isci: fix oem parameter validation on single controller skus
[linux/fpc-iii.git] / drivers / gpio / gpio-max732x.c
blob9504120812a50c1f819c4ed63340cef98e694c53
1 /*
2 * MAX732x I2C Port Expander with 8/16 I/O
4 * Copyright (C) 2007 Marvell International Ltd.
5 * Copyright (C) 2008 Jack Ren <jack.ren@marvell.com>
6 * Copyright (C) 2008 Eric Miao <eric.miao@marvell.com>
8 * Derived from drivers/gpio/pca953x.c
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License as published by
12 * the Free Software Foundation; version 2 of the License.
15 #include <linux/module.h>
16 #include <linux/init.h>
17 #include <linux/slab.h>
18 #include <linux/string.h>
19 #include <linux/gpio.h>
20 #include <linux/interrupt.h>
21 #include <linux/irq.h>
22 #include <linux/i2c.h>
23 #include <linux/i2c/max732x.h>
27 * Each port of MAX732x (including MAX7319) falls into one of the
28 * following three types:
30 * - Push Pull Output
31 * - Input
32 * - Open Drain I/O
34 * designated by 'O', 'I' and 'P' individually according to MAXIM's
35 * datasheets. 'I' and 'P' ports are interrupt capables, some with
36 * a dedicated interrupt mask.
38 * There are two groups of I/O ports, each group usually includes
39 * up to 8 I/O ports, and is accessed by a specific I2C address:
41 * - Group A : by I2C address 0b'110xxxx
42 * - Group B : by I2C address 0b'101xxxx
44 * where 'xxxx' is decided by the connections of pin AD2/AD0. The
45 * address used also affects the initial state of output signals.
47 * Within each group of ports, there are five known combinations of
48 * I/O ports: 4I4O, 4P4O, 8I, 8P, 8O, see the definitions below for
49 * the detailed organization of these ports. Only Goup A is interrupt
50 * capable.
52 * GPIO numbers start from 'gpio_base + 0' to 'gpio_base + 8/16',
53 * and GPIOs from GROUP_A are numbered before those from GROUP_B
54 * (if there are two groups).
56 * NOTE: MAX7328/MAX7329 are drop-in replacements for PCF8574/a, so
57 * they are not supported by this driver.
60 #define PORT_NONE 0x0 /* '/' No Port */
61 #define PORT_OUTPUT 0x1 /* 'O' Push-Pull, Output Only */
62 #define PORT_INPUT 0x2 /* 'I' Input Only */
63 #define PORT_OPENDRAIN 0x3 /* 'P' Open-Drain, I/O */
65 #define IO_4I4O 0x5AA5 /* O7 O6 I5 I4 I3 I2 O1 O0 */
66 #define IO_4P4O 0x5FF5 /* O7 O6 P5 P4 P3 P2 O1 O0 */
67 #define IO_8I 0xAAAA /* I7 I6 I5 I4 I3 I2 I1 I0 */
68 #define IO_8P 0xFFFF /* P7 P6 P5 P4 P3 P2 P1 P0 */
69 #define IO_8O 0x5555 /* O7 O6 O5 O4 O3 O2 O1 O0 */
71 #define GROUP_A(x) ((x) & 0xffff) /* I2C Addr: 0b'110xxxx */
72 #define GROUP_B(x) ((x) << 16) /* I2C Addr: 0b'101xxxx */
74 #define INT_NONE 0x0 /* No interrupt capability */
75 #define INT_NO_MASK 0x1 /* Has interrupts, no mask */
76 #define INT_INDEP_MASK 0x2 /* Has interrupts, independent mask */
77 #define INT_MERGED_MASK 0x3 /* Has interrupts, merged mask */
79 #define INT_CAPS(x) (((uint64_t)(x)) << 32)
81 enum {
82 MAX7319,
83 MAX7320,
84 MAX7321,
85 MAX7322,
86 MAX7323,
87 MAX7324,
