drivers/net/ethernet/dec/tulip/de4x5.h

   1 /*
   2     Copyright 1994 Digital Equipment Corporation.
   3
   4     This software may be used and distributed according to  the terms of the
   5     GNU General Public License, incorporated herein by reference.
   6
   7     The author may    be  reached as davies@wanton.lkg.dec.com  or   Digital
   8     Equipment Corporation, 550 King Street, Littleton MA 01460.
   9
  10     =========================================================================
  11 */
  12
  13 /*
  14 ** DC21040 CSR<1..15> Register Address Map
  15 */
  16 #define DE4X5_BMR    iobase+(0x000 << lp->bus)  /* Bus Mode Register */
  17 #define DE4X5_TPD    iobase+(0x008 << lp->bus)  /* Transmit Poll Demand Reg */
  18 #define DE4X5_RPD    iobase+(0x010 << lp->bus)  /* Receive Poll Demand Reg */
  19 #define DE4X5_RRBA   iobase+(0x018 << lp->bus)  /* RX Ring Base Address Reg */
  20 #define DE4X5_TRBA   iobase+(0x020 << lp->bus)  /* TX Ring Base Address Reg */
  21 #define DE4X5_STS    iobase+(0x028 << lp->bus)  /* Status Register */
  22 #define DE4X5_OMR    iobase+(0x030 << lp->bus)  /* Operation Mode Register */
  23 #define DE4X5_IMR    iobase+(0x038 << lp->bus)  /* Interrupt Mask Register */
  24 #define DE4X5_MFC    iobase+(0x040 << lp->bus)  /* Missed Frame Counter */
  25 #define DE4X5_APROM  iobase+(0x048 << lp->bus)  /* Ethernet Address PROM */
  26 #define DE4X5_BROM   iobase+(0x048 << lp->bus)  /* Boot ROM Register */
  27 #define DE4X5_SROM   iobase+(0x048 << lp->bus)  /* Serial ROM Register */
  28 #define DE4X5_MII    iobase+(0x048 << lp->bus)  /* MII Interface Register */
  29 #define DE4X5_DDR    iobase+(0x050 << lp->bus)  /* Data Diagnostic Register */
  30 #define DE4X5_FDR    iobase+(0x058 << lp->bus)  /* Full Duplex Register */
  31 #define DE4X5_GPT    iobase+(0x058 << lp->bus)  /* General Purpose Timer Reg.*/
  32 #define DE4X5_GEP    iobase+(0x060 << lp->bus)  /* General Purpose Register */
  33 #define DE4X5_SISR   iobase+(0x060 << lp->bus)  /* SIA Status Register */
  34 #define DE4X5_SICR   iobase+(0x068 << lp->bus)  /* SIA Connectivity Register */
  35 #define DE4X5_STRR   iobase+(0x070 << lp->bus)  /* SIA TX/RX Register */
  36 #define DE4X5_SIGR   iobase+(0x078 << lp->bus)  /* SIA General Register */
  37
  38 /*
  39 ** EISA Register Address Map
  40 */
  41 #define EISA_ID      iobase+0x0c80   /* EISA ID Registers */
  42 #define EISA_ID0     iobase+0x0c80   /* EISA ID Register 0 */
  43 #define EISA_ID1     iobase+0x0c81   /* EISA ID Register 1 */
  44 #define EISA_ID2     iobase+0x0c82   /* EISA ID Register 2 */
  45 #define EISA_ID3     iobase+0x0c83   /* EISA ID Register 3 */
  46 #define EISA_CR      iobase+0x0c84   /* EISA Control Register */
  47 #define EISA_REG0    iobase+0x0c88   /* EISA Configuration Register 0 */
  48 #define EISA_REG1    iobase+0x0c89   /* EISA Configuration Register 1 */
  49 #define EISA_REG2    iobase+0x0c8a   /* EISA Configuration Register 2 */
  50 #define EISA_REG3    iobase+0x0c8f   /* EISA Configuration Register 3 */
  51 #define EISA_APROM   iobase+0x0c90   /* Ethernet Address PROM */
  52
  53 /*
  54 ** PCI/EISA Configuration Registers Address Map
  55 */
  56 #define PCI_CFID     iobase+0x0008   /* PCI Configuration ID Register */
  57 #define PCI_CFCS     iobase+0x000c   /* PCI Command/Status Register */
  58 #define PCI_CFRV     iobase+0x0018   /* PCI Revision Register */
  59 #define PCI_CFLT     iobase+0x001c   /* PCI Latency Timer Register */
  60 #define PCI_CBIO     iobase+0x0028   /* PCI Base I/O Register */
  61 #define PCI_CBMA     iobase+0x002c   /* PCI Base Memory Address Register */
  62 #define PCI_CBER     iobase+0x0030   /* PCI Expansion ROM Base Address Reg. */
  63 #define PCI_CFIT     iobase+0x003c   /* PCI Configuration Interrupt Register */
  64 #define PCI_CFDA     iobase+0x0040   /* PCI Driver Area Register */
  65 #define PCI_CFDD     iobase+0x0041   /* PCI Driver Dependent Area Register */
  66 #define PCI_CFPM     iobase+0x0043   /* PCI Power Management Area Register */
  67
  68 /*
  69 ** EISA Configuration Register 0 bit definitions
  70 */
  71 #define ER0_BSW       0x80           /* EISA Bus Slave Width, 1: 32 bits */
  72 #define ER0_BMW       0x40           /* EISA Bus Master Width, 1: 32 bits */
  73 #define ER0_EPT       0x20           /* EISA PREEMPT Time, 0: 23 BCLKs */
  74 #define ER0_ISTS      0x10           /* Interrupt Status (X) */
  75 #define ER0_LI        0x08           /* Latch Interrupts */
  76 #define ER0_INTL      0x06           /* INTerrupt Level */
  77 #define ER0_INTT      0x01           /* INTerrupt Type, 0: Level, 1: Edge */
  78
  79 /*
  80 ** EISA Configuration Register 1 bit definitions
  81 */
  82 #define ER1_IAM       0xe0           /* ISA Address Mode */
  83 #define ER1_IAE       0x10           /* ISA Addressing Enable */
  84 #define ER1_UPIN      0x0f           /* User Pins */
  85
  86 /*
  87 ** EISA Configuration Register 2 bit definitions
  88 */
  89 #define ER2_BRS       0xc0           /* Boot ROM Size */
  90 #define ER2_BRA       0x3c           /* Boot ROM Address <16:13> */
  91
  92 /*
  93 ** EISA Configuration Register 3 bit definitions
  94 */
  95 #define ER3_BWE       0x40           /* Burst Write Enable */
  96 #define ER3_BRE       0x04           /* Burst Read Enable */
  97 #define ER3_LSR       0x02           /* Local Software Reset */
  98
  99 /*
 100 ** PCI Configuration ID Register (PCI_CFID). The Device IDs are left
 101 ** shifted 8 bits to allow detection of DC21142 and DC21143 variants with
 102 ** the configuration revision register step number.
