drivers/edac/r82600_edac.c

   1 /*
   2  * Radisys 82600 Embedded chipset Memory Controller kernel module
   3  * (C) 2005 EADS Astrium
   4  * This file may be distributed under the terms of the
   5  * GNU General Public License.
   6  *
   7  * Written by Tim Small <tim@buttersideup.com>, based on work by Thayne
   8  * Harbaugh, Dan Hollis <goemon at anime dot net> and others.
   9  *
  10  * $Id: edac_r82600.c,v 1.1.2.6 2005/10/05 00:43:44 dsp_llnl Exp $
  11  *
  12  * Written with reference to 82600 High Integration Dual PCI System
  13  * Controller Data Book:
  14  * www.radisys.com/files/support_downloads/007-01277-0002.82600DataBook.pdf
  15  * references to this document given in []
  16  */
  17
  18 #include <linux/module.h>
  19 #include <linux/init.h>
  20 #include <linux/pci.h>
  21 #include <linux/pci_ids.h>
  22 #include <linux/edac.h>
  23 #include "edac_module.h"
  24
  25 #define EDAC_MOD_STR    "r82600_edac"
  26
  27 #define r82600_printk(level, fmt, arg...) \
  28         edac_printk(level, "r82600", fmt, ##arg)
  29
  30 #define r82600_mc_printk(mci, level, fmt, arg...) \
  31         edac_mc_chipset_printk(mci, level, "r82600", fmt, ##arg)
  32
  33 /* Radisys say "The 82600 integrates a main memory SDRAM controller that
  34  * supports up to four banks of memory. The four banks can support a mix of
  35  * sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs,
  36  * each of which can be any size from 16MB to 512MB. Both registered (control
  37  * signals buffered) and unbuffered DIMM types are supported. Mixing of
  38  * registered and unbuffered DIMMs as well as mixing of ECC and non-ECC DIMMs
  39  * is not allowed. The 82600 SDRAM interface operates at the same frequency as
  40  * the CPU bus, 66MHz, 100MHz or 133MHz."
  41  */
  42
  43 #define R82600_NR_CSROWS 4
  44 #define R82600_NR_CHANS  1
  45 #define R82600_NR_DIMMS  4
  46
  47 #define R82600_BRIDGE_ID  0x8200
  48
  49 /* Radisys 82600 register addresses - device 0 function 0 - PCI bridge */
  50 #define R82600_DRAMC    0x57    /* Various SDRAM related control bits
  51                                  * all bits are R/W
  52                                  *
  53                                  * 7    SDRAM ISA Hole Enable
  54                                  * 6    Flash Page Mode Enable
  55                                  * 5    ECC Enable: 1=ECC 0=noECC
  56                                  * 4    DRAM DIMM Type: 1=
  57                                  * 3    BIOS Alias Disable
  58                                  * 2    SDRAM BIOS Flash Write Enable
  59                                  * 1:0  SDRAM Refresh Rate: 00=Disabled
  60                                  *          01=7.8usec (256Mbit SDRAMs)
  61                                  *          10=15.6us 11=125usec
  62                                  */
  63
  64 #define R82600_SDRAMC   0x76    /* "SDRAM Control Register"
  65                                  * More SDRAM related control bits
  66                                  * all bits are R/W
  67                                  *
  68                                  * 15:8 Reserved.
