drivers/ata/pata_acpi.c

   1 /*
   2  *      ACPI PATA driver
   3  *
   4  *      (c) 2007 Red Hat  <alan@redhat.com>
   5  */
   6
   7 #include <linux/kernel.h>
   8 #include <linux/module.h>
   9 #include <linux/pci.h>
  10 #include <linux/init.h>
  11 #include <linux/blkdev.h>
  12 #include <linux/delay.h>
  13 #include <linux/device.h>
  14 #include <scsi/scsi_host.h>
  15 #include <acpi/acpi_bus.h>
  16 #include <acpi/acnames.h>
  17 #include <acpi/acnamesp.h>
  18 #include <acpi/acparser.h>
  19 #include <acpi/acexcep.h>
  20 #include <acpi/acmacros.h>
  21 #include <acpi/actypes.h>
  22
  23 #include <linux/libata.h>
  24 #include <linux/ata.h>
  25
  26 #define DRV_NAME        "pata_acpi"
  27 #define DRV_VERSION     "0.2.3"
  28
  29 struct pata_acpi {
  30         struct ata_acpi_gtm gtm;
  31         void *last;
  32         unsigned long mask[2];
  33 };
  34
  35 /**
  36  *      pacpi_pre_reset -       check for 40/80 pin
  37  *      @ap: Port
  38  *      @deadline: deadline jiffies for the operation
  39  *
  40  *      Perform the PATA port setup we need.
  41  */
  42
  43 static int pacpi_pre_reset(struct ata_link *link, unsigned long deadline)
  44 {
  45         struct ata_port *ap = link->ap;
  46         struct pata_acpi *acpi = ap->private_data;
  47         if (ap->acpi_handle == NULL || ata_acpi_gtm(ap, &acpi->gtm) < 0)
  48                 return -ENODEV;
  49
  50         return ata_std_prereset(link, deadline);
  51 }
  52
  53 /**
  54  *      pacpi_cable_detect      -       cable type detection
  55  *      @ap: port to detect
  56  *
  57  *      Perform device specific cable detection
  58  */
  59
  60 static int pacpi_cable_detect(struct ata_port *ap)
  61 {
  62         struct pata_acpi *acpi = ap->private_data;
  63
  64         if ((acpi->mask[0] | acpi->mask[1]) & (0xF8 << ATA_SHIFT_UDMA))
  65                 return ATA_CBL_PATA80;
  66         else
  67                 return ATA_CBL_PATA40;
  68 }
  69
  70 /**
  71  *      pacpi_error_handler - Setup and error handler
  72  *      @ap: Port to handle
  73  *
  74  *      LOCKING:
  75  *      None (inherited from caller).
  76  */
  77
  78 static void pacpi_error_handler(struct ata_port *ap)
  79 {
  80         return ata_bmdma_drive_eh(ap, pacpi_pre_reset, ata_std_softreset,
  81                                   NULL, ata_std_postreset);
  82 }
  83
  84 /* Welcome to ACPI, bring a bucket */
  85 static const unsigned int pio_cycle[7] = {
  86         600, 383, 240, 180, 120, 100, 80
  87 };
  88 static const unsigned int mwdma_cycle[5] = {
  89         480, 150, 120, 100, 80
  90 };
  91 static const unsigned int udma_cycle[7] = {
  92         120, 80, 60, 45, 30, 20, 15
  93 };
  94
  95 /**
  96  *      pacpi_discover_modes    -       filter non ACPI modes
  97  *      @adev: ATA device
  98  *      @mask: proposed modes
  99  *
 100  *      Try the modes available and see which ones the ACPI method will
 101  *      set up sensibly. From this we get a mask of ACPI modes we can use
 102  */
 103
 104 static unsigned long pacpi_discover_modes(struct ata_port *ap, struct ata_device *adev)
 105 {
 106         int unit = adev->devno;
 107         struct pata_acpi *acpi = ap->private_data;
 108         int i;
 109         u32 t;
 110         unsigned long mask = (0x7f << ATA_SHIFT_UDMA) | (0x7 << ATA_SHIFT_MWDMA) | (0x1F << ATA_SHIFT_PIO);
 111
 112         struct ata_acpi_gtm probe;
 113
 114         probe = acpi->gtm;
 115
 116         /* We always use the 0 slot for crap hardware */
 117         if (!(probe.flags & 0x10))
 118                 unit = 0;
 119
 120         ata_acpi_gtm(ap, &probe);
 121
 122         /* Start by scanning for PIO modes */
 123         for (i = 0; i < 7; i++) {
 124                 t = probe.drive[unit].pio;
 125                 if (t <= pio_cycle[i]) {
 126                         mask |= (2 << (ATA_SHIFT_PIO + i)) - 1;
