drivers/net/wireless/ath/ath10k/targaddrs.h

   1 /* SPDX-License-Identifier: ISC */
   2 /*
   3  * Copyright (c) 2005-2011 Atheros Communications Inc.
   4  * Copyright (c) 2011-2016 Qualcomm Atheros, Inc.
   5  */
   6
   7 #ifndef __TARGADDRS_H__
   8 #define __TARGADDRS_H__
   9
  10 #include "hw.h"
  11
  12 /*
  13  * xxx_HOST_INTEREST_ADDRESS is the address in Target RAM of the
  14  * host_interest structure.  It must match the address of the _host_interest
  15  * symbol (see linker script).
  16  *
  17  * Host Interest is shared between Host and Target in order to coordinate
  18  * between the two, and is intended to remain constant (with additions only
  19  * at the end) across software releases.
  20  *
  21  * All addresses are available here so that it's possible to
  22  * write a single binary that works with all Target Types.
  23  * May be used in assembler code as well as C.
  24  */
  25 #define QCA988X_HOST_INTEREST_ADDRESS    0x00400800
  26 #define HOST_INTEREST_MAX_SIZE          0x200
  27
  28 /*
  29  * These are items that the Host may need to access via BMI or via the
  30  * Diagnostic Window. The position of items in this structure must remain
  31  * constant across firmware revisions! Types for each item must be fixed
  32  * size across target and host platforms. More items may be added at the end.
  33  */
  34 struct host_interest {
  35         /*
  36          * Pointer to application-defined area, if any.
  37          * Set by Target application during startup.
  38          */
  39         u32 hi_app_host_interest;                       /* 0x00 */
  40
  41         /* Pointer to register dump area, valid after Target crash. */
  42         u32 hi_failure_state;                           /* 0x04 */
  43
  44         /* Pointer to debug logging header */
  45         u32 hi_dbglog_hdr;                              /* 0x08 */
  46
  47         u32 hi_unused0c;                                /* 0x0c */
  48
  49         /*
  50          * General-purpose flag bits, similar to SOC_OPTION_* flags.
  51          * Can be used by application rather than by OS.
  52          */
  53         u32 hi_option_flag;                             /* 0x10 */
  54
  55         /*
  56          * Boolean that determines whether or not to
  57          * display messages on the serial port.
  58          */
  59         u32 hi_serial_enable;                           /* 0x14 */
  60
  61         /* Start address of DataSet index, if any */
  62         u32 hi_dset_list_head;                          /* 0x18 */
  63
  64         /* Override Target application start address */
  65         u32 hi_app_start;                               /* 0x1c */
  66
  67         /* Clock and voltage tuning */
  68         u32 hi_skip_clock_init;                         /* 0x20 */
  69         u32 hi_core_clock_setting;                      /* 0x24 */
  70         u32 hi_cpu_clock_setting;                       /* 0x28 */
  71         u32 hi_system_sleep_setting;                    /* 0x2c */
  72         u32 hi_xtal_control_setting;                    /* 0x30 */
  73         u32 hi_pll_ctrl_setting_24ghz;                  /* 0x34 */
  74         u32 hi_pll_ctrl_setting_5ghz;                   /* 0x38 */
  75         u32 hi_ref_voltage_trim_setting;                /* 0x3c */
  76         u32 hi_clock_info;                              /* 0x40 */
  77
  78         /* Host uses BE CPU or not */
  79         u32 hi_be;                                      /* 0x44 */
  80
  81         u32 hi_stack;   /* normal stack */                      /* 0x48 */
  82         u32 hi_err_stack; /* error stack */             /* 0x4c */
  83         u32 hi_desired_cpu_speed_hz;                    /* 0x50 */
  84
  85         /* Pointer to Board Data  */
  86         u32 hi_board_data;                              /* 0x54 */
  87
  88         /*
  89          * Indication of Board Data state:
  90          *    0: board data is not yet initialized.
