2 * drivers/mtd/nand_bbt.c
5 * Bad block table support for the NAND driver
7 * Copyright © 2004 Thomas Gleixner (tglx@linutronix.de)
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
15 * When nand_scan_bbt is called, then it tries to find the bad block table
16 * depending on the options in the BBT descriptor(s). If no flash based BBT
17 * (NAND_BBT_USE_FLASH) is specified then the device is scanned for factory
18 * marked good / bad blocks. This information is used to create a memory BBT.
19 * Once a new bad block is discovered then the "factory" information is updated
21 * If a flash based BBT is specified then the function first tries to find the
22 * BBT on flash. If a BBT is found then the contents are read and the memory
23 * based BBT is created. If a mirrored BBT is selected then the mirror is
24 * searched too and the versions are compared. If the mirror has a greater
25 * version number, then the mirror BBT is used to build the memory based BBT.
26 * If the tables are not versioned, then we "or" the bad block information.
27 * If one of the BBTs is out of date or does not exist it is (re)created.
28 * If no BBT exists at all then the device is scanned for factory marked
29 * good / bad blocks and the bad block tables are created.
31 * For manufacturer created BBTs like the one found on M-SYS DOC devices
32 * the BBT is searched and read but never created
34 * The auto generated bad block table is located in the last good blocks
35 * of the device. The table is mirrored, so it can be updated eventually.
36 * The table is marked in the OOB area with an ident pattern and a version
37 * number which indicates which of both tables is more up to date. If the NAND
38 * controller needs the complete OOB area for the ECC information then the
39 * option NAND_BBT_NO_OOB should be used (along with NAND_BBT_USE_FLASH, of
40 * course): it moves the ident pattern and the version byte into the data area
41 * and the OOB area will remain untouched.
43 * The table uses 2 bits per block
45 * 00b: block is factory marked bad
46 * 01b, 10b: block is marked bad due to wear
48 * The memory bad block table uses the following scheme:
50 * 01b: block is marked bad due to wear
51 * 10b: block is reserved (to protect the bbt area)
52 * 11b: block is factory marked bad
54 * Multichip devices like DOC store the bad block info per floor.
56 * Following assumptions are made:
57 * - bbts start at a page boundary, if autolocated on a block boundary
58 * - the space necessary for a bbt in FLASH does not exceed a block boundary
62 #include <linux/slab.h>
63 #include <linux/types.h>
64 #include <linux/mtd/mtd.h>
65 #include <linux/mtd/bbm.h>
66 #include <linux/mtd/nand.h>
67 #include <linux/mtd/nand_ecc.h>
68 #include <linux/bitops.h>
69 #include <linux/delay.h>
70 #include <linux/vmalloc.h>
71 #include <linux/export.h>
72 #include <linux/string.h>
74 #define BBT_BLOCK_GOOD 0x00
75 #define BBT_BLOCK_WORN 0x01
76 #define BBT_BLOCK_RESERVED 0x02
77 #define BBT_BLOCK_FACTORY_BAD 0x03
79 #define BBT_ENTRY_MASK 0x03
80 #define BBT_ENTRY_SHIFT 2
82 static int nand_update_bbt(struct mtd_info
*mtd
, loff_t offs
);
84 static inline uint8_t bbt_get_entry(struct nand_chip
*chip
, int block
)
86 uint8_t entry
= chip
->bbt
[block
>> BBT_ENTRY_SHIFT
];
87 entry
>>= (block
& BBT_ENTRY_MASK
) * 2;
88 return entry
& BBT_ENTRY_MASK
;
91 static inline void bbt_mark_entry(struct nand_chip
*chip
, int block
,
94 uint8_t msk
= (mark
& BBT_ENTRY_MASK
) << ((block
& BBT_ENTRY_MASK
) * 2);
95 chip
->bbt
[block
>> BBT_ENTRY_SHIFT
] |= msk
;
98 static int check_pattern_no_oob(uint8_t *buf
, struct nand_bbt_descr
*td
)
100 if (memcmp(buf
, td
->pattern
, td
->len
))
106 * check_pattern - [GENERIC] check if a pattern is in the buffer
107 * @buf: the buffer to search
108 * @len: the length of buffer to search
109 * @paglen: the pagelength
110 * @td: search pattern descriptor
112 * Check for a pattern at the given place. Used to search bad block tables and
113 * good / bad block identifiers.
115 static int check_pattern(uint8_t *buf
, int len
, int paglen
, struct nand_bbt_descr
*td
)
117 if (td
->options
& NAND_BBT_NO_OOB
)
118 return check_pattern_no_oob(buf
, td
);
120 /* Compare the pattern */
121 if (memcmp(buf
+ paglen
+ td
->offs
, td
->pattern
, td
->len
))
128 * check_short_pattern - [GENERIC] check if a pattern is in the buffer
129 * @buf: the buffer to search
130 * @td: search pattern descriptor
132 * Check for a pattern at the given place. Used to search bad block tables and
133 * good / bad block identifiers. Same as check_pattern, but no optional empty
136 static int check_short_pattern(uint8_t *buf
, struct nand_bbt_descr
*td
)
138 /* Compare the pattern */
139 if (memcmp(buf
+ td
->offs
, td
->pattern
, td
->len
))
145 * add_marker_len - compute the length of the marker in data area
146 * @td: BBT descriptor used for computation
148 * The length will be 0 if the marker is located in OOB area.
150 static u32
add_marker_len(struct nand_bbt_descr
*td
)
154 if (!(td
->options
& NAND_BBT_NO_OOB
))
158 if (td
->options
& NAND_BBT_VERSION
)
164 * read_bbt - [GENERIC] Read the bad block table starting from page
165 * @mtd: MTD device structure
166 * @buf: temporary buffer
167 * @page: the starting page
168 * @num: the number of bbt descriptors to read
169 * @td: the bbt describtion table
170 * @offs: block number offset in the table
172 * Read the bad block table starting from page.
