drivers/tty/serial/8250/8250_fintek.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  *  Probe for F81216A LPC to 4 UART
   4  *
   5  *  Copyright (C) 2014-2016 Ricardo Ribalda, Qtechnology A/S
   6  */
   7 #include <linux/module.h>
   8 #include <linux/pci.h>
   9 #include <linux/pnp.h>
  10 #include <linux/kernel.h>
  11 #include <linux/serial_core.h>
  12 #include <linux/irq.h>
  13 #include  "8250.h"
  14
  15 #define ADDR_PORT 0
  16 #define DATA_PORT 1
  17 #define EXIT_KEY 0xAA
  18 #define CHIP_ID1  0x20
  19 #define CHIP_ID2  0x21
  20 #define CHIP_ID_F81865 0x0407
  21 #define CHIP_ID_F81866 0x1010
  22 #define CHIP_ID_F81966 0x0215
  23 #define CHIP_ID_F81216AD 0x1602
  24 #define CHIP_ID_F81216H 0x0501
  25 #define CHIP_ID_F81216 0x0802
  26 #define VENDOR_ID1 0x23
  27 #define VENDOR_ID1_VAL 0x19
  28 #define VENDOR_ID2 0x24
  29 #define VENDOR_ID2_VAL 0x34
  30 #define IO_ADDR1 0x61
  31 #define IO_ADDR2 0x60
  32 #define LDN 0x7
  33
  34 #define FINTEK_IRQ_MODE 0x70
  35 #define IRQ_SHARE       BIT(4)
  36 #define IRQ_MODE_MASK   (BIT(6) | BIT(5))
  37 #define IRQ_LEVEL_LOW   0
  38 #define IRQ_EDGE_HIGH   BIT(5)
  39
  40 /*
  41  * F81216H clock source register, the value and mask is the same with F81866,
  42  * but it's on F0h.
  43  *
  44  * Clock speeds for UART (register F0h)
  45  * 00: 1.8432MHz.
  46  * 01: 18.432MHz.
  47  * 10: 24MHz.
  48  * 11: 14.769MHz.
  49  */
  50 #define RS485  0xF0
  51 #define RTS_INVERT BIT(5)
  52 #define RS485_URA BIT(4)
  53 #define RXW4C_IRA BIT(3)
  54 #define TXW4C_IRA BIT(2)
  55
  56 #define FIFO_CTRL               0xF6
  57 #define FIFO_MODE_MASK          (BIT(1) | BIT(0))
  58 #define FIFO_MODE_128           (BIT(1) | BIT(0))
  59 #define RXFTHR_MODE_MASK        (BIT(5) | BIT(4))
  60 #define RXFTHR_MODE_4X          BIT(5)
  61
  62 #define F81216_LDN_LOW  0x0
  63 #define F81216_LDN_HIGH 0x4
  64
  65 /*
  66  * F81866/966 registers
  67  *
  68  * The IRQ setting mode of F81866/966 is not the same with F81216 series.
  69  *      Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
  70  *      Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
  71  *
  72  * Clock speeds for UART (register F2h)
  73  * 00: 1.8432MHz.
  74  * 01: 18.432MHz.
  75  * 10: 24MHz.
  76  * 11: 14.769MHz.
  77  */
  78 #define F81866_IRQ_MODE         0xf0
  79 #define F81866_IRQ_SHARE        BIT(0)
  80 #define F81866_IRQ_MODE0        BIT(1)
  81
  82 #define F81866_FIFO_CTRL        FIFO_CTRL
  83 #define F81866_IRQ_MODE1        BIT(3)
  84
  85 #define F81866_LDN_LOW          0x10
  86 #define F81866_LDN_HIGH         0x16
  87
  88 #define F81866_UART_CLK 0xF2
  89 #define F81866_UART_CLK_MASK (BIT(1) | BIT(0))
  90 #define F81866_UART_CLK_1_8432MHZ 0
  91 #define F81866_UART_CLK_14_769MHZ (BIT(1) | BIT(0))
  92 #define F81866_UART_CLK_18_432MHZ BIT(0)
  93 #define F81866_UART_CLK_24MHZ BIT(1)
  94
  95 struct fintek_8250 {
  96         u16 pid;
  97         u16 base_port;
  98         u8 index;
  99         u8 key;
 100 };
 101
 102 static u8 sio_read_reg(struct fintek_8250 *pdata, u8 reg)
 103 {
 104         outb(reg, pdata->base_port + ADDR_PORT);
 105         return inb(pdata->base_port + DATA_PORT);
 106 }
 107
 108 static void sio_write_reg(struct fintek_8250 *pdata, u8 reg, u8 data)
 109 {
 110         outb(reg, pdata->base_port + ADDR_PORT);
 111         outb(data, pdata->base_port + DATA_PORT);
 112 }
 113
 114 static void sio_write_mask_reg(struct fintek_8250 *pdata, u8 reg, u8 mask,
 115                                u8 data)
 116 {
 117         u8 tmp;
 118
 119         tmp = (sio_read_reg(pdata, reg) & ~mask) | (mask & data);
 120         sio_write_reg(pdata, reg, tmp);
 121 }
 122
