drivers/ata/pata_pdc202xx_old.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * pata_pdc202xx_old.c  - Promise PDC202xx PATA for new ATA layer
   4  *                        (C) 2005 Red Hat Inc
   5  *                        Alan Cox <alan@lxorguk.ukuu.org.uk>
   6  *                        (C) 2007,2009,2010 Bartlomiej Zolnierkiewicz
   7  *
   8  * Based in part on linux/drivers/ide/pci/pdc202xx_old.c
   9  *
  10  * First cut with LBA48/ATAPI
  11  *
  12  * TODO:
  13  *      Channel interlock/reset on both required ?
  14  */
  15
  16 #include <linux/kernel.h>
  17 #include <linux/module.h>
  18 #include <linux/pci.h>
  19 #include <linux/blkdev.h>
  20 #include <linux/delay.h>
  21 #include <scsi/scsi_host.h>
  22 #include <linux/libata.h>
  23
  24 #define DRV_NAME "pata_pdc202xx_old"
  25 #define DRV_VERSION "0.4.3"
  26
  27 static int pdc2026x_cable_detect(struct ata_port *ap)
  28 {
  29         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  30         u16 cis;
  31
  32         pci_read_config_word(pdev, 0x50, &cis);
  33         if (cis & (1 << (10 + ap->port_no)))
  34                 return ATA_CBL_PATA40;
  35         return ATA_CBL_PATA80;
  36 }
  37
  38 static void pdc202xx_exec_command(struct ata_port *ap,
  39                                   const struct ata_taskfile *tf)
  40 {
  41         DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
  42
  43         iowrite8(tf->command, ap->ioaddr.command_addr);
  44         ndelay(400);
  45 }
  46
  47 static bool pdc202xx_irq_check(struct ata_port *ap)
  48 {
  49         struct pci_dev *pdev    = to_pci_dev(ap->host->dev);
  50         unsigned long master    = pci_resource_start(pdev, 4);
  51         u8 sc1d                 = inb(master + 0x1d);
  52
  53         if (ap->port_no) {
  54                 /*
  55                  * bit 7: error, bit 6: interrupting,
  56                  * bit 5: FIFO full, bit 4: FIFO empty
  57                  */
  58                 return sc1d & 0x40;
  59         } else  {
  60                 /*
  61                  * bit 3: error, bit 2: interrupting,
  62                  * bit 1: FIFO full, bit 0: FIFO empty
  63                  */
  64                 return sc1d & 0x04;
  65         }
  66 }
  67
  68 /**
  69  *      pdc202xx_configure_piomode      -       set chip PIO timing
  70  *      @ap: ATA interface
  71  *      @adev: ATA device
  72  *      @pio: PIO mode
  73  *
  74  *      Called to do the PIO mode setup. Our timing registers are shared
  75  *      so a configure_dmamode call will undo any work we do here and vice
  76  *      versa
  77  */
  78
  79 static void pdc202xx_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
  80 {
  81         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  82         int port = 0x60 + 8 * ap->port_no + 4 * adev->devno;
  83         static u16 pio_timing[5] = {
  84                 0x0913, 0x050C , 0x0308, 0x0206, 0x0104
  85         };
  86         u8 r_ap, r_bp;
  87
  88         pci_read_config_byte(pdev, port, &r_ap);
  89         pci_read_config_byte(pdev, port + 1, &r_bp);
  90         r_ap &= ~0x3F;  /* Preserve ERRDY_EN, SYNC_IN */
  91         r_bp &= ~0x1F;
  92         r_ap |= (pio_timing[pio] >> 8);
  93         r_bp |= (pio_timing[pio] & 0xFF);
  94
  95         if (ata_pio_need_iordy(adev))
  96                 r_ap |= 0x20;   /* IORDY enable */
  97         if (adev->class == ATA_DEV_ATA)
  98                 r_ap |= 0x10;   /* FIFO enable */
  99         pci_write_config_byte(pdev, port, r_ap);
 100         pci_write_config_byte(pdev, port + 1, r_bp);
 101 }
 102
 103 /**
 104  *      pdc202xx_set_piomode    -       set initial PIO mode data
 105  *      @ap: ATA interface
 106  *      @adev: ATA device
 107  *
 108  *      Called to do the PIO mode setup. Our timing registers are shared
 109  *      but we want to set the PIO timing by default.