174 static int read_bbt(struct mtd_info
*mtd
, uint8_t *buf
, int page
, int num
,
175 struct nand_bbt_descr
*td
, int offs
)
177 int res
, ret
= 0, i
, j
, act
= 0;
178 struct nand_chip
*this = mtd
->priv
;
179 size_t retlen
, len
, totlen
;
181 int bits
= td
->options
& NAND_BBT_NRBITS_MSK
;
182 uint8_t msk
= (uint8_t)((1 << bits
) - 1);
184 int reserved_block_code
= td
->reserved_block_code
;
186 totlen
= (num
* bits
) >> 3;
187 marker_len
= add_marker_len(td
);
188 from
= ((loff_t
)page
) << this->page_shift
;
191 len
= min(totlen
, (size_t)(1 << this->bbt_erase_shift
));
194 * In case the BBT marker is not in the OOB area it
195 * will be just in the first page.
201 res
= mtd_read(mtd
, from
, len
, &retlen
, buf
);
203 if (mtd_is_eccerr(res
)) {
204 pr_info("nand_bbt: ECC error in BBT at "
205 "0x%012llx\n", from
& ~mtd
->writesize
);
207 } else if (mtd_is_bitflip(res
)) {
208 pr_info("nand_bbt: corrected error in BBT at "
209 "0x%012llx\n", from
& ~mtd
->writesize
);
212 pr_info("nand_bbt: error reading BBT\n");
218 for (i
= 0; i
< len
; i
++) {
219 uint8_t dat
= buf
[i
];
220 for (j
= 0; j
< 8; j
+= bits
, act
++) {
221 uint8_t tmp
= (dat
>> j
) & msk
;
224 if (reserved_block_code
&& (tmp
== reserved_block_code
)) {
225 pr_info("nand_read_bbt: reserved block at 0x%012llx\n",
226 (loff_t
)(offs
+ act
) <<
227 this->bbt_erase_shift
);
228 bbt_mark_entry(this, offs
+ act
,
230 mtd
->ecc_stats
.bbtblocks
++;
234 * Leave it for now, if it's matured we can
235 * move this message to pr_debug.
237 pr_info("nand_read_bbt: bad block at 0x%012llx\n",
238 (loff_t
)(offs
+ act
) <<
239 this->bbt_erase_shift
);
240 /* Factory marked bad or worn out? */
242 bbt_mark_entry(this, offs
+ act
,
243 BBT_BLOCK_FACTORY_BAD
);
245 bbt_mark_entry(this, offs
+ act
,
247 mtd
->ecc_stats
.badblocks
++;
257 * read_abs_bbt - [GENERIC] Read the bad block table starting at a given page
258 * @mtd: MTD device structure
259 * @buf: temporary buffer
260 * @td: descriptor for the bad block table
261 * @chip: read the table for a specific chip, -1 read all chips; applies only if
262 * NAND_BBT_PERCHIP option is set
264 * Read the bad block table for all chips starting at a given page. We assume
265 * that the bbt bits are in consecutive order.
267 static int read_abs_bbt(struct mtd_info
*mtd
, uint8_t *buf
, struct nand_bbt_descr
*td
, int chip
)
269 struct nand_chip
*this = mtd
->priv
;
272 if (td
->options
& NAND_BBT_PERCHIP
) {
274 for (i
= 0; i
< this->numchips
; i
++) {
275 if (chip
== -1 || chip
== i
)
276 res
= read_bbt(mtd
, buf
, td
->pages
[i
],
277 this->chipsize
>> this->bbt_erase_shift
,
281 offs
+= this->chipsize
>> this->bbt_erase_shift
;
284 res
= read_bbt(mtd
, buf
, td
->pages
[0],
285 mtd
->size
>> this->bbt_erase_shift
, td
, 0);
292 /* BBT marker is in the first page, no OOB */
293 static int scan_read_data(struct mtd_info
*mtd
, uint8_t *buf
, loff_t offs
,
294 struct nand_bbt_descr
*td
)
300 if (td
->options
& NAND_BBT_VERSION
)
303 return mtd_read(mtd
, offs
, len
, &retlen
, buf
);
307 * scan_read_oob - [GENERIC] Scan data+OOB region to buffer
308 * @mtd: MTD device structure
309 * @buf: temporary buffer
310 * @offs: offset at which to scan
311 * @len: length of data region to read
313 * Scan read data from data+OOB. May traverse multiple pages, interleaving
314 * page,OOB,page,OOB,... in buf. Completes transfer and returns the "strongest"
315 * ECC condition (error or bitflip). May quit on the first (non-ECC) error.