88 MAX7325,
89 MAX7326,
90 MAX7327,
93 static uint64_t max732x_features[] = {
94 [MAX7319] = GROUP_A(IO_8I) | INT_CAPS(INT_MERGED_MASK),
95 [MAX7320] = GROUP_B(IO_8O),
96 [MAX7321] = GROUP_A(IO_8P) | INT_CAPS(INT_NO_MASK),
97 [MAX7322] = GROUP_A(IO_4I4O) | INT_CAPS(INT_MERGED_MASK),
98 [MAX7323] = GROUP_A(IO_4P4O) | INT_CAPS(INT_INDEP_MASK),
99 [MAX7324] = GROUP_A(IO_8I) | GROUP_B(IO_8O) | INT_CAPS(INT_MERGED_MASK),
100 [MAX7325] = GROUP_A(IO_8P) | GROUP_B(IO_8O) | INT_CAPS(INT_NO_MASK),
101 [MAX7326] = GROUP_A(IO_4I4O) | GROUP_B(IO_8O) | INT_CAPS(INT_MERGED_MASK),
102 [MAX7327] = GROUP_A(IO_4P4O) | GROUP_B(IO_8O) | INT_CAPS(INT_NO_MASK),
105 static const struct i2c_device_id max732x_id[] = {
106 { "max7319", MAX7319 },
107 { "max7320", MAX7320 },
108 { "max7321", MAX7321 },
109 { "max7322", MAX7322 },
110 { "max7323", MAX7323 },
111 { "max7324", MAX7324 },
112 { "max7325", MAX7325 },
113 { "max7326", MAX7326 },
114 { "max7327", MAX7327 },
115 { },
117 MODULE_DEVICE_TABLE(i2c, max732x_id);
119 struct max732x_chip {
120 struct gpio_chip gpio_chip;
122 struct i2c_client *client; /* "main" client */
123 struct i2c_client *client_dummy;
124 struct i2c_client *client_group_a;
125 struct i2c_client *client_group_b;
127 unsigned int mask_group_a;
128 unsigned int dir_input;
129 unsigned int dir_output;
131 struct mutex lock;
132 uint8_t reg_out[2];
134 #ifdef CONFIG_GPIO_MAX732X_IRQ
135 struct mutex irq_lock;
136 int irq_base;
137 uint8_t irq_mask;
138 uint8_t irq_mask_cur;
139 uint8_t irq_trig_raise;
140 uint8_t irq_trig_fall;
141 uint8_t irq_features;
142 #endif
145 static int max732x_writeb(struct max732x_chip *chip, int group_a, uint8_t val)
147 struct i2c_client *client;
148 int ret;
150 client = group_a ? chip->client_group_a : chip->client_group_b;
151 ret = i2c_smbus_write_byte(client, val);
152 if (ret < 0) {
153 dev_err(&client->dev, "failed writing\n");
154 return ret;
157 return 0;
160 static int max732x_readb(struct max732x_chip *chip, int group_a, uint8_t *val)
162 struct i2c_client *client;
163 int ret;
165 client = group_a ? chip->client_group_a : chip->client_group_b;
166 ret = i2c_smbus_read_byte(client);
167 if (ret < 0) {
168 dev_err(&client->dev, "failed reading\n");
169 return ret;
172 *val = (uint8_t)ret;
173 return 0;
176 static inline int is_group_a(struct max732x_chip *chip, unsigned off)
178 return (1u << off) & chip->mask_group_a;
181 static int max732x_gpio_get_value(struct gpio_chip *gc, unsigned off)
183 struct max732x_chip *chip;
184 uint8_t reg_val;
185 int ret;
187 chip = container_of(gc, struct max732x_chip, gpio_chip);
189 ret = max732x_readb(chip, is_group_a(chip, off), &reg_val);
190 if (ret < 0)
191 return 0;
193 return reg_val & (1u << (off & 0x7));
196 static void max732x_gpio_set_value(struct gpio_chip *gc, unsigned off, int val)
198 struct max732x_chip *chip;
199 uint8_t reg_out, mask = 1u << (off & 0x7);
200 int ret;
202 chip = container_of(gc, struct max732x_chip, gpio_chip);