 127                         break;
 128                 }
 129         }
 130
 131         /* See if we have MWDMA or UDMA data. We don't bother with MWDMA
 132            if UDMA is availabe as this means the BIOS set UDMA and our
 133            error changedown if it works is UDMA to PIO anyway */
 134         if (probe.flags & (1 << (2 * unit))) {
 135                 /* MWDMA */
 136                 for (i = 0; i < 5; i++) {
 137                         t = probe.drive[unit].dma;
 138                         if (t <= mwdma_cycle[i]) {
 139                                 mask |= (2 << (ATA_SHIFT_MWDMA + i)) - 1;
 140                                 break;
 141                         }
 142                 }
 143         } else {
 144                 /* UDMA */
 145                 for (i = 0; i < 7; i++) {
 146                         t = probe.drive[unit].dma;
 147                         if (t <= udma_cycle[i]) {
 148                                 mask |= (2 << (ATA_SHIFT_UDMA + i)) - 1;
 149                                 break;
 150                         }
 151                 }
 152         }
 153         if (mask & (0xF8 << ATA_SHIFT_UDMA))
 154                 ap->cbl = ATA_CBL_PATA80;
 155         return mask;
 156 }
 157
 158 /**
 159  *      pacpi_mode_filter       -       mode filter for ACPI
 160  *      @adev: device
 161  *      @mask: mask of valid modes
 162  *
 163  *      Filter the valid mode list according to our own specific rules, in
 164  *      this case the list of discovered valid modes obtained by ACPI probing
 165  */
 166
 167 static unsigned long pacpi_mode_filter(struct ata_device *adev, unsigned long mask)
 168 {
 169         struct pata_acpi *acpi = adev->link->ap->private_data;
 170         return ata_pci_default_filter(adev, mask & acpi->mask[adev->devno]);
 171 }
 172
 173 /**
 174  *      pacpi_set_piomode       -       set initial PIO mode data
 175  *      @ap: ATA interface
 176  *      @adev: ATA device
 177  */
 178
 179 static void pacpi_set_piomode(struct ata_port *ap, struct ata_device *adev)
 180 {
 181         int unit = adev->devno;
 182         struct pata_acpi *acpi = ap->private_data;
 183
 184         if (!(acpi->gtm.flags & 0x10))
 185                 unit = 0;
 186
 187         /* Now stuff the nS values into the structure */
 188         acpi->gtm.drive[unit].pio = pio_cycle[adev->pio_mode - XFER_PIO_0];
 189         ata_acpi_stm(ap, &acpi->gtm);
 190         /* See what mode we actually got */
 191         ata_acpi_gtm(ap, &acpi->gtm);
 192 }
 193
 194 /**
 195  *      pacpi_set_dmamode       -       set initial DMA mode data
 196  *      @ap: ATA interface
 197  *      @adev: ATA device
 198  */
 199
 200 static void pacpi_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 201 {
 202         int unit = adev->devno;
 203         struct pata_acpi *acpi = ap->private_data;
 204
 205         if (!(acpi->gtm.flags & 0x10))
 206                 unit = 0;
 207
 208         /* Now stuff the nS values into the structure */
 209         if (adev->dma_mode >= XFER_UDMA_0) {
 210                 acpi->gtm.drive[unit].dma = udma_cycle[adev->dma_mode - XFER_UDMA_0];
 211                 acpi->gtm.flags |= (1 << (2 * unit));
 212         } else {
 213                 acpi->gtm.drive[unit].dma = mwdma_cycle[adev->dma_mode - XFER_MW_DMA_0];
 214                 acpi->gtm.flags &= ~(1 << (2 * unit));
 215         }
 216         ata_acpi_stm(ap, &acpi->gtm);
 217         /* See what mode we actually got */
 218         ata_acpi_gtm(ap, &acpi->gtm);
 219 }
 220
 221 /**
 222  *      pacpi_qc_issue_prot     -       command issue
 223  *      @qc: command pending
 224  *
 225  *      Called when the libata layer is about to issue a command. We wrap
 226  *      this interface so that we can load the correct ATA timings if
 227  *      neccessary.
