1 // SPDX-License-Identifier: GPL-2.0-or-later
3 Samsung S5H1409 VSB/QAM demodulator driver
5 Copyright (C) 2006 Steven Toth <stoth@linuxtv.org>
10 #include <linux/kernel.h>
11 #include <linux/init.h>
12 #include <linux/module.h>
13 #include <linux/string.h>
14 #include <linux/slab.h>
15 #include <linux/delay.h>
16 #include <media/dvb_frontend.h>
19 struct s5h1409_state
{
21 struct i2c_adapter
*i2c
;
23 /* configuration settings */
24 const struct s5h1409_config
*config
;
26 struct dvb_frontend frontend
;
28 /* previous uncorrected block counter */
29 enum fe_modulation current_modulation
;
31 u32 current_frequency
;
36 /* QAM tuning state goes through the following state transitions */
37 #define QAM_STATE_UNTUNED 0
38 #define QAM_STATE_TUNING_STARTED 1
39 #define QAM_STATE_INTERLEAVE_SET 2
40 #define QAM_STATE_QAM_OPTIMIZED_L1 3
41 #define QAM_STATE_QAM_OPTIMIZED_L2 4
42 #define QAM_STATE_QAM_OPTIMIZED_L3 5
47 module_param(debug
, int, 0644);
48 MODULE_PARM_DESC(debug
, "Enable verbose debug messages");
50 #define dprintk if (debug) printk
52 /* Register values to initialise the demod, this will set VSB by default */
53 static struct init_tab
{
104 /* VSB SNR lookup table */
105 static struct vsb_snr_tab
{
151 /* QAM64 SNR lookup table */
152 static struct qam64_snr_tab
{
155 } qam64_snr_tab
[] = {
223 /* QAM256 SNR lookup table */
224 static struct qam256_snr_tab
{
227 } qam256_snr_tab
[] = {
300 /* 8 bit registers, 16 bit values */
301 static int s5h1409_writereg(struct s5h1409_state
*state
, u8 reg
, u16 data
)
304 u8 buf
[] = { reg
, data
>> 8, data
& 0xff };
306 struct i2c_msg msg
= { .addr
= state
->config
->demod_address
,
307 .flags
= 0, .buf
= buf
, .len
= 3 };
309 ret
= i2c_transfer(state
->i2c
, &msg
, 1);
312 printk(KERN_ERR
"%s: error (reg == 0x%02x, val == 0x%04x, ret == %i)\n",
313 __func__
, reg
, data
, ret
);
315 return (ret
!= 1) ? -1 : 0;
318 static u16
s5h1409_readreg(struct s5h1409_state
*state
, u8 reg
)
324 struct i2c_msg msg
[] = {
325 { .addr
= state
->config
->demod_address
, .flags
= 0,
326 .buf
= b0
, .len
= 1 },
327 { .addr
= state
->config
->demod_address
, .flags
= I2C_M_RD
,
328 .buf
= b1
, .len
= 2 } };
330 ret
= i2c_transfer(state
->i2c
, msg
, 2);
333 printk("%s: readreg error (ret == %i)\n", __func__
, ret
);
334 return (b1
[0] << 8) | b1
[1];
337 static int s5h1409_softreset(struct dvb_frontend
*fe
)
339 struct s5h1409_state
*state
= fe
->demodulator_priv
;
341 dprintk("%s()\n", __func__
);
343 s5h1409_writereg(state
, 0xf5, 0);
344 s5h1409_writereg(state
, 0xf5, 1);
345 state
->is_qam_locked
= 0;
346 state
->qam_state
= QAM_STATE_UNTUNED
;
350 #define S5H1409_VSB_IF_FREQ 5380
351 #define S5H1409_QAM_IF_FREQ (state->config->qam_if)
353 static int s5h1409_set_if_freq(struct dvb_frontend
*fe
, int KHz
)
355 struct s5h1409_state
*state
= fe
->demodulator_priv
;
357 dprintk("%s(%d KHz)\n", __func__
, KHz
);
361 s5h1409_writereg(state
, 0x87, 0x014b);
362 s5h1409_writereg(state
, 0x88, 0x0cb5);
363 s5h1409_writereg(state
, 0x89, 0x03e2);
368 s5h1409_writereg(state
, 0x87, 0x01be);
369 s5h1409_writereg(state
, 0x88, 0x0436);
370 s5h1409_writereg(state
, 0x89, 0x054d);
