Staging: strip: delete the driver
[linux/fpc-iii.git] / drivers / usb / musb / tusb6010.h
blob35c933a5d9914ffab782a0b45db2452932bb42fa
1 /*
2 * Definitions for TUSB6010 USB 2.0 OTG Dual Role controller
4 * Copyright (C) 2006 Nokia Corporation
5 * Tony Lindgren <tony@atomide.com>
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License version 2 as
9 * published by the Free Software Foundation.
12 #ifndef __TUSB6010_H__
13 #define __TUSB6010_H__
15 extern u8 tusb_get_revision(struct musb *musb);
17 #ifdef CONFIG_USB_TUSB6010
18 #define musb_in_tusb() 1
19 #else
20 #define musb_in_tusb() 0
21 #endif
23 #ifdef CONFIG_USB_TUSB_OMAP_DMA
24 #define tusb_dma_omap() 1
25 #else
26 #define tusb_dma_omap() 0
27 #endif
29 /* VLYNQ control register. 32-bit at offset 0x000 */
30 #define TUSB_VLYNQ_CTRL 0x004
32 /* Mentor Graphics OTG core registers. 8,- 16- and 32-bit at offset 0x400 */
33 #define TUSB_BASE_OFFSET 0x400
35 /* FIFO registers 32-bit at offset 0x600 */
36 #define TUSB_FIFO_BASE 0x600
38 /* Device System & Control registers. 32-bit at offset 0x800 */
39 #define TUSB_SYS_REG_BASE 0x800
41 #define TUSB_DEV_CONF (TUSB_SYS_REG_BASE + 0x000)
42 #define TUSB_DEV_CONF_USB_HOST_MODE (1 << 16)
43 #define TUSB_DEV_CONF_PROD_TEST_MODE (1 << 15)
44 #define TUSB_DEV_CONF_SOFT_ID (1 << 1)
45 #define TUSB_DEV_CONF_ID_SEL (1 << 0)
47 #define TUSB_PHY_OTG_CTRL_ENABLE (TUSB_SYS_REG_BASE + 0x004)
48 #define TUSB_PHY_OTG_CTRL (TUSB_SYS_REG_BASE + 0x008)
49 #define TUSB_PHY_OTG_CTRL_WRPROTECT (0xa5 << 24)
50 #define TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP (1 << 23)
51 #define TUSB_PHY_OTG_CTRL_OTG_VBUS_DET_EN (1 << 19)
52 #define TUSB_PHY_OTG_CTRL_OTG_SESS_END_EN (1 << 18)
53 #define TUSB_PHY_OTG_CTRL_TESTM2 (1 << 17)
54 #define TUSB_PHY_OTG_CTRL_TESTM1 (1 << 16)
55 #define TUSB_PHY_OTG_CTRL_TESTM0 (1 << 15)
56 #define TUSB_PHY_OTG_CTRL_TX_DATA2 (1 << 14)
57 #define TUSB_PHY_OTG_CTRL_TX_GZ2 (1 << 13)
58 #define TUSB_PHY_OTG_CTRL_TX_ENABLE2 (1 << 12)
59 #define TUSB_PHY_OTG_CTRL_DM_PULLDOWN (1 << 11)
60 #define TUSB_PHY_OTG_CTRL_DP_PULLDOWN (1 << 10)
61 #define TUSB_PHY_OTG_CTRL_OSC_EN (1 << 9)
62 #define TUSB_PHY_OTG_CTRL_PHYREF_CLKSEL(v) (((v) & 3) << 7)
63 #define TUSB_PHY_OTG_CTRL_PD (1 << 6)
64 #define TUSB_PHY_OTG_CTRL_PLL_ON (1 << 5)
65 #define TUSB_PHY_OTG_CTRL_EXT_RPU (1 << 4)
66 #define TUSB_PHY_OTG_CTRL_PWR_GOOD (1 << 3)
67 #define TUSB_PHY_OTG_CTRL_RESET (1 << 2)