 103 */
 104 #define CFID_DID    0xff00           /* Device ID */
 105 #define CFID_VID    0x00ff           /* Vendor ID */
 106 #define DC21040_DID 0x0200           /* Unique Device ID # */
 107 #define DC21040_VID 0x1011           /* DC21040 Manufacturer */
 108 #define DC21041_DID 0x1400           /* Unique Device ID # */
 109 #define DC21041_VID 0x1011           /* DC21041 Manufacturer */
 110 #define DC21140_DID 0x0900           /* Unique Device ID # */
 111 #define DC21140_VID 0x1011           /* DC21140 Manufacturer */
 112 #define DC2114x_DID 0x1900           /* Unique Device ID # */
 113 #define DC2114x_VID 0x1011           /* DC2114[23] Manufacturer */
 114
 115 /*
 116 ** Chipset defines
 117 */
 118 #define DC21040     DC21040_DID
 119 #define DC21041     DC21041_DID
 120 #define DC21140     DC21140_DID
 121 #define DC2114x     DC2114x_DID
 122 #define DC21142     (DC2114x_DID | 0x0010)
 123 #define DC21143     (DC2114x_DID | 0x0030)
 124 #define DC2114x_BRK 0x0020           /* CFRV break between DC21142 & DC21143 */
 125
 126 #define is_DC21040 ((vendor == DC21040_VID) && (device == DC21040_DID))
 127 #define is_DC21041 ((vendor == DC21041_VID) && (device == DC21041_DID))
 128 #define is_DC21140 ((vendor == DC21140_VID) && (device == DC21140_DID))
 129 #define is_DC2114x ((vendor == DC2114x_VID) && (device == DC2114x_DID))
 130 #define is_DC21142 ((vendor == DC2114x_VID) && (device == DC21142))
 131 #define is_DC21143 ((vendor == DC2114x_VID) && (device == DC21143))
 132
 133 /*
 134 ** PCI Configuration Command/Status Register (PCI_CFCS)
 135 */
 136 #define CFCS_DPE    0x80000000       /* Detected Parity Error (S) */
 137 #define CFCS_SSE    0x40000000       /* Signal System Error   (S) */
 138 #define CFCS_RMA    0x20000000       /* Receive Master Abort  (S) */
 139 #define CFCS_RTA    0x10000000       /* Receive Target Abort  (S) */
 140 #define CFCS_DST    0x06000000       /* DEVSEL Timing         (S) */
 141 #define CFCS_DPR    0x01000000       /* Data Parity Report    (S) */
 142 #define CFCS_FBB    0x00800000       /* Fast Back-To-Back     (S) */
 143 #define CFCS_SEE    0x00000100       /* System Error Enable   (C) */
 144 #define CFCS_PER    0x00000040       /* Parity Error Response (C) */
 145 #define CFCS_MO     0x00000004       /* Master Operation      (C) */
 146 #define CFCS_MSA    0x00000002       /* Memory Space Access   (C) */
 147 #define CFCS_IOSA   0x00000001       /* I/O Space Access      (C) */
 148
 149 /*
 150 ** PCI Configuration Revision Register (PCI_CFRV)
 151 */
 152 #define CFRV_BC     0xff000000       /* Base Class */
 153 #define CFRV_SC     0x00ff0000       /* Subclass */
 154 #define CFRV_RN     0x000000f0       /* Revision Number */
 155 #define CFRV_SN     0x0000000f       /* Step Number */
 156 #define BASE_CLASS  0x02000000       /* Indicates Network Controller */
 157 #define SUB_CLASS   0x00000000       /* Indicates Ethernet Controller */
 158 #define STEP_NUMBER 0x00000020       /* Increments for future chips */
 159 #define REV_NUMBER  0x00000003       /* 0x00, 0x01, 0x02, 0x03: Rev in Step */
 160 #define CFRV_MASK   0xffff0000       /* Register mask */
 161
 162 /*
 163 ** PCI Configuration Latency Timer Register (PCI_CFLT)
 164 */
 165 #define CFLT_BC     0x0000ff00       /* Latency Timer bits */
 166
 167 /*
 168 ** PCI Configuration Base I/O Address Register (PCI_CBIO)
 169 */
 170 #define CBIO_MASK   -128             /* Base I/O Address Mask */
 171 #define CBIO_IOSI   0x00000001       /* I/O Space Indicator (RO, value is 1) */
 172
 173 /*
 174 ** PCI Configuration Card Information Structure Register (PCI_CCIS)
 175 */
 176 #define CCIS_ROMI   0xf0000000       /* ROM Image */
 177 #define CCIS_ASO    0x0ffffff8       /* Address Space Offset */
 178 #define CCIS_ASI    0x00000007       /* Address Space Indicator */
 179
 180 /*
 181 ** PCI Configuration Subsystem ID Register (PCI_SSID)
 182 */
 183 #define SSID_SSID   0xffff0000       /* Subsystem ID */
 184 #define SSID_SVID   0x0000ffff       /* Subsystem Vendor ID */
 185
 186 /*
 187 ** PCI Configuration Expansion ROM Base Address Register (PCI_CBER)
 188 */
 189 #define CBER_MASK   0xfffffc00       /* Expansion ROM Base Address Mask */
 190 #define CBER_ROME   0x00000001       /* ROM Enable */
 191
 192 /*
 193 ** PCI Configuration Interrupt Register (PCI_CFIT)
 194 */
 195 #define CFIT_MXLT   0xff000000       /* MAX_LAT Value (0.25us periods) */
 196 #define CFIT_MNGT   0x00ff0000       /* MIN_GNT Value (0.25us periods) */
 197 #define CFIT_IRQP   0x0000ff00       /* Interrupt Pin */
 198 #define CFIT_IRQL   0x000000ff       /* Interrupt Line */
 199
 200 /*
 201 ** PCI Configuration Power Management Area Register (PCI_CFPM)
 202 */
 203 #define SLEEP       0x80             /* Power Saving Sleep Mode */
 204 #define SNOOZE      0x40             /* Power Saving Snooze Mode */
 205 #define WAKEUP      0x00             /* Power Saving Wakeup */
 206
 207 #define PCI_CFDA_DSU 0x41            /* 8 bit Configuration Space Address */
 208 #define PCI_CFDA_PSM 0x43            /* 8 bit Configuration Space Address */
 209
 210 /*
 211 ** DC21040 Bus Mode Register (DE4X5_BMR)
 212 */
 213 #define BMR_RML    0x00200000       /* [Memory] Read Multiple */
 214 #define BMR_DBO    0x00100000       /* Descriptor Byte Ordering (Endian) */
 215 #define BMR_TAP    0x000e0000       /* Transmit Automatic Polling */
 216 #define BMR_DAS    0x00010000       /* Diagnostic Address Space */
 217 #define BMR_CAL    0x0000c000       /* Cache Alignment */
 218 #define BMR_PBL    0x00003f00       /* Programmable Burst Length */
 219 #define BMR_BLE    0x00000080       /* Big/Little Endian */
 220 #define BMR_DSL    0x0000007c       /* Descriptor Skip Length */
 221 #define BMR_BAR    0x00000002       /* Bus ARbitration */
 222 #define BMR_SWR    0x00000001       /* Software Reset */
 223
 224                                     /* Timings here are for 10BASE-T/AUI only*/
 225 #define TAP_NOPOLL 0x00000000       /* No automatic polling */
 226 #define TAP_200US  0x00020000       /* TX automatic polling every 200us */
 227 #define TAP_800US  0x00040000       /* TX automatic polling every 800us */
 228 #define TAP_1_6MS  0x00060000       /* TX automatic polling every 1.6ms */
 229 #define TAP_12_8US 0x00080000       /* TX automatic polling every 12.8us */
 230 #define TAP_25_6US 0x000a0000       /* TX automatic polling every 25.6us */
 231 #define TAP_51_2US 0x000c0000       /* TX automatic polling every 51.2us */
 232 #define TAP_102_4US 0x000e0000      /* TX automatic polling every 102.4us */
 233
 234 #define CAL_NOUSE  0x00000000       /* Not used */
 235 #define CAL_8LONG  0x00004000       /* 8-longword alignment */
 236 #define CAL_16LONG 0x00008000       /* 16-longword alignment */
 237 #define CAL_32LONG 0x0000c000       /* 32-longword alignment */
 238
 239 #define PBL_0      0x00000000       /*  DMA burst length = amount in RX FIFO */
 240 #define PBL_1      0x00000100       /*  1 longword  DMA burst length */
 241 #define PBL_2      0x00000200       /*  2 longwords DMA burst length */
 242 #define PBL_4      0x00000400       /*  4 longwords DMA burst length */
 243 #define PBL_8      0x00000800       /*  8 longwords DMA burst length */