  91          *    1: board data is initialized; unknown size
  92          *   >1: number of bytes of initialized board data
  93          */
  94         u32 hi_board_data_initialized;                  /* 0x58 */
  95
  96         u32 hi_dset_ram_index_table;                    /* 0x5c */
  97
  98         u32 hi_desired_baud_rate;                       /* 0x60 */
  99         u32 hi_dbglog_config;                           /* 0x64 */
 100         u32 hi_end_ram_reserve_sz;                      /* 0x68 */
 101         u32 hi_mbox_io_block_sz;                        /* 0x6c */
 102
 103         u32 hi_num_bpatch_streams;                      /* 0x70 -- unused */
 104         u32 hi_mbox_isr_yield_limit;                    /* 0x74 */
 105
 106         u32 hi_refclk_hz;                               /* 0x78 */
 107         u32 hi_ext_clk_detected;                        /* 0x7c */
 108         u32 hi_dbg_uart_txpin;                          /* 0x80 */
 109         u32 hi_dbg_uart_rxpin;                          /* 0x84 */
 110         u32 hi_hci_uart_baud;                           /* 0x88 */
 111         u32 hi_hci_uart_pin_assignments;                /* 0x8C */
 112
 113         u32 hi_hci_uart_baud_scale_val;                 /* 0x90 */
 114         u32 hi_hci_uart_baud_step_val;                  /* 0x94 */
 115
 116         u32 hi_allocram_start;                          /* 0x98 */
 117         u32 hi_allocram_sz;                             /* 0x9c */
 118         u32 hi_hci_bridge_flags;                        /* 0xa0 */
 119         u32 hi_hci_uart_support_pins;                   /* 0xa4 */
 120
 121         u32 hi_hci_uart_pwr_mgmt_params;                /* 0xa8 */
 122
 123         /*
 124          * 0xa8 - [1]: 0 = UART FC active low, 1 = UART FC active high
 125          *        [31:16]: wakeup timeout in ms
 126          */
 127         /* Pointer to extended board Data  */
 128         u32 hi_board_ext_data;                          /* 0xac */
 129         u32 hi_board_ext_data_config;                   /* 0xb0 */
 130         /*
 131          * Bit [0]  :   valid
 132          * Bit[31:16:   size
 133          */
 134         /*
 135          * hi_reset_flag is used to do some stuff when target reset.
 136          * such as restore app_start after warm reset or
 137          * preserve host Interest area, or preserve ROM data, literals etc.
 138          */
 139         u32  hi_reset_flag;                             /* 0xb4 */
 140         /* indicate hi_reset_flag is valid */
 141         u32  hi_reset_flag_valid;                       /* 0xb8 */
 142         u32 hi_hci_uart_pwr_mgmt_params_ext;            /* 0xbc */
 143         /* 0xbc - [31:0]: idle timeout in ms */
 144         /* ACS flags */
 145         u32 hi_acs_flags;                               /* 0xc0 */
 146         u32 hi_console_flags;                           /* 0xc4 */
 147         u32 hi_nvram_state;                             /* 0xc8 */
 148         u32 hi_option_flag2;                            /* 0xcc */
 149
 150         /* If non-zero, override values sent to Host in WMI_READY event. */
 151         u32 hi_sw_version_override;                     /* 0xd0 */
 152         u32 hi_abi_version_override;                    /* 0xd4 */
 153
 154         /*
 155          * Percentage of high priority RX traffic to total expected RX traffic
 156          * applicable only to ar6004
 157          */
 158         u32 hi_hp_rx_traffic_ratio;                     /* 0xd8 */
 159
 160         /* test applications flags */
 161         u32 hi_test_apps_related;                       /* 0xdc */
 162         /* location of test script */
 163         u32 hi_ota_testscript;                          /* 0xe0 */
 164         /* location of CAL data */
 165         u32 hi_cal_data;                                /* 0xe4 */
 166
 167         /* Number of packet log buffers */
 168         u32 hi_pktlog_num_buffers;                      /* 0xe8 */
 169
 170         /* wow extension configuration */
 171         u32 hi_wow_ext_config;                          /* 0xec */
 172         u32 hi_pwr_save_flags;                          /* 0xf0 */
 173
 174         /* Spatial Multiplexing Power Save (SMPS) options */
 175         u32 hi_smps_options;                            /* 0xf4 */
 176
 177         /* Interconnect-specific state */
 178         u32 hi_interconnect_state;                      /* 0xf8 */
 179
 180         /* Coex configuration flags */
 181         u32 hi_coex_config;                             /* 0xfc */
 182
 183         /* Early allocation support */
 184         u32 hi_early_alloc;                             /* 0x100 */
 185         /* FW swap field */
 186         /*
 187          * Bits of this 32bit word will be used to pass specific swap
 188          * instruction to FW
 189          */
 190         /*
 191          * Bit 0 -- AP Nart descriptor no swap. When this bit is set
 192          * FW will not swap TX descriptor. Meaning packets are formed
 193          * on the target processor.