317 static int scan_read_oob(struct mtd_info
*mtd
, uint8_t *buf
, loff_t offs
,
320 struct mtd_oob_ops ops
;
323 ops
.mode
= MTD_OPS_PLACE_OOB
;
325 ops
.ooblen
= mtd
->oobsize
;
329 ops
.len
= min(len
, (size_t)mtd
->writesize
);
330 ops
.oobbuf
= buf
+ ops
.len
;
332 res
= mtd_read_oob(mtd
, offs
, &ops
);
334 if (!mtd_is_bitflip_or_eccerr(res
))
336 else if (mtd_is_eccerr(res
) || !ret
)
340 buf
+= mtd
->oobsize
+ mtd
->writesize
;
341 len
-= mtd
->writesize
;
342 offs
+= mtd
->writesize
;
347 static int scan_read(struct mtd_info
*mtd
, uint8_t *buf
, loff_t offs
,
348 size_t len
, struct nand_bbt_descr
*td
)
350 if (td
->options
& NAND_BBT_NO_OOB
)
351 return scan_read_data(mtd
, buf
, offs
, td
);
353 return scan_read_oob(mtd
, buf
, offs
, len
);
356 /* Scan write data with oob to flash */
357 static int scan_write_bbt(struct mtd_info
*mtd
, loff_t offs
, size_t len
,
358 uint8_t *buf
, uint8_t *oob
)
360 struct mtd_oob_ops ops
;
362 ops
.mode
= MTD_OPS_PLACE_OOB
;
364 ops
.ooblen
= mtd
->oobsize
;
369 return mtd_write_oob(mtd
, offs
, &ops
);
372 static u32
bbt_get_ver_offs(struct mtd_info
*mtd
, struct nand_bbt_descr
*td
)
374 u32 ver_offs
= td
->veroffs
;
376 if (!(td
->options
& NAND_BBT_NO_OOB
))
377 ver_offs
+= mtd
->writesize
;
382 * read_abs_bbts - [GENERIC] Read the bad block table(s) for all chips starting at a given page
383 * @mtd: MTD device structure
384 * @buf: temporary buffer
385 * @td: descriptor for the bad block table
386 * @md: descriptor for the bad block table mirror
388 * Read the bad block table(s) for all chips starting at a given page. We
389 * assume that the bbt bits are in consecutive order.
391 static void read_abs_bbts(struct mtd_info
*mtd
, uint8_t *buf
,
392 struct nand_bbt_descr
*td
, struct nand_bbt_descr
*md
)
394 struct nand_chip
*this = mtd
->priv
;
396 /* Read the primary version, if available */
397 if (td
->options
& NAND_BBT_VERSION
) {
398 scan_read(mtd
, buf
, (loff_t
)td
->pages
[0] << this->page_shift
,
400 td
->version
[0] = buf
[bbt_get_ver_offs(mtd
, td
)];
401 pr_info("Bad block table at page %d, version 0x%02X\n",
402 td
->pages
[0], td
->version
[0]);
405 /* Read the mirror version, if available */
406 if (md
&& (md
->options
& NAND_BBT_VERSION
)) {
407 scan_read(mtd
, buf
, (loff_t
)md
->pages
[0] << this->page_shift
,
409 md
->version
[0] = buf
[bbt_get_ver_offs(mtd
, md
)];
410 pr_info("Bad block table at page %d, version 0x%02X\n",
411 md
->pages
[0], md
->version
[0]);
415 /* Scan a given block full */
416 static int scan_block_full(struct mtd_info
*mtd
, struct nand_bbt_descr
*bd
,
417 loff_t offs
, uint8_t *buf
, size_t readlen
,
418 int scanlen
, int numpages
)
422 ret
= scan_read_oob(mtd
, buf
, offs
, readlen
);
423 /* Ignore ECC errors when checking for BBM */
424 if (ret
&& !mtd_is_bitflip_or_eccerr(ret
))
427 for (j
= 0; j
< numpages
; j
++, buf
+= scanlen
) {
428 if (check_pattern(buf
, scanlen
, mtd
->writesize
, bd
))
434 /* Scan a given block partially */
435 static int scan_block_fast(struct mtd_info
*mtd
, struct nand_bbt_descr
*bd
,
436 loff_t offs
, uint8_t *buf
, int numpages
)
438 struct mtd_oob_ops ops
;
441 ops
.ooblen
= mtd
->oobsize
;
445 ops
.mode
= MTD_OPS_PLACE_OOB
;
447 for (j
= 0; j
< numpages
; j
++) {
449 * Read the full oob until read_oob is fixed to handle single
450 * byte reads for 16 bit buswidth.
452 ret
= mtd_read_oob(mtd
, offs
, &ops
);
453 /* Ignore ECC errors when checking for BBM */
454 if (ret
&& !mtd_is_bitflip_or_eccerr(ret
))
457 if (check_short_pattern(buf
, bd
))
460 offs
+= mtd
->writesize
;
466 * create_bbt - [GENERIC] Create a bad block table by scanning the device
467 * @mtd: MTD device structure
468 * @buf: temporary buffer
469 * @bd: descriptor for the good/bad block search pattern
470 * @chip: create the table for a specific chip, -1 read all chips; applies only
471 * if NAND_BBT_PERCHIP option is set
473 * Create a bad block table by scanning the device for the given good/bad block
476 static int create_bbt(struct mtd_info
*mtd
, uint8_t *buf
,
477 struct nand_bbt_descr
*bd
, int chip
)
479 struct nand_chip
*this = mtd
->priv
;
480 int i
, numblocks
, numpages
, scanlen
;
485 pr_info("Scanning device for bad blocks\n");
487 if (bd
->options
& NAND_BBT_SCANALLPAGES
)
488 numpages
= 1 << (this->bbt_erase_shift
- this->page_shift
);
489 else if (bd
->options
& NAND_BBT_SCAN2NDPAGE
)
494 /* We need only read few bytes from the OOB area */
499 numblocks
= mtd
->size
>> this->bbt_erase_shift
;
503 if (chip
>= this->numchips
) {
504 pr_warn("create_bbt(): chipnr (%d) > available chips (%d)\n",
505 chip
+ 1, this->numchips
);
508 numblocks
= this->chipsize
>> this->bbt_erase_shift
;
509 startblock
= chip
* numblocks
;
510 numblocks
+= startblock
;
511 from
= (loff_t
)startblock
<< this->bbt_erase_shift
;
514 if (this->bbt_options
& NAND_BBT_SCANLASTPAGE
)
515 from
+= mtd
->erasesize
- (mtd
->writesize
* numpages
);
517 for (i
= startblock
; i
< numblocks
; i
++) {
520 BUG_ON(bd
->options
& NAND_BBT_NO_OOB
);
522 if (bd
->options
& NAND_BBT_SCANALLPAGES
)
523 ret
= scan_block_full(mtd
, bd
, from
, buf
, readlen
,
526 ret
= scan_block_fast(mtd
, bd
, from
, buf
, numpages
);
532 bbt_mark_entry(this, i
, BBT_BLOCK_FACTORY_BAD
);
533 pr_warn("Bad eraseblock %d at 0x%012llx\n",
534 i
, (unsigned long long)from
);
535 mtd
->ecc_stats
.badblocks
++;
538 from
+= (1 << this->bbt_erase_shift
);
544 * search_bbt - [GENERIC] scan the device for a specific bad block table
545 * @mtd: MTD device structure
546 * @buf: temporary buffer
547 * @td: descriptor for the bad block table
549 * Read the bad block table by searching for a given ident pattern. Search is
550 * preformed either from the beginning up or from the end of the device
551 * downwards. The search starts always at the start of a block. If the option
552 * NAND_BBT_PERCHIP is given, each chip is searched for a bbt, which contains
553 * the bad block information of this chip. This is necessary to provide support
554 * for certain DOC devices.