 244 #define PBL_16     0x00001000       /* 16 longwords DMA burst length */
 245 #define PBL_32     0x00002000       /* 32 longwords DMA burst length */
 246
 247 #define DSL_0      0x00000000       /*  0 longword  / descriptor */
 248 #define DSL_1      0x00000004       /*  1 longword  / descriptor */
 249 #define DSL_2      0x00000008       /*  2 longwords / descriptor */
 250 #define DSL_4      0x00000010       /*  4 longwords / descriptor */
 251 #define DSL_8      0x00000020       /*  8 longwords / descriptor */
 252 #define DSL_16     0x00000040       /* 16 longwords / descriptor */
 253 #define DSL_32     0x00000080       /* 32 longwords / descriptor */
 254
 255 /*
 256 ** DC21040 Transmit Poll Demand Register (DE4X5_TPD)
 257 */
 258 #define TPD        0x00000001       /* Transmit Poll Demand */
 259
 260 /*
 261 ** DC21040 Receive Poll Demand Register (DE4X5_RPD)
 262 */
 263 #define RPD        0x00000001       /* Receive Poll Demand */
 264
 265 /*
 266 ** DC21040 Receive Ring Base Address Register (DE4X5_RRBA)
 267 */
 268 #define RRBA       0xfffffffc       /* RX Descriptor List Start Address */
 269
 270 /*
 271 ** DC21040 Transmit Ring Base Address Register (DE4X5_TRBA)
 272 */
 273 #define TRBA       0xfffffffc       /* TX Descriptor List Start Address */
 274
 275 /*
 276 ** Status Register (DE4X5_STS)
 277 */
 278 #define STS_GPI    0x04000000       /* General Purpose Port Interrupt */
 279 #define STS_BE     0x03800000       /* Bus Error Bits */
 280 #define STS_TS     0x00700000       /* Transmit Process State */
 281 #define STS_RS     0x000e0000       /* Receive Process State */
 282 #define STS_NIS    0x00010000       /* Normal Interrupt Summary */
 283 #define STS_AIS    0x00008000       /* Abnormal Interrupt Summary */
 284 #define STS_ER     0x00004000       /* Early Receive */
 285 #define STS_FBE    0x00002000       /* Fatal Bus Error */
 286 #define STS_SE     0x00002000       /* System Error */
 287 #define STS_LNF    0x00001000       /* Link Fail */
 288 #define STS_FD     0x00000800       /* Full-Duplex Short Frame Received */
 289 #define STS_TM     0x00000800       /* Timer Expired (DC21041) */
 290 #define STS_ETI    0x00000400       /* Early Transmit Interrupt */
 291 #define STS_AT     0x00000400       /* AUI/TP Pin */
 292 #define STS_RWT    0x00000200       /* Receive Watchdog Time-Out */
 293 #define STS_RPS    0x00000100       /* Receive Process Stopped */
 294 #define STS_RU     0x00000080       /* Receive Buffer Unavailable */
 295 #define STS_RI     0x00000040       /* Receive Interrupt */
 296 #define STS_UNF    0x00000020       /* Transmit Underflow */
 297 #define STS_LNP    0x00000010       /* Link Pass */
 298 #define STS_ANC    0x00000010       /* Autonegotiation Complete */
 299 #define STS_TJT    0x00000008       /* Transmit Jabber Time-Out */
 300 #define STS_TU     0x00000004       /* Transmit Buffer Unavailable */
 301 #define STS_TPS    0x00000002       /* Transmit Process Stopped */
 302 #define STS_TI     0x00000001       /* Transmit Interrupt */
 303
 304 #define EB_PAR     0x00000000       /* Parity Error */
 305 #define EB_MA      0x00800000       /* Master Abort */
 306 #define EB_TA      0x01000000       /* Target Abort */
 307 #define EB_RES0    0x01800000       /* Reserved */
 308 #define EB_RES1    0x02000000       /* Reserved */
 309
 310 #define TS_STOP    0x00000000       /* Stopped */
 311 #define TS_FTD     0x00100000       /* Fetch Transmit Descriptor */
 312 #define TS_WEOT    0x00200000       /* Wait for End Of Transmission */
 313 #define TS_QDAT    0x00300000       /* Queue skb data into TX FIFO */
 314 #define TS_RES     0x00400000       /* Reserved */
 315 #define TS_SPKT    0x00500000       /* Setup Packet */
 316 #define TS_SUSP    0x00600000       /* Suspended */
 317 #define TS_CLTD    0x00700000       /* Close Transmit Descriptor */
 318
 319 #define RS_STOP    0x00000000       /* Stopped */
 320 #define RS_FRD     0x00020000       /* Fetch Receive Descriptor */
 321 #define RS_CEOR    0x00040000       /* Check for End of Receive Packet */
 322 #define RS_WFRP    0x00060000       /* Wait for Receive Packet */
 323 #define RS_SUSP    0x00080000       /* Suspended */
 324 #define RS_CLRD    0x000a0000       /* Close Receive Descriptor */
 325 #define RS_FLUSH   0x000c0000       /* Flush RX FIFO */
 326 #define RS_QRFS    0x000e0000       /* Queue RX FIFO into RX Skb */
 327
 328 #define INT_CANCEL 0x0001ffff       /* For zeroing all interrupt sources */
 329
 330 /*
 331 ** Operation Mode Register (DE4X5_OMR)
 332 */
 333 #define OMR_SC     0x80000000       /* Special Capture Effect Enable */
 334 #define OMR_RA     0x40000000       /* Receive All */
 335 #define OMR_SDP    0x02000000       /* SD Polarity - MUST BE ASSERTED */
 336 #define OMR_SCR    0x01000000       /* Scrambler Mode */
 337 #define OMR_PCS    0x00800000       /* PCS Function */
 338 #define OMR_TTM    0x00400000       /* Transmit Threshold Mode */
 339 #define OMR_SF     0x00200000       /* Store and Forward */
 340 #define OMR_HBD    0x00080000       /* HeartBeat Disable */
 341 #define OMR_PS     0x00040000       /* Port Select */
 342 #define OMR_CA     0x00020000       /* Capture Effect Enable */
 343 #define OMR_BP     0x00010000       /* Back Pressure */
 344 #define OMR_TR     0x0000c000       /* Threshold Control Bits */
 345 #define OMR_ST     0x00002000       /* Start/Stop Transmission Command */
 346 #define OMR_FC     0x00001000       /* Force Collision Mode */
 347 #define OMR_OM     0x00000c00       /* Operating Mode */
 348 #define OMR_FDX    0x00000200       /* Full Duplex Mode */
 349 #define OMR_FKD    0x00000100       /* Flaky Oscillator Disable */
 350 #define OMR_PM     0x00000080       /* Pass All Multicast */
 351 #define OMR_PR     0x00000040       /* Promiscuous Mode */
 352 #define OMR_SB     0x00000020       /* Start/Stop Backoff Counter */
 353 #define OMR_IF     0x00000010       /* Inverse Filtering */
 354 #define OMR_PB     0x00000008       /* Pass Bad Frames */
 355 #define OMR_HO     0x00000004       /* Hash Only Filtering Mode */
 356 #define OMR_SR     0x00000002       /* Start/Stop Receive */
 357 #define OMR_HP     0x00000001       /* Hash/Perfect Receive Filtering Mode */
 358
 359 #define TR_72      0x00000000       /* Threshold set to 72 (128) bytes */
 360 #define TR_96      0x00004000       /* Threshold set to 96 (256) bytes */
 361 #define TR_128     0x00008000       /* Threshold set to 128 (512) bytes */
 362 #define TR_160     0x0000c000       /* Threshold set to 160 (1024) bytes */
 363
 364 #define OMR_DEF     (OMR_SDP)
 365 #define OMR_SIA     (OMR_SDP | OMR_TTM)
 366 #define OMR_SYM     (OMR_SDP | OMR_SCR | OMR_PCS | OMR_HBD | OMR_PS)
 367 #define OMR_MII_10  (OMR_SDP | OMR_TTM | OMR_PS)
 368 #define OMR_MII_100 (OMR_SDP | OMR_HBD | OMR_PS)
 369
 370 /*
 371 ** DC21040 Interrupt Mask Register (DE4X5_IMR)
 372 */
 373 #define IMR_GPM    0x04000000       /* General Purpose Port Mask */
 374 #define IMR_NIM    0x00010000       /* Normal Interrupt Summary Mask */
 375 #define IMR_AIM    0x00008000       /* Abnormal Interrupt Summary Mask */
 376 #define IMR_ERM    0x00004000       /* Early Receive Mask */
 377 #define IMR_FBM    0x00002000       /* Fatal Bus Error Mask */