 110  */
 111
 112 static void pdc202xx_set_piomode(struct ata_port *ap, struct ata_device *adev)
 113 {
 114         pdc202xx_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
 115 }
 116
 117 /**
 118  *      pdc202xx_configure_dmamode      -       set DMA mode in chip
 119  *      @ap: ATA interface
 120  *      @adev: ATA device
 121  *
 122  *      Load DMA cycle times into the chip ready for a DMA transfer
 123  *      to occur.
 124  */
 125
 126 static void pdc202xx_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 127 {
 128         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 129         int port = 0x60 + 8 * ap->port_no + 4 * adev->devno;
 130         static u8 udma_timing[6][2] = {
 131                 { 0x60, 0x03 }, /* 33 Mhz Clock */
 132                 { 0x40, 0x02 },
 133                 { 0x20, 0x01 },
 134                 { 0x40, 0x02 }, /* 66 Mhz Clock */
 135                 { 0x20, 0x01 },
 136                 { 0x20, 0x01 }
 137         };
 138         static u8 mdma_timing[3][2] = {
 139                 { 0xe0, 0x0f },
 140                 { 0x60, 0x04 },
 141                 { 0x60, 0x03 },
 142         };
 143         u8 r_bp, r_cp;
 144
 145         pci_read_config_byte(pdev, port + 1, &r_bp);
 146         pci_read_config_byte(pdev, port + 2, &r_cp);
 147
 148         r_bp &= ~0xE0;
 149         r_cp &= ~0x0F;
 150
 151         if (adev->dma_mode >= XFER_UDMA_0) {
 152                 int speed = adev->dma_mode - XFER_UDMA_0;
 153                 r_bp |= udma_timing[speed][0];
 154                 r_cp |= udma_timing[speed][1];
 155
 156         } else {
 157                 int speed = adev->dma_mode - XFER_MW_DMA_0;
 158                 r_bp |= mdma_timing[speed][0];
 159                 r_cp |= mdma_timing[speed][1];
 160         }
 161         pci_write_config_byte(pdev, port + 1, r_bp);
 162         pci_write_config_byte(pdev, port + 2, r_cp);
 163
 164 }
 165
 166 /**
 167  *      pdc2026x_bmdma_start            -       DMA engine begin
 168  *      @qc: ATA command
 169  *
 170  *      In UDMA3 or higher we have to clock switch for the duration of the
 171  *      DMA transfer sequence.
 172  *
 173  *      Note: The host lock held by the libata layer protects
 174  *      us from two channels both trying to set DMA bits at once
 175  */
 176
 177 static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc)
 178 {
 179         struct ata_port *ap = qc->ap;
 180         struct ata_device *adev = qc->dev;
 181         struct ata_taskfile *tf = &qc->tf;
 182         int sel66 = ap->port_no ? 0x08: 0x02;
 183
 184         void __iomem *master = ap->host->ports[0]->ioaddr.bmdma_addr;
 185         void __iomem *clock = master + 0x11;
 186         void __iomem *atapi_reg = master + 0x20 + (4 * ap->port_no);
 187
 188         u32 len;
 189
 190         /* Check we keep host level locking here */
 191         if (adev->dma_mode > XFER_UDMA_2)
 192                 iowrite8(ioread8(clock) | sel66, clock);
 193         else
 194                 iowrite8(ioread8(clock) & ~sel66, clock);
 195
 196         /* The DMA clocks may have been trashed by a reset. FIXME: make conditional
 197            and move to qc_issue ? */
 198         pdc202xx_set_dmamode(ap, qc->dev);
 199
 200         /* Cases the state machine will not complete correctly without help */
 201         if ((tf->flags & ATA_TFLAG_LBA48) ||  tf->protocol == ATAPI_PROT_DMA) {
 202                 len = qc->nbytes / 2;
 203
 204                 if (tf->flags & ATA_TFLAG_WRITE)
 205                         len |= 0x06000000;
 206                 else
 207                         len |= 0x05000000;
 208
 209                 iowrite32(len, atapi_reg);
 210         }
 211
 212         /* Activate DMA */
 213         ata_bmdma_start(qc);
 214 }
 215
 216 /**
 217  *      pdc2026x_bmdma_end              -       DMA engine stop
 218  *      @qc: ATA command
 219  *
 220  *      After a DMA completes we need to put the clock back to 33MHz for
 221  *      PIO timings.