 123 static int fintek_8250_enter_key(u16 base_port, u8 key)
 124 {
 125         if (!request_muxed_region(base_port, 2, "8250_fintek"))
 126                 return -EBUSY;
 127
 128         /* Force to deactive all SuperIO in this base_port */
 129         outb(EXIT_KEY, base_port + ADDR_PORT);
 130
 131         outb(key, base_port + ADDR_PORT);
 132         outb(key, base_port + ADDR_PORT);
 133         return 0;
 134 }
 135
 136 static void fintek_8250_exit_key(u16 base_port)
 137 {
 138
 139         outb(EXIT_KEY, base_port + ADDR_PORT);
 140         release_region(base_port + ADDR_PORT, 2);
 141 }
 142
 143 static int fintek_8250_check_id(struct fintek_8250 *pdata)
 144 {
 145         u16 chip;
 146
 147         if (sio_read_reg(pdata, VENDOR_ID1) != VENDOR_ID1_VAL)
 148                 return -ENODEV;
 149
 150         if (sio_read_reg(pdata, VENDOR_ID2) != VENDOR_ID2_VAL)
 151                 return -ENODEV;
 152
 153         chip = sio_read_reg(pdata, CHIP_ID1);
 154         chip |= sio_read_reg(pdata, CHIP_ID2) << 8;
 155
 156         switch (chip) {
 157         case CHIP_ID_F81865:
 158         case CHIP_ID_F81866:
 159         case CHIP_ID_F81966:
 160         case CHIP_ID_F81216AD:
 161         case CHIP_ID_F81216H:
 162         case CHIP_ID_F81216:
 163                 break;
 164         default:
 165                 return -ENODEV;
 166         }
 167
 168         pdata->pid = chip;
 169         return 0;
 170 }
 171
 172 static int fintek_8250_get_ldn_range(struct fintek_8250 *pdata, int *min,
 173                                      int *max)
 174 {
 175         switch (pdata->pid) {
 176         case CHIP_ID_F81966:
 177         case CHIP_ID_F81865:
 178         case CHIP_ID_F81866:
 179                 *min = F81866_LDN_LOW;
 180                 *max = F81866_LDN_HIGH;
 181                 return 0;
 182
 183         case CHIP_ID_F81216AD:
 184         case CHIP_ID_F81216H:
 185         case CHIP_ID_F81216:
 186                 *min = F81216_LDN_LOW;
 187                 *max = F81216_LDN_HIGH;
 188                 return 0;
 189         }
 190
 191         return -ENODEV;
 192 }
 193
 194 static int fintek_8250_rs485_config(struct uart_port *port,
 195                               struct serial_rs485 *rs485)
 196 {
 197         uint8_t config = 0;
 198         struct fintek_8250 *pdata = port->private_data;
 199
 200         if (!pdata)
 201                 return -EINVAL;
 202
 203         /* Hardware do not support same RTS level on send and receive */
 204         if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
 205                         !(rs485->flags & SER_RS485_RTS_AFTER_SEND))
 206                 return -EINVAL;
 207
 208         if (rs485->flags & SER_RS485_ENABLED) {
 209                 memset(rs485->padding, 0, sizeof(rs485->padding));
 210                 config |= RS485_URA;
 211         } else {
 212                 memset(rs485, 0, sizeof(*rs485));
 213         }
 214
 215         rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
 216                         SER_RS485_RTS_AFTER_SEND;
 217
 218         /* Only the first port supports delays */
 219         if (pdata->index) {
 220                 rs485->delay_rts_before_send = 0;
 221                 rs485->delay_rts_after_send = 0;
 222         }
 223
 224         if (rs485->delay_rts_before_send) {
 225                 rs485->delay_rts_before_send = 1;
 226                 config |= TXW4C_IRA;
 227         }
 228
 229         if (rs485->delay_rts_after_send) {
 230                 rs485->delay_rts_after_send = 1;
 231                 config |= RXW4C_IRA;
 232         }
 233
 234         if (rs485->flags & SER_RS485_RTS_ON_SEND)
 235                 config |= RTS_INVERT;
