arch/m68k/include/asm/MC68328.h

   1
   2 /* include/asm-m68knommu/MC68328.h: '328 control registers
   3  *
   4  * Copyright (C) 1999  Vladimir Gurevich <vgurevic@cisco.com>
   5  *                     Bear & Hare Software, Inc.
   6  *
   7  * Based on include/asm-m68knommu/MC68332.h
   8  * Copyright (C) 1998  Kenneth Albanowski <kjahds@kjahds.com>,
   9  *
  10  */
  11 #include <linux/compiler.h>
  12
  13 #ifndef _MC68328_H_
  14 #define _MC68328_H_
  15
  16 #define BYTE_REF(addr) (*((volatile unsigned char*)addr))
  17 #define WORD_REF(addr) (*((volatile unsigned short*)addr))
  18 #define LONG_REF(addr) (*((volatile unsigned long*)addr))
  19
  20 #define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK)
  21 #define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT)
  22
  23 /**********
  24  *
  25  * 0xFFFFF0xx -- System Control
  26  *
  27  **********/
  28
  29 /*
  30  * System Control Register (SCR)
  31  */
  32 #define SCR_ADDR        0xfffff000
  33 #define SCR             BYTE_REF(SCR_ADDR)
  34
  35 #define SCR_WDTH8       0x01    /* 8-Bit Width Select */
  36 #define SCR_DMAP        0x04    /* Double Map */
  37 #define SCR_SO          0x08    /* Supervisor Only */
  38 #define SCR_BETEN       0x10    /* Bus-Error Time-Out Enable */
  39 #define SCR_PRV         0x20    /* Privilege Violation */
  40 #define SCR_WPV         0x40    /* Write Protect Violation */
  41 #define SCR_BETO        0x80    /* Bus-Error TimeOut */
  42
  43 /*
  44  * Mask Revision Register
  45  */
  46 #define MRR_ADDR 0xfffff004
  47 #define MRR      LONG_REF(MRR_ADDR)
  48
  49 /**********
  50  *
  51  * 0xFFFFF1xx -- Chip-Select logic
  52  *
  53  **********/
  54
  55 /**********
  56  *
  57  * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control
  58  *
  59  **********/
  60
  61 /*
  62  * Group Base Address Registers
  63  */
  64 #define GRPBASEA_ADDR   0xfffff100
  65 #define GRPBASEB_ADDR   0xfffff102
  66 #define GRPBASEC_ADDR   0xfffff104
  67 #define GRPBASED_ADDR   0xfffff106
  68
  69 #define GRPBASEA        WORD_REF(GRPBASEA_ADDR)
  70 #define GRPBASEB        WORD_REF(GRPBASEB_ADDR)
  71 #define GRPBASEC        WORD_REF(GRPBASEC_ADDR)
  72 #define GRPBASED        WORD_REF(GRPBASED_ADDR)
  73
  74 #define GRPBASE_V         0x0001        /* Valid */
  75 #define GRPBASE_GBA_MASK  0xfff0        /* Group Base Address (bits 31-20) */
  76
  77 /*
  78  * Group Base Address Mask Registers
  79  */
  80 #define GRPMASKA_ADDR   0xfffff108
  81 #define GRPMASKB_ADDR   0xfffff10a
  82 #define GRPMASKC_ADDR   0xfffff10c
  83 #define GRPMASKD_ADDR   0xfffff10e
  84
  85 #define GRPMASKA        WORD_REF(GRPMASKA_ADDR)
  86 #define GRPMASKB        WORD_REF(GRPMASKB_ADDR)
  87 #define GRPMASKC        WORD_REF(GRPMASKC_ADDR)
  88 #define GRPMASKD        WORD_REF(GRPMASKD_ADDR)
  89
  90 #define GRMMASK_GMA_MASK 0xfffff0       /* Group Base Mask (bits 31-20) */
  91
  92 /*
  93  * Chip-Select Option Registers (group A)
  94  */
  95 #define CSA0_ADDR       0xfffff110
  96 #define CSA1_ADDR       0xfffff114
  97 #define CSA2_ADDR       0xfffff118
  98 #define CSA3_ADDR       0xfffff11c
  99
 100 #define CSA0            LONG_REF(CSA0_ADDR)
 101 #define CSA1            LONG_REF(CSA1_ADDR)
 102 #define CSA2            LONG_REF(CSA2_ADDR)
 103 #define CSA3            LONG_REF(CSA3_ADDR)
 104
 105 #define CSA_WAIT_MASK   0x00000007      /* Wait State Selection */
 106 #define CSA_WAIT_SHIFT  0
 107 #define CSA_RO          0x00000008      /* Read-Only */
 108 #define CSA_AM_MASK     0x0000ff00      /* Address Mask (bits 23-16) */
 109 #define CSA_AM_SHIFT    8
 110 #define CSA_BUSW        0x00010000      /* Bus Width Select */
 111 #define CSA_AC_MASK     0xff000000      /* Address Compare (bits 23-16) */
 112 #define CSA_AC_SHIFT    24
 113
 114 /*
 115  * Chip-Select Option Registers (group B)
 116  */
 117 #define CSB0_ADDR       0xfffff120
 118 #define CSB1_ADDR       0xfffff124
 119 #define CSB2_ADDR       0xfffff128
 120 #define CSB3_ADDR       0xfffff12c
 121
 122 #define CSB0            LONG_REF(CSB0_ADDR)
 123 #define CSB1            LONG_REF(CSB1_ADDR)
 124 #define CSB2            LONG_REF(CSB2_ADDR)
 125 #define CSB3            LONG_REF(CSB3_ADDR)
 126
 127 #define CSB_WAIT_MASK   0x00000007      /* Wait State Selection */
 128 #define CSB_WAIT_SHIFT  0
 129 #define CSB_RO          0x00000008      /* Read-Only */
 130 #define CSB_AM_MASK     0x0000ff00      /* Address Mask (bits 23-16) */
 131 #define CSB_AM_SHIFT    8
 132 #define CSB_BUSW        0x00010000      /* Bus Width Select */
 133 #define CSB_AC_MASK     0xff000000      /* Address Compare (bits 23-16) */
 134 #define CSB_AC_SHIFT    24
 135
 136 /*
 137  * Chip-Select Option Registers (group C)
 138  */
 139 #define CSC0_ADDR       0xfffff130
 140 #define CSC1_ADDR       0xfffff134
 141 #define CSC2_ADDR       0xfffff138
 142 #define CSC3_ADDR       0xfffff13c
 143
 144 #define CSC0            LONG_REF(CSC0_ADDR)
 145 #define CSC1            LONG_REF(CSC1_ADDR)
 146 #define CSC2            LONG_REF(CSC2_ADDR)
 147 #define CSC3            LONG_REF(CSC3_ADDR)
 148
 149 #define CSC_WAIT_MASK   0x00000007      /* Wait State Selection */
 150 #define CSC_WAIT_SHIFT  0
 151 #define CSC_RO          0x00000008      /* Read-Only */
 152 #define CSC_AM_MASK     0x0000fff0      /* Address Mask (bits 23-12) */
 153 #define CSC_AM_SHIFT    4
 154 #define CSC_BUSW        0x00010000      /* Bus Width Select */
 155 #define CSC_AC_MASK     0xfff00000      /* Address Compare (bits 23-12) */
 156 #define CSC_AC_SHIFT    20
 157
 158 /*
 159  * Chip-Select Option Registers (group D)
 160  */
 161 #define CSD0_ADDR       0xfffff140
 162 #define CSD1_ADDR       0xfffff144
 163 #define CSD2_ADDR       0xfffff148
 164 #define CSD3_ADDR       0xfffff14c
 165
 166 #define CSD0            LONG_REF(CSD0_ADDR)
 167 #define CSD1            LONG_REF(CSD1_ADDR)
 168 #define CSD2            LONG_REF(CSD2_ADDR)
 169 #define CSD3            LONG_REF(CSD3_ADDR)
 170
 171 #define CSD_WAIT_MASK   0x00000007      /* Wait State Selection */
 172 #define CSD_WAIT_SHIFT  0
 173 #define CSD_RO          0x00000008      /* Read-Only */
 174 #define CSD_AM_MASK     0x0000fff0      /* Address Mask (bits 23-12) */
 175 #define CSD_AM_SHIFT    4
 176 #define CSD_BUSW        0x00010000      /* Bus Width Select */
 177 #define CSD_AC_MASK     0xfff00000      /* Address Compare (bits 23-12) */
 178 #define CSD_AC_SHIFT    20
 179
 180 /**********
 181  *
 182  * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control
 183  *
 184  **********/
 185
 186 /*
 187  * PLL Control Register
 188  */
 189 #define PLLCR_ADDR      0xfffff200
 190 #define PLLCR           WORD_REF(PLLCR_ADDR)
 191
 192 #define PLLCR_DISPLL           0x0008   /* Disable PLL */
 193 #define PLLCR_CLKEN            0x0010   /* Clock (CLKO pin) enable */
 194 #define PLLCR_SYSCLK_SEL_MASK  0x0700   /* System Clock Selection */
 195 #define PLLCR_SYSCLK_SEL_SHIFT 8
 196 #define PLLCR_PIXCLK_SEL_MASK  0x3800   /* LCD Clock Selection */
 197 #define PLLCR_PIXCLK_SEL_SHIFT 11
 198
 199 /* 'EZ328-compatible definitions */
 200 #define PLLCR_LCDCLK_SEL_MASK   PLLCR_PIXCLK_SEL_MASK
 201 #define PLLCR_LCDCLK_SEL_SHIFT  PLLCR_PIXCLK_SEL_SHIFT
 202
 203 /*
 204  * PLL Frequency Select Register
 205  */
 206 #define PLLFSR_ADDR     0xfffff202
 207 #define PLLFSR          WORD_REF(PLLFSR_ADDR)
 208
 209 #define PLLFSR_PC_MASK  0x00ff          /* P Count */
 210 #define PLLFSR_PC_SHIFT 0
 211 #define PLLFSR_QC_MASK  0x0f00          /* Q Count */
 212 #define PLLFSR_QC_SHIFT 8
 213 #define PLLFSR_PROT     0x4000          /* Protect P & Q */
 214 #define PLLFSR_CLK32    0x8000          /* Clock 32 (kHz) */
 215
 216 /*
 217  * Power Control Register
 218  */
 219 #define PCTRL_ADDR      0xfffff207
 220 #define PCTRL           BYTE_REF(PCTRL_ADDR)
 221
 222 #define PCTRL_WIDTH_MASK        0x1f    /* CPU Clock bursts width */
 223 #define PCTRL_WIDTH_SHIFT       0
 224 #define PCTRL_STOP              0x40    /* Enter power-save mode immediately */
 225 #define PCTRL_PCEN              0x80    /* Power Control Enable */
 226
 227 /**********
 228  *
 229  * 0xFFFFF3xx -- Interrupt Controller
 230  *
 231  **********/
 232
 233 /*
 234  * Interrupt Vector Register
 235  */
 236 #define IVR_ADDR        0xfffff300
 237 #define IVR             BYTE_REF(IVR_ADDR)
 238
 239 #define IVR_VECTOR_MASK 0xF8
 240
 241 /*
 242  * Interrupt control Register
 243  */
 244 #define ICR_ADRR        0xfffff302
 245 #define ICR             WORD_REF(ICR_ADDR)
 246
 247 #define ICR_ET6         0x0100  /* Edge Trigger Select for IRQ6 */
 248 #define ICR_ET3         0x0200  /* Edge Trigger Select for IRQ3 */
 249 #define ICR_ET2         0x0400  /* Edge Trigger Select for IRQ2 */
 250 #define ICR_ET1         0x0800  /* Edge Trigger Select for IRQ1 */
 251 #define ICR_POL6        0x1000  /* Polarity Control for IRQ6 */
 252 #define ICR_POL3        0x2000  /* Polarity Control for IRQ3 */
 253 #define ICR_POL2        0x4000  /* Polarity Control for IRQ2 */
 254 #define ICR_POL1        0x8000  /* Polarity Control for IRQ1 */
 255
 256 /*
 257  * Interrupt Mask Register
 258  */
 259 #define IMR_ADDR        0xfffff304
 260 #define IMR             LONG_REF(IMR_ADDR)
 261
 262 /*
 263  * Define the names for bit positions first. This is useful for
 264  * request_irq
 265  */
 266 #define SPIM_IRQ_NUM    0       /* SPI Master interrupt */
 267 #define TMR2_IRQ_NUM    1       /* Timer 2 interrupt */
 268 #define UART_IRQ_NUM    2       /* UART interrupt */
 269 #define WDT_IRQ_NUM     3       /* Watchdog Timer interrupt */
 270 #define RTC_IRQ_NUM     4       /* RTC interrupt */
 271 #define KB_IRQ_NUM      6       /* Keyboard Interrupt */
 272 #define PWM_IRQ_NUM     7       /* Pulse-Width Modulator int. */
 273 #define INT0_IRQ_NUM    8       /* External INT0 */
 274 #define INT1_IRQ_NUM    9       /* External INT1 */
 275 #define INT2_IRQ_NUM    10      /* External INT2 */
 276 #define INT3_IRQ_NUM    11      /* External INT3 */
 277 #define INT4_IRQ_NUM    12      /* External INT4 */
 278 #define INT5_IRQ_NUM    13      /* External INT5 */
 279 #define INT6_IRQ_NUM    14      /* External INT6 */
 280 #define INT7_IRQ_NUM    15      /* External INT7 */
 281 #define IRQ1_IRQ_NUM    16      /* IRQ1 */
 282 #define IRQ2_IRQ_NUM    17      /* IRQ2 */
 283 #define IRQ3_IRQ_NUM    18      /* IRQ3 */
 284 #define IRQ6_IRQ_NUM    19      /* IRQ6 */
 285 #define PEN_IRQ_NUM     20      /* Pen Interrupt */
 286 #define SPIS_IRQ_NUM    21      /* SPI Slave Interrupt */
 287 #define TMR1_IRQ_NUM    22      /* Timer 1 interrupt */
 288 #define IRQ7_IRQ_NUM    23      /* IRQ7 */
 289
 290 /* '328-compatible definitions */
 291 #define SPI_IRQ_NUM     SPIM_IRQ_NUM
 292 #define TMR_IRQ_NUM     TMR1_IRQ_NUM
 293
 294 /*
 295  * Here go the bitmasks themselves
 296  */
 297 #define IMR_MSPIM       (1 << SPIM_IRQ_NUM)     /* Mask SPI Master interrupt */
 298 #define IMR_MTMR2       (1 << TMR2_IRQ_NUM)     /* Mask Timer 2 interrupt */
 299 #define IMR_MUART       (1 << UART_IRQ_NUM)     /* Mask UART interrupt */
 300 #define IMR_MWDT        (1 << WDT_IRQ_NUM)      /* Mask Watchdog Timer interrupt */
 301 #define IMR_MRTC        (1 << RTC_IRQ_NUM)      /* Mask RTC interrupt */
 302 #define IMR_MKB         (1 << KB_IRQ_NUM)       /* Mask Keyboard Interrupt */
 303 #define IMR_MPWM        (1 << PWM_IRQ_NUM)      /* Mask Pulse-Width Modulator int. */
 304 #define IMR_MINT0       (1 << INT0_IRQ_NUM)     /* Mask External INT0 */
 305 #define IMR_MINT1       (1 << INT1_IRQ_NUM)     /* Mask External INT1 */
 306 #define IMR_MINT2       (1 << INT2_IRQ_NUM)     /* Mask External INT2 */
 307 #define IMR_MINT3       (1 << INT3_IRQ_NUM)     /* Mask External INT3 */
 308 #define IMR_MINT4       (1 << INT4_IRQ_NUM)     /* Mask External INT4 */
 309 #define IMR_MINT5       (1 << INT5_IRQ_NUM)     /* Mask External INT5 */
 310 #define IMR_MINT6       (1 << INT6_IRQ_NUM)     /* Mask External INT6 */
 311 #define IMR_MINT7       (1 << INT7_IRQ_NUM)     /* Mask External INT7 */
 312 #define IMR_MIRQ1       (1 << IRQ1_IRQ_NUM)     /* Mask IRQ1 */
 313 #define IMR_MIRQ2       (1 << IRQ2_IRQ_NUM)     /* Mask IRQ2 */
 314 #define IMR_MIRQ3       (1 << IRQ3_IRQ_NUM)     /* Mask IRQ3 */
 315 #define IMR_MIRQ6       (1 << IRQ6_IRQ_NUM)     /* Mask IRQ6 */
 316 #define IMR_MPEN        (1 << PEN_IRQ_NUM)      /* Mask Pen Interrupt */
 317 #define IMR_MSPIS       (1 << SPIS_IRQ_NUM)     /* Mask SPI Slave Interrupt */
 318 #define IMR_MTMR1       (1 << TMR1_IRQ_NUM)     /* Mask Timer 1 interrupt */
 319 #define IMR_MIRQ7       (1 << IRQ7_IRQ_NUM)     /* Mask IRQ7 */
 320
 321 /* 'EZ328-compatible definitions */
 322 #define IMR_MSPI        IMR_MSPIM
 323 #define IMR_MTMR        IMR_MTMR1
 324
 325 /*
 326  * Interrupt Wake-Up Enable Register
 327  */
 328 #define IWR_ADDR        0xfffff308
 329 #define IWR             LONG_REF(IWR_ADDR)
 330
 331 #define IWR_SPIM        (1 << SPIM_IRQ_NUM)     /* SPI Master interrupt */
 332 #define IWR_TMR2        (1 << TMR2_IRQ_NUM)     /* Timer 2 interrupt */
 333 #define IWR_UART        (1 << UART_IRQ_NUM)     /* UART interrupt */
 334 #define IWR_WDT         (1 << WDT_IRQ_NUM)      /* Watchdog Timer interrupt */
 335 #define IWR_RTC         (1 << RTC_IRQ_NUM)      /* RTC interrupt */
 336 #define IWR_KB          (1 << KB_IRQ_NUM)       /* Keyboard Interrupt */
 337 #define IWR_PWM         (1 << PWM_IRQ_NUM)      /* Pulse-Width Modulator int. */
 338 #define IWR_INT0        (1 << INT0_IRQ_NUM)     /* External INT0 */
 339 #define IWR_INT1        (1 << INT1_IRQ_NUM)     /* External INT1 */
 340 #define IWR_INT2        (1 << INT2_IRQ_NUM)     /* External INT2 */
 341 #define IWR_INT3        (1 << INT3_IRQ_NUM)     /* External INT3 */
 342 #define IWR_INT4        (1 << INT4_IRQ_NUM)     /* External INT4 */
 343 #define IWR_INT5        (1 << INT5_IRQ_NUM)     /* External INT5 */
 344 #define IWR_INT6        (1 << INT6_IRQ_NUM)     /* External INT6 */
 345 #define IWR_INT7        (1 << INT7_IRQ_NUM)     /* External INT7 */
 346 #define IWR_IRQ1        (1 << IRQ1_IRQ_NUM)     /* IRQ1 */
 347 #define IWR_IRQ2        (1 << IRQ2_IRQ_NUM)     /* IRQ2 */
 348 #define IWR_IRQ3        (1 << IRQ3_IRQ_NUM)     /* IRQ3 */
 349 #define IWR_IRQ6        (1 << IRQ6_IRQ_NUM)     /* IRQ6 */
 350 #define IWR_PEN         (1 << PEN_IRQ_NUM)      /* Pen Interrupt */
 351 #define IWR_SPIS        (1 << SPIS_IRQ_NUM)     /* SPI Slave Interrupt */
 352 #define IWR_TMR1        (1 << TMR1_IRQ_NUM)     /* Timer 1 interrupt */
 353 #define IWR_IRQ7        (1 << IRQ7_IRQ_NUM)     /* IRQ7 */
 354
 355 /*
 356  * Interrupt Status Register
 357  */
 358 #define ISR_ADDR        0xfffff30c
 359 #define ISR             LONG_REF(ISR_ADDR)
 360
 361 #define ISR_SPIM        (1 << SPIM_IRQ_NUM)     /* SPI Master interrupt */
 362 #define ISR_TMR2        (1 << TMR2_IRQ_NUM)     /* Timer 2 interrupt */
 363 #define ISR_UART        (1 << UART_IRQ_NUM)     /* UART interrupt */
 364 #define ISR_WDT         (1 << WDT_IRQ_NUM)      /* Watchdog Timer interrupt */
 365 #define ISR_RTC         (1 << RTC_IRQ_NUM)      /* RTC interrupt */
 366 #define ISR_KB          (1 << KB_IRQ_NUM)       /* Keyboard Interrupt */
 367 #define ISR_PWM         (1 << PWM_IRQ_NUM)      /* Pulse-Width Modulator int. */
 368 #define ISR_INT0        (1 << INT0_IRQ_NUM)     /* External INT0 */
 369 #define ISR_INT1        (1 << INT1_IRQ_NUM)     /* External INT1 */
 370 #define ISR_INT2        (1 << INT2_IRQ_NUM)     /* External INT2 */
 371 #define ISR_INT3        (1 << INT3_IRQ_NUM)     /* External INT3 */
 372 #define ISR_INT4        (1 << INT4_IRQ_NUM)     /* External INT4 */
 373 #define ISR_INT5        (1 << INT5_IRQ_NUM)     /* External INT5 */
 374 #define ISR_INT6        (1 << INT6_IRQ_NUM)     /* External INT6 */
 375 #define ISR_INT7        (1 << INT7_IRQ_NUM)     /* External INT7 */
 376 #define ISR_IRQ1        (1 << IRQ1_IRQ_NUM)     /* IRQ1 */
 377 #define ISR_IRQ2        (1 << IRQ2_IRQ_NUM)     /* IRQ2 */
 378 #define ISR_IRQ3        (1 << IRQ3_IRQ_NUM)     /* IRQ3 */
 379 #define ISR_IRQ6        (1 << IRQ6_IRQ_NUM)     /* IRQ6 */
 380 #define ISR_PEN         (1 << PEN_IRQ_NUM)      /* Pen Interrupt */
 381 #define ISR_SPIS        (1 << SPIS_IRQ_NUM)     /* SPI Slave Interrupt */
 382 #define ISR_TMR1        (1 << TMR1_IRQ_NUM)     /* Timer 1 interrupt */
 383 #define ISR_IRQ7        (1 << IRQ7_IRQ_NUM)     /* IRQ7 */
 384
 385 /* 'EZ328-compatible definitions */
 386 #define ISR_SPI ISR_SPIM
 387 #define ISR_TMR ISR_TMR1
 388
 389 /*
 390  * Interrupt Pending Register
 391  */
 392 #define IPR_ADDR        0xfffff310
 393 #define IPR             LONG_REF(IPR_ADDR)
 394
 395 #define IPR_SPIM        (1 << SPIM_IRQ_NUM)     /* SPI Master interrupt */
 396 #define IPR_TMR2        (1 << TMR2_IRQ_NUM)     /* Timer 2 interrupt */
 397 #define IPR_UART        (1 << UART_IRQ_NUM)     /* UART interrupt */
 398 #define IPR_WDT         (1 << WDT_IRQ_NUM)      /* Watchdog Timer interrupt */
 399 #define IPR_RTC         (1 << RTC_IRQ_NUM)      /* RTC interrupt */
 400 #define IPR_KB          (1 << KB_IRQ_NUM)       /* Keyboard Interrupt */
 401 #define IPR_PWM         (1 << PWM_IRQ_NUM)      /* Pulse-Width Modulator int. */
 402 #define IPR_INT0        (1 << INT0_IRQ_NUM)     /* External INT0 */
 403 #define IPR_INT1        (1 << INT1_IRQ_NUM)     /* External INT1 */
 404 #define IPR_INT2        (1 << INT2_IRQ_NUM)     /* External INT2 */
 405 #define IPR_INT3        (1 << INT3_IRQ_NUM)     /* External INT3 */
 406 #define IPR_INT4        (1 << INT4_IRQ_NUM)     /* External INT4 */
 407 #define IPR_INT5        (1 << INT5_IRQ_NUM)     /* External INT5 */
 408 #define IPR_INT6        (1 << INT6_IRQ_NUM)     /* External INT6 */
 409 #define IPR_INT7        (1 << INT7_IRQ_NUM)     /* External INT7 */
 410 #define IPR_IRQ1        (1 << IRQ1_IRQ_NUM)     /* IRQ1 */
 411 #define IPR_IRQ2        (1 << IRQ2_IRQ_NUM)     /* IRQ2 */
 412 #define IPR_IRQ3        (1 << IRQ3_IRQ_NUM)     /* IRQ3 */
 413 #define IPR_IRQ6        (1 << IRQ6_IRQ_NUM)     /* IRQ6 */
 414 #define IPR_PEN         (1 << PEN_IRQ_NUM)      /* Pen Interrupt */
 415 #define IPR_SPIS        (1 << SPIS_IRQ_NUM)     /* SPI Slave Interrupt */
 416 #define IPR_TMR1        (1 << TMR1_IRQ_NUM)     /* Timer 1 interrupt */
 417 #define IPR_IRQ7        (1 << IRQ7_IRQ_NUM)     /* IRQ7 */
 418
 419 /* 'EZ328-compatible definitions */
 420 #define IPR_SPI IPR_SPIM
 421 #define IPR_TMR IPR_TMR1
 422
 423 /**********
 424  *
 425  * 0xFFFFF4xx -- Parallel Ports
 426  *
 427  **********/
 428
 429 /*
 430  * Port A
 431  */
 432 #define PADIR_ADDR      0xfffff400              /* Port A direction reg */
 433 #define PADATA_ADDR     0xfffff401              /* Port A data register */
 434 #define PASEL_ADDR      0xfffff403              /* Port A Select register */
 435
 436 #define PADIR           BYTE_REF(PADIR_ADDR)
 437 #define PADATA          BYTE_REF(PADATA_ADDR)
 438 #define PASEL           BYTE_REF(PASEL_ADDR)
 439
 440 #define PA(x)           (1 << (x))
 441 #define PA_A(x)         PA((x) - 16)    /* This is specific to PA only! */
 442
 443 #define PA_A16          PA(0)           /* Use A16 as PA(0) */
 444 #define PA_A17          PA(1)           /* Use A17 as PA(1) */
 445 #define PA_A18          PA(2)           /* Use A18 as PA(2) */
 446 #define PA_A19          PA(3)           /* Use A19 as PA(3) */
 447 #define PA_A20          PA(4)           /* Use A20 as PA(4) */
 448 #define PA_A21          PA(5)           /* Use A21 as PA(5) */
 449 #define PA_A22          PA(6)           /* Use A22 as PA(6) */
 450 #define PA_A23          PA(7)           /* Use A23 as PA(7) */
 451
 452 /*
 453  * Port B
 454  */
 455 #define PBDIR_ADDR      0xfffff408              /* Port B direction reg */
 456 #define PBDATA_ADDR     0xfffff409              /* Port B data register */
 457 #define PBSEL_ADDR      0xfffff40b              /* Port B Select Register */
 458
 459 #define PBDIR           BYTE_REF(PBDIR_ADDR)
 460 #define PBDATA          BYTE_REF(PBDATA_ADDR)
 461 #define PBSEL           BYTE_REF(PBSEL_ADDR)
 462
 463 #define PB(x)           (1 << (x))
 464 #define PB_D(x)         PB(x)           /* This is specific to port B only */
 465
 466 #define PB_D0           PB(0)           /* Use D0 as PB(0) */
 467 #define PB_D1           PB(1)           /* Use D1 as PB(1) */
 468 #define PB_D2           PB(2)           /* Use D2 as PB(2) */
 469 #define PB_D3           PB(3)           /* Use D3 as PB(3) */
 470 #define PB_D4           PB(4)           /* Use D4 as PB(4) */
 471 #define PB_D5           PB(5)           /* Use D5 as PB(5) */
 472 #define PB_D6           PB(6)           /* Use D6 as PB(6) */
 473 #define PB_D7           PB(7)           /* Use D7 as PB(7) */
 474
 475 /*
 476  * Port C
 477  */
 478 #define PCDIR_ADDR      0xfffff410              /* Port C direction reg */
 479 #define PCDATA_ADDR     0xfffff411              /* Port C data register */
 480 #define PCSEL_ADDR      0xfffff413              /* Port C Select Register */
 481
 482 #define PCDIR           BYTE_REF(PCDIR_ADDR)
 483 #define PCDATA          BYTE_REF(PCDATA_ADDR)
 484 #define PCSEL           BYTE_REF(PCSEL_ADDR)
 485
 486 #define PC(x)           (1 << (x))
 487
 488 #define PC_WE           PC(6)           /* Use WE    as PC(6) */
 489 #define PC_DTACK        PC(5)           /* Use DTACK as PC(5) */
 490 #define PC_IRQ7         PC(4)           /* Use IRQ7  as PC(4) */
 491 #define PC_LDS          PC(2)           /* Use LDS   as PC(2) */
 492 #define PC_UDS          PC(1)           /* Use UDS   as PC(1) */
 493 #define PC_MOCLK        PC(0)           /* Use MOCLK as PC(0) */
 494
 495 /*
 496  * Port D
 497  */
 498 #define PDDIR_ADDR      0xfffff418              /* Port D direction reg */
 499 #define PDDATA_ADDR     0xfffff419              /* Port D data register */
 500 #define PDPUEN_ADDR     0xfffff41a              /* Port D Pull-Up enable reg */
 501 #define PDPOL_ADDR      0xfffff41c              /* Port D Polarity Register */
 502 #define PDIRQEN_ADDR    0xfffff41d              /* Port D IRQ enable register */
 503 #define PDIQEG_ADDR     0xfffff41f              /* Port D IRQ Edge Register */
 504
 505 #define PDDIR           BYTE_REF(PDDIR_ADDR)
 506 #define PDDATA          BYTE_REF(PDDATA_ADDR)
 507 #define PDPUEN          BYTE_REF(PDPUEN_ADDR)
 508 #define PDPOL           BYTE_REF(PDPOL_ADDR)
 509 #define PDIRQEN         BYTE_REF(PDIRQEN_ADDR)
 510 #define PDIQEG          BYTE_REF(PDIQEG_ADDR)
 511
 512 #define PD(x)           (1 << (x))
 513 #define PD_KB(x)        PD(x)           /* This is specific for Port D only */
 514
 515 #define PD_KB0          PD(0)   /* Use KB0 as PD(0) */
 516 #define PD_KB1          PD(1)   /* Use KB1 as PD(1) */
 517 #define PD_KB2          PD(2)   /* Use KB2 as PD(2) */
 518 #define PD_KB3          PD(3)   /* Use KB3 as PD(3) */
 519 #define PD_KB4          PD(4)   /* Use KB4 as PD(4) */
 520 #define PD_KB5          PD(5)   /* Use KB5 as PD(5) */
 521 #define PD_KB6          PD(6)   /* Use KB6 as PD(6) */
 522 #define PD_KB7          PD(7)   /* Use KB7 as PD(7) */
 523
 524 /*
 525  * Port E
 526  */
 527 #define PEDIR_ADDR      0xfffff420              /* Port E direction reg */
 528 #define PEDATA_ADDR     0xfffff421              /* Port E data register */
 529 #define PEPUEN_ADDR     0xfffff422              /* Port E Pull-Up enable reg */
 530 #define PESEL_ADDR      0xfffff423              /* Port E Select Register */
 531
 532 #define PEDIR           BYTE_REF(PEDIR_ADDR)
 533 #define PEDATA          BYTE_REF(PEDATA_ADDR)
 534 #define PEPUEN          BYTE_REF(PEPUEN_ADDR)
 535 #define PESEL           BYTE_REF(PESEL_ADDR)
 536
 537 #define PE(x)           (1 << (x))
 538
 539 #define PE_CSA1         PE(1)   /* Use CSA1 as PE(1) */
 540 #define PE_CSA2         PE(2)   /* Use CSA2 as PE(2) */
 541 #define PE_CSA3         PE(3)   /* Use CSA3 as PE(3) */
 542 #define PE_CSB0         PE(4)   /* Use CSB0 as PE(4) */
 543 #define PE_CSB1         PE(5)   /* Use CSB1 as PE(5) */
 544 #define PE_CSB2         PE(6)   /* Use CSB2 as PE(6) */
 545 #define PE_CSB3         PE(7)   /* Use CSB3 as PE(7) */
 546
 547 /*
 548  * Port F
 549  */
 550 #define PFDIR_ADDR      0xfffff428              /* Port F direction reg */
 551 #define PFDATA_ADDR     0xfffff429              /* Port F data register */
 552 #define PFPUEN_ADDR     0xfffff42a              /* Port F Pull-Up enable reg */
 553 #define PFSEL_ADDR      0xfffff42b              /* Port F Select Register */
 554
 555 #define PFDIR           BYTE_REF(PFDIR_ADDR)
 556 #define PFDATA          BYTE_REF(PFDATA_ADDR)
 557 #define PFPUEN          BYTE_REF(PFPUEN_ADDR)
 558 #define PFSEL           BYTE_REF(PFSEL_ADDR)
 559
 560 #define PF(x)           (1 << (x))
 561 #define PF_A(x)         PF((x) - 24)    /* This is Port F specific only */
 562
 563 #define PF_A24          PF(0)   /* Use A24 as PF(0) */
 564 #define PF_A25          PF(1)   /* Use A25 as PF(1) */
 565 #define PF_A26          PF(2)   /* Use A26 as PF(2) */
 566 #define PF_A27          PF(3)   /* Use A27 as PF(3) */
 567 #define PF_A28          PF(4)   /* Use A28 as PF(4) */
 568 #define PF_A29          PF(5)   /* Use A29 as PF(5) */
 569 #define PF_A30          PF(6)   /* Use A30 as PF(6) */
 570 #define PF_A31          PF(7)   /* Use A31 as PF(7) */
 571
 572 /*
 573  * Port G
 574  */
 575 #define PGDIR_ADDR      0xfffff430              /* Port G direction reg */
 576 #define PGDATA_ADDR     0xfffff431              /* Port G data register */
 577 #define PGPUEN_ADDR     0xfffff432              /* Port G Pull-Up enable reg */
 578 #define PGSEL_ADDR      0xfffff433              /* Port G Select Register */
 579
 580 #define PGDIR           BYTE_REF(PGDIR_ADDR)
 581 #define PGDATA          BYTE_REF(PGDATA_ADDR)
 582 #define PGPUEN          BYTE_REF(PGPUEN_ADDR)
 583 #define PGSEL           BYTE_REF(PGSEL_ADDR)
 584
 585 #define PG(x)           (1 << (x))
 586
 587 #define PG_UART_TXD     PG(0)   /* Use UART_TXD as PG(0) */
 588 #define PG_UART_RXD     PG(1)   /* Use UART_RXD as PG(1) */
 589 #define PG_PWMOUT       PG(2)   /* Use PWMOUT   as PG(2) */
 590 #define PG_TOUT2        PG(3)   /* Use TOUT2    as PG(3) */
 591 #define PG_TIN2         PG(4)   /* Use TIN2     as PG(4) */
 592 #define PG_TOUT1        PG(5)   /* Use TOUT1    as PG(5) */
 593 #define PG_TIN1         PG(6)   /* Use TIN1     as PG(6) */
 594 #define PG_RTCOUT       PG(7)   /* Use RTCOUT   as PG(7) */
 595
 596 /*
 597  * Port J
 598  */
 599 #define PJDIR_ADDR      0xfffff438              /* Port J direction reg */
 600 #define PJDATA_ADDR     0xfffff439              /* Port J data register */
 601 #define PJSEL_ADDR      0xfffff43b              /* Port J Select Register */
 602
 603 #define PJDIR           BYTE_REF(PJDIR_ADDR)
 604 #define PJDATA          BYTE_REF(PJDATA_ADDR)
 605 #define PJSEL           BYTE_REF(PJSEL_ADDR)
 606
 607 #define PJ(x)           (1 << (x))
 608
 609 #define PJ_CSD3         PJ(7)   /* Use CSD3 as PJ(7) */
 610
 611 /*
 612  * Port K
 613  */
 614 #define PKDIR_ADDR      0xfffff440              /* Port K direction reg */
 615 #define PKDATA_ADDR     0xfffff441              /* Port K data register */
 616 #define PKPUEN_ADDR     0xfffff442              /* Port K Pull-Up enable reg */
 617 #define PKSEL_ADDR      0xfffff443              /* Port K Select Register */
 618
 619 #define PKDIR           BYTE_REF(PKDIR_ADDR)
 620 #define PKDATA          BYTE_REF(PKDATA_ADDR)
 621 #define PKPUEN          BYTE_REF(PKPUEN_ADDR)
 622 #define PKSEL           BYTE_REF(PKSEL_ADDR)
 623
 624 #define PK(x)           (1 << (x))
 625
 626 /*
 627  * Port M
 628  */
 629 #define PMDIR_ADDR      0xfffff438              /* Port M direction reg */
 630 #define PMDATA_ADDR     0xfffff439              /* Port M data register */
 631 #define PMPUEN_ADDR     0xfffff43a              /* Port M Pull-Up enable reg */
 632 #define PMSEL_ADDR      0xfffff43b              /* Port M Select Register */
 633
 634 #define PMDIR           BYTE_REF(PMDIR_ADDR)
 635 #define PMDATA          BYTE_REF(PMDATA_ADDR)
 636 #define PMPUEN          BYTE_REF(PMPUEN_ADDR)
 637 #define PMSEL           BYTE_REF(PMSEL_ADDR)
 638
 639 #define PM(x)           (1 << (x))
 640
 641 /**********
 642  *
 643  * 0xFFFFF5xx -- Pulse-Width Modulator (PWM)
 644  *
 645  **********/
 646
 647 /*
 648  * PWM Control Register
 649  */
 650 #define PWMC_ADDR       0xfffff500
 651 #define PWMC            WORD_REF(PWMC_ADDR)
 652
 653 #define PWMC_CLKSEL_MASK        0x0007  /* Clock Selection */
 654 #define PWMC_CLKSEL_SHIFT       0
 655 #define PWMC_PWMEN              0x0010  /* Enable PWM */
 656 #define PMNC_POL                0x0020  /* PWM Output Bit Polarity */
 657 #define PWMC_PIN                0x0080  /* Current PWM output pin status */
 658 #define PWMC_LOAD               0x0100  /* Force a new period */
 659 #define PWMC_IRQEN              0x4000  /* Interrupt Request Enable */
 660 #define PWMC_CLKSRC             0x8000  /* Clock Source Select */
 661
 662 /* 'EZ328-compatible definitions */
 663 #define PWMC_EN PWMC_PWMEN
 664
 665 /*
 666  * PWM Period Register
 667  */
 668 #define PWMP_ADDR       0xfffff502
 669 #define PWMP            WORD_REF(PWMP_ADDR)
 670
 671 /*
 672  * PWM Width Register
 673  */
 674 #define PWMW_ADDR       0xfffff504
 675 #define PWMW            WORD_REF(PWMW_ADDR)
 676
 677 /*
 678  * PWM Counter Register
 679  */
 680 #define PWMCNT_ADDR     0xfffff506
 681 #define PWMCNT          WORD_REF(PWMCNT_ADDR)
 682
 683 /**********
 684  *
 685  * 0xFFFFF6xx -- General-Purpose Timers
 686  *
 687  **********/
 688
 689 /*
 690  * Timer Unit 1 and 2 Control Registers
 691  */
 692 #define TCTL1_ADDR      0xfffff600
 693 #define TCTL1           WORD_REF(TCTL1_ADDR)
 694 #define TCTL2_ADDR      0xfffff60c
 695 #define TCTL2           WORD_REF(TCTL2_ADDR)
 696
 697 #define TCTL_TEN                0x0001  /* Timer Enable  */
 698 #define TCTL_CLKSOURCE_MASK     0x000e  /* Clock Source: */
 699 #define   TCTL_CLKSOURCE_STOP      0x0000       /* Stop count (disabled)    */
 700 #define   TCTL_CLKSOURCE_SYSCLK    0x0002       /* SYSCLK to prescaler      */
 701 #define   TCTL_CLKSOURCE_SYSCLK_16 0x0004       /* SYSCLK/16 to prescaler   */
 702 #define   TCTL_CLKSOURCE_TIN       0x0006       /* TIN to prescaler         */
 703 #define   TCTL_CLKSOURCE_32KHZ     0x0008       /* 32kHz clock to prescaler */
 704 #define TCTL_IRQEN              0x0010  /* IRQ Enable    */
 705 #define TCTL_OM                 0x0020  /* Output Mode   */
 706 #define TCTL_CAP_MASK           0x00c0  /* Capture Edge: */
 707 #define   TCTL_CAP_RE           0x0040          /* Capture on rizing edge   */
 708 #define   TCTL_CAP_FE           0x0080          /* Capture on falling edge  */
 709 #define TCTL_FRR                0x0010  /* Free-Run Mode */
 710
 711 /* 'EZ328-compatible definitions */
 712 #define TCTL_ADDR       TCTL1_ADDR
 713 #define TCTL            TCTL1
 714
 715 /*
 716  * Timer Unit 1 and 2 Prescaler Registers
 717  */
 718 #define TPRER1_ADDR     0xfffff602
 719 #define TPRER1          WORD_REF(TPRER1_ADDR)
 720 #define TPRER2_ADDR     0xfffff60e
 721 #define TPRER2          WORD_REF(TPRER2_ADDR)
 722
 723 /* 'EZ328-compatible definitions */
 724 #define TPRER_ADDR      TPRER1_ADDR
 725 #define TPRER           TPRER1
 726
 727 /*
 728  * Timer Unit 1 and 2 Compare Registers
 729  */
 730 #define TCMP1_ADDR      0xfffff604
 731 #define TCMP1           WORD_REF(TCMP1_ADDR)
 732 #define TCMP2_ADDR      0xfffff610
 733 #define TCMP2           WORD_REF(TCMP2_ADDR)
 734
 735 /* 'EZ328-compatible definitions */
 736 #define TCMP_ADDR       TCMP1_ADDR
 737 #define TCMP            TCMP1
 738
 739 /*
 740  * Timer Unit 1 and 2 Capture Registers
 741  */
 742 #define TCR1_ADDR       0xfffff606
 743 #define TCR1            WORD_REF(TCR1_ADDR)
 744 #define TCR2_ADDR       0xfffff612
 745 #define TCR2            WORD_REF(TCR2_ADDR)
 746
 747 /* 'EZ328-compatible definitions */
 748 #define TCR_ADDR        TCR1_ADDR
 749 #define TCR             TCR1
 750
 751 /*
 752  * Timer Unit 1 and 2 Counter Registers
 753  */
 754 #define TCN1_ADDR       0xfffff608
 755 #define TCN1            WORD_REF(TCN1_ADDR)
 756 #define TCN2_ADDR       0xfffff614
 757 #define TCN2            WORD_REF(TCN2_ADDR)
 758
 759 /* 'EZ328-compatible definitions */
 760 #define TCN_ADDR        TCN1_ADDR
 761 #define TCN             TCN1
 762
 763 /*
 764  * Timer Unit 1 and 2 Status Registers
 765  */
 766 #define TSTAT1_ADDR     0xfffff60a
 767 #define TSTAT1          WORD_REF(TSTAT1_ADDR)
 768 #define TSTAT2_ADDR     0xfffff616
 769 #define TSTAT2          WORD_REF(TSTAT2_ADDR)
 770
 771 #define TSTAT_COMP      0x0001          /* Compare Event occurred */
 772 #define TSTAT_CAPT      0x0001          /* Capture Event occurred */
 773
 774 /* 'EZ328-compatible definitions */
 775 #define TSTAT_ADDR      TSTAT1_ADDR
 776 #define TSTAT           TSTAT1
 777
 778 /*
 779  * Watchdog Compare Register
 780  */
 781 #define WRR_ADDR        0xfffff61a
 782 #define WRR             WORD_REF(WRR_ADDR)
 783
 784 /*
 785  * Watchdog Counter Register
 786  */
 787 #define WCN_ADDR        0xfffff61c
 788 #define WCN             WORD_REF(WCN_ADDR)
 789
 790 /*
 791  * Watchdog Control and Status Register
 792  */
 793 #define WCSR_ADDR       0xfffff618
 794 #define WCSR            WORD_REF(WCSR_ADDR)
 795
 796 #define WCSR_WDEN       0x0001  /* Watchdog Enable */
 797 #define WCSR_FI         0x0002  /* Forced Interrupt (instead of SW reset)*/
 798 #define WCSR_WRST       0x0004  /* Watchdog Reset */
 799
 800 /**********
 801  *
 802  * 0xFFFFF7xx -- Serial Peripheral Interface Slave (SPIS)
 803  *
 804  **********/
 805
 806 /*
 807  * SPI Slave Register
 808  */
 809 #define SPISR_ADDR      0xfffff700
 810 #define SPISR           WORD_REF(SPISR_ADDR)
 811
 812 #define SPISR_DATA_ADDR 0xfffff701
 813 #define SPISR_DATA      BYTE_REF(SPISR_DATA_ADDR)
 814
 815 #define SPISR_DATA_MASK  0x00ff /* Shifted data from the external device */
 816 #define SPISR_DATA_SHIFT 0
 817 #define SPISR_SPISEN     0x0100 /* SPIS module enable */
 818 #define SPISR_POL        0x0200 /* SPSCLK polarity control */
 819 #define SPISR_PHA        0x0400 /* Phase relationship between SPSCLK & SPSRxD */
 820 #define SPISR_OVWR       0x0800 /* Data buffer has been overwritten */
 821 #define SPISR_DATARDY    0x1000 /* Data ready */
 822 #define SPISR_ENPOL      0x2000 /* Enable Polarity */
 823 #define SPISR_IRQEN      0x4000 /* SPIS IRQ Enable */
 824 #define SPISR_SPISIRQ    0x8000 /* SPIS IRQ posted */
 825
 826 /**********
 827  *
 828  * 0xFFFFF8xx -- Serial Peripheral Interface Master (SPIM)
 829  *
 830  **********/
 831
 832 /*
 833  * SPIM Data Register
 834  */
 835 #define SPIMDATA_ADDR   0xfffff800
 836 #define SPIMDATA        WORD_REF(SPIMDATA_ADDR)
 837
 838 /*
 839  * SPIM Control/Status Register
 840  */
 841 #define SPIMCONT_ADDR   0xfffff802
 842 #define SPIMCONT        WORD_REF(SPIMCONT_ADDR)
 843
 844 #define SPIMCONT_BIT_COUNT_MASK  0x000f /* Transfer Length in Bytes */
 845 #define SPIMCONT_BIT_COUNT_SHIFT 0
 846 #define SPIMCONT_POL             0x0010 /* SPMCLK Signel Polarity */
 847 #define SPIMCONT_PHA             0x0020 /* Clock/Data phase relationship */
 848 #define SPIMCONT_IRQEN           0x0040 /* IRQ Enable */
 849 #define SPIMCONT_SPIMIRQ         0x0080 /* Interrupt Request */
 850 #define SPIMCONT_XCH             0x0100 /* Exchange */
 851 #define SPIMCONT_RSPIMEN         0x0200 /* Enable SPIM */
 852 #define SPIMCONT_DATA_RATE_MASK  0xe000 /* SPIM Data Rate */
 853 #define SPIMCONT_DATA_RATE_SHIFT 13
 854
 855 /* 'EZ328-compatible definitions */
 856 #define SPIMCONT_IRQ    SPIMCONT_SPIMIRQ
 857 #define SPIMCONT_ENABLE SPIMCONT_SPIMEN
 858 /**********
 859  *
 860  * 0xFFFFF9xx -- UART
 861  *
 862  **********/
 863
 864 /*
 865  * UART Status/Control Register
 866  */
 867 #define USTCNT_ADDR     0xfffff900
 868 #define USTCNT          WORD_REF(USTCNT_ADDR)
 869
 870 #define USTCNT_TXAVAILEN        0x0001  /* Transmitter Available Int Enable */
 871 #define USTCNT_TXHALFEN         0x0002  /* Transmitter Half Empty Int Enable */
 872 #define USTCNT_TXEMPTYEN        0x0004  /* Transmitter Empty Int Enable */
 873 #define USTCNT_RXREADYEN        0x0008  /* Receiver Ready Interrupt Enable */
 874 #define USTCNT_RXHALFEN         0x0010  /* Receiver Half-Full Int Enable */
 875 #define USTCNT_RXFULLEN         0x0020  /* Receiver Full Interrupt Enable */
 876 #define USTCNT_CTSDELTAEN       0x0040  /* CTS Delta Interrupt Enable */
 877 #define USTCNT_GPIODELTAEN      0x0080  /* Old Data Interrupt Enable */
 878 #define USTCNT_8_7              0x0100  /* Eight or seven-bit transmission */
 879 #define USTCNT_STOP             0x0200  /* Stop bit transmission */
 880 #define USTCNT_ODD_EVEN         0x0400  /* Odd Parity */
 881 #define USTCNT_PARITYEN         0x0800  /* Parity Enable */
 882 #define USTCNT_CLKMODE          0x1000  /* Clock Mode Select */
 883 #define USTCNT_TXEN             0x2000  /* Transmitter Enable */
 884 #define USTCNT_RXEN             0x4000  /* Receiver Enable */
 885 #define USTCNT_UARTEN           0x8000  /* UART Enable */
 886
 887 /* 'EZ328-compatible definitions */
 888 #define USTCNT_TXAE     USTCNT_TXAVAILEN
 889 #define USTCNT_TXHE     USTCNT_TXHALFEN
 890 #define USTCNT_TXEE     USTCNT_TXEMPTYEN
 891 #define USTCNT_RXRE     USTCNT_RXREADYEN
 892 #define USTCNT_RXHE     USTCNT_RXHALFEN
 893 #define USTCNT_RXFE     USTCNT_RXFULLEN
 894 #define USTCNT_CTSD     USTCNT_CTSDELTAEN
 895 #define USTCNT_ODD      USTCNT_ODD_EVEN
 896 #define USTCNT_PEN      USTCNT_PARITYEN
 897 #define USTCNT_CLKM     USTCNT_CLKMODE
 898 #define USTCNT_UEN      USTCNT_UARTEN
 899
 900 /*
 901  * UART Baud Control Register
 902  */
 903 #define UBAUD_ADDR      0xfffff902
 904 #define UBAUD           WORD_REF(UBAUD_ADDR)
 905
 906 #define UBAUD_PRESCALER_MASK    0x003f  /* Actual divisor is 65 - PRESCALER */
 907 #define UBAUD_PRESCALER_SHIFT   0
 908 #define UBAUD_DIVIDE_MASK       0x0700  /* Baud Rate freq. divisor */
 909 #define UBAUD_DIVIDE_SHIFT      8
 910 #define UBAUD_BAUD_SRC          0x0800  /* Baud Rate Source */
 911 #define UBAUD_GPIOSRC           0x1000  /* GPIO source */
 912 #define UBAUD_GPIODIR           0x2000  /* GPIO Direction */
 913 #define UBAUD_GPIO              0x4000  /* Current GPIO pin status */
 914 #define UBAUD_GPIODELTA         0x8000  /* GPIO pin value changed */
 915
 916 /*
 917  * UART Receiver Register
 918  */
 919 #define URX_ADDR        0xfffff904
 920 #define URX             WORD_REF(URX_ADDR)
 921
 922 #define URX_RXDATA_ADDR 0xfffff905
 923 #define URX_RXDATA      BYTE_REF(URX_RXDATA_ADDR)
 924
 925 #define URX_RXDATA_MASK  0x00ff /* Received data */
 926 #define URX_RXDATA_SHIFT 0
 927 #define URX_PARITY_ERROR 0x0100 /* Parity Error */
 928 #define URX_BREAK        0x0200 /* Break Detected */
 929 #define URX_FRAME_ERROR  0x0400 /* Framing Error */
 930 #define URX_OVRUN        0x0800 /* Serial Overrun */
 931 #define URX_DATA_READY   0x2000 /* Data Ready (FIFO not empty) */
 932 #define URX_FIFO_HALF    0x4000 /* FIFO is Half-Full */
 933 #define URX_FIFO_FULL    0x8000 /* FIFO is Full */
 934
 935 /*
 936  * UART Transmitter Register
 937  */
 938 #define UTX_ADDR        0xfffff906
 939 #define UTX             WORD_REF(UTX_ADDR)
 940
 941 #define UTX_TXDATA_ADDR 0xfffff907
 942 #define UTX_TXDATA      BYTE_REF(UTX_TXDATA_ADDR)
 943
 944 #define UTX_TXDATA_MASK  0x00ff /* Data to be transmitted */
 945 #define UTX_TXDATA_SHIFT 0
 946 #define UTX_CTS_DELTA    0x0100 /* CTS changed */
 947 #define UTX_CTS_STATUS   0x0200 /* CTS State */
 948 #define UTX_IGNORE_CTS   0x0800 /* Ignore CTS */
 949 #define UTX_SEND_BREAK   0x1000 /* Send a BREAK */
 950 #define UTX_TX_AVAIL     0x2000 /* Transmit FIFO has a slot available */
 951 #define UTX_FIFO_HALF    0x4000 /* Transmit FIFO is half empty */
 952 #define UTX_FIFO_EMPTY   0x8000 /* Transmit FIFO is empty */
 953
 954 /* 'EZ328-compatible definitions */
 955 #define UTX_CTS_STAT    UTX_CTS_STATUS
 956 #define UTX_NOCTS       UTX_IGNORE_CTS
 957
 958 /*
 959  * UART Miscellaneous Register
 960  */
 961 #define UMISC_ADDR      0xfffff908
 962 #define UMISC           WORD_REF(UMISC_ADDR)
 963
 964 #define UMISC_TX_POL     0x0004 /* Transmit Polarity */
 965 #define UMISC_RX_POL     0x0008 /* Receive Polarity */
 966 #define UMISC_IRDA_LOOP  0x0010 /* IrDA Loopback Enable */
 967 #define UMISC_IRDA_EN    0x0020 /* Infra-Red Enable */
 968 #define UMISC_RTS        0x0040 /* Set RTS status */
 969 #define UMISC_RTSCONT    0x0080 /* Choose RTS control */
 970 #define UMISC_LOOP       0x1000 /* Serial Loopback Enable */
 971 #define UMISC_FORCE_PERR 0x2000 /* Force Parity Error */
 972 #define UMISC_CLKSRC     0x4000 /* Clock Source */
 973
 974
 975 /* generalization of uart control registers to support multiple ports: */
 976 typedef volatile struct {
 977   volatile unsigned short int ustcnt;
 978   volatile unsigned short int ubaud;
 979   union {
 980     volatile unsigned short int w;
 981     struct {
 982       volatile unsigned char status;
 983       volatile unsigned char rxdata;
 984     } b;
 985   } urx;
 986   union {
 987     volatile unsigned short int w;
 988     struct {
 989       volatile unsigned char status;
 990       volatile unsigned char txdata;
 991     } b;
 992   } utx;
 993   volatile unsigned short int umisc;
 994   volatile unsigned short int pad1;
 995   volatile unsigned short int pad2;
 996   volatile unsigned short int pad3;
 997 } __packed m68328_uart;
 998
 999
1000 /**********
1001  *
1002  * 0xFFFFFAxx -- LCD Controller
1003  *
1004  **********/
1005
1006 /*
1007  * LCD Screen Starting Address Register
1008  */
1009 #define LSSA_ADDR       0xfffffa00
1010 #define LSSA            LONG_REF(LSSA_ADDR)
1011
1012 #define LSSA_SSA_MASK   0xfffffffe      /* Bit 0 is reserved */
1013
1014 /*
1015  * LCD Virtual Page Width Register
1016  */
1017 #define LVPW_ADDR       0xfffffa05
1018 #define LVPW            BYTE_REF(LVPW_ADDR)
1019
1020 /*
1021  * LCD Screen Width Register (not compatible with 'EZ328 !!!)
1022  */
1023 #define LXMAX_ADDR      0xfffffa08
1024 #define LXMAX           WORD_REF(LXMAX_ADDR)
1025
1026 #define LXMAX_XM_MASK   0x02ff          /* Bits 0-3 are reserved */
1027
1028 /*
1029  * LCD Screen Height Register
1030  */
1031 #define LYMAX_ADDR      0xfffffa0a
1032 #define LYMAX           WORD_REF(LYMAX_ADDR)
1033
1034 #define LYMAX_YM_MASK   0x02ff          /* Bits 10-15 are reserved */
1035
1036 /*
1037  * LCD Cursor X Position Register
1038  */
1039 #define LCXP_ADDR       0xfffffa18
1040 #define LCXP            WORD_REF(LCXP_ADDR)
1041
1042 #define LCXP_CC_MASK    0xc000          /* Cursor Control */
1043 #define   LCXP_CC_TRAMSPARENT   0x0000
1044 #define   LCXP_CC_BLACK         0x4000
1045 #define   LCXP_CC_REVERSED      0x8000
1046 #define   LCXP_CC_WHITE         0xc000
1047 #define LCXP_CXP_MASK   0x02ff          /* Cursor X position */
1048
1049 /*
1050  * LCD Cursor Y Position Register
1051  */
1052 #define LCYP_ADDR       0xfffffa1a
1053 #define LCYP            WORD_REF(LCYP_ADDR)
1054
1055 #define LCYP_CYP_MASK   0x01ff          /* Cursor Y Position */
1056
1057 /*
1058  * LCD Cursor Width and Heigth Register
1059  */
1060 #define LCWCH_ADDR      0xfffffa1c
1061 #define LCWCH           WORD_REF(LCWCH_ADDR)
1062
1063 #define LCWCH_CH_MASK   0x001f          /* Cursor Height */
1064 #define LCWCH_CH_SHIFT  0
1065 #define LCWCH_CW_MASK   0x1f00          /* Cursor Width */
1066 #define LCWCH_CW_SHIFT  8
1067
1068 /*
1069  * LCD Blink Control Register
1070  */
1071 #define LBLKC_ADDR      0xfffffa1f
1072 #define LBLKC           BYTE_REF(LBLKC_ADDR)
1073
1074 #define LBLKC_BD_MASK   0x7f    /* Blink Divisor */
1075 #define LBLKC_BD_SHIFT  0
1076 #define LBLKC_BKEN      0x80    /* Blink Enabled */
1077
1078 /*
1079  * LCD Panel Interface Configuration Register
1080  */
1081 #define LPICF_ADDR      0xfffffa20
1082 #define LPICF           BYTE_REF(LPICF_ADDR)
1083
1084 #define LPICF_GS_MASK    0x01    /* Gray-Scale Mode */
1085 #define   LPICF_GS_BW      0x00
1086 #define   LPICF_GS_GRAY_4  0x01
1087 #define LPICF_PBSIZ_MASK 0x06   /* Panel Bus Width */
1088 #define   LPICF_PBSIZ_1    0x00
1089 #define   LPICF_PBSIZ_2    0x02
1090 #define   LPICF_PBSIZ_4    0x04
1091
1092 /*
1093  * LCD Polarity Configuration Register
1094  */
1095 #define LPOLCF_ADDR     0xfffffa21
1096 #define LPOLCF          BYTE_REF(LPOLCF_ADDR)
1097
1098 #define LPOLCF_PIXPOL   0x01    /* Pixel Polarity */
1099 #define LPOLCF_LPPOL    0x02    /* Line Pulse Polarity */
1100 #define LPOLCF_FLMPOL   0x04    /* Frame Marker Polarity */
1101 #define LPOLCF_LCKPOL   0x08    /* LCD Shift Lock Polarity */
1102
1103 /*
1104  * LACD (LCD Alternate Crystal Direction) Rate Control Register
1105  */
1106 #define LACDRC_ADDR     0xfffffa23
1107 #define LACDRC          BYTE_REF(LACDRC_ADDR)
1108
1109 #define LACDRC_ACD_MASK  0x0f   /* Alternate Crystal Direction Control */
1110 #define LACDRC_ACD_SHIFT 0
1111
1112 /*
1113  * LCD Pixel Clock Divider Register
1114  */
1115 #define LPXCD_ADDR      0xfffffa25
1116 #define LPXCD           BYTE_REF(LPXCD_ADDR)
1117
1118 #define LPXCD_PCD_MASK  0x3f    /* Pixel Clock Divider */
1119 #define LPXCD_PCD_SHIFT 0
1120
1121 /*
1122  * LCD Clocking Control Register
1123  */
1124 #define LCKCON_ADDR     0xfffffa27
1125 #define LCKCON          BYTE_REF(LCKCON_ADDR)
1126
1127 #define LCKCON_PCDS      0x01   /* Pixel Clock Divider Source Select */
1128 #define LCKCON_DWIDTH    0x02   /* Display Memory Width  */
1129 #define LCKCON_DWS_MASK  0x3c   /* Display Wait-State */
1130 #define LCKCON_DWS_SHIFT 2
1131 #define LCKCON_DMA16     0x40   /* DMA burst length */
1132 #define LCKCON_LCDON     0x80   /* Enable LCD Controller */
1133
1134 /* 'EZ328-compatible definitions */
1135 #define LCKCON_DW_MASK  LCKCON_DWS_MASK
1136 #define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT
1137
1138 /*
1139  * LCD Last Buffer Address Register
1140  */
1141 #define LLBAR_ADDR      0xfffffa29
1142 #define LLBAR           BYTE_REF(LLBAR_ADDR)
1143
1144 #define LLBAR_LBAR_MASK  0x7f   /* Number of memory words to fill 1 line */
1145 #define LLBAR_LBAR_SHIFT 0
1146
1147 /*
1148  * LCD Octet Terminal Count Register
1149  */
1150 #define LOTCR_ADDR      0xfffffa2b
1151 #define LOTCR           BYTE_REF(LOTCR_ADDR)
1152
1153 /*
1154  * LCD Panning Offset Register
1155  */
1156 #define LPOSR_ADDR      0xfffffa2d
1157 #define LPOSR           BYTE_REF(LPOSR_ADDR)
1158
1159 #define LPOSR_BOS       0x08    /* Byte offset (for B/W mode only */
1160 #define LPOSR_POS_MASK  0x07    /* Pixel Offset Code */
1161 #define LPOSR_POS_SHIFT 0
1162
1163 /*
1164  * LCD Frame Rate Control Modulation Register
1165  */
1166 #define LFRCM_ADDR      0xfffffa31
1167 #define LFRCM           BYTE_REF(LFRCM_ADDR)
1168
1169 #define LFRCM_YMOD_MASK  0x0f   /* Vertical Modulation */
1170 #define LFRCM_YMOD_SHIFT 0
1171 #define LFRCM_XMOD_MASK  0xf0   /* Horizontal Modulation */
1172 #define LFRCM_XMOD_SHIFT 4
1173
1174 /*
1175  * LCD Gray Palette Mapping Register
1176  */
1177 #define LGPMR_ADDR      0xfffffa32
1178 #define LGPMR           WORD_REF(LGPMR_ADDR)
1179
1180 #define LGPMR_GLEVEL3_MASK      0x000f
1181 #define LGPMR_GLEVEL3_SHIFT     0
1182 #define LGPMR_GLEVEL2_MASK      0x00f0
1183 #define LGPMR_GLEVEL2_SHIFT     4
1184 #define LGPMR_GLEVEL0_MASK      0x0f00
1185 #define LGPMR_GLEVEL0_SHIFT     8
1186 #define LGPMR_GLEVEL1_MASK      0xf000
1187 #define LGPMR_GLEVEL1_SHIFT     12
1188
1189 /**********
1190  *
1191  * 0xFFFFFBxx -- Real-Time Clock (RTC)
1192  *
1193  **********/
1194
1195 /*
1196  * RTC Hours Minutes and Seconds Register
1197  */
1198 #define RTCTIME_ADDR    0xfffffb00
1199 #define RTCTIME         LONG_REF(RTCTIME_ADDR)
1200
1201 #define RTCTIME_SECONDS_MASK    0x0000003f      /* Seconds */
1202 #define RTCTIME_SECONDS_SHIFT   0
1203 #define RTCTIME_MINUTES_MASK    0x003f0000      /* Minutes */
1204 #define RTCTIME_MINUTES_SHIFT   16
1205 #define RTCTIME_HOURS_MASK      0x1f000000      /* Hours */
1206 #define RTCTIME_HOURS_SHIFT     24
1207
1208 /*
1209  *  RTC Alarm Register
1210  */
1211 #define RTCALRM_ADDR    0xfffffb04
1212 #define RTCALRM         LONG_REF(RTCALRM_ADDR)
1213
1214 #define RTCALRM_SECONDS_MASK    0x0000003f      /* Seconds */
1215 #define RTCALRM_SECONDS_SHIFT   0
1216 #define RTCALRM_MINUTES_MASK    0x003f0000      /* Minutes */
1217 #define RTCALRM_MINUTES_SHIFT   16
1218 #define RTCALRM_HOURS_MASK      0x1f000000      /* Hours */
1219 #define RTCALRM_HOURS_SHIFT     24
1220
1221 /*
1222  * RTC Control Register
1223  */
1224 #define RTCCTL_ADDR     0xfffffb0c
1225 #define RTCCTL          WORD_REF(RTCCTL_ADDR)
1226
1227 #define RTCCTL_384      0x0020  /* Crystal Selection */
1228 #define RTCCTL_ENABLE   0x0080  /* RTC Enable */
1229
1230 /* 'EZ328-compatible definitions */
1231 #define RTCCTL_XTL      RTCCTL_384
1232 #define RTCCTL_EN       RTCCTL_ENABLE
1233
1234 /*
1235  * RTC Interrupt Status Register
1236  */
1237 #define RTCISR_ADDR     0xfffffb0e
1238 #define RTCISR          WORD_REF(RTCISR_ADDR)
1239
1240 #define RTCISR_SW       0x0001  /* Stopwatch timed out */
1241 #define RTCISR_MIN      0x0002  /* 1-minute interrupt has occurred */
1242 #define RTCISR_ALM      0x0004  /* Alarm interrupt has occurred */
1243 #define RTCISR_DAY      0x0008  /* 24-hour rollover interrupt has occurred */
1244 #define RTCISR_1HZ      0x0010  /* 1Hz interrupt has occurred */
1245
1246 /*
1247  * RTC Interrupt Enable Register
1248  */
1249 #define RTCIENR_ADDR    0xfffffb10
1250 #define RTCIENR         WORD_REF(RTCIENR_ADDR)
1251
1252 #define RTCIENR_SW      0x0001  /* Stopwatch interrupt enable */
1253 #define RTCIENR_MIN     0x0002  /* 1-minute interrupt enable */
1254 #define RTCIENR_ALM     0x0004  /* Alarm interrupt enable */
1255 #define RTCIENR_DAY     0x0008  /* 24-hour rollover interrupt enable */
1256 #define RTCIENR_1HZ     0x0010  /* 1Hz interrupt enable */
1257
1258 /*
1259  * Stopwatch Minutes Register
1260  */
1261 #define STPWCH_ADDR     0xfffffb12
1262 #define STPWCH          WORD_REF(STPWCH)
1263
1264 #define STPWCH_CNT_MASK  0x00ff /* Stopwatch countdown value */
1265 #define SPTWCH_CNT_SHIFT 0
1266
1267 #endif /* _MC68328_H_ */