  69                                  *
  70                                  * 7:5  Special SDRAM Mode Select
  71                                  *
  72                                  * 4    Force ECC
  73                                  *
  74                                  *        1=Drive ECC bits to 0 during
  75                                  *          write cycles (i.e. ECC test mode)
  76                                  *
  77                                  *        0=Normal ECC functioning
  78                                  *
  79                                  * 3    Enhanced Paging Enable
  80                                  *
  81                                  * 2    CAS# Latency 0=3clks 1=2clks
  82                                  *
  83                                  * 1    RAS# to CAS# Delay 0=3 1=2
  84                                  *
  85                                  * 0    RAS# Precharge     0=3 1=2
  86                                  */
  87
  88 #define R82600_EAP      0x80    /* ECC Error Address Pointer Register
  89                                  *
  90                                  * 31    Disable Hardware Scrubbing (RW)
  91                                  *        0=Scrub on corrected read
  92                                  *        1=Don't scrub on corrected read
  93                                  *
  94                                  * 30:12 Error Address Pointer (RO)
  95                                  *        Upper 19 bits of error address
  96                                  *
  97                                  * 11:4  Syndrome Bits (RO)
  98                                  *
  99                                  * 3     BSERR# on multibit error (RW)
 100                                  *        1=enable 0=disable
 101                                  *
 102                                  * 2     NMI on Single Bit Eror (RW)
 103                                  *        1=NMI triggered by SBE n.b. other
 104                                  *          prerequeists
 105                                  *        0=NMI not triggered
 106                                  *
 107                                  * 1     MBE (R/WC)
 108                                  *        read 1=MBE at EAP (see above)
 109                                  *        read 0=no MBE, or SBE occurred first
 110                                  *        write 1=Clear MBE status (must also
 111                                  *          clear SBE)
 112                                  *        write 0=NOP
 113                                  *
 114                                  * 1     SBE (R/WC)
 115                                  *        read 1=SBE at EAP (see above)
 116                                  *        read 0=no SBE, or MBE occurred first
 117                                  *        write 1=Clear SBE status (must also
 118                                  *          clear MBE)
 119                                  *        write 0=NOP
 120                                  */
 121
 122 #define R82600_DRBA     0x60    /* + 0x60..0x63 SDRAM Row Boundary Address
 123                                  *  Registers
 124                                  *
 125                                  * 7:0  Address lines 30:24 - upper limit of
 126                                  * each row [p57]
 127                                  */
 128
 129 struct r82600_error_info {
 130         u32 eapr;
 131 };
 132
 133 static bool disable_hardware_scrub;
 134
 135 static struct edac_pci_ctl_info *r82600_pci;
 136
 137 static void r82600_get_error_info(struct mem_ctl_info *mci,
 138                                 struct r82600_error_info *info)
 139 {
 140         struct pci_dev *pdev;
 141
 142         pdev = to_pci_dev(mci->pdev);
 143         pci_read_config_dword(pdev, R82600_EAP, &info->eapr);
 144
 145         if (info->eapr & BIT(0))
 146                 /* Clear error to allow next error to be reported [p.62] */
 147                 pci_write_bits32(pdev, R82600_EAP,
 148                                  ((u32) BIT(0) & (u32) BIT(1)),
 149                                  ((u32) BIT(0) & (u32) BIT(1)));
 150
 151         if (info->eapr & BIT(1))
 152                 /* Clear error to allow next error to be reported [p.62] */
 153                 pci_write_bits32(pdev, R82600_EAP,
 154                                  ((u32) BIT(0) & (u32) BIT(1)),
 155                                  ((u32) BIT(0) & (u32) BIT(1)));
 156 }
 157
 158 static int r82600_process_error_info(struct mem_ctl_info *mci,
 159                                 struct r82600_error_info *info,
 160                                 int handle_errors)
 161 {
 162         int error_found;
 163         u32 eapaddr, page;
 164         u32 syndrome;
 165
 166         error_found = 0;
 167
 168         /* bits 30:12 store the upper 19 bits of the 32 bit error address */
 169         eapaddr = ((info->eapr >> 12) & 0x7FFF) << 13;
 170         /* Syndrome in bits 11:4 [p.62]       */
 171         syndrome = (info->eapr >> 4) & 0xFF;
 172
 173         /* the R82600 reports at less than page *
 174          * granularity (upper 19 bits only)     */
 175         page = eapaddr >> PAGE_SHIFT;
 176
 177         if (info->eapr & BIT(0)) {      /* CE? */
 178                 error_found = 1;
 179
 180                 if (handle_errors)
 181                         edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci, 1,
 182                                              page, 0, syndrome,
 183                                              edac_mc_find_csrow_by_page(mci, page),
 184                                              0, -1,
 185                                              mci->ctl_name, "");
 186         }
 187
 188         if (info->eapr & BIT(1)) {      /* UE? */