 378 #define IMR_SEM    0x00002000       /* System Error Mask */
 379 #define IMR_LFM    0x00001000       /* Link Fail Mask */
 380 #define IMR_FDM    0x00000800       /* Full-Duplex (Short Frame) Mask */
 381 #define IMR_TMM    0x00000800       /* Timer Expired Mask (DC21041) */
 382 #define IMR_ETM    0x00000400       /* Early Transmit Interrupt Mask */
 383 #define IMR_ATM    0x00000400       /* AUI/TP Switch Mask */
 384 #define IMR_RWM    0x00000200       /* Receive Watchdog Time-Out Mask */
 385 #define IMR_RSM    0x00000100       /* Receive Stopped Mask */
 386 #define IMR_RUM    0x00000080       /* Receive Buffer Unavailable Mask */
 387 #define IMR_RIM    0x00000040       /* Receive Interrupt Mask */
 388 #define IMR_UNM    0x00000020       /* Underflow Interrupt Mask */
 389 #define IMR_ANM    0x00000010       /* Autonegotiation Complete Mask */
 390 #define IMR_LPM    0x00000010       /* Link Pass */
 391 #define IMR_TJM    0x00000008       /* Transmit Time-Out Jabber Mask */
 392 #define IMR_TUM    0x00000004       /* Transmit Buffer Unavailable Mask */
 393 #define IMR_TSM    0x00000002       /* Transmission Stopped Mask */
 394 #define IMR_TIM    0x00000001       /* Transmit Interrupt Mask */
 395
 396 /*
 397 ** Missed Frames and FIFO Overflow Counters (DE4X5_MFC)
 398 */
 399 #define MFC_FOCO   0x10000000       /* FIFO Overflow Counter Overflow Bit */
 400 #define MFC_FOC    0x0ffe0000       /* FIFO Overflow Counter Bits */
 401 #define MFC_OVFL   0x00010000       /* Missed Frames Counter Overflow Bit */
 402 #define MFC_CNTR   0x0000ffff       /* Missed Frames Counter Bits */
 403 #define MFC_FOCM   0x1ffe0000       /* FIFO Overflow Counter Mask */
 404
 405 /*
 406 ** DC21040 Ethernet Address PROM (DE4X5_APROM)
 407 */
 408 #define APROM_DN   0x80000000       /* Data Not Valid */
 409 #define APROM_DT   0x000000ff       /* Address Byte */
 410
 411 /*
 412 ** DC21041 Boot/Ethernet Address ROM (DE4X5_BROM)
 413 */
 414 #define BROM_MODE 0x00008000       /* MODE_1: 0,  MODE_0: 1  (read only) */
 415 #define BROM_RD   0x00004000       /* Read from Boot ROM */
 416 #define BROM_WR   0x00002000       /* Write to Boot ROM */
 417 #define BROM_BR   0x00001000       /* Select Boot ROM when set */
 418 #define BROM_SR   0x00000800       /* Select Serial ROM when set */
 419 #define BROM_REG  0x00000400       /* External Register Select */
 420 #define BROM_DT   0x000000ff       /* Data Byte */
 421
 422 /*
 423 ** DC21041 Serial/Ethernet Address ROM (DE4X5_SROM, DE4X5_MII)
 424 */
 425 #define MII_MDI   0x00080000       /* MII Management Data In */
 426 #define MII_MDO   0x00060000       /* MII Management Mode/Data Out */
 427 #define MII_MRD   0x00040000       /* MII Management Define Read Mode */
 428 #define MII_MWR   0x00000000       /* MII Management Define Write Mode */
 429 #define MII_MDT   0x00020000       /* MII Management Data Out */
 430 #define MII_MDC   0x00010000       /* MII Management Clock */
 431 #define MII_RD    0x00004000       /* Read from MII */
 432 #define MII_WR    0x00002000       /* Write to MII */
 433 #define MII_SEL   0x00000800       /* Select MII when RESET */
 434
 435 #define SROM_MODE 0x00008000       /* MODE_1: 0,  MODE_0: 1  (read only) */
 436 #define SROM_RD   0x00004000       /* Read from Boot ROM */
 437 #define SROM_WR   0x00002000       /* Write to Boot ROM */
 438 #define SROM_BR   0x00001000       /* Select Boot ROM when set */
 439 #define SROM_SR   0x00000800       /* Select Serial ROM when set */
 440 #define SROM_REG  0x00000400       /* External Register Select */
 441 #define SROM_DT   0x000000ff       /* Data Byte */
 442
 443 #define DT_OUT    0x00000008       /* Serial Data Out */
 444 #define DT_IN     0x00000004       /* Serial Data In */
 445 #define DT_CLK    0x00000002       /* Serial ROM Clock */
 446 #define DT_CS     0x00000001       /* Serial ROM Chip Select */
 447
 448 #define MII_PREAMBLE 0xffffffff    /* MII Management Preamble */
 449 #define MII_TEST     0xaaaaaaaa    /* MII Test Signal */
 450 #define MII_STRD     0x06          /* Start of Frame+Op Code: use low nibble */
 451 #define MII_STWR     0x0a          /* Start of Frame+Op Code: use low nibble */
 452
 453 #define MII_CR       0x00          /* MII Management Control Register */
 454 #define MII_SR       0x01          /* MII Management Status Register */
 455 #define MII_ID0      0x02          /* PHY Identifier Register 0 */
 456 #define MII_ID1      0x03          /* PHY Identifier Register 1 */
 457 #define MII_ANA      0x04          /* Auto Negotiation Advertisement */
 458 #define MII_ANLPA    0x05          /* Auto Negotiation Link Partner Ability */
 459 #define MII_ANE      0x06          /* Auto Negotiation Expansion */
 460 #define MII_ANP      0x07          /* Auto Negotiation Next Page TX */
 461
 462 #define DE4X5_MAX_MII 32           /* Maximum address of MII PHY devices */
 463
 464 /*
 465 ** MII Management Control Register
 466 */
 467 #define MII_CR_RST  0x8000         /* RESET the PHY chip */
 468 #define MII_CR_LPBK 0x4000         /* Loopback enable */
 469 #define MII_CR_SPD  0x2000         /* 0: 10Mb/s; 1: 100Mb/s */
 470 #define MII_CR_10   0x0000         /* Set 10Mb/s */
 471 #define MII_CR_100  0x2000         /* Set 100Mb/s */
 472 #define MII_CR_ASSE 0x1000         /* Auto Speed Select Enable */
 473 #define MII_CR_PD   0x0800         /* Power Down */
 474 #define MII_CR_ISOL 0x0400         /* Isolate Mode */
 475 #define MII_CR_RAN  0x0200         /* Restart Auto Negotiation */
 476 #define MII_CR_FDM  0x0100         /* Full Duplex Mode */
 477 #define MII_CR_CTE  0x0080         /* Collision Test Enable */
 478
 479 /*
 480 ** MII Management Status Register
 481 */
 482 #define MII_SR_T4C  0x8000         /* 100BASE-T4 capable */
 483 #define MII_SR_TXFD 0x4000         /* 100BASE-TX Full Duplex capable */
 484 #define MII_SR_TXHD 0x2000         /* 100BASE-TX Half Duplex capable */
 485 #define MII_SR_TFD  0x1000         /* 10BASE-T Full Duplex capable */
 486 #define MII_SR_THD  0x0800         /* 10BASE-T Half Duplex capable */
 487 #define MII_SR_ASSC 0x0020         /* Auto Speed Selection Complete*/
 488 #define MII_SR_RFD  0x0010         /* Remote Fault Detected */
 489 #define MII_SR_ANC  0x0008         /* Auto Negotiation capable */
 490 #define MII_SR_LKS  0x0004         /* Link Status */
 491 #define MII_SR_JABD 0x0002         /* Jabber Detect */
 492 #define MII_SR_XC   0x0001         /* Extended Capabilities */
 493
 494 /*
 495 ** MII Management Auto Negotiation Advertisement Register
 496 */
 497 #define MII_ANA_TAF  0x03e0        /* Technology Ability Field */
 498 #define MII_ANA_T4AM 0x0200        /* T4 Technology Ability Mask */
 499 #define MII_ANA_TXAM 0x0180        /* TX Technology Ability Mask */
 500 #define MII_ANA_FDAM 0x0140        /* Full Duplex Technology Ability Mask */
 501 #define MII_ANA_HDAM 0x02a0        /* Half Duplex Technology Ability Mask */
 502 #define MII_ANA_100M 0x0380        /* 100Mb Technology Ability Mask */
 503 #define MII_ANA_10M  0x0060        /* 10Mb Technology Ability Mask */
 504 #define MII_ANA_CSMA 0x0001        /* CSMA-CD Capable */
 505
 506 /*
 507 ** MII Management Auto Negotiation Remote End Register
 508 */
 509 #define MII_ANLPA_NP   0x8000      /* Next Page (Enable) */
 510 #define MII_ANLPA_ACK  0x4000      /* Remote Acknowledge */
 511 #define MII_ANLPA_RF   0x2000      /* Remote Fault */
 512 #define MII_ANLPA_TAF  0x03e0      /* Technology Ability Field */
 513 #define MII_ANLPA_T4AM 0x0200      /* T4 Technology Ability Mask */
 514 #define MII_ANLPA_TXAM 0x0180      /* TX Technology Ability Mask */
 515 #define MII_ANLPA_FDAM 0x0140      /* Full Duplex Technology Ability Mask */
 516 #define MII_ANLPA_HDAM 0x02a0      /* Half Duplex Technology Ability Mask */
 517 #define MII_ANLPA_100M 0x0380      /* 100Mb Technology Ability Mask */
 518 #define MII_ANLPA_10M  0x0060      /* 10Mb Technology Ability Mask */
 519 #define MII_ANLPA_CSMA 0x0001      /* CSMA-CD Capable */
 520
 521 /*
 522 ** SROM Media Definitions (ABG SROM Section)
 523 */
 524 #define MEDIA_NWAY     0x0080      /* Nway (Auto Negotiation) on PHY */
 525 #define MEDIA_MII      0x0040      /* MII Present on the adapter */
 526 #define MEDIA_FIBRE    0x0008      /* Fibre Media present */
 527 #define MEDIA_AUI      0x0004      /* AUI Media present */
 528 #define MEDIA_TP       0x0002      /* TP Media present */
 529 #define MEDIA_BNC      0x0001      /* BNC Media present */
 530
 531 /*
 532 ** SROM Definitions (Digital Semiconductor Format)
 533 */
 534 #define SROM_SSVID     0x0000      /* Sub-system Vendor ID offset */
 535 #define SROM_SSID      0x0002      /* Sub-system ID offset */
 536 #define SROM_CISPL     0x0004      /* CardBus CIS Pointer low offset */
 537 #define SROM_CISPH     0x0006      /* CardBus CIS Pointer high offset */
 538 #define SROM_IDCRC     0x0010      /* ID Block CRC offset*/
 539 #define SROM_RSVD2     0x0011      /* ID Reserved 2 offset */
 540 #define SROM_SFV       0x0012      /* SROM Format Version offset */
 541 #define SROM_CCNT      0x0013      /* Controller Count offset */
 542 #define SROM_HWADD     0x0014      /* Hardware Address offset */
 543 #define SROM_MRSVD     0x007c      /* Manufacturer Reserved offset*/
 544 #define SROM_CRC       0x007e      /* SROM CRC offset */
 545
 546 /*
 547 ** SROM Media Connection Definitions
 548 */
 549 #define SROM_10BT      0x0000      /*  10BASE-T half duplex */
 550 #define SROM_10BTN     0x0100      /*  10BASE-T with Nway */
 551 #define SROM_10BTF     0x0204      /*  10BASE-T full duplex */
 552 #define SROM_10BTNLP   0x0400      /*  10BASE-T without Link Pass test */
 553 #define SROM_10B2      0x0001      /*  10BASE-2 (BNC) */
 554 #define SROM_10B5      0x0002      /*  10BASE-5 (AUI) */
 555 #define SROM_100BTH    0x0003      /*  100BASE-T half duplex */
 556 #define SROM_100BTF    0x0205      /*  100BASE-T full duplex */
 557 #define SROM_100BT4    0x0006      /*  100BASE-T4 */
 558 #define SROM_100BFX    0x0007      /*  100BASE-FX half duplex (Fiber) */
 559 #define SROM_M10BT     0x0009      /*  MII 10BASE-T half duplex */
 560 #define SROM_M10BTF    0x020a      /*  MII 10BASE-T full duplex */
 561 #define SROM_M100BT    0x000d      /*  MII 100BASE-T half duplex */
 562 #define SROM_M100BTF   0x020e      /*  MII 100BASE-T full duplex */
 563 #define SROM_M100BT4   0x000f      /*  MII 100BASE-T4 */
 564 #define SROM_M100BF    0x0010      /*  MII 100BASE-FX half duplex */
 565 #define SROM_M100BFF   0x0211      /*  MII 100BASE-FX full duplex */
 566 #define SROM_PDA       0x0800      /*  Powerup & Dynamic Autosense */
 567 #define SROM_PAO       0x8800      /*  Powerup Autosense Only */
 568 #define SROM_NSMI      0xffff      /*  No Selected Media Information */
 569
 570 /*
 571 ** SROM Media Definitions
 572 */
 573 #define SROM_10BASET   0x0000      /*  10BASE-T half duplex */
 574 #define SROM_10BASE2   0x0001      /*  10BASE-2 (BNC) */
 575 #define SROM_10BASE5   0x0002      /*  10BASE-5 (AUI) */
 576 #define SROM_100BASET  0x0003      /*  100BASE-T half duplex */
 577 #define SROM_10BASETF  0x0004      /*  10BASE-T full duplex */
 578 #define SROM_100BASETF 0x0005      /*  100BASE-T full duplex */
 579 #define SROM_100BASET4 0x0006      /*  100BASE-T4 */
 580 #define SROM_100BASEF  0x0007      /*  100BASE-FX half duplex */
 581 #define SROM_100BASEFF 0x0008      /*  100BASE-FX full duplex */
 582
 583 #define BLOCK_LEN      0x7f        /* Extended blocks length mask */
 584 #define EXT_FIELD      0x40        /* Extended blocks extension field bit */
 585 #define MEDIA_CODE     0x3f        /* Extended blocks media code mask */
 586
 587 /*
 588 ** SROM Compact Format Block Masks
 589 */
 590 #define COMPACT_FI      0x80       /* Format Indicator */
 591 #define COMPACT_LEN     0x04       /* Length */
 592 #define COMPACT_MC      0x3f       /* Media Code */
 593
 594 /*
 595 ** SROM Extended Format Block Type 0 Masks
 596 */
 597 #define BLOCK0_FI      0x80        /* Format Indicator */
 598 #define BLOCK0_MCS     0x80        /* Media Code byte Sign */
 599 #define BLOCK0_MC      0x3f        /* Media Code */
 600
 601 /*
 602 ** DC21040 Full Duplex Register (DE4X5_FDR)
 603 */
 604 #define FDR_FDACV  0x0000ffff      /* Full Duplex Auto Configuration Value */
 605
 606 /*
 607 ** DC21041 General Purpose Timer Register (DE4X5_GPT)
 608 */
 609 #define GPT_CON  0x00010000        /* One shot: 0,  Continuous: 1 */
 610 #define GPT_VAL  0x0000ffff        /* Timer Value */
 611
 612 /*
 613 ** DC21140 General Purpose Register (DE4X5_GEP) (hardware dependent bits)
 614 */
 615 /* Valid ONLY for DE500 hardware */
 616 #define GEP_LNP  0x00000080        /* Link Pass               (input)        */
 617 #define GEP_SLNK 0x00000040        /* SYM LINK                (input)        */
 618 #define GEP_SDET 0x00000020        /* Signal Detect           (input)        */
 619 #define GEP_HRST 0x00000010        /* Hard RESET (to PHY)     (output)       */
 620 #define GEP_FDXD 0x00000008        /* Full Duplex Disable     (output)       */
 621 #define GEP_PHYL 0x00000004        /* PHY Loopback            (output)       */
 622 #define GEP_FLED 0x00000002        /* Force Activity LED on   (output)       */
 623 #define GEP_MODE 0x00000001        /* 0: 10Mb/s,  1: 100Mb/s                 */
 624 #define GEP_INIT 0x0000011f        /* Setup inputs (0) and outputs (1)       */
 625 #define GEP_CTRL 0x00000100        /* GEP control bit                        */
 626
 627 /*
 628 ** SIA Register Defaults
 629 */
 630 #define CSR13 0x00000001
 631 #define CSR14 0x0003ff7f           /* Autonegotiation disabled               */
 632 #define CSR15 0x00000008
 633
 634 /*
 635 ** SIA Status Register (DE4X5_SISR)
 636 */
 637 #define SISR_LPC   0xffff0000      /* Link Partner's Code Word               */
 638 #define SISR_LPN   0x00008000      /* Link Partner Negotiable                */
 639 #define SISR_ANS   0x00007000      /* Auto Negotiation Arbitration State     */
 640 #define SISR_NSN   0x00000800      /* Non Stable NLPs Detected (DC21041)     */
 641 #define SISR_TRF   0x00000800      /* Transmit Remote Fault                  */
 642 #define SISR_NSND  0x00000400      /* Non Stable NLPs Detected (DC21142)     */
 643 #define SISR_ANR_FDS 0x00000400    /* Auto Negotiate Restart/Full Duplex Sel.*/
 644 #define SISR_TRA   0x00000200      /* 10BASE-T Receive Port Activity         */