556 * The bbt ident pattern resides in the oob area of the first page in a block.
558 static int search_bbt(struct mtd_info
*mtd
, uint8_t *buf
, struct nand_bbt_descr
*td
)
560 struct nand_chip
*this = mtd
->priv
;
562 int bits
, startblock
, block
, dir
;
563 int scanlen
= mtd
->writesize
+ mtd
->oobsize
;
565 int blocktopage
= this->bbt_erase_shift
- this->page_shift
;
567 /* Search direction top -> down? */
568 if (td
->options
& NAND_BBT_LASTBLOCK
) {
569 startblock
= (mtd
->size
>> this->bbt_erase_shift
) - 1;
576 /* Do we have a bbt per chip? */
577 if (td
->options
& NAND_BBT_PERCHIP
) {
578 chips
= this->numchips
;
579 bbtblocks
= this->chipsize
>> this->bbt_erase_shift
;
580 startblock
&= bbtblocks
- 1;
583 bbtblocks
= mtd
->size
>> this->bbt_erase_shift
;
586 /* Number of bits for each erase block in the bbt */
587 bits
= td
->options
& NAND_BBT_NRBITS_MSK
;
589 for (i
= 0; i
< chips
; i
++) {
590 /* Reset version information */
593 /* Scan the maximum number of blocks */
594 for (block
= 0; block
< td
->maxblocks
; block
++) {
596 int actblock
= startblock
+ dir
* block
;
597 loff_t offs
= (loff_t
)actblock
<< this->bbt_erase_shift
;
599 /* Read first page */
600 scan_read(mtd
, buf
, offs
, mtd
->writesize
, td
);
601 if (!check_pattern(buf
, scanlen
, mtd
->writesize
, td
)) {
602 td
->pages
[i
] = actblock
<< blocktopage
;
603 if (td
->options
& NAND_BBT_VERSION
) {
604 offs
= bbt_get_ver_offs(mtd
, td
);
605 td
->version
[i
] = buf
[offs
];
610 startblock
+= this->chipsize
>> this->bbt_erase_shift
;
612 /* Check, if we found a bbt for each requested chip */
613 for (i
= 0; i
< chips
; i
++) {
614 if (td
->pages
[i
] == -1)
615 pr_warn("Bad block table not found for chip %d\n", i
);
617 pr_info("Bad block table found at page %d, version "
618 "0x%02X\n", td
->pages
[i
], td
->version
[i
]);
624 * search_read_bbts - [GENERIC] scan the device for bad block table(s)
625 * @mtd: MTD device structure
626 * @buf: temporary buffer
627 * @td: descriptor for the bad block table
628 * @md: descriptor for the bad block table mirror
630 * Search and read the bad block table(s).
632 static void search_read_bbts(struct mtd_info
*mtd
, uint8_t *buf
,
633 struct nand_bbt_descr
*td
,
634 struct nand_bbt_descr
*md
)
636 /* Search the primary table */
637 search_bbt(mtd
, buf
, td
);
639 /* Search the mirror table */
641 search_bbt(mtd
, buf
, md
);
645 * write_bbt - [GENERIC] (Re)write the bad block table
646 * @mtd: MTD device structure
647 * @buf: temporary buffer
648 * @td: descriptor for the bad block table
649 * @md: descriptor for the bad block table mirror
650 * @chipsel: selector for a specific chip, -1 for all
652 * (Re)write the bad block table.
654 static int write_bbt(struct mtd_info
*mtd
, uint8_t *buf
,
655 struct nand_bbt_descr
*td
, struct nand_bbt_descr
*md
,
658 struct nand_chip
*this = mtd
->priv
;
659 struct erase_info einfo
;
660 int i
, res
, chip
= 0;
661 int bits
, startblock
, dir
, page
, offs
, numblocks
, sft
, sftmsk
;
662 int nrchips
, pageoffs
, ooboffs
;
664 uint8_t rcode
= td
->reserved_block_code
;
665 size_t retlen
, len
= 0;
667 struct mtd_oob_ops ops
;
669 ops
.ooblen
= mtd
->oobsize
;
672 ops
.mode
= MTD_OPS_PLACE_OOB
;
676 /* Write bad block table per chip rather than per device? */
677 if (td
->options
& NAND_BBT_PERCHIP
) {
678 numblocks
= (int)(this->chipsize
>> this->bbt_erase_shift
);
679 /* Full device write or specific chip? */
681 nrchips
= this->numchips
;
683 nrchips
= chipsel
+ 1;
687 numblocks
= (int)(mtd
->size
>> this->bbt_erase_shift
);
691 /* Loop through the chips */
692 for (; chip
< nrchips
; chip
++) {
694 * There was already a version of the table, reuse the page
695 * This applies for absolute placement too, as we have the
696 * page nr. in td->pages.