 222  *
 223  *      Note: The host lock held by the libata layer protects
 224  *      us from two channels both trying to set DMA bits at once
 225  */
 226
 227 static void pdc2026x_bmdma_stop(struct ata_queued_cmd *qc)
 228 {
 229         struct ata_port *ap = qc->ap;
 230         struct ata_device *adev = qc->dev;
 231         struct ata_taskfile *tf = &qc->tf;
 232
 233         int sel66 = ap->port_no ? 0x08: 0x02;
 234         /* The clock bits are in the same register for both channels */
 235         void __iomem *master = ap->host->ports[0]->ioaddr.bmdma_addr;
 236         void __iomem *clock = master + 0x11;
 237         void __iomem *atapi_reg = master + 0x20 + (4 * ap->port_no);
 238
 239         /* Cases the state machine will not complete correctly */
 240         if (tf->protocol == ATAPI_PROT_DMA || (tf->flags & ATA_TFLAG_LBA48)) {
 241                 iowrite32(0, atapi_reg);
 242                 iowrite8(ioread8(clock) & ~sel66, clock);
 243         }
 244         /* Flip back to 33Mhz for PIO */
 245         if (adev->dma_mode > XFER_UDMA_2)
 246                 iowrite8(ioread8(clock) & ~sel66, clock);
 247         ata_bmdma_stop(qc);
 248         pdc202xx_set_piomode(ap, adev);
 249 }
 250
 251 /**
 252  *      pdc2026x_dev_config     -       device setup hook
 253  *      @adev: newly found device
 254  *
 255  *      Perform chip specific early setup. We need to lock the transfer
 256  *      sizes to 8bit to avoid making the state engine on the 2026x cards
 257  *      barf.
 258  */
 259
 260 static void pdc2026x_dev_config(struct ata_device *adev)
 261 {
 262         adev->max_sectors = 256;
 263 }
 264
 265 static int pdc2026x_port_start(struct ata_port *ap)
 266 {
 267         void __iomem *bmdma = ap->ioaddr.bmdma_addr;
 268         if (bmdma) {
 269                 /* Enable burst mode */
 270                 u8 burst = ioread8(bmdma + 0x1f);
 271                 iowrite8(burst | 0x01, bmdma + 0x1f);
 272         }
 273         return ata_bmdma_port_start(ap);
 274 }
 275
 276 /**
 277  *      pdc2026x_check_atapi_dma - Check whether ATAPI DMA can be supported for this command
 278  *      @qc: Metadata associated with taskfile to check
 279  *
 280  *      Just say no - not supported on older Promise.
 281  *
 282  *      LOCKING:
 283  *      None (inherited from caller).