204 mutex_lock(&chip->lock);
206 reg_out = (off > 7) ? chip->reg_out[1] : chip->reg_out[0];
207 reg_out = (val) ? reg_out | mask : reg_out & ~mask;
209 ret = max732x_writeb(chip, is_group_a(chip, off), reg_out);
210 if (ret < 0)
211 goto out;
213 /* update the shadow register then */
214 if (off > 7)
215 chip->reg_out[1] = reg_out;
216 else
217 chip->reg_out[0] = reg_out;
218 out:
219 mutex_unlock(&chip->lock);
222 static int max732x_gpio_direction_input(struct gpio_chip *gc, unsigned off)
224 struct max732x_chip *chip;
225 unsigned int mask = 1u << off;
227 chip = container_of(gc, struct max732x_chip, gpio_chip);
229 if ((mask & chip->dir_input) == 0) {
230 dev_dbg(&chip->client->dev, "%s port %d is output only\n",
231 chip->client->name, off);
232 return -EACCES;
236 * Open-drain pins must be set to high impedance (which is
237 * equivalent to output-high) to be turned into an input.
239 if ((mask & chip->dir_output))
240 max732x_gpio_set_value(gc, off, 1);
242 return 0;
245 static int max732x_gpio_direction_output(struct gpio_chip *gc,
246 unsigned off, int val)
248 struct max732x_chip *chip;
249 unsigned int mask = 1u << off;
251 chip = container_of(gc, struct max732x_chip, gpio_chip);
253 if ((mask & chip->dir_output) == 0) {
254 dev_dbg(&chip->client->dev, "%s port %d is input only\n",
255 chip->client->name, off);
256 return -EACCES;
259 max732x_gpio_set_value(gc, off, val);
260 return 0;
263 #ifdef CONFIG_GPIO_MAX732X_IRQ
264 static int max732x_writew(struct max732x_chip *chip, uint16_t val)
266 int ret;
268 val = cpu_to_le16(val);
270 ret = i2c_master_send(chip->client_group_a, (char *)&val, 2);
271 if (ret < 0) {
272 dev_err(&chip->client_group_a->dev, "failed writing\n");
273 return ret;
276 return 0;
279 static int max732x_readw(struct max732x_chip *chip, uint16_t *val)
281 int ret;
283 ret = i2c_master_recv(chip->client_group_a, (char *)val, 2);
284 if (ret < 0) {
285 dev_err(&chip->client_group_a->dev, "failed reading\n");
286 return ret;
289 *val = le16_to_cpu(*val);
290 return 0;
293 static void max732x_irq_update_mask(struct max732x_chip *chip)
295 uint16_t msg;
297 if (chip->irq_mask == chip->irq_mask_cur)
298 return;
300 chip->irq_mask = chip->irq_mask_cur;
302 if (chip->irq_features == INT_NO_MASK)
303 return;
305 mutex_lock(&chip->lock);
307 switch (chip->irq_features) {
308 case INT_INDEP_MASK:
309 msg = (chip->irq_mask << 8) | chip->reg_out[0];
310 max732x_writew(chip, msg);
311 break;
313 case INT_MERGED_MASK:
314 msg = chip->irq_mask | chip->reg_out[0];
315 max732x_writeb(chip, 1, (uint8_t)msg);
316 break;
319 mutex_unlock(&chip->lock);
322 static int max732x_gpio_to_irq(struct gpio_chip *gc, unsigned off)
324 struct max732x_chip *chip;
326 chip = container_of(gc, struct max732x_chip, gpio_chip);
327 return chip->irq_base + off;
330 static void max732x_irq_mask(struct irq_data *d)
332 struct max732x_chip *chip = irq_data_get_irq_chip_data(d);
334 chip->irq_mask_cur &= ~(1 << (d->irq - chip->irq_base));