 645 #define SISR_NRA   0x00000200      /* Non Selected Port Receive Activity     */
 646 #define SISR_ARA   0x00000100      /* AUI Receive Port Activity              */
 647 #define SISR_SRA   0x00000100      /* Selected Port Receive Activity         */
 648 #define SISR_DAO   0x00000080      /* PLL All One                            */
 649 #define SISR_DAZ   0x00000040      /* PLL All Zero                           */
 650 #define SISR_DSP   0x00000020      /* PLL Self-Test Pass                     */
 651 #define SISR_DSD   0x00000010      /* PLL Self-Test Done                     */
 652 #define SISR_APS   0x00000008      /* Auto Polarity State                    */
 653 #define SISR_LKF   0x00000004      /* Link Fail Status                       */
 654 #define SISR_LS10  0x00000004      /* 10Mb/s Link Fail Status                */
 655 #define SISR_NCR   0x00000002      /* Network Connection Error               */
 656 #define SISR_LS100 0x00000002      /* 100Mb/s Link Fail Status               */
 657 #define SISR_PAUI  0x00000001      /* AUI_TP Indication                      */
 658 #define SISR_MRA   0x00000001      /* MII Receive Port Activity              */
 659
 660 #define ANS_NDIS   0x00000000      /* Nway disable                           */
 661 #define ANS_TDIS   0x00001000      /* Transmit Disable                       */
 662 #define ANS_ADET   0x00002000      /* Ability Detect                         */
 663 #define ANS_ACK    0x00003000      /* Acknowledge                            */
 664 #define ANS_CACK   0x00004000      /* Complete Acknowledge                   */
 665 #define ANS_NWOK   0x00005000      /* Nway OK - FLP Link Good                */
 666 #define ANS_LCHK   0x00006000      /* Link Check                             */
 667
 668 #define SISR_RST   0x00000301      /* CSR12 reset                            */
 669 #define SISR_ANR   0x00001301      /* Autonegotiation restart                */
 670
 671 /*
 672 ** SIA Connectivity Register (DE4X5_SICR)
 673 */
 674 #define SICR_SDM   0xffff0000       /* SIA Diagnostics Mode */
 675 #define SICR_OE57  0x00008000       /* Output Enable 5 6 7 */
 676 #define SICR_OE24  0x00004000       /* Output Enable 2 4 */
 677 #define SICR_OE13  0x00002000       /* Output Enable 1 3 */
 678 #define SICR_IE    0x00001000       /* Input Enable */
 679 #define SICR_EXT   0x00000000       /* SIA MUX Select External SIA Mode */
 680 #define SICR_D_SIA 0x00000400       /* SIA MUX Select Diagnostics - SIA Sigs */
 681 #define SICR_DPLL  0x00000800       /* SIA MUX Select Diagnostics - DPLL Sigs*/
 682 #define SICR_APLL  0x00000a00       /* SIA MUX Select Diagnostics - DPLL Sigs*/
 683 #define SICR_D_RxM 0x00000c00       /* SIA MUX Select Diagnostics - RxM Sigs */
 684 #define SICR_M_RxM 0x00000d00       /* SIA MUX Select Diagnostics - RxM Sigs */
 685 #define SICR_LNKT  0x00000e00       /* SIA MUX Select Diagnostics - Link Test*/
 686 #define SICR_SEL   0x00000f00       /* SIA MUX Select AUI or TP with LEDs */
 687 #define SICR_ASE   0x00000080       /* APLL Start Enable*/
 688 #define SICR_SIM   0x00000040       /* Serial Interface Input Multiplexer */
 689 #define SICR_ENI   0x00000020       /* Encoder Input Multiplexer */
 690 #define SICR_EDP   0x00000010       /* SIA PLL External Input Enable */
 691 #define SICR_AUI   0x00000008       /* 10Base-T (0) or AUI (1) */
 692 #define SICR_CAC   0x00000004       /* CSR Auto Configuration */
 693 #define SICR_PS    0x00000002       /* Pin AUI/TP Selection */
 694 #define SICR_SRL   0x00000001       /* SIA Reset */
 695 #define SIA_RESET  0x00000000       /* SIA Reset Value */
 696
 697 /*
 698 ** SIA Transmit and Receive Register (DE4X5_STRR)
 699 */
 700 #define STRR_TAS   0x00008000       /* 10Base-T/AUI Autosensing Enable */
 701 #define STRR_SPP   0x00004000       /* Set Polarity Plus */
 702 #define STRR_APE   0x00002000       /* Auto Polarity Enable */
 703 #define STRR_LTE   0x00001000       /* Link Test Enable */
 704 #define STRR_SQE   0x00000800       /* Signal Quality Enable */
 705 #define STRR_CLD   0x00000400       /* Collision Detect Enable */
 706 #define STRR_CSQ   0x00000200       /* Collision Squelch Enable */
 707 #define STRR_RSQ   0x00000100       /* Receive Squelch Enable */
 708 #define STRR_ANE   0x00000080       /* Auto Negotiate Enable */
 709 #define STRR_HDE   0x00000040       /* Half Duplex Enable */
 710 #define STRR_CPEN  0x00000030       /* Compensation Enable */
 711 #define STRR_LSE   0x00000008       /* Link Pulse Send Enable */
 712 #define STRR_DREN  0x00000004       /* Driver Enable */
 713 #define STRR_LBK   0x00000002       /* Loopback Enable */
 714 #define STRR_ECEN  0x00000001       /* Encoder Enable */
 715 #define STRR_RESET 0xffffffff       /* Reset value for STRR */
 716
 717 /*
 718 ** SIA General Register (DE4X5_SIGR)
 719 */
 720 #define SIGR_RMI   0x40000000       /* Receive Match Interrupt */
 721 #define SIGR_GI1   0x20000000       /* General Port Interrupt 1 */
 722 #define SIGR_GI0   0x10000000       /* General Port Interrupt 0 */
 723 #define SIGR_CWE   0x08000000       /* Control Write Enable */
 724 #define SIGR_RME   0x04000000       /* Receive Match Enable */
 725 #define SIGR_GEI1  0x02000000       /* GEP Interrupt Enable on Port 1 */
 726 #define SIGR_GEI0  0x01000000       /* GEP Interrupt Enable on Port 0 */
 727 #define SIGR_LGS3  0x00800000       /* LED/GEP3 Select */
 728 #define SIGR_LGS2  0x00400000       /* LED/GEP2 Select */
 729 #define SIGR_LGS1  0x00200000       /* LED/GEP1 Select */
 730 #define SIGR_LGS0  0x00100000       /* LED/GEP0 Select */
 731 #define SIGR_MD    0x000f0000       /* General Purpose Mode and Data */
 732 #define SIGR_LV2   0x00008000       /* General Purpose LED2 value */
 733 #define SIGR_LE2   0x00004000       /* General Purpose LED2 enable */
 734 #define SIGR_FRL   0x00002000       /* Force Receiver Low */
 735 #define SIGR_DPST  0x00001000       /* PLL Self Test Start */
 736 #define SIGR_LSD   0x00000800       /* LED Stretch Disable */
 737 #define SIGR_FLF   0x00000400       /* Force Link Fail */
 738 #define SIGR_FUSQ  0x00000200       /* Force Unsquelch */
 739 #define SIGR_TSCK  0x00000100       /* Test Clock */
 740 #define SIGR_LV1   0x00000080       /* General Purpose LED1 value */
 741 #define SIGR_LE1   0x00000040       /* General Purpose LED1 enable */
 742 #define SIGR_RWR   0x00000020       /* Receive Watchdog Release */
 743 #define SIGR_RWD   0x00000010       /* Receive Watchdog Disable */
 744 #define SIGR_ABM   0x00000008       /* BNC: 0,  AUI:1 */
 745 #define SIGR_JCK   0x00000004       /* Jabber Clock */
 746 #define SIGR_HUJ   0x00000002       /* Host Unjab */
 747 #define SIGR_JBD   0x00000001       /* Jabber Disable */
 748 #define SIGR_RESET 0xffff0000       /* Reset value for SIGR */
 749
 750 /*
 751 ** Receive Descriptor Bit Summary
 752 */
 753 #define R_OWN      0x80000000       /* Own Bit */
 754 #define RD_FF      0x40000000       /* Filtering Fail */
 755 #define RD_FL      0x3fff0000       /* Frame Length */
 756 #define RD_ES      0x00008000       /* Error Summary */
 757 #define RD_LE      0x00004000       /* Length Error */
 758 #define RD_DT      0x00003000       /* Data Type */
 759 #define RD_RF      0x00000800       /* Runt Frame */