698 if (td
->pages
[chip
] != -1) {
699 page
= td
->pages
[chip
];
704 * Automatic placement of the bad block table. Search direction
707 if (td
->options
& NAND_BBT_LASTBLOCK
) {
708 startblock
= numblocks
* (chip
+ 1) - 1;
711 startblock
= chip
* numblocks
;
715 for (i
= 0; i
< td
->maxblocks
; i
++) {
716 int block
= startblock
+ dir
* i
;
717 /* Check, if the block is bad */
718 switch (bbt_get_entry(this, block
)) {
720 case BBT_BLOCK_FACTORY_BAD
:
724 (this->bbt_erase_shift
- this->page_shift
);
725 /* Check, if the block is used by the mirror table */
726 if (!md
|| md
->pages
[chip
] != page
)
729 pr_err("No space left to write bad block table\n");
733 /* Set up shift count and masks for the flash table */
734 bits
= td
->options
& NAND_BBT_NRBITS_MSK
;
737 case 1: sft
= 3; sftmsk
= 0x07; msk
[0] = 0x00; msk
[1] = 0x01;
740 case 2: sft
= 2; sftmsk
= 0x06; msk
[0] = 0x00; msk
[1] = 0x01;
743 case 4: sft
= 1; sftmsk
= 0x04; msk
[0] = 0x00; msk
[1] = 0x0C;
746 case 8: sft
= 0; sftmsk
= 0x00; msk
[0] = 0x00; msk
[1] = 0x0F;
749 default: return -EINVAL
;
752 to
= ((loff_t
)page
) << this->page_shift
;
754 /* Must we save the block contents? */
755 if (td
->options
& NAND_BBT_SAVECONTENT
) {
756 /* Make it block aligned */
757 to
&= ~((loff_t
)((1 << this->bbt_erase_shift
) - 1));
758 len
= 1 << this->bbt_erase_shift
;
759 res
= mtd_read(mtd
, to
, len
, &retlen
, buf
);
762 pr_info("nand_bbt: error reading block "
763 "for writing the bad block table\n");
766 pr_warn("nand_bbt: ECC error while reading "
767 "block for writing bad block table\n");
770 ops
.ooblen
= (len
>> this->page_shift
) * mtd
->oobsize
;
771 ops
.oobbuf
= &buf
[len
];
772 res
= mtd_read_oob(mtd
, to
+ mtd
->writesize
, &ops
);
773 if (res
< 0 || ops
.oobretlen
!= ops
.ooblen
)
776 /* Calc the byte offset in the buffer */
777 pageoffs
= page
- (int)(to
>> this->page_shift
);
778 offs
= pageoffs
<< this->page_shift
;
779 /* Preset the bbt area with 0xff */
780 memset(&buf
[offs
], 0xff, (size_t)(numblocks
>> sft
));
781 ooboffs
= len
+ (pageoffs
* mtd
->oobsize
);
783 } else if (td
->options
& NAND_BBT_NO_OOB
) {
786 /* The version byte */
787 if (td
->options
& NAND_BBT_VERSION
)
790 len
= (size_t)(numblocks
>> sft
);
792 /* Make it page aligned! */
793 len
= ALIGN(len
, mtd
->writesize
);
794 /* Preset the buffer with 0xff */
795 memset(buf
, 0xff, len
);
796 /* Pattern is located at the begin of first page */
797 memcpy(buf
, td
->pattern
, td
->len
);
800 len
= (size_t)(numblocks
>> sft
);
801 /* Make it page aligned! */
802 len
= ALIGN(len
, mtd
->writesize
);
803 /* Preset the buffer with 0xff */
804 memset(buf
, 0xff, len
+
805 (len
>> this->page_shift
)* mtd
->oobsize
);
808 /* Pattern is located in oob area of first page */
809 memcpy(&buf
[ooboffs
+ td
->offs
], td
->pattern
, td
->len
);
812 if (td
->options
& NAND_BBT_VERSION
)
813 buf
[ooboffs
+ td
->veroffs
] = td
->version
[chip
];
815 /* Walk through the memory table */
816 for (i
= 0; i
< numblocks
; i
++) {
818 int sftcnt
= (i
<< (3 - sft
)) & sftmsk
;
819 dat
= bbt_get_entry(this, chip
* numblocks
+ i
);
820 /* Do not store the reserved bbt blocks! */
821 buf
[offs
+ (i
>> sft
)] &= ~(msk
[dat
] << sftcnt
);
824 memset(&einfo
, 0, sizeof(einfo
));
827 einfo
.len
= 1 << this->bbt_erase_shift
;
828 res
= nand_erase_nand(mtd
, &einfo
, 1);
832 res
= scan_write_bbt(mtd
, to
, len
, buf
,
833 td
->options
& NAND_BBT_NO_OOB
? NULL
:
838 pr_info("Bad block table written to 0x%012llx, version 0x%02X\n",
839 (unsigned long long)to
, td
->version
[chip
]);
841 /* Mark it as used */
842 td
->pages
[chip
] = page
;
847 pr_warn("nand_bbt: error while writing bad block table %d\n", res
);
852 * nand_memory_bbt - [GENERIC] create a memory based bad block table
853 * @mtd: MTD device structure
854 * @bd: descriptor for the good/bad block search pattern
856 * The function creates a memory based bbt by scanning the device for
857 * manufacturer / software marked good / bad blocks.
859 static inline int nand_memory_bbt(struct mtd_info
*mtd
, struct nand_bbt_descr
*bd
)
861 struct nand_chip
*this = mtd
->priv
;
863 return create_bbt(mtd
, this->buffers
->databuf
, bd
, -1);
867 * check_create - [GENERIC] create and write bbt(s) if necessary
868 * @mtd: MTD device structure
869 * @buf: temporary buffer
870 * @bd: descriptor for the good/bad block search pattern
872 * The function checks the results of the previous call to read_bbt and creates
873 * / updates the bbt(s) if necessary. Creation is necessary if no bbt was found
874 * for the chip/device. Update is necessary if one of the tables is missing or
875 * the version nr. of one table is less than the other.