337 static void max732x_irq_unmask(struct irq_data *d)
339 struct max732x_chip *chip = irq_data_get_irq_chip_data(d);
341 chip->irq_mask_cur |= 1 << (d->irq - chip->irq_base);
344 static void max732x_irq_bus_lock(struct irq_data *d)
346 struct max732x_chip *chip = irq_data_get_irq_chip_data(d);
348 mutex_lock(&chip->irq_lock);
349 chip->irq_mask_cur = chip->irq_mask;
352 static void max732x_irq_bus_sync_unlock(struct irq_data *d)
354 struct max732x_chip *chip = irq_data_get_irq_chip_data(d);
356 max732x_irq_update_mask(chip);
357 mutex_unlock(&chip->irq_lock);
360 static int max732x_irq_set_type(struct irq_data *d, unsigned int type)
362 struct max732x_chip *chip = irq_data_get_irq_chip_data(d);
363 uint16_t off = d->irq - chip->irq_base;
364 uint16_t mask = 1 << off;
366 if (!(mask & chip->dir_input)) {
367 dev_dbg(&chip->client->dev, "%s port %d is output only\n",
368 chip->client->name, off);
369 return -EACCES;
372 if (!(type & IRQ_TYPE_EDGE_BOTH)) {
373 dev_err(&chip->client->dev, "irq %d: unsupported type %d\n",
374 d->irq, type);
375 return -EINVAL;
378 if (type & IRQ_TYPE_EDGE_FALLING)
379 chip->irq_trig_fall |= mask;
380 else
381 chip->irq_trig_fall &= ~mask;
383 if (type & IRQ_TYPE_EDGE_RISING)
384 chip->irq_trig_raise |= mask;
385 else
386 chip->irq_trig_raise &= ~mask;
388 return max732x_gpio_direction_input(&chip->gpio_chip, off);
391 static struct irq_chip max732x_irq_chip = {
392 .name = "max732x",
393 .irq_mask = max732x_irq_mask,
394 .irq_unmask = max732x_irq_unmask,
395 .irq_bus_lock = max732x_irq_bus_lock,
396 .irq_bus_sync_unlock = max732x_irq_bus_sync_unlock,
397 .irq_set_type = max732x_irq_set_type,
400 static uint8_t max732x_irq_pending(struct max732x_chip *chip)
402 uint8_t cur_stat;
403 uint8_t old_stat;
404 uint8_t trigger;
405 uint8_t pending;
406 uint16_t status;
407 int ret;
409 ret = max732x_readw(chip, &status);
410 if (ret)
411 return 0;
413 trigger = status >> 8;
414 trigger &= chip->irq_mask;
416 if (!trigger)
417 return 0;
419 cur_stat = status & 0xFF;
420 cur_stat &= chip->irq_mask;
422 old_stat = cur_stat ^ trigger;
424 pending = (old_stat & chip->irq_trig_fall) |
425 (cur_stat & chip->irq_trig_raise);
426 pending &= trigger;
428 return pending;
431 static irqreturn_t max732x_irq_handler(int irq, void *devid)
433 struct max732x_chip *chip = devid;
434 uint8_t pending;
435 uint8_t level;
437 pending = max732x_irq_pending(chip);
439 if (!pending)
440 return IRQ_HANDLED;
442 do {
443 level = __ffs(pending);
444 handle_nested_irq(level + chip->irq_base);
446 pending &= ~(1 << level);
447 } while (pending);
449 return IRQ_HANDLED;
452 static int max732x_irq_setup(struct max732x_chip *chip,
453 const struct i2c_device_id *id)
455 struct i2c_client *client = chip->client;
456 struct max732x_platform_data *pdata = client->dev.platform_data;
457 int has_irq = max732x_features[id->driver_data] >> 32;
458 int ret;
460 if (pdata->irq_base && has_irq != INT_NONE) {
461 int lvl;