373 state
->if_freq
= KHz
;
378 static int s5h1409_set_spectralinversion(struct dvb_frontend
*fe
, int inverted
)
380 struct s5h1409_state
*state
= fe
->demodulator_priv
;
382 dprintk("%s(%d)\n", __func__
, inverted
);
385 return s5h1409_writereg(state
, 0x1b, 0x1101); /* Inverted */
387 return s5h1409_writereg(state
, 0x1b, 0x0110); /* Normal */
390 static int s5h1409_enable_modulation(struct dvb_frontend
*fe
,
391 enum fe_modulation m
)
393 struct s5h1409_state
*state
= fe
->demodulator_priv
;
395 dprintk("%s(0x%08x)\n", __func__
, m
);
399 dprintk("%s() VSB_8\n", __func__
);
400 if (state
->if_freq
!= S5H1409_VSB_IF_FREQ
)
401 s5h1409_set_if_freq(fe
, S5H1409_VSB_IF_FREQ
);
402 s5h1409_writereg(state
, 0xf4, 0);
407 dprintk("%s() QAM_AUTO (64/256)\n", __func__
);
408 if (state
->if_freq
!= S5H1409_QAM_IF_FREQ
)
409 s5h1409_set_if_freq(fe
, S5H1409_QAM_IF_FREQ
);
410 s5h1409_writereg(state
, 0xf4, 1);
411 s5h1409_writereg(state
, 0x85, 0x110);
414 dprintk("%s() Invalid modulation\n", __func__
);
418 state
->current_modulation
= m
;
419 s5h1409_softreset(fe
);
424 static int s5h1409_i2c_gate_ctrl(struct dvb_frontend
*fe
, int enable
)
426 struct s5h1409_state
*state
= fe
->demodulator_priv
;
428 dprintk("%s(%d)\n", __func__
, enable
);
431 return s5h1409_writereg(state
, 0xf3, 1);
433 return s5h1409_writereg(state
, 0xf3, 0);
436 static int s5h1409_set_gpio(struct dvb_frontend
*fe
, int enable
)
438 struct s5h1409_state
*state
= fe
->demodulator_priv
;
440 dprintk("%s(%d)\n", __func__
, enable
);
443 return s5h1409_writereg(state
, 0xe3,
444 s5h1409_readreg(state
, 0xe3) | 0x1100);
446 return s5h1409_writereg(state
, 0xe3,
447 s5h1409_readreg(state
, 0xe3) & 0xfeff);
450 static int s5h1409_sleep(struct dvb_frontend
*fe
, int enable
)
452 struct s5h1409_state
*state
= fe
->demodulator_priv
;
454 dprintk("%s(%d)\n", __func__
, enable
);
456 return s5h1409_writereg(state
, 0xf2, enable
);
459 static int s5h1409_register_reset(struct dvb_frontend
*fe
)
461 struct s5h1409_state
*state
= fe
->demodulator_priv
;
463 dprintk("%s()\n", __func__
);
465 return s5h1409_writereg(state
, 0xfa, 0);
468 static void s5h1409_set_qam_amhum_mode(struct dvb_frontend
*fe
)
470 struct s5h1409_state
*state
= fe
->demodulator_priv
;
473 if (state
->qam_state
< QAM_STATE_INTERLEAVE_SET
) {
474 /* We should not perform amhum optimization until
475 the interleave mode has been configured */
479 if (state
->qam_state
== QAM_STATE_QAM_OPTIMIZED_L3
) {
480 /* We've already reached the maximum optimization level, so
481 don't bother banging on the status registers */
485 /* QAM EQ lock check */
486 reg
= s5h1409_readreg(state
, 0xf0);
488 if ((reg
>> 13) & 0x1) {
491 s5h1409_writereg(state
, 0x96, 0x000c);
493 if (state
->qam_state
< QAM_STATE_QAM_OPTIMIZED_L3
) {
494 dprintk("%s() setting QAM state to OPT_L3\n",
496 s5h1409_writereg(state
, 0x93, 0x3130);
497 s5h1409_writereg(state
, 0x9e, 0x2836);
498 state
->qam_state
= QAM_STATE_QAM_OPTIMIZED_L3
;
501 if (state
->qam_state
< QAM_STATE_QAM_OPTIMIZED_L2
) {
502 dprintk("%s() setting QAM state to OPT_L2\n",
504 s5h1409_writereg(state
, 0x93, 0x3332);
505 s5h1409_writereg(state