 228  */
 229
 230 static unsigned int pacpi_qc_issue_prot(struct ata_queued_cmd *qc)
 231 {
 232         struct ata_port *ap = qc->ap;
 233         struct ata_device *adev = qc->dev;
 234         struct pata_acpi *acpi = ap->private_data;
 235
 236         if (acpi->gtm.flags & 0x10)
 237                 return ata_qc_issue_prot(qc);
 238
 239         if (adev != acpi->last) {
 240                 pacpi_set_piomode(ap, adev);
 241                 if (adev->dma_mode)
 242                         pacpi_set_dmamode(ap, adev);
 243                 acpi->last = adev;
 244         }
 245         return ata_qc_issue_prot(qc);
 246 }
 247
 248 /**
 249  *      pacpi_port_start        -       port setup
 250  *      @ap: ATA port being set up
 251  *
 252  *      Use the port_start hook to maintain private control structures
 253  */
 254
 255 static int pacpi_port_start(struct ata_port *ap)
 256 {
 257         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 258         struct pata_acpi *acpi;
 259
 260         int ret;
 261
 262         if (ap->acpi_handle == NULL)
 263                 return -ENODEV;
 264
 265         acpi = ap->private_data = devm_kzalloc(&pdev->dev, sizeof(struct pata_acpi), GFP_KERNEL);
 266         if (ap->private_data == NULL)
 267                 return -ENOMEM;
 268         acpi->mask[0] = pacpi_discover_modes(ap, &ap->link.device[0]);
 269         acpi->mask[1] = pacpi_discover_modes(ap, &ap->link.device[1]);
 270         ret = ata_sff_port_start(ap);
 271         if (ret < 0)
 272                 return ret;
 273
 274         return ret;
 275 }
 276
 277 static struct scsi_host_template pacpi_sht = {
 278         .module                 = THIS_MODULE,
 279         .name                   = DRV_NAME,
 280         .ioctl                  = ata_scsi_ioctl,
 281         .queuecommand           = ata_scsi_queuecmd,
 282         .can_queue              = ATA_DEF_QUEUE,
 283         .this_id                = ATA_SHT_THIS_ID,
 284         .sg_tablesize           = LIBATA_MAX_PRD,
 285         .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
 286         .emulated               = ATA_SHT_EMULATED,
 287         .use_clustering         = ATA_SHT_USE_CLUSTERING,
 288         .proc_name              = DRV_NAME,
 289         .dma_boundary           = ATA_DMA_BOUNDARY,
 290         .slave_configure        = ata_scsi_slave_config,
 291         .slave_destroy          = ata_scsi_slave_destroy,
 292         /* Use standard CHS mapping rules */
 293         .bios_param             = ata_std_bios_param,
 294 };
 295
 296 static const struct ata_port_operations pacpi_ops = {
 297         .set_piomode            = pacpi_set_piomode,
 298         .set_dmamode            = pacpi_set_dmamode,
 299         .mode_filter            = pacpi_mode_filter,
 300
 301         /* Task file is PCI ATA format, use helpers */
 302         .tf_load                = ata_tf_load,
 303         .tf_read                = ata_tf_read,
 304         .check_status           = ata_check_status,
 305         .exec_command           = ata_exec_command,
 306         .dev_select             = ata_std_dev_select,
 307
 308         .freeze                 = ata_bmdma_freeze,