 189                 error_found = 1;
 190
 191                 if (handle_errors)
 192                         /* 82600 doesn't give enough info */
 193                         edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci, 1,
 194                                              page, 0, 0,
 195                                              edac_mc_find_csrow_by_page(mci, page),
 196                                              0, -1,
 197                                              mci->ctl_name, "");
 198         }
 199
 200         return error_found;
 201 }
 202
 203 static void r82600_check(struct mem_ctl_info *mci)
 204 {
 205         struct r82600_error_info info;
 206
 207         r82600_get_error_info(mci, &info);
 208         r82600_process_error_info(mci, &info, 1);
 209 }
 210
 211 static inline int ecc_enabled(u8 dramcr)
 212 {
 213         return dramcr & BIT(5);
 214 }
 215
 216 static void r82600_init_csrows(struct mem_ctl_info *mci, struct pci_dev *pdev,
 217                         u8 dramcr)
 218 {
 219         struct csrow_info *csrow;
 220         struct dimm_info *dimm;
 221         int index;
 222         u8 drbar;               /* SDRAM Row Boundary Address Register */
 223         u32 row_high_limit, row_high_limit_last;
 224         u32 reg_sdram, ecc_on, row_base;
 225
 226         ecc_on = ecc_enabled(dramcr);
 227         reg_sdram = dramcr & BIT(4);
 228         row_high_limit_last = 0;
 229
 230         for (index = 0; index < mci->nr_csrows; index++) {
 231                 csrow = mci->csrows[index];
 232                 dimm = csrow->channels[0]->dimm;
 233
 234                 /* find the DRAM Chip Select Base address and mask */
 235                 pci_read_config_byte(pdev, R82600_DRBA + index, &drbar);
 236
 237                 edac_dbg(1, "Row=%d DRBA = %#0x\n", index, drbar);
 238
 239                 row_high_limit = ((u32) drbar << 24);
 240 /*              row_high_limit = ((u32)drbar << 24) | 0xffffffUL; */
 241
 242                 edac_dbg(1, "Row=%d, Boundary Address=%#0x, Last = %#0x\n",
 243                          index, row_high_limit, row_high_limit_last);
 244
 245                 /* Empty row [p.57] */
 246                 if (row_high_limit == row_high_limit_last)
 247                         continue;
 248
 249                 row_base = row_high_limit_last;
 250
 251                 csrow->first_page = row_base >> PAGE_SHIFT;
 252                 csrow->last_page = (row_high_limit >> PAGE_SHIFT) - 1;
 253
 254                 dimm->nr_pages = csrow->last_page - csrow->first_page + 1;
 255                 /* Error address is top 19 bits - so granularity is      *
 256                  * 14 bits                                               */
 257                 dimm->grain = 1 << 14;
 258                 dimm->mtype = reg_sdram ? MEM_RDDR : MEM_DDR;
 259                 /* FIXME - check that this is unknowable with this chipset */
 260                 dimm->dtype = DEV_UNKNOWN;
 261
 262                 /* Mode is global on 82600 */
 263                 dimm->edac_mode = ecc_on ? EDAC_SECDED : EDAC_NONE;
 264                 row_high_limit_last = row_high_limit;
 265         }
 266 }
 267
 268 static int r82600_probe1(struct pci_dev *pdev, int dev_idx)
 269 {
 270         struct mem_ctl_info *mci;
 271         struct edac_mc_layer layers[2];
 272         u8 dramcr;
 273         u32 eapr;
 274         u32 scrub_disabled;
 275         u32 sdram_refresh_rate;
 276         struct r82600_error_info discard;
 277
 278         edac_dbg(0, "\n");
 279         pci_read_config_byte(pdev, R82600_DRAMC, &dramcr);
 280         pci_read_config_dword(pdev, R82600_EAP, &eapr);
 281         scrub_disabled = eapr & BIT(31);
 282         sdram_refresh_rate = dramcr & (BIT(0) | BIT(1));
 283         edac_dbg(2, "sdram refresh rate = %#0x\n", sdram_refresh_rate);
 284         edac_dbg(2, "DRAMC register = %#0x\n", dramcr);
 285         layers[0].type = EDAC_MC_LAYER_CHIP_SELECT;
 286         layers[0].size = R82600_NR_CSROWS;
 287         layers[0].is_virt_csrow = true;
 288         layers[1].type = EDAC_MC_LAYER_CHANNEL;
 289         layers[1].size = R82600_NR_CHANS;
 290         layers[1].is_virt_csrow = false;
 291         mci = edac_mc_alloc(0, ARRAY_SIZE(layers), layers, 0);
 292         if (mci == NULL)
 293                 return -ENOMEM;
 294
 295         edac_dbg(0, "mci = %p\n", mci);
 296         mci->pdev = &pdev->dev;
 297         mci->mtype_cap = MEM_FLAG_RDDR | MEM_FLAG_DDR;
 298         mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
 299         /* FIXME try to work out if the chip leads have been used for COM2
 300          * instead on this board? [MA6?] MAYBE:
 301          */
 302
 303         /* On the R82600, the pins for memory bits 72:65 - i.e. the   *
 304          * EC bits are shared with the pins for COM2 (!), so if COM2  *
 305          * is enabled, we assume COM2 is wired up, and thus no EDAC   *
 306          * is possible.                                               */
 307         mci->edac_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
 308
 309         if (ecc_enabled(dramcr)) {
 310                 if (scrub_disabled)
 311                         edac_dbg(3, "mci = %p - Scrubbing disabled! EAP: %#0x\n",
 312                                  mci, eapr);
 313         } else
 314                 mci->edac_cap = EDAC_FLAG_NONE;
 315
 316         mci->mod_name = EDAC_MOD_STR;
 317         mci->ctl_name = "R82600";
 318         mci->dev_name = pci_name(pdev);
 319         mci->edac_check = r82600_check;
 320         mci->ctl_page_to_phys = NULL;
 321         r82600_init_csrows(mci, pdev, dramcr);
 322         r82600_get_error_info(mci, &discard);   /* clear counters */
 323
 324         /* Here we assume that we will never see multiple instances of this
 325          * type of memory controller.  The ID is therefore hardcoded to 0.