 194          */
 195         /* Bit 1 - unused */
 196         u32 hi_fw_swap;                                 /* 0x104 */
 197
 198         /* global arenas pointer address, used by host driver debug */
 199         u32 hi_dynamic_mem_arenas_addr;                 /* 0x108 */
 200
 201         /* allocated bytes of DRAM use by allocated */
 202         u32 hi_dynamic_mem_allocated;                   /* 0x10C */
 203
 204         /* remaining bytes of DRAM */
 205         u32 hi_dynamic_mem_remaining;                   /* 0x110 */
 206
 207         /* memory track count, configured by host */
 208         u32 hi_dynamic_mem_track_max;                   /* 0x114 */
 209
 210         /* minidump buffer */
 211         u32 hi_minidump;                                /* 0x118 */
 212
 213         /* bdata's sig and key addr */
 214         u32 hi_bd_sig_key;                              /* 0x11c */
 215 } __packed;
 216
 217 #define HI_ITEM(item)  offsetof(struct host_interest, item)
 218
 219 /* Bits defined in hi_option_flag */
 220
 221 /* Enable timer workaround */
 222 #define HI_OPTION_TIMER_WAR         0x01
 223 /* Limit BMI command credits */
 224 #define HI_OPTION_BMI_CRED_LIMIT    0x02
 225 /* Relay Dot11 hdr to/from host */
 226 #define HI_OPTION_RELAY_DOT11_HDR   0x04
 227 /* MAC addr method 0-locally administred 1-globally unique addrs */
 228 #define HI_OPTION_MAC_ADDR_METHOD   0x08
 229 /* Firmware Bridging */
 230 #define HI_OPTION_FW_BRIDGE         0x10
 231 /* Enable CPU profiling */
 232 #define HI_OPTION_ENABLE_PROFILE    0x20
 233 /* Disable debug logging */
 234 #define HI_OPTION_DISABLE_DBGLOG    0x40
 235 /* Skip Era Tracking */
 236 #define HI_OPTION_SKIP_ERA_TRACKING 0x80
 237 /* Disable PAPRD (debug) */
 238 #define HI_OPTION_PAPRD_DISABLE     0x100
 239 #define HI_OPTION_NUM_DEV_LSB       0x200
 240 #define HI_OPTION_NUM_DEV_MSB       0x800
 241 #define HI_OPTION_DEV_MODE_LSB      0x1000
 242 #define HI_OPTION_DEV_MODE_MSB      0x8000000
 243 /* Disable LowFreq Timer Stabilization */
 244 #define HI_OPTION_NO_LFT_STBL       0x10000000
 245 /* Skip regulatory scan */
 246 #define HI_OPTION_SKIP_REG_SCAN     0x20000000
 247 /*
 248  * Do regulatory scan during init before
 249  * sending WMI ready event to host
 250  */
 251 #define HI_OPTION_INIT_REG_SCAN     0x40000000
 252
 253 /* REV6: Do not adjust memory map */
 254 #define HI_OPTION_SKIP_MEMMAP       0x80000000
 255
 256 #define HI_OPTION_MAC_ADDR_METHOD_SHIFT 3
 257
 258 /* 2 bits of hi_option_flag are used to represent 3 modes */
 259 #define HI_OPTION_FW_MODE_IBSS    0x0 /* IBSS Mode */
 260 #define HI_OPTION_FW_MODE_BSS_STA 0x1 /* STA Mode */
 261 #define HI_OPTION_FW_MODE_AP      0x2 /* AP Mode */
 262 #define HI_OPTION_FW_MODE_BT30AMP 0x3 /* BT30 AMP Mode */
 263
 264 /* 2 bits of hi_option flag are usedto represent 4 submodes */
 265 #define HI_OPTION_FW_SUBMODE_NONE    0x0  /* Normal mode */
 266 #define HI_OPTION_FW_SUBMODE_P2PDEV  0x1  /* p2p device mode */
 267 #define HI_OPTION_FW_SUBMODE_P2PCLIENT 0x2 /* p2p client mode */