463 chip->irq_base = pdata->irq_base;
464 chip->irq_features = has_irq;
465 mutex_init(&chip->irq_lock);
467 for (lvl = 0; lvl < chip->gpio_chip.ngpio; lvl++) {
468 int irq = lvl + chip->irq_base;
470 if (!(chip->dir_input & (1 << lvl)))
471 continue;
473 irq_set_chip_data(irq, chip);
474 irq_set_chip_and_handler(irq, &max732x_irq_chip,
475 handle_edge_irq);
476 irq_set_nested_thread(irq, 1);
477 #ifdef CONFIG_ARM
478 set_irq_flags(irq, IRQF_VALID);
479 #else
480 irq_set_noprobe(irq);
481 #endif
484 ret = request_threaded_irq(client->irq,
485 NULL,
486 max732x_irq_handler,
487 IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
488 dev_name(&client->dev), chip);
489 if (ret) {
490 dev_err(&client->dev, "failed to request irq %d\n",
491 client->irq);
492 goto out_failed;
495 chip->gpio_chip.to_irq = max732x_gpio_to_irq;
498 return 0;
500 out_failed:
501 chip->irq_base = 0;
502 return ret;
505 static void max732x_irq_teardown(struct max732x_chip *chip)
507 if (chip->irq_base)
508 free_irq(chip->client->irq, chip);
510 #else /* CONFIG_GPIO_MAX732X_IRQ */
511 static int max732x_irq_setup(struct max732x_chip *chip,
512 const struct i2c_device_id *id)
514 struct i2c_client *client = chip->client;
515 struct max732x_platform_data *pdata = client->dev.platform_data;
516 int has_irq = max732x_features[id->driver_data] >> 32;
518 if (pdata->irq_base && has_irq != INT_NONE)
519 dev_warn(&client->dev, "interrupt support not compiled in\n");
521 return 0;
524 static void max732x_irq_teardown(struct max732x_chip *chip)
527 #endif
529 static int __devinit max732x_setup_gpio(struct max732x_chip *chip,
530 const struct i2c_device_id *id,
531 unsigned gpio_start)
533 struct gpio_chip *gc = &chip->gpio_chip;
534 uint32_t id_data = (uint32_t)max732x_features[id->driver_data];
535 int i, port = 0;
537 for (i = 0; i < 16; i++, id_data >>= 2) {
538 unsigned int mask = 1 << port;
540 switch (id_data & 0x3) {
541 case PORT_OUTPUT:
542 chip->dir_output |= mask;
543 break;
544 case PORT_INPUT:
545 chip->dir_input |= mask;
546 break;
547 case PORT_OPENDRAIN:
548 chip->dir_output |= mask;
549 chip->dir_input |= mask;
550 break;
551 default:
552 continue;
555 if (i < 8)
556 chip->mask_group_a |= mask;
557 port++;
560 if (chip->dir_input)
561 gc->direction_input = max732x_gpio_direction_input;
562 if (chip->dir_output) {
563 gc->direction_output = max732x_gpio_direction_output;
564 gc->set = max732x_gpio_set_value;
566 gc->get = max732x_gpio_get_value;
567 gc->can_sleep = 1;
569 gc->base = gpio_start;
570 gc->ngpio = port;
571 gc->label = chip->client->name;
572 gc->owner = THIS_MODULE;
574 return port;
577 static int __devinit max732x_probe(struct i2c_client *client,
578 const struct i2c_device_id *id)
580 struct max732x_platform_data *pdata;
581 struct max732x_chip *chip;
582 struct i2c_client *c;
583 uint16_t addr_a, addr_b;
584 int ret, nr_port;
586 pdata = client->dev.platform_data;
587 if (pdata == NULL) {
588 dev_dbg(&client->dev, "no platform data\n");