877 static int check_create(struct mtd_info
*mtd
, uint8_t *buf
, struct nand_bbt_descr
*bd
)
879 int i
, chips
, writeops
, create
, chipsel
, res
, res2
;
880 struct nand_chip
*this = mtd
->priv
;
881 struct nand_bbt_descr
*td
= this->bbt_td
;
882 struct nand_bbt_descr
*md
= this->bbt_md
;
883 struct nand_bbt_descr
*rd
, *rd2
;
885 /* Do we have a bbt per chip? */
886 if (td
->options
& NAND_BBT_PERCHIP
)
887 chips
= this->numchips
;
891 for (i
= 0; i
< chips
; i
++) {
897 /* Per chip or per device? */
898 chipsel
= (td
->options
& NAND_BBT_PERCHIP
) ? i
: -1;
899 /* Mirrored table available? */
901 if (td
->pages
[i
] == -1 && md
->pages
[i
] == -1) {
904 } else if (td
->pages
[i
] == -1) {
907 } else if (md
->pages
[i
] == -1) {
910 } else if (td
->version
[i
] == md
->version
[i
]) {
912 if (!(td
->options
& NAND_BBT_VERSION
))
914 } else if (((int8_t)(td
->version
[i
] - md
->version
[i
])) > 0) {
922 if (td
->pages
[i
] == -1) {
931 /* Create the bad block table by scanning the device? */
932 if (!(td
->options
& NAND_BBT_CREATE
))
935 /* Create the table in memory by scanning the chip(s) */
936 if (!(this->bbt_options
& NAND_BBT_CREATE_EMPTY
))
937 create_bbt(mtd
, buf
, bd
, chipsel
);
944 /* Read back first? */
946 res
= read_abs_bbt(mtd
, buf
, rd
, chipsel
);
947 if (mtd_is_eccerr(res
)) {
948 /* Mark table as invalid */
955 /* If they weren't versioned, read both */
957 res2
= read_abs_bbt(mtd
, buf
, rd2
, chipsel
);
958 if (mtd_is_eccerr(res2
)) {
959 /* Mark table as invalid */
967 /* Scrub the flash table(s)? */
968 if (mtd_is_bitflip(res
) || mtd_is_bitflip(res2
))
971 /* Update version numbers before writing */
973 td
->version
[i
] = max(td
->version
[i
], md
->version
[i
]);
974 md
->version
[i
] = td
->version
[i
];
977 /* Write the bad block table to the device? */
978 if ((writeops
& 0x01) && (td
->options
& NAND_BBT_WRITE
)) {
979 res
= write_bbt(mtd
, buf
, td
, md
, chipsel
);
984 /* Write the mirror bad block table to the device? */
985 if ((writeops
& 0x02) && md
&& (md
->options
& NAND_BBT_WRITE
)) {
986 res
= write_bbt(mtd
, buf
, md
, td
, chipsel
);
995 * mark_bbt_regions - [GENERIC] mark the bad block table regions
996 * @mtd: MTD device structure
997 * @td: bad block table descriptor
999 * The bad block table regions are marked as "bad" to prevent accidental
1000 * erasures / writes. The regions are identified by the mark 0x02.
1002 static void mark_bbt_region(struct mtd_info
*mtd
, struct nand_bbt_descr
*td
)
1004 struct nand_chip
*this = mtd
->priv
;
1005 int i
, j
, chips
, block
, nrblocks
, update
;
1008 /* Do we have a bbt per chip? */
1009 if (td
->options
& NAND_BBT_PERCHIP
) {
1010 chips
= this->numchips
;
1011 nrblocks
= (int)(this->chipsize
>> this->bbt_erase_shift
);
1014 nrblocks
= (int)(mtd
->size
>> this->bbt_erase_shift
);
1017 for (i
= 0; i
< chips
; i
++) {
1018 if ((td
->options
& NAND_BBT_ABSPAGE
) ||
1019 !(td
->options
& NAND_BBT_WRITE
)) {
1020 if (td
->pages
[i
] == -1)
1022 block
= td
->pages
[i
] >> (this->bbt_erase_shift
- this->page_shift
);
1023 oldval
= bbt_get_entry(this, block
);
1024 bbt_mark_entry(this, block
, BBT_BLOCK_RESERVED
);
1025 if ((oldval
!= BBT_BLOCK_RESERVED
) &&
1026 td
->reserved_block_code
)
1027 nand_update_bbt(mtd
, (loff_t
)block
<<
1028 this->bbt_erase_shift
);
1032 if (td
->options
& NAND_BBT_LASTBLOCK
)
1033 block
= ((i
+ 1) * nrblocks
) - td
->maxblocks
;
1035 block
= i
* nrblocks
;
1036 for (j
= 0; j
< td
->maxblocks
; j
++) {
1037 oldval
= bbt_get_entry(this, block
);
1038 bbt_mark_entry(this, block
, BBT_BLOCK_RESERVED
);
1039 if (oldval
!= BBT_BLOCK_RESERVED
)
1044 * If we want reserved blocks to be recorded to flash, and some
1045 * new ones have been marked, then we need to update the stored
1046 * bbts. This should only happen once.