, 0x9e, 0x2c37);
506 state
->qam_state
= QAM_STATE_QAM_OPTIMIZED_L2
;
511 if (state
->qam_state
< QAM_STATE_QAM_OPTIMIZED_L1
) {
512 dprintk("%s() setting QAM state to OPT_L1\n", __func__
);
513 s5h1409_writereg(state
, 0x96, 0x0008);
514 s5h1409_writereg(state
, 0x93, 0x3332);
515 s5h1409_writereg(state
, 0x9e, 0x2c37);
516 state
->qam_state
= QAM_STATE_QAM_OPTIMIZED_L1
;
521 static void s5h1409_set_qam_amhum_mode_legacy(struct dvb_frontend
*fe
)
523 struct s5h1409_state
*state
= fe
->demodulator_priv
;
526 if (state
->is_qam_locked
)
529 /* QAM EQ lock check */
530 reg
= s5h1409_readreg(state
, 0xf0);
532 if ((reg
>> 13) & 0x1) {
534 state
->is_qam_locked
= 1;
537 s5h1409_writereg(state
, 0x96, 0x00c);
538 if ((reg
< 0x38) || (reg
> 0x68)) {
539 s5h1409_writereg(state
, 0x93, 0x3332);
540 s5h1409_writereg(state
, 0x9e, 0x2c37);
542 s5h1409_writereg(state
, 0x93, 0x3130);
543 s5h1409_writereg(state
, 0x9e, 0x2836);
547 s5h1409_writereg(state
, 0x96, 0x0008);
548 s5h1409_writereg(state
, 0x93, 0x3332);
549 s5h1409_writereg(state
, 0x9e, 0x2c37);
553 static void s5h1409_set_qam_interleave_mode(struct dvb_frontend
*fe
)
555 struct s5h1409_state
*state
= fe
->demodulator_priv
;
558 if (state
->qam_state
>= QAM_STATE_INTERLEAVE_SET
) {
559 /* We've done the optimization already */
563 reg
= s5h1409_readreg(state
, 0xf1);
566 if ((reg
>> 15) & 0x1) {
567 if (state
->qam_state
== QAM_STATE_UNTUNED
||
568 state
->qam_state
== QAM_STATE_TUNING_STARTED
) {
569 dprintk("%s() setting QAM state to INTERLEAVE_SET\n",
571 reg1
= s5h1409_readreg(state
, 0xb2);
572 reg2
= s5h1409_readreg(state
, 0xad);
574 s5h1409_writereg(state
, 0x96, 0x0020);
575 s5h1409_writereg(state
, 0xad,
576 (((reg1
& 0xf000) >> 4) | (reg2
& 0xf0ff)));
577 state
->qam_state
= QAM_STATE_INTERLEAVE_SET
;
580 if (state
->qam_state
== QAM_STATE_UNTUNED
) {
581 dprintk("%s() setting QAM state to TUNING_STARTED\n",
583 s5h1409_writereg(state
, 0x96, 0x08);
584 s5h1409_writereg(state
, 0xab,
585 s5h1409_readreg(state
, 0xab) | 0x1001);
586 state
->qam_state
= QAM_STATE_TUNING_STARTED
;
591 static void s5h1409_set_qam_interleave_mode_legacy(struct dvb_frontend
*fe
)
593 struct s5h1409_state
*state
= fe
->demodulator_priv
;
596 reg
= s5h1409_readreg(state
, 0xf1);
599 if ((reg
>> 15) & 0x1) {
600 if (state
->qam_state
!= 2) {
601 state
->qam_state
= 2;
602 reg1
= s5h1409_readreg(state
, 0xb2);
603 reg2
= s5h1409_readreg(state
, 0xad);
605 s5h1409_writereg(state
, 0x96, 0x20);
606 s5h1409_writereg(state
, 0xad,
607 (((reg1
& 0xf000) >> 4) | (reg2
& 0xf0ff)));
608 s5h1409_writereg(state
, 0xab,
609 s5h1409_readreg(state
, 0xab) & 0xeffe);
612 if (state
->qam_state
!= 1) {
613 state
->qam_state
= 1;
614 s5h1409_writereg(state
, 0x96, 0x08);
615 s5h1409_writereg(state
, 0xab,
616 s5h1409_readreg(state
, 0xab) | 0x1001);
621 /* Talk to the demod, set the FEC, GUARD, QAM settings etc */
622 static int s5h1409_set_frontend(struct dvb_frontend
*fe
)
624 struct dtv_frontend_properties
*p
= &fe
->dtv_property_cache
;
625 struct s5h1409_state
*state
= fe
->demodulator_priv
;
627 dprintk("%s(frequency=%d)\n", __func__
, p
->frequency
);
629 s5h1409_softreset(fe