 268 #define HI_OPTION_FW_SUBMODE_P2PGO   0x3 /* p2p go mode */
 269
 270 /* Num dev Mask */
 271 #define HI_OPTION_NUM_DEV_MASK    0x7
 272 #define HI_OPTION_NUM_DEV_SHIFT   0x9
 273
 274 /* firmware bridging */
 275 #define HI_OPTION_FW_BRIDGE_SHIFT 0x04
 276
 277 /*
 278  * Fw Mode/SubMode Mask
 279  *-----------------------------------------------------------------------------
 280  *  SUB   |   SUB   |   SUB   |  SUB    |         |         |         |
 281  *MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0]
 282  *  (2)   |   (2)   |   (2)   |   (2)   |   (2)   |   (2)   |   (2)   |   (2)
 283  *-----------------------------------------------------------------------------
 284  */
 285 #define HI_OPTION_FW_MODE_BITS         0x2
 286 #define HI_OPTION_FW_MODE_MASK         0x3
 287 #define HI_OPTION_FW_MODE_SHIFT        0xC
 288 #define HI_OPTION_ALL_FW_MODE_MASK     0xFF
 289
 290 #define HI_OPTION_FW_SUBMODE_BITS      0x2
 291 #define HI_OPTION_FW_SUBMODE_MASK      0x3
 292 #define HI_OPTION_FW_SUBMODE_SHIFT     0x14
 293 #define HI_OPTION_ALL_FW_SUBMODE_MASK  0xFF00
 294 #define HI_OPTION_ALL_FW_SUBMODE_SHIFT 0x8
 295
 296 /* hi_option_flag2 options */
 297 #define HI_OPTION_OFFLOAD_AMSDU     0x01
 298 #define HI_OPTION_DFS_SUPPORT       0x02 /* Enable DFS support */
 299 #define HI_OPTION_ENABLE_RFKILL     0x04 /* RFKill Enable Feature*/
 300 #define HI_OPTION_RADIO_RETENTION_DISABLE 0x08 /* Disable radio retention */
 301 #define HI_OPTION_EARLY_CFG_DONE    0x10 /* Early configuration is complete */
 302
 303 #define HI_OPTION_RF_KILL_SHIFT     0x2
 304 #define HI_OPTION_RF_KILL_MASK      0x1
 305
 306 /* hi_reset_flag */
 307 /* preserve App Start address */
 308 #define HI_RESET_FLAG_PRESERVE_APP_START         0x01
 309 /* preserve host interest */
 310 #define HI_RESET_FLAG_PRESERVE_HOST_INTEREST     0x02
 311 /* preserve ROM data */
 312 #define HI_RESET_FLAG_PRESERVE_ROMDATA           0x04
 313 #define HI_RESET_FLAG_PRESERVE_NVRAM_STATE       0x08
 314 #define HI_RESET_FLAG_PRESERVE_BOOT_INFO         0x10
 315 #define HI_RESET_FLAG_WARM_RESET        0x20
 316
 317 /* define hi_fw_swap bits */
 318 #define HI_DESC_IN_FW_BIT       0x01
 319
 320 /* indicate the reset flag is valid */
 321 #define HI_RESET_FLAG_IS_VALID  0x12345678
 322
 323 /* ACS is enabled */
 324 #define HI_ACS_FLAGS_ENABLED        (1 << 0)
 325 /* Use physical WWAN device */
 326 #define HI_ACS_FLAGS_USE_WWAN       (1 << 1)
 327 /* Use test VAP */
 328 #define HI_ACS_FLAGS_TEST_VAP       (1 << 2)
 329 /* SDIO/mailbox ACS flag definitions */
 330 #define HI_ACS_FLAGS_SDIO_SWAP_MAILBOX_SET       (1 << 0)
 331 #define HI_ACS_FLAGS_SDIO_REDUCE_TX_COMPL_SET    (1 << 1)
 332 #define HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE        (1 << 2)
 333 #define HI_ACS_FLAGS_SDIO_SWAP_MAILBOX_FW_ACK    (1 << 16)
 334 #define HI_ACS_FLAGS_SDIO_REDUCE_TX_COMPL_FW_ACK (1 << 17)
 335
 336 /*
 337  * If both SDIO_CRASH_DUMP_ENHANCEMENT_HOST and SDIO_CRASH_DUMP_ENHANCEMENT_FW
 338  * flags are set, then crashdump upload will be done using the BMI host/target
 339  * communication channel.
