Makefile: Export clang toolchain variables

[linux/fpc-iii.git] / drivers / mfd / ucb1x00-ts.c

/*
 *  Touchscreen driver for UCB1x00-based touchscreens
 *
 *  Copyright (C) 2001 Russell King, All Rights Reserved.
 *  Copyright (C) 2005 Pavel Machek
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * 21-Jan-2002 <jco@ict.es> :
 *
 * Added support for synchronous A/D mode. This mode is useful to
 * avoid noise induced in the touchpanel by the LCD, provided that
 * the UCB1x00 has a valid LCD sync signal routed to its ADCSYNC pin.
 * It is important to note that the signal connected to the ADCSYNC
 * pin should provide pulses even when the LCD is blanked, otherwise
 * a pen touch needed to unblank the LCD will never be read.
 */
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/completion.h>
#include <linux/delay.h>
#include <linux/string.h>
#include <linux/input.h>
#include <linux/device.h>
#include <linux/freezer.h>
#include <linux/slab.h>
#include <linux/kthread.h>
#include <linux/mfd/ucb1x00.h>

#include <mach/collie.h>
#include <asm/mach-types.h>



struct ucb1x00_ts {
        struct input_dev        *idev;
        struct ucb1x00          *ucb;

        spinlock_t              irq_lock;
        unsigned                irq_disabled;
        wait_queue_head_t       irq_wait;
        struct task_struct      *rtask;
        u16                     x_res;
        u16                     y_res;

        unsigned int            adcsync:1;
};

static int adcsync;

static inline void ucb1x00_ts_evt_add(struct ucb1x00_ts *ts, u16 pressure, u16 x, u16 y)
{
        struct input_dev *idev = ts->idev;

        input_report_abs(idev, ABS_X, x);
        input_report_abs(idev, ABS_Y, y);
        input_report_abs(idev, ABS_PRESSURE, pressure);
        input_report_key(idev, BTN_TOUCH, 1);
        input_sync(idev);
}

static inline void ucb1x00_ts_event_release(struct ucb1x00_ts *ts)
{
        struct input_dev *idev = ts->idev;

        input_report_abs(idev, ABS_PRESSURE, 0);
        input_report_key(idev, BTN_TOUCH, 0);
        input_sync(idev);
}

/*
 * Switch to interrupt mode.
 */
static inline void ucb1x00_ts_mode_int(struct ucb1x00_ts *ts)
{
        ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                        UCB_TS_CR_TSMX_POW | UCB_TS_CR_TSPX_POW |
                        UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_GND |
                        UCB_TS_CR_MODE_INT);
}

/*
 * Switch to pressure mode, and read pressure.  We don't need to wait
 * here, since both plates are being driven.
 */
static inline unsigned int ucb1x00_ts_read_pressure(struct ucb1x00_ts *ts)
{
        if (machine_is_collie()) {
                ucb1x00_io_write(ts->ucb, COLLIE_TC35143_GPIO_TBL_CHK, 0);
                ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                                  UCB_TS_CR_TSPX_POW | UCB_TS_CR_TSMX_POW |
                                  UCB_TS_CR_MODE_POS | UCB_TS_CR_BIAS_ENA);

                udelay(55);

                return ucb1x00_adc_read(ts->ucb, UCB_ADC_INP_AD2, ts->adcsync);
        } else {
                ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                                  UCB_TS_CR_TSMX_POW | UCB_TS_CR_TSPX_POW |
                                  UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_GND |
                                  UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);

                return ucb1x00_adc_read(ts->ucb, UCB_ADC_INP_TSPY, ts->adcsync);
        }
}

/*
 * Switch to X position mode and measure Y plate.  We switch the plate
 * configuration in pressure mode, then switch to position mode.  This
 * gives a faster response time.  Even so, we need to wait about 55us
 * for things to stabilise.
 */
static inline unsigned int ucb1x00_ts_read_xpos(struct ucb1x00_ts *ts)
{
        if (machine_is_collie())
                ucb1x00_io_write(ts->ucb, 0, COLLIE_TC35143_GPIO_TBL_CHK);
        else {
                ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                                  UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW |
                                  UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
                ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                                  UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW |
                                  UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
        }
        ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                        UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW |
                        UCB_TS_CR_MODE_POS | UCB_TS_CR_BIAS_ENA);

        udelay(55);

        return ucb1x00_adc_read(ts->ucb, UCB_ADC_INP_TSPY, ts->adcsync);
}

/*
 * Switch to Y position mode and measure X plate.  We switch the plate
 * configuration in pressure mode, then switch to position mode.  This
 * gives a faster response time.  Even so, we need to wait about 55us
 * for things to stabilise.
 */
static inline unsigned int ucb1x00_ts_read_ypos(struct ucb1x00_ts *ts)
{
        if (machine_is_collie())
                ucb1x00_io_write(ts->ucb, 0, COLLIE_TC35143_GPIO_TBL_CHK);
        else {
                ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                                  UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW |
                                  UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
                ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                                  UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW |
                                  UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
        }

        ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                        UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW |
                        UCB_TS_CR_MODE_POS | UCB_TS_CR_BIAS_ENA);

        udelay(55);

        return ucb1x00_adc_read(ts->ucb, UCB_ADC_INP_TSPX, ts->adcsync);
}

/*
 * Switch to X plate resistance mode.  Set MX to ground, PX to
 * supply.  Measure current.
 */
static inline unsigned int ucb1x00_ts_read_xres(struct ucb1x00_ts *ts)
{
        ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                        UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW |
                        UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
        return ucb1x00_adc_read(ts->ucb, 0, ts->adcsync);
}

/*
 * Switch to Y plate resistance mode.  Set MY to ground, PY to
 * supply.  Measure current.
 */
static inline unsigned int ucb1x00_ts_read_yres(struct ucb1x00_ts *ts)
{
        ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
                        UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW |
                        UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
        return ucb1x00_adc_read(ts->ucb, 0, ts->adcsync);
}

static inline int ucb1x00_ts_pen_down(struct ucb1x00_ts *ts)
{
        unsigned int val = ucb1x00_reg_read(ts->ucb, UCB_TS_CR);

        if (machine_is_collie())
                return (!(val & (UCB_TS_CR_TSPX_LOW)));
        else
                return (val & (UCB_TS_CR_TSPX_LOW | UCB_TS_CR_TSMX_LOW));
}

/*
 * This is a RT kernel thread that handles the ADC accesses
 * (mainly so we can use semaphores in the UCB1200 core code
 * to serialise accesses to the ADC).
 */
static int ucb1x00_thread(void *_ts)
{
        struct ucb1x00_ts *ts = _ts;
        DECLARE_WAITQUEUE(wait, current);
        bool frozen, ignore = false;
        int valid = 0;

        set_freezable();
        add_wait_queue(&ts->irq_wait, &wait);
        while (!kthread_freezable_should_stop(&frozen)) {
                unsigned int x, y, p;
                signed long timeout;

                if (frozen)
                        ignore = true;

                ucb1x00_adc_enable(ts->ucb);

                x = ucb1x00_ts_read_xpos(ts);
                y = ucb1x00_ts_read_ypos(ts);
                p = ucb1x00_ts_read_pressure(ts);

                /*
                 * Switch back to interrupt mode.
                 */
                ucb1x00_ts_mode_int(ts);
                ucb1x00_adc_disable(ts->ucb);

                msleep(10);

                ucb1x00_enable(ts->ucb);


                if (ucb1x00_ts_pen_down(ts)) {
                        set_current_state(TASK_INTERRUPTIBLE);

                        spin_lock_irq(&ts->irq_lock);
                        if (ts->irq_disabled) {
                                ts->irq_disabled = 0;
                                enable_irq(ts->ucb->irq_base + UCB_IRQ_TSPX);
                        }
                        spin_unlock_irq(&ts->irq_lock);
                        ucb1x00_disable(ts->ucb);

                        /*
                         * If we spat out a valid sample set last time,
                         * spit out a "pen off" sample here.
                         */
                        if (valid) {
                                ucb1x00_ts_event_release(ts);
                                valid = 0;
                        }

                        timeout = MAX_SCHEDULE_TIMEOUT;
                } else {
                        ucb1x00_disable(ts->ucb);

                        /*
                         * Filtering is policy.  Policy belongs in user
                         * space.  We therefore leave it to user space
                         * to do any filtering they please.
                         */
                        if (!ignore) {
                                ucb1x00_ts_evt_add(ts, p, x, y);
                                valid = 1;
                        }

                        set_current_state(TASK_INTERRUPTIBLE);
                        timeout = HZ / 100;
                }

                schedule_timeout(timeout);
        }

        remove_wait_queue(&ts->irq_wait, &wait);

        ts->rtask = NULL;
        return 0;
}

/*
 * We only detect touch screen _touches_ with this interrupt
 * handler, and even then we just schedule our task.
 */
static irqreturn_t ucb1x00_ts_irq(int irq, void *id)
{
        struct ucb1x00_ts *ts = id;

        spin_lock(&ts->irq_lock);
        ts->irq_disabled = 1;
        disable_irq_nosync(ts->ucb->irq_base + UCB_IRQ_TSPX);
        spin_unlock(&ts->irq_lock);
        wake_up(&ts->irq_wait);

        return IRQ_HANDLED;
}

static int ucb1x00_ts_open(struct input_dev *idev)
{
        struct ucb1x00_ts *ts = input_get_drvdata(idev);
        unsigned long flags = 0;
        int ret = 0;

