arch/arm/boot/dts/armada-370-rd.dts

   1 /*
   2  * Device Tree file for Marvell Armada 370 Reference Design board
   3  * (RD-88F6710-A1)
   4  *
   5  *  Copied from arch/arm/boot/dts/armada-370-db.dts
   6  *
   7  *  Copyright (C) 2013 Florian Fainelli <florian@openwrt.org>
   8  *
   9  * This file is dual-licensed: you can use it either under the terms
  10  * of the GPL or the X11 license, at your option. Note that this dual
  11  * licensing only applies to this file, and not this project as a
  12  * whole.
  13  *
  14  *  a) This file is free software; you can redistribute it and/or
  15  *     modify it under the terms of the GNU General Public License as
  16  *     published by the Free Software Foundation; either version 2 of the
  17  *     License, or (at your option) any later version.
  18  *
  19  *     This file is distributed in the hope that it will be useful,
  20  *     but WITHOUT ANY WARRANTY; without even the implied warranty of
  21  *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  22  *     GNU General Public License for more details.
  23  *
  24  * Or, alternatively,
  25  *
  26  *  b) Permission is hereby granted, free of charge, to any person
  27  *     obtaining a copy of this software and associated documentation
  28  *     files (the "Software"), to deal in the Software without
  29  *     restriction, including without limitation the rights to use,
  30  *     copy, modify, merge, publish, distribute, sublicense, and/or
  31  *     sell copies of the Software, and to permit persons to whom the
  32  *     Software is furnished to do so, subject to the following
  33  *     conditions:
  34  *
  35  *     The above copyright notice and this permission notice shall be
  36  *     included in all copies or substantial portions of the Software.
  37  *
  38  *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
  39  *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
  40  *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
  41  *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
  42  *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
  43  *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
  44  *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  45  *     OTHER DEALINGS IN THE SOFTWARE.
  46  *
  47  * Note: this Device Tree assumes that the bootloader has remapped the
  48  * internal registers to 0xf1000000 (instead of the default
  49  * 0xd0000000). The 0xf1000000 is the default used by the recent,
  50  * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
  51  * boards were delivered with an older version of the bootloader that
  52  * left internal registers mapped at 0xd0000000. If you are in this
  53  * situation, you should either update your bootloader (preferred
  54  * solution) or the below Device Tree should be adjusted.
  55  */
  56
  57 /dts-v1/;
  58 #include <dt-bindings/input/input.h>
  59 #include <dt-bindings/gpio/gpio.h>
  60 #include "armada-370.dtsi"
  61
  62 / {
  63         model = "Marvell Armada 370 Reference Design";
  64         compatible = "marvell,a370-rd", "marvell,armada370", "marvell,armada-370-xp";
  65
  66         chosen {
  67                 stdout-path = "serial0:115200n8";
  68         };
  69
  70         memory@0 {
  71                 device_type = "memory";
  72                 reg = <0x00000000 0x20000000>; /* 512 MB */
  73         };
  74
  75         soc {
  76                 ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
  77                           MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
  78                           MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
  79
  80                 internal-regs {
  81                         serial@12000 {
  82                                 status = "okay";
  83                         };
  84                         sata@a0000 {
  85                                 nr-ports = <2>;
  86                                 status = "okay";
  87                         };
  88
  89                         ethernet@70000 {
  90                                 status = "okay";
  91                                 phy = <&phy0>;
  92                                 phy-mode = "sgmii";
  93                         };
  94                         ethernet@74000 {
  95                                 pinctrl-0 = <&ge1_rgmii_pins>;
  96                                 pinctrl-names = "default";
  97                                 status = "okay";
  98                                 phy-mode = "rgmii-id";
  99                                 fixed-link {
 100                                            speed = <1000>;
 101                                            full-duplex;
 102                                 };
 103                         };
 104
 105                         mvsdio@d4000 {
 106                                 pinctrl-0 = <&sdio_pins1>;
 107                                 pinctrl-names = "default";
 108                                 status = "okay";
 109                                 /* No CD or WP GPIOs */
 110                                 broken-cd;
 111                         };
 112
 113                         usb@50000 {
 114                                 status = "okay";
 115                         };
 116
 117                         usb@51000 {
 118                                 status = "okay";
 119                         };
 120
 121                         gpio-keys {
 122                                 compatible = "gpio-keys";
 123                                 #address-cells = <1>;
 124                                 #size-cells = <0>;
 125                                 button {
 126                                         label = "Software Button";
 127                                         linux,code = <KEY_POWER>;
 128                                         gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 129                                 };