68 #define TUSB_PHY_OTG_CTRL_SUSPENDM (1 << 1)
69 #define TUSB_PHY_OTG_CTRL_CLK_MODE (1 << 0)
71 /*OTG status register */
72 #define TUSB_DEV_OTG_STAT (TUSB_SYS_REG_BASE + 0x00c)
73 #define TUSB_DEV_OTG_STAT_PWR_CLK_GOOD (1 << 8)
74 #define TUSB_DEV_OTG_STAT_SESS_END (1 << 7)
75 #define TUSB_DEV_OTG_STAT_SESS_VALID (1 << 6)
76 #define TUSB_DEV_OTG_STAT_VBUS_VALID (1 << 5)
77 #define TUSB_DEV_OTG_STAT_VBUS_SENSE (1 << 4)
78 #define TUSB_DEV_OTG_STAT_ID_STATUS (1 << 3)
79 #define TUSB_DEV_OTG_STAT_HOST_DISCON (1 << 2)
80 #define TUSB_DEV_OTG_STAT_LINE_STATE (3 << 0)
81 #define TUSB_DEV_OTG_STAT_DP_ENABLE (1 << 1)
82 #define TUSB_DEV_OTG_STAT_DM_ENABLE (1 << 0)
84 #define TUSB_DEV_OTG_TIMER (TUSB_SYS_REG_BASE + 0x010)
85 # define TUSB_DEV_OTG_TIMER_ENABLE (1 << 31)
86 # define TUSB_DEV_OTG_TIMER_VAL(v) ((v) & 0x07ffffff)
87 #define TUSB_PRCM_REV (TUSB_SYS_REG_BASE + 0x014)
89 /* PRCM configuration register */
90 #define TUSB_PRCM_CONF (TUSB_SYS_REG_BASE + 0x018)
91 #define TUSB_PRCM_CONF_SFW_CPEN (1 << 24)
92 #define TUSB_PRCM_CONF_SYS_CLKSEL(v) (((v) & 3) << 16)
94 /* PRCM management register */
95 #define TUSB_PRCM_MNGMT (TUSB_SYS_REG_BASE + 0x01c)
96 #define TUSB_PRCM_MNGMT_SRP_FIX_TIMER(v) (((v) & 0xf) << 25)
97 #define TUSB_PRCM_MNGMT_SRP_FIX_EN (1 << 24)
98 #define TUSB_PRCM_MNGMT_VBUS_VALID_TIMER(v) (((v) & 0xf) << 20)
99 #define TUSB_PRCM_MNGMT_VBUS_VALID_FLT_EN (1 << 19)
100 #define TUSB_PRCM_MNGMT_DFT_CLK_DIS (1 << 18)
101 #define TUSB_PRCM_MNGMT_VLYNQ_CLK_DIS (1 << 17)
102 #define TUSB_PRCM_MNGMT_OTG_SESS_END_EN (1 << 10)
103 #define TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN (1 << 9)
104 #define TUSB_PRCM_MNGMT_OTG_ID_PULLUP (1 << 8)
105 #define TUSB_PRCM_MNGMT_15_SW_EN (1 << 4)
106 #define TUSB_PRCM_MNGMT_33_SW_EN (1 << 3)
107 #define TUSB_PRCM_MNGMT_5V_CPEN (1 << 2)
108 #define TUSB_PRCM_MNGMT_PM_IDLE (1 << 1)
109 #define TUSB_PRCM_MNGMT_DEV_IDLE (1 << 0)
111 /* Wake-up source clear and mask registers */
112 #define TUSB_PRCM_WAKEUP_SOURCE (TUSB_SYS_REG_BASE + 0x020)
113 #define TUSB_PRCM_WAKEUP_CLEAR (TUSB_SYS_REG_BASE + 0x028)
114 #define TUSB_PRCM_WAKEUP_MASK (TUSB_SYS_REG_BASE + 0x02c)
115 #define TUSB_PRCM_WAKEUP_RESERVED_BITS (0xffffe << 13)
116 #define TUSB_PRCM_WGPIO_7 (1 << 12)
117 #define TUSB_PRCM_WGPIO_6 (1 << 11)
118 #define TUSB_PRCM_WGPIO_5 (1 << 10)
119 #define TUSB_PRCM_WGPIO_4 (1 << 9)
120 #define TUSB_PRCM_WGPIO_3 (1 << 8)
121 #define TUSB_PRCM_WGPIO_2 (1 << 7)
122 #define TUSB_PRCM_WGPIO_1 (1 << 6)
123 #define TUSB_PRCM_WGPIO_0 (1 << 5)
124 #define TUSB_PRCM_WHOSTDISCON (1 << 4) /* Host disconnect */
125 #define TUSB_PRCM_WBUS (1 << 3) /* USB bus resume */
126 #define TUSB_PRCM_WNORCS (1 << 2) /* NOR chip select */
127 #define TUSB_PRCM_WVBUS (1 << 1) /* OTG PHY VBUS */
128 #define TUSB_PRCM_WID (1 << 0) /* OTG PHY ID detect */
130 #define TUSB_PULLUP_1_CTRL (TUSB_SYS_REG_BASE + 0x030)
131 #define TUSB_PULLUP_2_CTRL (TUSB_SYS_REG_BASE + 0x034)
132 #define TUSB_INT_CTRL_REV (TUSB_SYS_REG_BASE + 0x038)
133 #define TUSB_INT_CTRL_CONF (TUSB_SYS_REG_BASE + 0x03c)
134 #define TUSB_USBIP_INT_SRC (TUSB_SYS_REG_BASE + 0x040)
135 #define TUSB_USBIP_INT_SET (TUSB_SYS_REG_BASE + 0x044)
136 #define TUSB_USBIP_INT_CLEAR (TUSB_SYS_REG_BASE + 0x048)
137 #define TUSB_USBIP_INT_MASK (TUSB_SYS_REG_BASE + 0x04c)
138 #define TUSB_DMA_INT_SRC (TUSB_SYS_REG_BASE + 0x050)
139 #define TUSB_DMA_INT_SET (TUSB_SYS_REG_BASE + 0x054)
140 #define TUSB_DMA_INT_CLEAR (TUSB_SYS_REG_BASE + 0x058)
141 #define TUSB_DMA_INT_MASK (TUSB_SYS_REG_BASE + 0x05c)
142 #define TUSB_GPIO_INT_SRC (TUSB_SYS_REG_BASE + 0x060)
143 #define TUSB_GPIO_INT_SET (TUSB_SYS_REG_BASE + 0x064)
144 #define TUSB_GPIO_INT_CLEAR (TUSB_SYS_REG_BASE + 0x068)
145 #define TUSB_GPIO_INT_MASK (TUSB_SYS_REG_BASE + 0x06c)
147 /* NOR flash interrupt source registers */
148 #define TUSB_INT_SRC (TUSB_SYS_REG_BASE + 0x070)
149 #define TUSB_INT_SRC_SET (TUSB_SYS_REG_BASE + 0x074)
150 #define TUSB_INT_SRC_CLEAR (TUSB_SYS_REG_BASE + 0x078)
151 #define TUSB_INT_MASK (TUSB_SYS_REG_BASE + 0x07c)
152 #define TUSB_INT_SRC_TXRX_DMA_DONE (1 << 24)
153 #define TUSB_INT_SRC_USB_IP_CORE (1 << 17)
154 #define TUSB_INT_SRC_OTG_TIMEOUT (1 << 16)
155 #define TUSB_INT_SRC_VBUS_SENSE_CHNG (1 << 15)
156 #define TUSB_INT_SRC_ID_STATUS_CHNG (1 << 14)
157 #define TUSB_INT_SRC_DEV_WAKEUP (1 << 13)
158 #define TUSB_INT_SRC_DEV_READY (1 << 12)
159 #define TUSB_INT_SRC_USB_IP_TX (1 << 9)
160 #define TUSB_INT_SRC_USB_IP_RX (1 << 8)
161 #define TUSB_INT_SRC_USB_IP_VBUS_ERR (1 << 7)
162 #define TUSB_INT_SRC_USB_IP_VBUS_REQ (1 << 6)
163 #define TUSB_INT_SRC_USB_IP_DISCON (1 << 5)
164 #define TUSB_INT_SRC_USB_IP_CONN (1 << 4)
165 #define TUSB_INT_SRC_USB_IP_SOF (1 << 3)
166 #define TUSB_INT_SRC_USB_IP_RST_BABBLE (1 << 2)
167 #define TUSB_INT_SRC_USB_IP_RESUME (1 << 1)
168 #define TUSB_INT_SRC_USB_IP_SUSPEND (1 << 0)