);
631 state
->current_frequency
= p
->frequency
;
633 s5h1409_enable_modulation(fe
, p
->modulation
);
635 if (fe
->ops
.tuner_ops
.set_params
) {
636 if (fe
->ops
.i2c_gate_ctrl
)
637 fe
->ops
.i2c_gate_ctrl(fe
, 1);
638 fe
->ops
.tuner_ops
.set_params(fe
);
639 if (fe
->ops
.i2c_gate_ctrl
)
640 fe
->ops
.i2c_gate_ctrl(fe
, 0);
643 /* Issue a reset to the demod so it knows to resync against the
644 newly tuned frequency */
645 s5h1409_softreset(fe
);
647 /* Optimize the demod for QAM */
648 if (state
->current_modulation
!= VSB_8
) {
649 /* This almost certainly applies to all boards, but for now
650 only do it for the HVR-1600. Once the other boards are
651 tested, the "legacy" versions can just go away */
652 if (state
->config
->hvr1600_opt
== S5H1409_HVR1600_OPTIMIZE
) {
653 s5h1409_set_qam_interleave_mode(fe
);
654 s5h1409_set_qam_amhum_mode(fe
);
656 s5h1409_set_qam_amhum_mode_legacy(fe
);
657 s5h1409_set_qam_interleave_mode_legacy(fe
);
664 static int s5h1409_set_mpeg_timing(struct dvb_frontend
*fe
, int mode
)
666 struct s5h1409_state
*state
= fe
->demodulator_priv
;
669 dprintk("%s(%d)\n", __func__
, mode
);
671 val
= s5h1409_readreg(state
, 0xac) & 0xcfff;
673 case S5H1409_MPEGTIMING_CONTINUOUS_INVERTING_CLOCK
:
676 case S5H1409_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK
:
677 dprintk("%s(%d) Mode1 or Defaulting\n", __func__
, mode
);
680 case S5H1409_MPEGTIMING_NONCONTINUOUS_INVERTING_CLOCK
:
683 case S5H1409_MPEGTIMING_NONCONTINUOUS_NONINVERTING_CLOCK
:
690 /* Configure MPEG Signal Timing charactistics */
691 return s5h1409_writereg(state
, 0xac, val
);
694 /* Reset the demod hardware and reset all of the configuration registers
695 to a default state. */
696 static int s5h1409_init(struct dvb_frontend
*fe
)
700 struct s5h1409_state
*state
= fe
->demodulator_priv
;
701 dprintk("%s()\n", __func__
);
703 s5h1409_sleep(fe
, 0);
704 s5h1409_register_reset(fe
);
706 for (i
= 0; i
< ARRAY_SIZE(init_tab
); i
++)
707 s5h1409_writereg(state
, init_tab
[i
].reg
, init_tab
[i
].data
);
709 /* The datasheet says that after initialisation, VSB is default */
710 state
->current_modulation
= VSB_8
;
712 /* Optimize for the HVR-1600 if appropriate. Note that some of these
713 may get folded into the generic case after testing with other
715 if (state
->config
->hvr1600_opt
== S5H1409_HVR1600_OPTIMIZE
) {
717 s5h1409_writereg(state
, 0x09, 0x0050);
719 /* Unknown but Windows driver does it... */
720 s5h1409_writereg(state
, 0x21, 0x0001);
721 s5h1409_writereg(state
, 0x50, 0x030e);
724 s5h1409_writereg(state
, 0x82, 0x0800);
727 if (state
->config
->output_mode
== S5H1409_SERIAL_OUTPUT
)
728 s5h1409_writereg(state
, 0xab,
729 s5h1409_readreg(state
, 0xab) | 0x100); /* Serial */
731 s5h1409_writereg(state
, 0xab,
732 s5h1409_readreg(state
, 0xab) & 0xfeff); /* Parallel */
734 s5h1409_set_spectralinversion(fe
, state
->config
->inversion
);
735 s5h1409_set_if_freq(fe
, state
->if_freq
);
736 s5h1409_set_gpio(fe
, state
->config
->gpio
);
737 s5h1409_set_mpeg_timing(fe
, state
->config
->mpeg_timing
);
738 s5h1409_softreset(fe
);
740 /* Note: Leaving the I2C gate closed. */