 340  */
 341 /* HOST to support using BMI dump FW memory when hit assert */
 342 #define HI_OPTION_SDIO_CRASH_DUMP_ENHANCEMENT_HOST 0x400
 343
 344 /* FW to support using BMI dump FW memory when hit assert */
 345 #define HI_OPTION_SDIO_CRASH_DUMP_ENHANCEMENT_FW   0x800
 346
 347 /*
 348  * CONSOLE FLAGS
 349  *
 350  * Bit Range  Meaning
 351  * ---------  --------------------------------
 352  *   2..0     UART ID (0 = Default)
 353  *    3       Baud Select (0 = 9600, 1 = 115200)
 354  *   30..4    Reserved
 355  *    31      Enable Console
 356  *
 357  */
 358
 359 #define HI_CONSOLE_FLAGS_ENABLE       (1 << 31)
 360 #define HI_CONSOLE_FLAGS_UART_MASK    (0x7)
 361 #define HI_CONSOLE_FLAGS_UART_SHIFT   0
 362 #define HI_CONSOLE_FLAGS_BAUD_SELECT  (1 << 3)
 363
 364 /* SM power save options */
 365 #define HI_SMPS_ALLOW_MASK            (0x00000001)
 366 #define HI_SMPS_MODE_MASK             (0x00000002)
 367 #define HI_SMPS_MODE_STATIC           (0x00000000)
 368 #define HI_SMPS_MODE_DYNAMIC          (0x00000002)
 369 #define HI_SMPS_DISABLE_AUTO_MODE     (0x00000004)
 370 #define HI_SMPS_DATA_THRESH_MASK      (0x000007f8)
 371 #define HI_SMPS_DATA_THRESH_SHIFT     (3)
 372 #define HI_SMPS_RSSI_THRESH_MASK      (0x0007f800)
 373 #define HI_SMPS_RSSI_THRESH_SHIFT     (11)
 374 #define HI_SMPS_LOWPWR_CM_MASK        (0x00380000)
 375 #define HI_SMPS_LOWPWR_CM_SHIFT       (15)
 376 #define HI_SMPS_HIPWR_CM_MASK         (0x03c00000)
 377 #define HI_SMPS_HIPWR_CM_SHIFT        (19)
 378
 379 /*
 380  * WOW Extension configuration
 381  *
 382  * Bit Range  Meaning
 383  * ---------  --------------------------------
 384  *   8..0     Size of each WOW pattern (max 511)
 385  *   15..9    Number of patterns per list (max 127)
 386  *   17..16   Number of lists (max 4)
 387  *   30..18   Reserved
 388  *   31       Enabled
 389  *
 390  *  set values (except enable) to zeros for default settings
 391  */
 392
 393 #define HI_WOW_EXT_ENABLED_MASK        (1 << 31)
 394 #define HI_WOW_EXT_NUM_LIST_SHIFT      16
 395 #define HI_WOW_EXT_NUM_LIST_MASK       (0x3 << HI_WOW_EXT_NUM_LIST_SHIFT)
 396 #define HI_WOW_EXT_NUM_PATTERNS_SHIFT  9
 397 #define HI_WOW_EXT_NUM_PATTERNS_MASK   (0x7F << HI_WOW_EXT_NUM_PATTERNS_SHIFT)
 398 #define HI_WOW_EXT_PATTERN_SIZE_SHIFT  0
 399 #define HI_WOW_EXT_PATTERN_SIZE_MASK   (0x1FF << HI_WOW_EXT_PATTERN_SIZE_SHIFT)
 400
 401 #define HI_WOW_EXT_MAKE_CONFIG(num_lists, count, size) \
 402         ((((num_lists) << HI_WOW_EXT_NUM_LIST_SHIFT) & \
 403                 HI_WOW_EXT_NUM_LIST_MASK) | \
 404         (((count) << HI_WOW_EXT_NUM_PATTERNS_SHIFT) & \
 405                 HI_WOW_EXT_NUM_PATTERNS_MASK) | \
 406         (((size) << HI_WOW_EXT_PATTERN_SIZE_SHIFT) & \
 407                 HI_WOW_EXT_PATTERN_SIZE_MASK))
 408
 409 #define HI_WOW_EXT_GET_NUM_LISTS(config) \
 410         (((config) & HI_WOW_EXT_NUM_LIST_MASK) >> HI_WOW_EXT_NUM_LIST_SHIFT)
 411 #define HI_WOW_EXT_GET_NUM_PATTERNS(config) \
 412         (((config) & HI_WOW_EXT_NUM_PATTERNS_MASK) >> \
 413                 HI_WOW_EXT_NUM_PATTERNS_SHIFT)
 414 #define HI_WOW_EXT_GET_PATTERN_SIZE(config) \
 415         (((config) & HI_WOW_EXT_PATTERN_SIZE_MASK) >> \
 416                 HI_WOW_EXT_PATTERN_SIZE_SHIFT)
 417
 418 /*
 419  * Early allocation configuration
 420  * Support RAM bank configuration before BMI done and this eases the memory
 421  * allocation at very early stage
 422  * Bit Range  Meaning
 423  * ---------  ----------------------------------
 424  * [0:3]      number of bank assigned to be IRAM
 425  * [4:15]     reserved
 426  * [16:31]    magic number
 427  *
 428  * Note:
 429  * 1. target firmware would check magic number and if it's a match, firmware
 430  *    would consider the bits[0:15] are valid and base on that to calculate
 431  *    the end of DRAM. Early allocation would be located at that area and
 432  *    may be reclaimed when necessary
 433  * 2. if no magic number is found, early allocation would happen at "_end"
 434  *    symbol of ROM which is located before the app-data and might NOT be
 435  *    re-claimable. If this is adopted, link script should keep this in
 436  *    mind to avoid data corruption.