 309         .thaw                   = ata_bmdma_thaw,
 310         .error_handler          = pacpi_error_handler,
 311         .post_internal_cmd      = ata_bmdma_post_internal_cmd,
 312         .cable_detect           = pacpi_cable_detect,
 313
 314         /* BMDMA handling is PCI ATA format, use helpers */
 315         .bmdma_setup            = ata_bmdma_setup,
 316         .bmdma_start            = ata_bmdma_start,
 317         .bmdma_stop             = ata_bmdma_stop,
 318         .bmdma_status           = ata_bmdma_status,
 319         .qc_prep                = ata_qc_prep,
 320         .qc_issue               = pacpi_qc_issue_prot,
 321         .data_xfer              = ata_data_xfer,
 322
 323         /* Timeout handling */
 324         .irq_handler            = ata_interrupt,
 325         .irq_clear              = ata_bmdma_irq_clear,
 326         .irq_on                 = ata_irq_on,
 327
 328         /* Generic PATA PCI ATA helpers */
 329         .port_start             = pacpi_port_start,
 330 };
 331
 332
 333 /**
 334  *      pacpi_init_one - Register ACPI ATA PCI device with kernel services
 335  *      @pdev: PCI device to register
 336  *      @ent: Entry in pacpi_pci_tbl matching with @pdev
 337  *
 338  *      Called from kernel PCI layer.
 339  *
 340  *      LOCKING:
 341  *      Inherited from PCI layer (may sleep).
 342  *
 343  *      RETURNS:
 344  *      Zero on success, or -ERRNO value.
 345  */
 346
 347 static int pacpi_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
 348 {
 349         static const struct ata_port_info info = {
 350                 .sht            = &pacpi_sht,
 351                 .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
 352
 353                 .pio_mask       = 0x1f,
 354                 .mwdma_mask     = 0x07,
 355                 .udma_mask      = 0x7f,
 356
 357                 .port_ops       = &pacpi_ops,
 358         };
 359         const struct ata_port_info *ppi[] = { &info, NULL };
 360         return ata_pci_init_one(pdev, ppi);
 361 }
 362
 363 static const struct pci_device_id pacpi_pci_tbl[] = {
 364         { PCI_ANY_ID,           PCI_ANY_ID,                        PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 1},
 365         { }     /* terminate list */
 366 };
 367
 368 static struct pci_driver pacpi_pci_driver = {
 369         .name                   = DRV_NAME,
 370         .id_table               = pacpi_pci_tbl,
 371         .probe                  = pacpi_init_one,
 372         .remove                 = ata_pci_remove_one,
 373 #ifdef CONFIG_PM
 374         .suspend                = ata_pci_device_suspend,
 375         .resume                 = ata_pci_device_resume,
 376 #endif
 377 };
 378
 379 static int __init pacpi_init(void)
 380 {
 381         return pci_register_driver(&pacpi_pci_driver);
 382 }
 383
 384 static void __exit pacpi_exit(void)
 385 {
 386         pci_unregister_driver(&pacpi_pci_driver);
 387 }
 388
 389 module_init(pacpi_init);
 390 module_exit(pacpi_exit);
 391
 392 MODULE_AUTHOR("Alan Cox");
 393 MODULE_DESCRIPTION("SCSI low-level driver for ATA in ACPI mode");
 394 MODULE_LICENSE("GPL");
 395 MODULE_DEVICE_TABLE(pci, pacpi_pci_tbl);
 396 MODULE_VERSION(DRV_VERSION);
 397