 130                         };
 131
 132                         gpio-fan {
 133                                 compatible = "gpio-fan";
 134                                 gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
 135                                 gpio-fan,speed-map = <0 0 3000 1>;
 136                                 pinctrl-0 = <&fan_pins>;
 137                                 pinctrl-names = "default";
 138                         };
 139
 140                         gpio_leds {
 141                                 compatible = "gpio-leds";
 142                                 pinctrl-names = "default";
 143                                 pinctrl-0 = <&led_pins>;
 144
 145                                 sw_led {
 146                                         label = "370rd:green:sw";
 147                                         gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 148                                         default-state = "keep";
 149                                 };
 150                         };
 151
 152                         nand@d0000 {
 153                                 status = "okay";
 154                                 num-cs = <1>;
 155                                 marvell,nand-keep-config;
 156                                 marvell,nand-enable-arbiter;
 157                                 nand-on-flash-bbt;
 158
 159                                 partition@0 {
 160                                         label = "U-Boot";
 161                                         reg = <0 0x800000>;
 162                                 };
 163                                 partition@800000 {
 164                                         label = "Linux";
 165                                         reg = <0x800000 0x800000>;
 166                                 };
 167                                 partition@1000000 {
 168                                         label = "Filesystem";
 169                                         reg = <0x1000000 0x3f000000>;
 170                                 };
 171                         };
 172                 };
 173         };
 174
 175         dsa {
 176                 status = "disabled";
 177
 178                 compatible = "marvell,dsa";
 179                 #address-cells = <2>;
 180                 #size-cells = <0>;
 181
 182                 dsa,ethernet = <&eth1>;
 183                 dsa,mii-bus = <&mdio>;
 184
 185                 switch@0 {
 186                         #address-cells = <1>;
 187                         #size-cells = <0>;
 188                         reg = <0x10 0>; /* MDIO address 16, switch 0 in tree */
 189
 190                         port@0 {
 191                                 reg = <0>;
 192                                 label = "lan0";
 193                         };
 194
 195                         port@1 {
 196                                reg = <1>;
 197                                label = "lan1";
 198                         };
 199
 200                         port@2 {
 201                                reg = <2>;
 202                                label = "lan2";
 203                         };
 204
 205                         port@3 {
 206                                reg = <3>;
 207                                label = "lan3";
 208                         };
 209
 210                         port@5 {
 211                               reg = <5>;
 212                               label = "cpu";
 213                         };
 214                 };
 215          };
 216 };
 217
 218 &pciec {
 219         status = "okay";
 220
 221         /* Internal mini-PCIe connector */
 222         pcie@1,0 {
 223                 /* Port 0, Lane 0 */
 224                 status = "okay";
 225         };
 226
 227         /* Internal mini-PCIe connector */
 228         pcie@2,0 {
 229                 /* Port 1, Lane 0 */
 230                 status = "okay";
 231         };
 232 };
 233
 234 &mdio {
 235         pinctrl-0 = <&mdio_pins>;
 236         pinctrl-names = "default";
 237         phy0: ethernet-phy@0 {
 238                 reg = <0>;
 239         };
 240
 241         switch: switch@10 {
 242                 compatible = "marvell,mv88e6085";
 243                 #address-cells = <1>;
 244                 #size-cells = <0>;
 245                 reg = <0x10>;
 246
 247                 ports {
 248                         #address-cells = <1>;
 249                         #size-cells = <0>;
 250
 251                         port@0 {
 252                                 reg = <0>;
 253                                 label = "lan0";
 254                         };
 255
 256                         port@1 {
 257                                reg = <1>;
 258                                label = "lan1";
 259                         };
 260
 261                         port@2 {
 262                                reg = <2>;
 263                                label = "lan2";
 264                         };
 265
 266                         port@3 {
 267                                reg = <3>;
 268                                label = "lan3";
 269                         };
 270
 271                         port@5 {
 272                                 reg = <5>;
 273                                 label = "cpu";
 274                                 ethernet = <&eth1>;
 275                                 fixed-link {
 276                                         speed = <1000>;
 277                                         full-duplex;
 278                                 };
 279                         };
 280                 };
 281         };
 282 };
 283
 284
 285 &pinctrl {
 286         fan_pins: fan-pins {
 287                 marvell,pins = "mpp8";
 288                 marvell,function = "gpio";
 289         };
 290
 291         led_pins: led-pins {
 292                 marvell,pins = "mpp32";
 293                 marvell,function = "gpio";
 294         };
 295 };