 284  *
 285  *      RETURNS: 0 when ATAPI DMA can be used
 286  *               1 otherwise
 287  */
 288
 289 static int pdc2026x_check_atapi_dma(struct ata_queued_cmd *qc)
 290 {
 291         return 1;
 292 }
 293
 294 static struct scsi_host_template pdc202xx_sht = {
 295         ATA_BMDMA_SHT(DRV_NAME),
 296 };
 297
 298 static struct ata_port_operations pdc2024x_port_ops = {
 299         .inherits               = &ata_bmdma_port_ops,
 300
 301         .cable_detect           = ata_cable_40wire,
 302         .set_piomode            = pdc202xx_set_piomode,
 303         .set_dmamode            = pdc202xx_set_dmamode,
 304
 305         .sff_exec_command       = pdc202xx_exec_command,
 306         .sff_irq_check          = pdc202xx_irq_check,
 307 };
 308
 309 static struct ata_port_operations pdc2026x_port_ops = {
 310         .inherits               = &pdc2024x_port_ops,
 311
 312         .check_atapi_dma        = pdc2026x_check_atapi_dma,
 313         .bmdma_start            = pdc2026x_bmdma_start,
 314         .bmdma_stop             = pdc2026x_bmdma_stop,
 315
 316         .cable_detect           = pdc2026x_cable_detect,
 317         .dev_config             = pdc2026x_dev_config,
 318
 319         .port_start             = pdc2026x_port_start,
 320
 321         .sff_exec_command       = pdc202xx_exec_command,
 322         .sff_irq_check          = pdc202xx_irq_check,
 323 };
 324
 325 static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 326 {
 327         static const struct ata_port_info info[3] = {
 328                 {
 329                         .flags = ATA_FLAG_SLAVE_POSS,
 330                         .pio_mask = ATA_PIO4,
 331                         .mwdma_mask = ATA_MWDMA2,
 332                         .udma_mask = ATA_UDMA2,
 333                         .port_ops = &pdc2024x_port_ops
 334                 },
 335                 {
 336                         .flags = ATA_FLAG_SLAVE_POSS,
 337                         .pio_mask = ATA_PIO4,
 338                         .mwdma_mask = ATA_MWDMA2,
 339                         .udma_mask = ATA_UDMA4,
 340                         .port_ops = &pdc2026x_port_ops
 341                 },
 342                 {
 343                         .flags = ATA_FLAG_SLAVE_POSS,
 344                         .pio_mask = ATA_PIO4,
 345                         .mwdma_mask = ATA_MWDMA2,
 346                         .udma_mask = ATA_UDMA5,
 347                         .port_ops = &pdc2026x_port_ops
 348                 }
 349
 350         };
 351         const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL };
 352
 353         if (dev->device == PCI_DEVICE_ID_PROMISE_20265) {
 354                 struct pci_dev *bridge = dev->bus->self;
 355                 /* Don't grab anything behind a Promise I2O RAID */
 356                 if (bridge && bridge->vendor == PCI_VENDOR_ID_INTEL) {
 357                         if (bridge->device == PCI_DEVICE_ID_INTEL_I960)
 358                                 return -ENODEV;
 359                         if (bridge->device == PCI_DEVICE_ID_INTEL_I960RM)
 360                                 return -ENODEV;
 361                 }
 362         }
 363         return ata_pci_bmdma_init_one(dev, ppi, &pdc202xx_sht, NULL, 0);
 364 }
 365
 366 static const struct pci_device_id pdc202xx[] = {
 367         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0 },
 368         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1 },
 369         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1 },
 370         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2 },
 371         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2 },
 372
 373         { },
 374 };
 375
 376 static struct pci_driver pdc202xx_pci_driver = {
 377         .name           = DRV_NAME,
 378         .id_table       = pdc202xx,
 379         .probe          = pdc202xx_init_one,
 380         .remove         = ata_pci_remove_one,
 381 #ifdef CONFIG_PM_SLEEP
 382         .suspend        = ata_pci_device_suspend,
 383         .resume         = ata_pci_device_resume,
 384 #endif
 385 };
 386
 387 module_pci_driver(pdc202xx_pci_driver);
 388
 389 MODULE_AUTHOR("Alan Cox");
 390 MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267");
 391 MODULE_LICENSE("GPL");
 392 MODULE_DEVICE_TABLE(pci, pdc202xx);
 393 MODULE_VERSION(DRV_VERSION);