        BUG_ON(ts->rtask);

        if (machine_is_collie())
                flags = IRQF_TRIGGER_RISING;
        else
                flags = IRQF_TRIGGER_FALLING;

        ts->irq_disabled = 0;

        init_waitqueue_head(&ts->irq_wait);
        ret = request_irq(ts->ucb->irq_base + UCB_IRQ_TSPX, ucb1x00_ts_irq,
                          flags, "ucb1x00-ts", ts);
        if (ret < 0)
                goto out;

        /*
         * If we do this at all, we should allow the user to
         * measure and read the X and Y resistance at any time.
         */
        ucb1x00_adc_enable(ts->ucb);
        ts->x_res = ucb1x00_ts_read_xres(ts);
        ts->y_res = ucb1x00_ts_read_yres(ts);
        ucb1x00_adc_disable(ts->ucb);

        ts->rtask = kthread_run(ucb1x00_thread, ts, "ktsd");
        if (!IS_ERR(ts->rtask)) {
                ret = 0;
        } else {
                free_irq(ts->ucb->irq_base + UCB_IRQ_TSPX, ts);
                ts->rtask = NULL;
                ret = -EFAULT;
        }

 out:
        return ret;
}

/*
 * Release touchscreen resources.  Disable IRQs.
 */
static void ucb1x00_ts_close(struct input_dev *idev)
{
        struct ucb1x00_ts *ts = input_get_drvdata(idev);

        if (ts->rtask)
                kthread_stop(ts->rtask);

        ucb1x00_enable(ts->ucb);
        free_irq(ts->ucb->irq_base + UCB_IRQ_TSPX, ts);
        ucb1x00_reg_write(ts->ucb, UCB_TS_CR, 0);
        ucb1x00_disable(ts->ucb);
}


/*
 * Initialisation.
 */
static int ucb1x00_ts_add(struct ucb1x00_dev *dev)
{
        struct ucb1x00_ts *ts;
        struct input_dev *idev;
        int err;

        ts = kzalloc(sizeof(struct ucb1x00_ts), GFP_KERNEL);
        idev = input_allocate_device();
        if (!ts || !idev) {
                err = -ENOMEM;
                goto fail;
        }

        ts->ucb = dev->ucb;
        ts->idev = idev;
        ts->adcsync = adcsync ? UCB_SYNC : UCB_NOSYNC;
        spin_lock_init(&ts->irq_lock);

        idev->name       = "Touchscreen panel";
        idev->id.product = ts->ucb->id;
        idev->open       = ucb1x00_ts_open;
        idev->close      = ucb1x00_ts_close;
        idev->dev.parent = &ts->ucb->dev;

        idev->evbit[0]   = BIT_MASK(EV_ABS) | BIT_MASK(EV_KEY);
        idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);

        input_set_drvdata(idev, ts);

        ucb1x00_adc_enable(ts->ucb);
        ts->x_res = ucb1x00_ts_read_xres(ts);
        ts->y_res = ucb1x00_ts_read_yres(ts);
        ucb1x00_adc_disable(ts->ucb);

        input_set_abs_params(idev, ABS_X, 0, ts->x_res, 0, 0);
        input_set_abs_params(idev, ABS_Y, 0, ts->y_res, 0, 0);
        input_set_abs_params(idev, ABS_PRESSURE, 0, 0, 0, 0);

        err = input_register_device(idev);
        if (err)
                goto fail;

        dev->priv = ts;

        return 0;

 fail:
        input_free_device(idev);
        kfree(ts);
        return err;
}

static void ucb1x00_ts_remove(struct ucb1x00_dev *dev)
{
        struct ucb1x00_ts *ts = dev->priv;

        input_unregister_device(ts->idev);
        kfree(ts);
}

static struct ucb1x00_driver ucb1x00_ts_driver = {
        .add            = ucb1x00_ts_add,
        .remove         = ucb1x00_ts_remove,
};

static int __init ucb1x00_ts_init(void)
{
        return ucb1x00_register_driver(&ucb1x00_ts_driver);
}

static void __exit ucb1x00_ts_exit(void)
{
        ucb1x00_unregister_driver(&ucb1x00_ts_driver);
}

module_param(adcsync, int, 0444);
module_init(ucb1x00_ts_init);
module_exit(ucb1x00_ts_exit);

MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
MODULE_DESCRIPTION("UCB1x00 touchscreen driver");
MODULE_LICENSE("GPL");