 437  */
 438 #define HI_EARLY_ALLOC_MAGIC            0x6d8a
 439 #define HI_EARLY_ALLOC_MAGIC_MASK       0xffff0000
 440 #define HI_EARLY_ALLOC_MAGIC_SHIFT      16
 441 #define HI_EARLY_ALLOC_IRAM_BANKS_MASK  0x0000000f
 442 #define HI_EARLY_ALLOC_IRAM_BANKS_SHIFT 0
 443
 444 #define HI_EARLY_ALLOC_VALID() \
 445         ((((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_MAGIC_MASK) >> \
 446         HI_EARLY_ALLOC_MAGIC_SHIFT) == (HI_EARLY_ALLOC_MAGIC))
 447 #define HI_EARLY_ALLOC_GET_IRAM_BANKS() \
 448         (((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_IRAM_BANKS_MASK) \
 449         >> HI_EARLY_ALLOC_IRAM_BANKS_SHIFT)
 450
 451 /*power save flag bit definitions*/
 452 #define HI_PWR_SAVE_LPL_ENABLED   0x1
 453 /*b1-b3 reserved*/
 454 /*b4-b5 : dev0 LPL type : 0 - none
 455  *                        1- Reduce Pwr Search
 456  *                        2- Reduce Pwr Listen
 457  */
 458 /*b6-b7 : dev1 LPL type and so on for Max 8 devices*/
 459 #define HI_PWR_SAVE_LPL_DEV0_LSB   4
 460 #define HI_PWR_SAVE_LPL_DEV_MASK   0x3
 461 /*power save related utility macros*/
 462 #define HI_LPL_ENABLED() \
 463         ((HOST_INTEREST->hi_pwr_save_flags & HI_PWR_SAVE_LPL_ENABLED))
 464 #define HI_DEV_LPL_TYPE_GET(_devix) \
 465         (HOST_INTEREST->hi_pwr_save_flags & ((HI_PWR_SAVE_LPL_DEV_MASK) << \
 466          (HI_PWR_SAVE_LPL_DEV0_LSB + (_devix) * 2)))
 467
 468 #define HOST_INTEREST_SMPS_IS_ALLOWED() \
 469         ((HOST_INTEREST->hi_smps_options & HI_SMPS_ALLOW_MASK))
 470
 471 /* Reserve 1024 bytes for extended board data */
 472 #define QCA988X_BOARD_DATA_SZ     7168
 473 #define QCA988X_BOARD_EXT_DATA_SZ 0
 474
 475 #define QCA9887_BOARD_DATA_SZ     7168
 476 #define QCA9887_BOARD_EXT_DATA_SZ 0
 477
 478 #define QCA6174_BOARD_DATA_SZ     8192
 479 #define QCA6174_BOARD_EXT_DATA_SZ 0
 480
 481 #define QCA9377_BOARD_DATA_SZ     QCA6174_BOARD_DATA_SZ
 482 #define QCA9377_BOARD_EXT_DATA_SZ 0
 483
 484 #define QCA99X0_BOARD_DATA_SZ     12288
 485 #define QCA99X0_BOARD_EXT_DATA_SZ 0
 486
 487 /* Dual band extended board data */
 488 #define QCA99X0_EXT_BOARD_DATA_SZ 2048
 489 #define EXT_BOARD_ADDRESS_OFFSET 0x3000
 490
 491 #define QCA4019_BOARD_DATA_SZ     12064
 492 #define QCA4019_BOARD_EXT_DATA_SZ 0
 493
 494 #endif /* __TARGADDRS_H__ */