 236
 237         if (fintek_8250_enter_key(pdata->base_port, pdata->key))
 238                 return -EBUSY;
 239
 240         sio_write_reg(pdata, LDN, pdata->index);
 241         sio_write_reg(pdata, RS485, config);
 242         fintek_8250_exit_key(pdata->base_port);
 243
 244         port->rs485 = *rs485;
 245
 246         return 0;
 247 }
 248
 249 static void fintek_8250_set_irq_mode(struct fintek_8250 *pdata, bool is_level)
 250 {
 251         sio_write_reg(pdata, LDN, pdata->index);
 252
 253         switch (pdata->pid) {
 254         case CHIP_ID_F81966:
 255         case CHIP_ID_F81866:
 256                 sio_write_mask_reg(pdata, F81866_FIFO_CTRL, F81866_IRQ_MODE1,
 257                                    0);
 258                 fallthrough;
 259         case CHIP_ID_F81865:
 260                 sio_write_mask_reg(pdata, F81866_IRQ_MODE, F81866_IRQ_SHARE,
 261                                    F81866_IRQ_SHARE);
 262                 sio_write_mask_reg(pdata, F81866_IRQ_MODE, F81866_IRQ_MODE0,
 263                                    is_level ? 0 : F81866_IRQ_MODE0);
 264                 break;
 265
 266         case CHIP_ID_F81216AD:
 267         case CHIP_ID_F81216H:
 268         case CHIP_ID_F81216:
 269                 sio_write_mask_reg(pdata, FINTEK_IRQ_MODE, IRQ_SHARE,
 270                                    IRQ_SHARE);
 271                 sio_write_mask_reg(pdata, FINTEK_IRQ_MODE, IRQ_MODE_MASK,
 272                                    is_level ? IRQ_LEVEL_LOW : IRQ_EDGE_HIGH);
 273                 break;
 274         }
 275 }
 276
 277 static void fintek_8250_set_max_fifo(struct fintek_8250 *pdata)
 278 {
 279         switch (pdata->pid) {
 280         case CHIP_ID_F81216H: /* 128Bytes FIFO */
 281         case CHIP_ID_F81966:
 282         case CHIP_ID_F81866:
 283                 sio_write_mask_reg(pdata, FIFO_CTRL,
 284                                    FIFO_MODE_MASK | RXFTHR_MODE_MASK,
 285                                    FIFO_MODE_128 | RXFTHR_MODE_4X);
 286                 break;
 287
 288         default: /* Default 16Bytes FIFO */
 289                 break;
 290         }
 291 }
 292
 293 static void fintek_8250_goto_highspeed(struct uart_8250_port *uart,
 294                               struct fintek_8250 *pdata)
 295 {
 296         sio_write_reg(pdata, LDN, pdata->index);
 297
 298         switch (pdata->pid) {
 299         case CHIP_ID_F81966:
 300         case CHIP_ID_F81866: /* set uart clock for high speed serial mode */
 301                 sio_write_mask_reg(pdata, F81866_UART_CLK,
 302                         F81866_UART_CLK_MASK,
 303                         F81866_UART_CLK_14_769MHZ);
 304
 305                 uart->port.uartclk = 921600 * 16;
 306                 break;
 307         default: /* leave clock speed untouched */
 308                 break;
 309         }
 310 }
 311
 312 static void fintek_8250_set_termios(struct uart_port *port,
 313                                     struct ktermios *termios,
 314                                     struct ktermios *old)
 315 {
 316         struct fintek_8250 *pdata = port->private_data;
 317         unsigned int baud = tty_termios_baud_rate(termios);
 318         int i;
 319         u8 reg;
 320         static u32 baudrate_table[] = {115200, 921600, 1152000, 1500000};
 321         static u8 clock_table[] = { F81866_UART_CLK_1_8432MHZ,
 322                         F81866_UART_CLK_14_769MHZ, F81866_UART_CLK_18_432MHZ,
 323                         F81866_UART_CLK_24MHZ };
 324
 325         /*
 326          * We'll use serial8250_do_set_termios() for baud = 0, otherwise It'll
 327          * crash on baudrate_table[i] % baud with "division by zero".