 326          */
 327         if (edac_mc_add_mc(mci)) {
 328                 edac_dbg(3, "failed edac_mc_add_mc()\n");
 329                 goto fail;
 330         }
 331
 332         /* get this far and it's successful */
 333
 334         if (disable_hardware_scrub) {
 335                 edac_dbg(3, "Disabling Hardware Scrub (scrub on error)\n");
 336                 pci_write_bits32(pdev, R82600_EAP, BIT(31), BIT(31));
 337         }
 338
 339         /* allocating generic PCI control info */
 340         r82600_pci = edac_pci_create_generic_ctl(&pdev->dev, EDAC_MOD_STR);
 341         if (!r82600_pci) {
 342                 printk(KERN_WARNING
 343                         "%s(): Unable to create PCI control\n",
 344                         __func__);
 345                 printk(KERN_WARNING
 346                         "%s(): PCI error report via EDAC not setup\n",
 347                         __func__);
 348         }
 349
 350         edac_dbg(3, "success\n");
 351         return 0;
 352
 353 fail:
 354         edac_mc_free(mci);
 355         return -ENODEV;
 356 }
 357
 358 /* returns count (>= 0), or negative on error */
 359 static int r82600_init_one(struct pci_dev *pdev,
 360                            const struct pci_device_id *ent)
 361 {
 362         edac_dbg(0, "\n");
 363
 364         /* don't need to call pci_enable_device() */
 365         return r82600_probe1(pdev, ent->driver_data);
 366 }
 367
 368 static void r82600_remove_one(struct pci_dev *pdev)
 369 {
 370         struct mem_ctl_info *mci;
 371
 372         edac_dbg(0, "\n");
 373
 374         if (r82600_pci)
 375                 edac_pci_release_generic_ctl(r82600_pci);
 376
 377         if ((mci = edac_mc_del_mc(&pdev->dev)) == NULL)
 378                 return;
 379
 380         edac_mc_free(mci);
 381 }
 382
 383 static const struct pci_device_id r82600_pci_tbl[] = {
 384         {
 385          PCI_DEVICE(PCI_VENDOR_ID_RADISYS, R82600_BRIDGE_ID)
 386          },
 387         {
 388          0,
 389          }                      /* 0 terminated list. */
 390 };
 391
 392 MODULE_DEVICE_TABLE(pci, r82600_pci_tbl);
 393
 394 static struct pci_driver r82600_driver = {
 395         .name = EDAC_MOD_STR,
 396         .probe = r82600_init_one,
 397         .remove = r82600_remove_one,
 398         .id_table = r82600_pci_tbl,
 399 };
 400
 401 static int __init r82600_init(void)
 402 {
 403        /* Ensure that the OPSTATE is set correctly for POLL or NMI */
 404        opstate_init();
 405
 406         return pci_register_driver(&r82600_driver);
 407 }
 408
 409 static void __exit r82600_exit(void)
 410 {
 411         pci_unregister_driver(&r82600_driver);
 412 }
 413
 414 module_init(r82600_init);
 415 module_exit(r82600_exit);
 416
 417 MODULE_LICENSE("GPL");
 418 MODULE_AUTHOR("Tim Small <tim@buttersideup.com> - WPAD Ltd. "
 419                 "on behalf of EADS Astrium");
 420 MODULE_DESCRIPTION("MC support for Radisys 82600 memory controllers");
 421
 422 module_param(disable_hardware_scrub, bool, 0644);
 423 MODULE_PARM_DESC(disable_hardware_scrub,
 424                  "If set, disable the chipset's automatic scrub for CEs");
 425
 426 module_param(edac_op_state, int, 0444);
 427 MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI");