct i2c_client *client = to_i2c_client(dev);
 439         struct thmc50_data *data = i2c_get_clientdata(client);
 440         int timeout = HZ / 5 + (data->type == thmc50 ? HZ : 0);
 441
 442         mutex_lock(&data->update_lock);
 443
 444         if (time_after(jiffies, data->last_updated + timeout)
 445             || !data->valid) {
 446
 447                 int temps = data->has_temp3 ? 3 : 2;
 448                 int i;
 449                 int prog = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 450
 451                 prog &= THMC50_REG_CONF_PROGRAMMED;
 452
 453                 for (i = 0; i < temps; i++) {
 454                         data->temp_input[i] = i2c_smbus_read_byte_data(client,
 455                                                 THMC50_REG_TEMP[i]);
 456                         data->temp_max[i] = i2c_smbus_read_byte_data(client,
 457                                                 THMC50_REG_TEMP_MAX[i]);
 458                         data->temp_min[i] = i2c_smbus_read_byte_data(client,
 459                                                 THMC50_REG_TEMP_MIN[i]);
 460                         data->temp_critical[i] =
 461                                 i2c_smbus_read_byte_data(client,
 462                                         prog ? THMC50_REG_TEMP_CRITICAL[i]
 463                                              : THMC50_REG_TEMP_DEFAULT[i]);
 464                 }
 465                 data->analog_out =
 466                     i2c_smbus_read_byte_data(client, THMC50_REG_ANALOG_OUT);
 467                 data->alarms =
 468                     i2c_smbus_read_byte_data(client, THMC50_REG_INTR);
 469                 data->last_updated = jiffies;
 470                 data->valid = 1;
 471         }
 472
 473         mutex_unlock(&data->update_lock);
 474
 475         return data;
 476 }
 477
 478 module_i2c_driver(thmc50_driver);
 479
 480 MODULE_AUTHOR("Krzysztof Helt <krzysztof.h1@wp.pl>");
 481 MODULE_DESCRIPTION("THMC50 driver");