741 s5h1409_i2c_gate_ctrl(fe
, 0);
746 static int s5h1409_read_status(struct dvb_frontend
*fe
, enum fe_status
*status
)
748 struct s5h1409_state
*state
= fe
->demodulator_priv
;
750 u32 tuner_status
= 0;
754 /* Optimize the demod for QAM */
755 if (state
->current_modulation
!= VSB_8
) {
756 /* This almost certainly applies to all boards, but for now
757 only do it for the HVR-1600. Once the other boards are
758 tested, the "legacy" versions can just go away */
759 if (state
->config
->hvr1600_opt
== S5H1409_HVR1600_OPTIMIZE
) {
760 s5h1409_set_qam_interleave_mode(fe
);
761 s5h1409_set_qam_amhum_mode(fe
);
765 /* Get the demodulator status */
766 reg
= s5h1409_readreg(state
, 0xf1);
768 *status
|= FE_HAS_VITERBI
;
770 *status
|= FE_HAS_LOCK
| FE_HAS_SYNC
;
772 switch (state
->config
->status_mode
) {
773 case S5H1409_DEMODLOCKING
:
774 if (*status
& FE_HAS_VITERBI
)
775 *status
|= FE_HAS_CARRIER
| FE_HAS_SIGNAL
;
777 case S5H1409_TUNERLOCKING
:
778 /* Get the tuner status */
779 if (fe
->ops
.tuner_ops
.get_status
) {
780 if (fe
->ops
.i2c_gate_ctrl
)
781 fe
->ops
.i2c_gate_ctrl(fe
, 1);
783 fe
->ops
.tuner_ops
.get_status(fe
, &tuner_status
);
785 if (fe
->ops
.i2c_gate_ctrl
)
786 fe
->ops
.i2c_gate_ctrl(fe
, 0);
789 *status
|= FE_HAS_CARRIER
| FE_HAS_SIGNAL
;
793 dprintk("%s() status 0x%08x\n", __func__
, *status
);
798 static int s5h1409_qam256_lookup_snr(struct dvb_frontend
*fe
, u16
*snr
, u16 v
)
800 int i
, ret
= -EINVAL
;
801 dprintk("%s()\n", __func__
);
803 for (i
= 0; i
< ARRAY_SIZE(qam256_snr_tab
); i
++) {
804 if (v
< qam256_snr_tab
[i
].val
) {
805 *snr
= qam256_snr_tab
[i
].data
;
813 static int s5h1409_qam64_lookup_snr(struct dvb_frontend
*fe
, u16
*snr
, u16 v
)
815 int i
, ret
= -EINVAL
;
816 dprintk("%s()\n", __func__
);
818 for (i
= 0; i
< ARRAY_SIZE(qam64_snr_tab
); i
++) {
819 if (v
< qam64_snr_tab
[i
].val
) {
820 *snr
= qam64_snr_tab
[i
].data
;
828 static int s5h1409_vsb_lookup_snr(struct dvb_frontend
*fe
, u16
*snr
, u16 v
)
830 int i
, ret
= -EINVAL
;
831 dprintk("%s()\n", __func__
);
833 for (i
= 0; i
< ARRAY_SIZE(vsb_snr_tab
); i
++) {
834 if (v
> vsb_snr_tab
[i
].val
) {
835 *snr
= vsb_snr_tab
[i
].data
;
840 dprintk("%s() snr=%d\n", __func__
, *snr
);
844 static int s5h1409_read_snr(struct dvb_frontend
*fe
, u16
*snr
)
846 struct s5h1409_state
*state
= fe
->demodulator_priv
;
848 dprintk("%s()\n", __func__
);
850 switch (state
->current_modulation
) {
852 reg
= s5h1409_readreg(state
, 0xf0) & 0xff;
853 return s5h1409_qam64_lookup_snr(fe
, snr
, reg
);
855 reg
= s5h1409_readreg(state
, 0xf0) & 0xff;
856 return s5h1409_qam256_lookup_snr(fe
, snr
, reg
);
858 reg
= s5h1409_readreg(state
, 0xf1) & 0x3ff;
859 return s5h1409_vsb_lookup_snr(fe
, snr
, reg
);
867 static int s5h1409_read_signal_strength(struct dvb_frontend
*fe
,
868 u16
*signal_strength
)
870 /* borrowed from lgdt330x.c
872 * Calculate strength from SNR up to 35dB
873 * Even though the SNR can go higher than 35dB,
874 * there is some comfort factor in having a range of
875 * strong signals that can show at 100%
879 int ret
= s5h1409_read_snr(fe
, &snr
);
881 *signal_strength
= 0;
884 /* The following calculation method was chosen