589 return -EINVAL;
592 chip = kzalloc(sizeof(struct max732x_chip), GFP_KERNEL);
593 if (chip == NULL)
594 return -ENOMEM;
595 chip->client = client;
597 nr_port = max732x_setup_gpio(chip, id, pdata->gpio_base);
599 addr_a = (client->addr & 0x0f) | 0x60;
600 addr_b = (client->addr & 0x0f) | 0x50;
602 switch (client->addr & 0x70) {
603 case 0x60:
604 chip->client_group_a = client;
605 if (nr_port > 8) {
606 c = i2c_new_dummy(client->adapter, addr_b);
607 chip->client_group_b = chip->client_dummy = c;
609 break;
610 case 0x50:
611 chip->client_group_b = client;
612 if (nr_port > 8) {
613 c = i2c_new_dummy(client->adapter, addr_a);
614 chip->client_group_a = chip->client_dummy = c;
616 break;
617 default:
618 dev_err(&client->dev, "invalid I2C address specified %02x\n",
619 client->addr);
620 ret = -EINVAL;
621 goto out_failed;
624 mutex_init(&chip->lock);
626 max732x_readb(chip, is_group_a(chip, 0), &chip->reg_out[0]);
627 if (nr_port > 8)
628 max732x_readb(chip, is_group_a(chip, 8), &chip->reg_out[1]);
630 ret = max732x_irq_setup(chip, id);
631 if (ret)
632 goto out_failed;
634 ret = gpiochip_add(&chip->gpio_chip);
635 if (ret)
636 goto out_failed;
638 if (pdata->setup) {
639 ret = pdata->setup(client, chip->gpio_chip.base,
640 chip->gpio_chip.ngpio, pdata->context);
641 if (ret < 0)
642 dev_warn(&client->dev, "setup failed, %d\n", ret);
645 i2c_set_clientdata(client, chip);
646 return 0;
648 out_failed:
649 max732x_irq_teardown(chip);
650 kfree(chip);
651 return ret;
654 static int __devexit max732x_remove(struct i2c_client *client)
656 struct max732x_platform_data *pdata = client->dev.platform_data;
657 struct max732x_chip *chip = i2c_get_clientdata(client);
658 int ret;
660 if (pdata->teardown) {
661 ret = pdata->teardown(client, chip->gpio_chip.base,
662 chip->gpio_chip.ngpio, pdata->context);
663 if (ret < 0) {
664 dev_err(&client->dev, "%s failed, %d\n",
665 "teardown", ret);
666 return ret;
670 ret = gpiochip_remove(&chip->gpio_chip);
671 if (ret) {
672 dev_err(&client->dev, "%s failed, %d\n",
673 "gpiochip_remove()", ret);
674 return ret;
677 max732x_irq_teardown(chip);
679 /* unregister any dummy i2c_client */
680 if (chip->client_dummy)
681 i2c_unregister_device(chip->client_dummy);
683 kfree(chip);
684 return 0;
687 static struct i2c_driver max732x_driver = {
688 .driver = {
689 .name = "max732x",
690 .owner = THIS_MODULE,
692 .probe = max732x_probe,
693 .remove = __devexit_p(max732x_remove),
694 .id_table = max732x_id,
697 static int __init max732x_init(void)
699 return i2c_add_driver(&max732x_driver);
701 /* register after i2c postcore initcall and before
702 * subsys initcalls that may rely on these GPIOs
704 subsys_initcall(max732x_init);
706 static void __exit max732x_exit(void)
708 i2c_del_driver(&max732x_driver);
710 module_exit(max732x_exit);
712 MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>");
713 MODULE_DESCRIPTION("GPIO expander driver for MAX732X");
714 MODULE_LICENSE("GPL");