 760 #define RD_MF      0x00000400       /* Multicast Frame */
 761 #define RD_FS      0x00000200       /* First Descriptor */
 762 #define RD_LS      0x00000100       /* Last Descriptor */
 763 #define RD_TL      0x00000080       /* Frame Too Long */
 764 #define RD_CS      0x00000040       /* Collision Seen */
 765 #define RD_FT      0x00000020       /* Frame Type */
 766 #define RD_RJ      0x00000010       /* Receive Watchdog */
 767 #define RD_RE      0x00000008       /* Report on MII Error */
 768 #define RD_DB      0x00000004       /* Dribbling Bit */
 769 #define RD_CE      0x00000002       /* CRC Error */
 770 #define RD_OF      0x00000001       /* Overflow */
 771
 772 #define RD_RER     0x02000000       /* Receive End Of Ring */
 773 #define RD_RCH     0x01000000       /* Second Address Chained */
 774 #define RD_RBS2    0x003ff800       /* Buffer 2 Size */
 775 #define RD_RBS1    0x000007ff       /* Buffer 1 Size */
 776
 777 /*
 778 ** Transmit Descriptor Bit Summary
 779 */
 780 #define T_OWN      0x80000000       /* Own Bit */
 781 #define TD_ES      0x00008000       /* Error Summary */
 782 #define TD_TO      0x00004000       /* Transmit Jabber Time-Out */
 783 #define TD_LO      0x00000800       /* Loss Of Carrier */
 784 #define TD_NC      0x00000400       /* No Carrier */
 785 #define TD_LC      0x00000200       /* Late Collision */
 786 #define TD_EC      0x00000100       /* Excessive Collisions */
 787 #define TD_HF      0x00000080       /* Heartbeat Fail */
 788 #define TD_CC      0x00000078       /* Collision Counter */
 789 #define TD_LF      0x00000004       /* Link Fail */
 790 #define TD_UF      0x00000002       /* Underflow Error */
 791 #define TD_DE      0x00000001       /* Deferred */
 792
 793 #define TD_IC      0x80000000       /* Interrupt On Completion */
 794 #define TD_LS      0x40000000       /* Last Segment */
 795 #define TD_FS      0x20000000       /* First Segment */
 796 #define TD_FT1     0x10000000       /* Filtering Type */
 797 #define TD_SET     0x08000000       /* Setup Packet */
 798 #define TD_AC      0x04000000       /* Add CRC Disable */
 799 #define TD_TER     0x02000000       /* Transmit End Of Ring */
 800 #define TD_TCH     0x01000000       /* Second Address Chained */
 801 #define TD_DPD     0x00800000       /* Disabled Padding */
 802 #define TD_FT0     0x00400000       /* Filtering Type */
 803 #define TD_TBS2    0x003ff800       /* Buffer 2 Size */
 804 #define TD_TBS1    0x000007ff       /* Buffer 1 Size */
 805
 806 #define PERFECT_F  0x00000000
 807 #define HASH_F     TD_FT0
 808 #define INVERSE_F  TD_FT1
 809 #define HASH_O_F   (TD_FT1 | TD_F0)
 810
 811 /*
 812 ** Media / mode state machine definitions
 813 ** User selectable:
 814 */
 815 #define TP              0x0040     /* 10Base-T (now equiv to _10Mb)        */
 816 #define TP_NW           0x0002     /* 10Base-T with Nway                   */
 817 #define BNC             0x0004     /* Thinwire                             */
 818 #define AUI             0x0008     /* Thickwire                            */
 819 #define BNC_AUI         0x0010     /* BNC/AUI on DC21040 indistinguishable */
 820 #define _10Mb           0x0040     /* 10Mb/s Ethernet                      */
 821 #define _100Mb          0x0080     /* 100Mb/s Ethernet                     */
 822 #define AUTO            0x4000     /* Auto sense the media or speed        */
 823
 824 /*
 825 ** Internal states
 826 */
 827 #define NC              0x0000     /* No Connection                        */
 828 #define ANS             0x0020     /* Intermediate AutoNegotiation State   */
 829 #define SPD_DET         0x0100     /* Parallel speed detection             */
 830 #define INIT            0x0200     /* Initial state                        */
 831 #define EXT_SIA         0x0400     /* External SIA for motherboard chip    */
 832 #define ANS_SUSPECT     0x0802     /* Suspect the ANS (TP) port is down    */
 833 #define TP_SUSPECT      0x0803     /* Suspect the TP port is down          */
 834 #define BNC_AUI_SUSPECT 0x0804     /* Suspect the BNC or AUI port is down  */
 835 #define EXT_SIA_SUSPECT 0x0805     /* Suspect the EXT SIA port is down     */
 836 #define BNC_SUSPECT     0x0806     /* Suspect the BNC port is down         */
 837 #define AUI_SUSPECT     0x0807     /* Suspect the AUI port is down         */
 838 #define MII             0x1000     /* MII on the 21143                     */
 839
 840 #define TIMER_CB        0x80000000 /* Timer callback detection             */
 841
 842 /*
 843 ** DE4X5 DEBUG Options
 844 */
 845 #define DEBUG_NONE      0x0000     /* No DEBUG messages */
 846 #define DEBUG_VERSION   0x0001     /* Print version message */
 847 #define DEBUG_MEDIA     0x0002     /* Print media messages */
 848 #define DEBUG_TX        0x0004     /* Print TX (queue_pkt) messages */
 849 #define DEBUG_RX        0x0008     /* Print RX (de4x5_rx) messages */
 850 #define DEBUG_SROM      0x0010     /* Print SROM messages */
 851 #define DEBUG_MII       0x0020     /* Print MII messages */
 852 #define DEBUG_OPEN      0x0040     /* Print de4x5_open() messages */
 853 #define DEBUG_CLOSE     0x0080     /* Print de4x5_close() messages */
 854 #define DEBUG_PCICFG    0x0100
 855 #define DEBUG_ALL       0x01ff
 856
 857 /*
 858 ** Miscellaneous
 859 */
 860 #define PCI  0
 861 #define EISA 1
 862
 863 #define DE4X5_HASH_TABLE_LEN   512       /* Bits */
 864 #define DE4X5_HASH_BITS        0x01ff    /* 9 LS bits */
 865
 866 #define SETUP_FRAME_LEN  192       /* Bytes */
 867 #define IMPERF_PA_OFFSET 156       /* Bytes */
 868
 869 #define POLL_DEMAND          1
 870
 871 #define LOST_MEDIA_THRESHOLD 3
 872
 873 #define MASK_INTERRUPTS      1
 874 #define UNMASK_INTERRUPTS    0
 875
 876 #define DE4X5_STRLEN         8
 877
 878 #define DE4X5_INIT           0     /* Initialisation time */
 879 #define DE4X5_RUN            1     /* Run time */
 880
 881 #define DE4X5_SAVE_STATE     0
 882 #define DE4X5_RESTORE_STATE  1
 883
 884 /*
 885 ** Address Filtering Modes
 886 */
 887 #define PERFECT              0     /* 16 perfect physical addresses */
 888 #define HASH_PERF            1     /* 1 perfect, 512 multicast addresses */
 889 #define PERFECT_REJ          2     /* Reject 16 perfect physical addresses */
 890 #define ALL_HASH             3     /* Hashes all physical & multicast addrs */
 891
 892 #define ALL                  0     /* Clear out all the setup frame */
 893 #define PHYS_ADDR_ONLY       1     /* Update the physical address only */
 894
 895 /*
 896 ** Adapter state
 897 */
 898 #define INITIALISED          0     /* After h/w initialised and mem alloc'd */
 899 #define CLOSED               1     /* Ready for opening */
 900 #define OPEN                 2     /* Running */
 901
 902 /*
 903 ** Various wait times
 904 */
 905 #define PDET_LINK_WAIT    1200    /* msecs to wait for link detect bits     */
 906 #define ANS_FINISH_WAIT   1000    /* msecs to wait for link detect bits     */
 907
 908 /*
 909 ** IEEE OUIs for various PHY vendor/chip combos - Reg 2 values only. Since
 910 ** the vendors seem split 50-50 on how to calculate the OUI register values
 911 ** anyway, just reading Reg2 seems reasonable for now [see de4x5_get_oui()].