1048 if (update
&& td
->reserved_block_code
)
1049 nand_update_bbt(mtd
, (loff_t
)(block
- 1) <<
1050 this->bbt_erase_shift
);
1055 * verify_bbt_descr - verify the bad block description
1056 * @mtd: MTD device structure
1057 * @bd: the table to verify
1059 * This functions performs a few sanity checks on the bad block description
1062 static void verify_bbt_descr(struct mtd_info
*mtd
, struct nand_bbt_descr
*bd
)
1064 struct nand_chip
*this = mtd
->priv
;
1072 pattern_len
= bd
->len
;
1073 bits
= bd
->options
& NAND_BBT_NRBITS_MSK
;
1075 BUG_ON((this->bbt_options
& NAND_BBT_NO_OOB
) &&
1076 !(this->bbt_options
& NAND_BBT_USE_FLASH
));
1079 if (bd
->options
& NAND_BBT_VERSION
)
1082 if (bd
->options
& NAND_BBT_NO_OOB
) {
1083 BUG_ON(!(this->bbt_options
& NAND_BBT_USE_FLASH
));
1084 BUG_ON(!(this->bbt_options
& NAND_BBT_NO_OOB
));
1086 if (bd
->options
& NAND_BBT_VERSION
)
1087 BUG_ON(bd
->veroffs
!= bd
->len
);
1088 BUG_ON(bd
->options
& NAND_BBT_SAVECONTENT
);
1091 if (bd
->options
& NAND_BBT_PERCHIP
)
1092 table_size
= this->chipsize
>> this->bbt_erase_shift
;
1094 table_size
= mtd
->size
>> this->bbt_erase_shift
;
1097 if (bd
->options
& NAND_BBT_NO_OOB
)
1098 table_size
+= pattern_len
;
1099 BUG_ON(table_size
> (1 << this->bbt_erase_shift
));
1103 * nand_scan_bbt - [NAND Interface] scan, find, read and maybe create bad block table(s)
1104 * @mtd: MTD device structure
1105 * @bd: descriptor for the good/bad block search pattern
1107 * The function checks, if a bad block table(s) is/are already available. If
1108 * not it scans the device for manufacturer marked good / bad blocks and writes
1109 * the bad block table(s) to the selected place.
1111 * The bad block table memory is allocated here. It must be freed by calling
1112 * the nand_free_bbt function.
1114 int nand_scan_bbt(struct mtd_info
*mtd
, struct nand_bbt_descr
*bd
)
1116 struct nand_chip
*this = mtd
->priv
;
1119 struct nand_bbt_descr
*td
= this->bbt_td
;
1120 struct nand_bbt_descr
*md
= this->bbt_md
;
1122 len
= mtd
->size
>> (this->bbt_erase_shift
+ 2);
1124 * Allocate memory (2bit per block) and clear the memory bad block
1127 this->bbt
= kzalloc(len
, GFP_KERNEL
);
1132 * If no primary table decriptor is given, scan the device to build a
1133 * memory based bad block table.
1136 if ((res
= nand_memory_bbt(mtd
, bd
))) {
1137 pr_err("nand_bbt: can't scan flash and build the RAM-based BBT\n");
1143 verify_bbt_descr(mtd
, td
);
1144 verify_bbt_descr(mtd
, md
);
1146 /* Allocate a temporary buffer for one eraseblock incl. oob */
1147 len
= (1 << this->bbt_erase_shift
);
1148 len
+= (len
>> this->page_shift
) * mtd
->oobsize
;
1156 /* Is the bbt at a given page? */
1157 if (td
->options
& NAND_BBT_ABSPAGE
) {
1158 read_abs_bbts(mtd
, buf
, td
, md
);
1160 /* Search the bad block table using a pattern in oob */
1161 search_read_bbts(mtd
, buf
, td
, md
);
1164 res
= check_create(mtd
, buf
, bd
);
1166 /* Prevent the bbt regions from erasing / writing */
1167 mark_bbt_region(mtd
, td
);
1169 mark_bbt_region(mtd
, md
);
1176 * nand_update_bbt - update bad block table(s)
1177 * @mtd: MTD device structure
1178 * @offs: the offset of the newly marked block
1180 * The function updates the bad block table(s).
1182 static int nand_update_bbt(struct mtd_info
*mtd
, loff_t offs
)
1184 struct nand_chip
*this = mtd
->priv
;
1188 struct nand_bbt_descr
*td
= this->bbt_td
;
1189 struct nand_bbt_descr
*md
= this->bbt_md
;
1191 if (!this->bbt
|| !td
)
1194 /* Allocate a temporary buffer for one eraseblock incl. oob */
1195 len
= (1 << this->bbt_erase_shift
);
1196 len
+= (len
>> this->page_shift
) * mtd
->oobsize
;
1197 buf
= kmalloc(len
, GFP_KERNEL
);
1201 /* Do we have a bbt per chip? */
1202 if (td
->options
& NAND_BBT_PERCHIP
) {
1203 chip
= (int)(offs
>> this->chip_shift
);
1210 td
->version
[chip
]++;
1212 md
->version
[chip
]++;
1214 /* Write the bad block table to the device? */
1215 if (td
->options
& NAND_BBT_WRITE
) {
1216 res
= write_bbt(mtd
, buf
, td
, md
, chipsel
);
1220 /* Write the mirror bad block table to the device? */
1221 if (md
&& (md
->options
& NAND_BBT_WRITE
)) {
1222 res
= write_bbt(mtd
, buf
, md
, td
, chipsel
);
1231 * Define some generic bad / good block scan pattern which are used
1232 * while scanning a device for factory marked good / bad blocks.