 328          */
 329         if (!baud)
 330                 goto exit;
 331
 332         switch (pdata->pid) {
 333         case CHIP_ID_F81216H:
 334                 reg = RS485;
 335                 break;
 336         case CHIP_ID_F81966:
 337         case CHIP_ID_F81866:
 338                 reg = F81866_UART_CLK;
 339                 break;
 340         default:
 341                 /* Don't change clocksource with unknown PID */
 342                 dev_warn(port->dev,
 343                         "%s: pid: %x Not support. use default set_termios.\n",
 344                         __func__, pdata->pid);
 345                 goto exit;
 346         }
 347
 348         for (i = 0; i < ARRAY_SIZE(baudrate_table); ++i) {
 349                 if (baud > baudrate_table[i] || baudrate_table[i] % baud != 0)
 350                         continue;
 351
 352                 if (port->uartclk == baudrate_table[i] * 16)
 353                         break;
 354
 355                 if (fintek_8250_enter_key(pdata->base_port, pdata->key))
 356                         continue;
 357
 358                 port->uartclk = baudrate_table[i] * 16;
 359
 360                 sio_write_reg(pdata, LDN, pdata->index);
 361                 sio_write_mask_reg(pdata, reg, F81866_UART_CLK_MASK,
 362                                 clock_table[i]);
 363
 364                 fintek_8250_exit_key(pdata->base_port);
 365                 break;
 366         }
 367
 368         if (i == ARRAY_SIZE(baudrate_table)) {
 369                 baud = tty_termios_baud_rate(old);
 370                 tty_termios_encode_baud_rate(termios, baud, baud);
 371         }
 372
 373 exit:
 374         serial8250_do_set_termios(port, termios, old);
 375 }
 376
 377 static void fintek_8250_set_termios_handler(struct uart_8250_port *uart)
 378 {
 379         struct fintek_8250 *pdata = uart->port.private_data;
 380
 381         switch (pdata->pid) {
 382         case CHIP_ID_F81216H:
 383         case CHIP_ID_F81966:
 384         case CHIP_ID_F81866:
 385                 uart->port.set_termios = fintek_8250_set_termios;
 386                 break;
 387
 388         default:
 389                 break;
 390         }
 391 }
 392
 393 static int probe_setup_port(struct fintek_8250 *pdata,
 394                                         struct uart_8250_port *uart)
 395 {
 396         static const u16 addr[] = {0x4e, 0x2e};
 397         static const u8 keys[] = {0x77, 0xa0, 0x87, 0x67};
 398         struct irq_data *irq_data;
 399         bool level_mode = false;
 400         int i, j, k, min, max;
 401
 402         for (i = 0; i < ARRAY_SIZE(addr); i++) {
 403                 for (j = 0; j < ARRAY_SIZE(keys); j++) {
 404                         pdata->base_port = addr[i];
 405                         pdata->key = keys[j];
 406
 407                         if (fintek_8250_enter_key(addr[i], keys[j]))
 408                                 continue;
 409                         if (fintek_8250_check_id(pdata) ||
 410                             fintek_8250_get_ldn_range(pdata, &min, &max)) {
 411                                 fintek_8250_exit_key(addr[i]);
 412                                 continue;
 413                         }
 414
 415                         for (k = min; k < max; k++) {
 416                                 u16 aux;
 417
 418                                 sio_write_reg(pdata, LDN, k);
 419                                 aux = sio_read_reg(pdata, IO_ADDR1);
 420                                 aux |= sio_read_reg(pdata, IO_ADDR2) << 8;
 421                                 if (aux != uart->port.iobase)
 422                                         continue;
 423
 424                                 pdata->index = k;
 425
 426                                 irq_data = irq_get_irq_data(uart->port.irq);
 427                                 if (irq_data)
 428                                         level_mode =
 429                                                 irqd_is_level_type(irq_data);
 430
 431                                 fintek_8250_set_irq_mode(pdata, level_mode);
 432                                 fintek_8250_set_max_fifo(pdata);
 433                                 fintek_8250_goto_highspeed(uart, pdata);
 434
 435                                 fintek_8250_exit_key(addr[i]);
 436
 437                                 return 0;
 438                         }
 439
 440                         fintek_8250_exit_key(addr[i]);
 441                 }
 442         }
 443
 444         return -ENODEV;
 445 }
 446
 447 static void fintek_8250_set_rs485_handler(struct uart_8250_port *uart)
 448 {
 449         struct fintek_8250 *pdata = uart->port.private_data;
 450
 451         switch (pdata->pid) {
 452         case CHIP_ID_F81216AD:
 453         case CHIP_ID_F81216H:
 454         case CHIP_ID_F81966:
 455         case CHIP_ID_F81866:
 456         case CHIP_ID_F81865:
 457                 uart->port.rs485_config = fintek_8250_rs485_config;
 458                 break;
 459
 460         default: /* No RS485 Auto direction functional */
 461                 break;
 462         }
 463 }
 464
 465 int fintek_8250_probe(struct uart_8250_port *uart)
 466 {
 467         struct fintek_8250 *pdata;
 468         struct fintek_8250 probe_data;
 469
 470         if (probe_setup_port(&probe_data, uart))
 471                 return -ENODEV;
 472
 473         pdata = devm_kzalloc(uart->port.dev, sizeof(*pdata), GFP_KERNEL);
 474         if (!pdata)
 475                 return -ENOMEM;
 476
 477         memcpy(pdata, &probe_data, sizeof(probe_data));
 478         uart->port.private_data = pdata;
 479         fintek_8250_set_rs485_handler(uart);
 480         fintek_8250_set_termios_handler(uart);
 481
 482         return 0;
 483 }