 912 */
 913 #define NATIONAL_TX 0x2000
 914 #define BROADCOM_T4 0x03e0
 915 #define SEEQ_T4     0x0016
 916 #define CYPRESS_T4  0x0014
 917
 918 /*
 919 ** Speed Selection stuff
 920 */
 921 #define SET_10Mb {\
 922   if ((lp->phy[lp->active].id) && (!lp->useSROM || lp->useMII)) {\
 923     omr = inl(DE4X5_OMR) & ~(OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX);\
 924     if ((lp->tmp != MII_SR_ASSC) || (lp->autosense != AUTO)) {\
 925       mii_wr(MII_CR_10|(lp->fdx?MII_CR_FDM:0), MII_CR, lp->phy[lp->active].addr, DE4X5_MII);\
 926     }\
 927     omr |= ((lp->fdx ? OMR_FDX : 0) | OMR_TTM);\
 928     outl(omr, DE4X5_OMR);\
 929     if (!lp->useSROM) lp->cache.gep = 0;\
 930   } else if (lp->useSROM && !lp->useMII) {\
 931     omr = (inl(DE4X5_OMR) & ~(OMR_PS | OMR_HBD | OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX));\
 932     omr |= (lp->fdx ? OMR_FDX : 0);\
 933     outl(omr | (lp->infoblock_csr6 & ~(OMR_SCR | OMR_HBD)), DE4X5_OMR);\
 934   } else {\
 935     omr = (inl(DE4X5_OMR) & ~(OMR_PS | OMR_HBD | OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX));\
 936     omr |= (lp->fdx ? OMR_FDX : 0);\
 937     outl(omr | OMR_SDP | OMR_TTM, DE4X5_OMR);\
 938     lp->cache.gep = (lp->fdx ? 0 : GEP_FDXD);\
 939     gep_wr(lp->cache.gep, dev);\
 940   }\
 941 }
 942
 943 #define SET_100Mb {\
 944   if ((lp->phy[lp->active].id) && (!lp->useSROM || lp->useMII)) {\
 945     int fdx=0;\
 946     if (lp->phy[lp->active].id == NATIONAL_TX) {\
 947         mii_wr(mii_rd(0x18, lp->phy[lp->active].addr, DE4X5_MII) & ~0x2000,\
 948                       0x18, lp->phy[lp->active].addr, DE4X5_MII);\
 949     }\
 950     omr = inl(DE4X5_OMR) & ~(OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX);\
 951     sr = mii_rd(MII_SR, lp->phy[lp->active].addr, DE4X5_MII);\
 952     if (!(sr & MII_ANA_T4AM) && lp->fdx) fdx=1;\
 953     if ((lp->tmp != MII_SR_ASSC) || (lp->autosense != AUTO)) {\
 954       mii_wr(MII_CR_100|(fdx?MII_CR_FDM:0), MII_CR, lp->phy[lp->active].addr, DE4X5_MII);\
 955     }\
 956     if (fdx) omr |= OMR_FDX;\
 957     outl(omr, DE4X5_OMR);\
 958     if (!lp->useSROM) lp->cache.gep = 0;\
 959   } else if (lp->useSROM && !lp->useMII) {\
 960     omr = (inl(DE4X5_OMR) & ~(OMR_PS | OMR_HBD | OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX));\
 961     omr |= (lp->fdx ? OMR_FDX : 0);\
 962     outl(omr | lp->infoblock_csr6, DE4X5_OMR);\
 963   } else {\
 964     omr = (inl(DE4X5_OMR) & ~(OMR_PS | OMR_HBD | OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX));\
 965     omr |= (lp->fdx ? OMR_FDX : 0);\
 966     outl(omr | OMR_SDP | OMR_PS | OMR_HBD | OMR_PCS | OMR_SCR, DE4X5_OMR);\
 967     lp->cache.gep = (lp->fdx ? 0 : GEP_FDXD) | GEP_MODE;\
 968     gep_wr(lp->cache.gep, dev);\
 969   }\
 970 }
 971
 972 /* FIX ME so I don't jam 10Mb networks */
 973 #define SET_100Mb_PDET {\
 974   if ((lp->phy[lp->active].id) && (!lp->useSROM || lp->useMII)) {\
 975     mii_wr(MII_CR_100|MII_CR_ASSE, MII_CR, lp->phy[lp->active].addr, DE4X5_MII);\
 976     omr = (inl(DE4X5_OMR) & ~(OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX));\
 977     outl(omr, DE4X5_OMR);\
 978   } else if (lp->useSROM && !lp->useMII) {\
 979     omr = (inl(DE4X5_OMR) & ~(OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX));\
 980     outl(omr, DE4X5_OMR);\
 981   } else {\
 982     omr = (inl(DE4X5_OMR) & ~(OMR_PS | OMR_HBD | OMR_TTM | OMR_PCS | OMR_SCR | OMR_FDX));\
 983     outl(omr | OMR_SDP | OMR_PS | OMR_HBD | OMR_PCS, DE4X5_OMR);\
 984     lp->cache.gep = (GEP_FDXD | GEP_MODE);\
 985     gep_wr(lp->cache.gep, dev);\
 986   }\
 987 }
 988
 989 /*
 990 ** Include the IOCTL stuff
 991 */
 992 #include <linux/sockios.h>
 993
 994 struct de4x5_ioctl {
 995         unsigned short cmd;                /* Command to run */
 996         unsigned short len;                /* Length of the data buffer */
 997         unsigned char  __user *data;       /* Pointer to the data buffer */
 998 };
 999
1000 /*
1001 ** Recognised commands for the driver
1002 */
1003 #define DE4X5_GET_HWADDR        0x01 /* Get the hardware address */
1004 #define DE4X5_SET_HWADDR        0x02 /* Set the hardware address */
1005 /* 0x03 and 0x04 were used before and are obsoleted now. Don't use them. */
1006 #define DE4X5_SAY_BOO           0x05 /* Say "Boo!" to the kernel log file */
1007 #define DE4X5_GET_MCA           0x06 /* Get a multicast address */
1008 #define DE4X5_SET_MCA           0x07 /* Set a multicast address */
1009 #define DE4X5_CLR_MCA           0x08 /* Clear a multicast address */
1010 #define DE4X5_MCA_EN            0x09 /* Enable a multicast address group */
1011 #define DE4X5_GET_STATS         0x0a /* Get the driver statistics */
1012 #define DE4X5_CLR_STATS         0x0b /* Zero out the driver statistics */
1013 #define DE4X5_GET_OMR           0x0c /* Get the OMR Register contents */
1014 #define DE4X5_SET_OMR           0x0d /* Set the OMR Register contents */
1015 #define DE4X5_GET_REG           0x0e /* Get the DE4X5 Registers */
1016
1017 #define MOTO_SROM_BUG    (lp->active == 8 && (get_unaligned_le32(dev->dev_addr) & 0x00ffffff) == 0x3e0008)