1234 static uint8_t scan_ff_pattern
[] = { 0xff, 0xff };
1236 /* Generic flash bbt descriptors */
1237 static uint8_t bbt_pattern
[] = {'B', 'b', 't', '0' };
1238 static uint8_t mirror_pattern
[] = {'1', 't', 'b', 'B' };
1240 static struct nand_bbt_descr bbt_main_descr
= {
1241 .options
= NAND_BBT_LASTBLOCK
| NAND_BBT_CREATE
| NAND_BBT_WRITE
1242 | NAND_BBT_2BIT
| NAND_BBT_VERSION
| NAND_BBT_PERCHIP
,
1246 .maxblocks
= NAND_BBT_SCAN_MAXBLOCKS
,
1247 .pattern
= bbt_pattern
1250 static struct nand_bbt_descr bbt_mirror_descr
= {
1251 .options
= NAND_BBT_LASTBLOCK
| NAND_BBT_CREATE
| NAND_BBT_WRITE
1252 | NAND_BBT_2BIT
| NAND_BBT_VERSION
| NAND_BBT_PERCHIP
,
1256 .maxblocks
= NAND_BBT_SCAN_MAXBLOCKS
,
1257 .pattern
= mirror_pattern
1260 static struct nand_bbt_descr bbt_main_no_oob_descr
= {
1261 .options
= NAND_BBT_LASTBLOCK
| NAND_BBT_CREATE
| NAND_BBT_WRITE
1262 | NAND_BBT_2BIT
| NAND_BBT_VERSION
| NAND_BBT_PERCHIP
1266 .maxblocks
= NAND_BBT_SCAN_MAXBLOCKS
,
1267 .pattern
= bbt_pattern
1270 static struct nand_bbt_descr bbt_mirror_no_oob_descr
= {
1271 .options
= NAND_BBT_LASTBLOCK
| NAND_BBT_CREATE
| NAND_BBT_WRITE
1272 | NAND_BBT_2BIT
| NAND_BBT_VERSION
| NAND_BBT_PERCHIP
1276 .maxblocks
= NAND_BBT_SCAN_MAXBLOCKS
,
1277 .pattern
= mirror_pattern
1280 #define BADBLOCK_SCAN_MASK (~NAND_BBT_NO_OOB)
1282 * nand_create_badblock_pattern - [INTERN] Creates a BBT descriptor structure
1283 * @this: NAND chip to create descriptor for
1285 * This function allocates and initializes a nand_bbt_descr for BBM detection
1286 * based on the properties of @this. The new descriptor is stored in
1287 * this->badblock_pattern. Thus, this->badblock_pattern should be NULL when
1288 * passed to this function.
1290 static int nand_create_badblock_pattern(struct nand_chip
*this)
1292 struct nand_bbt_descr
*bd
;
1293 if (this->badblock_pattern
) {
1294 pr_warn("Bad block pattern already allocated; not replacing\n");
1297 bd
= kzalloc(sizeof(*bd
), GFP_KERNEL
);
1300 bd
->options
= this->bbt_options
& BADBLOCK_SCAN_MASK
;
1301 bd
->offs
= this->badblockpos
;
1302 bd
->len
= (this->options
& NAND_BUSWIDTH_16
) ? 2 : 1;
1303 bd
->pattern
= scan_ff_pattern
;
1304 bd
->options
|= NAND_BBT_DYNAMICSTRUCT
;
1305 this->badblock_pattern
= bd
;
1310 * nand_default_bbt - [NAND Interface] Select a default bad block table for the device
1311 * @mtd: MTD device structure
1313 * This function selects the default bad block table support for the device and
1314 * calls the nand_scan_bbt function.
1316 int nand_default_bbt(struct mtd_info
*mtd
)
1318 struct nand_chip
*this = mtd
->priv
;
1320 /* Is a flash based bad block table requested? */
1321 if (this->bbt_options
& NAND_BBT_USE_FLASH
) {
1322 /* Use the default pattern descriptors */
1323 if (!this->bbt_td
) {
1324 if (this->bbt_options
& NAND_BBT_NO_OOB
) {
1325 this->bbt_td
= &bbt_main_no_oob_descr
;
1326 this->bbt_md
= &bbt_mirror_no_oob_descr
;
1328 this->bbt_td
= &bbt_main_descr
;
1329 this->bbt_md
= &bbt_mirror_descr
;
1333 this->bbt_td
= NULL
;
1334 this->bbt_md
= NULL
;
1337 if (!this->badblock_pattern
)
1338 nand_create_badblock_pattern(this);
1340 return nand_scan_bbt(mtd
, this->badblock_pattern
);
1344 * nand_isbad_bbt - [NAND Interface] Check if a block is bad
1345 * @mtd: MTD device structure
1346 * @offs: offset in the device
1347 * @allowbbt: allow access to bad block table region
1349 int nand_isbad_bbt(struct mtd_info
*mtd
, loff_t offs
, int allowbbt
)
1351 struct nand_chip
*this = mtd
->priv
;
1354 block
= (int)(offs
>> this->bbt_erase_shift
);
1355 res
= bbt_get_entry(this, block
);
1357 pr_debug("nand_isbad_bbt(): bbt info for offs 0x%08x: "
1358 "(block %d) 0x%02x\n",
1359 (unsigned int)offs
, block
, res
);
1362 case BBT_BLOCK_GOOD
:
1364 case BBT_BLOCK_WORN
:
1366 case BBT_BLOCK_RESERVED
:
1367 return allowbbt
? 0 : 1;
1373 * nand_markbad_bbt - [NAND Interface] Mark a block bad in the BBT
1374 * @mtd: MTD device structure
1375 * @offs: offset of the bad block
1377 int nand_markbad_bbt(struct mtd_info
*mtd
, loff_t offs
)
1379 struct nand_chip
*this = mtd
->priv
;
1382 block
= (int)(offs
>> this->bbt_erase_shift
);
1384 /* Mark bad block in memory */
1385 bbt_mark_entry(this, block
, BBT_BLOCK_WORN
);
1387 /* Update flash-based bad block table */
1388 if (this->bbt_options
& NAND_BBT_USE_FLASH
)
1389 ret
= nand_update_bbt(mtd
, offs
);
1394 EXPORT_SYMBOL(nand_scan_bbt
);
1395 EXPORT_SYMBOL(nand_default_bbt
);