885 * purely for the sake of code re-use from the
886 * other demod drivers that use this method */
888 /* Convert from SNR in dB * 10 to 8.24 fixed-point */
889 tmp
= (snr
* ((1 << 24) / 10));
891 /* Convert from 8.24 fixed-point to
892 * scale the range 0 - 35*2^24 into 0 - 65535*/
893 if (tmp
>= 8960 * 0x10000)
894 *signal_strength
= 0xffff;
896 *signal_strength
= tmp
/ 8960;
902 static int s5h1409_read_ucblocks(struct dvb_frontend
*fe
, u32
*ucblocks
)
904 struct s5h1409_state
*state
= fe
->demodulator_priv
;
906 *ucblocks
= s5h1409_readreg(state
, 0xb5);
911 static int s5h1409_read_ber(struct dvb_frontend
*fe
, u32
*ber
)
913 return s5h1409_read_ucblocks(fe
, ber
);
916 static int s5h1409_get_frontend(struct dvb_frontend
*fe
,
917 struct dtv_frontend_properties
*p
)
919 struct s5h1409_state
*state
= fe
->demodulator_priv
;
921 p
->frequency
= state
->current_frequency
;
922 p
->modulation
= state
->current_modulation
;
927 static int s5h1409_get_tune_settings(struct dvb_frontend
*fe
,
928 struct dvb_frontend_tune_settings
*tune
)
930 tune
->min_delay_ms
= 1000;
934 static void s5h1409_release(struct dvb_frontend
*fe
)
936 struct s5h1409_state
*state
= fe
->demodulator_priv
;
940 static const struct dvb_frontend_ops s5h1409_ops
;
942 struct dvb_frontend
*s5h1409_attach(const struct s5h1409_config
*config
,
943 struct i2c_adapter
*i2c
)
945 struct s5h1409_state
*state
= NULL
;
948 /* allocate memory for the internal state */
949 state
= kzalloc(sizeof(struct s5h1409_state
), GFP_KERNEL
);
953 /* setup the state */
954 state
->config
= config
;
956 state
->current_modulation
= 0;
957 state
->if_freq
= S5H1409_VSB_IF_FREQ
;
959 /* check if the demod exists */
960 reg
= s5h1409_readreg(state
, 0x04);
961 if ((reg
!= 0x0066) && (reg
!= 0x007f))
964 /* create dvb_frontend */
965 memcpy(&state
->frontend
.ops
, &s5h1409_ops
,
966 sizeof(struct dvb_frontend_ops
));
967 state
->frontend
.demodulator_priv
= state
;
969 if (s5h1409_init(&state
->frontend
) != 0) {
970 printk(KERN_ERR
"%s: Failed to initialize correctly\n",
975 /* Note: Leaving the I2C gate open here. */
976 s5h1409_i2c_gate_ctrl(&state
->frontend
, 1);
978 return &state
->frontend
;
984 EXPORT_SYMBOL(s5h1409_attach
);
986 static const struct dvb_frontend_ops s5h1409_ops
= {
987 .delsys
= { SYS_ATSC
, SYS_DVBC_ANNEX_B
},
989 .name
= "Samsung S5H1409 QAM/8VSB Frontend",
990 .frequency_min_hz
= 54 * MHz
,
991 .frequency_max_hz
= 858 * MHz
,
992 .frequency_stepsize_hz
= 62500,
993 .caps
= FE_CAN_QAM_64
| FE_CAN_QAM_256
| FE_CAN_8VSB
996 .init
= s5h1409_init
,
997 .i2c_gate_ctrl
= s5h1409_i2c_gate_ctrl
,
998 .set_frontend
= s5h1409_set_frontend
,
999 .get_frontend
= s5h1409_get_frontend
,
1000 .get_tune_settings
= s5h1409_get_tune_settings
,
1001 .read_status
= s5h1409_read_status
,
1002 .read_ber
= s5h1409_read_ber
,
1003 .read_signal_strength
= s5h1409_read_signal_strength
,
1004 .read_snr
= s5h1409_read_snr
,
1005 .read_ucblocks
= s5h1409_read_ucblocks
,
1006 .release
= s5h1409_release
,
1009 MODULE_DESCRIPTION("Samsung S5H1409 QAM-B/ATSC Demodulator driver");
1010 MODULE_AUTHOR("Steven Toth");
1011 MODULE_LICENSE("GPL");