170 /* NOR flash interrupt registers reserved bits. Must be written as 0 */
171 #define TUSB_INT_MASK_RESERVED_17 (0x3fff << 17)
172 #define TUSB_INT_MASK_RESERVED_13 (1 << 13)
173 #define TUSB_INT_MASK_RESERVED_8 (0xf << 8)
174 #define TUSB_INT_SRC_RESERVED_26 (0x1f << 26)
175 #define TUSB_INT_SRC_RESERVED_18 (0x3f << 18)
176 #define TUSB_INT_SRC_RESERVED_10 (0x03 << 10)
178 /* Reserved bits for NOR flash interrupt mask and clear register */
179 #define TUSB_INT_MASK_RESERVED_BITS (TUSB_INT_MASK_RESERVED_17 | \
180 TUSB_INT_MASK_RESERVED_13 | \
181 TUSB_INT_MASK_RESERVED_8)
183 /* Reserved bits for NOR flash interrupt status register */
184 #define TUSB_INT_SRC_RESERVED_BITS (TUSB_INT_SRC_RESERVED_26 | \
185 TUSB_INT_SRC_RESERVED_18 | \
186 TUSB_INT_SRC_RESERVED_10)
188 #define TUSB_GPIO_REV (TUSB_SYS_REG_BASE + 0x080)
189 #define TUSB_GPIO_CONF (TUSB_SYS_REG_BASE + 0x084)
190 #define TUSB_DMA_CTRL_REV (TUSB_SYS_REG_BASE + 0x100)
191 #define TUSB_DMA_REQ_CONF (TUSB_SYS_REG_BASE + 0x104)
192 #define TUSB_EP0_CONF (TUSB_SYS_REG_BASE + 0x108)
193 #define TUSB_DMA_EP_MAP (TUSB_SYS_REG_BASE + 0x148)
195 /* Offsets from each ep base register */
196 #define TUSB_EP_TX_OFFSET 0x10c /* EP_IN in docs */
197 #define TUSB_EP_RX_OFFSET 0x14c /* EP_OUT in docs */
198 #define TUSB_EP_MAX_PACKET_SIZE_OFFSET 0x188
200 #define TUSB_WAIT_COUNT (TUSB_SYS_REG_BASE + 0x1c8)
201 #define TUSB_SCRATCH_PAD (TUSB_SYS_REG_BASE + 0x1c4)
202 #define TUSB_PROD_TEST_RESET (TUSB_SYS_REG_BASE + 0x1d8)
204 /* Device System & Control register bitfields */
205 #define TUSB_INT_CTRL_CONF_INT_RELCYC(v) (((v) & 0x7) << 18)
206 #define TUSB_INT_CTRL_CONF_INT_POLARITY (1 << 17)
207 #define TUSB_INT_CTRL_CONF_INT_MODE (1 << 16)
208 #define TUSB_GPIO_CONF_DMAREQ(v) (((v) & 0x3f) << 24)
209 #define TUSB_DMA_REQ_CONF_BURST_SIZE(v) (((v) & 3) << 26)
210 #define TUSB_DMA_REQ_CONF_DMA_REQ_EN(v) (((v) & 0x3f) << 20)
211 #define TUSB_DMA_REQ_CONF_DMA_REQ_ASSER(v) (((v) & 0xf) << 16)
212 #define TUSB_EP0_CONFIG_SW_EN (1 << 8)
213 #define TUSB_EP0_CONFIG_DIR_TX (1 << 7)
214 #define TUSB_EP0_CONFIG_XFR_SIZE(v) ((v) & 0x7f)
215 #define TUSB_EP_CONFIG_SW_EN (1 << 31)
216 #define TUSB_EP_CONFIG_XFR_SIZE(v) ((v) & 0x7fffffff)
217 #define TUSB_PROD_TEST_RESET_VAL 0xa596
218 #define TUSB_EP_FIFO(ep) (TUSB_FIFO_BASE + (ep) * 0x20)
220 #define TUSB_DIDR1_LO (TUSB_SYS_REG_BASE + 0x1f8)
221 #define TUSB_DIDR1_HI (TUSB_SYS_REG_BASE + 0x1fc)
222 #define TUSB_DIDR1_HI_CHIP_REV(v) (((v) >> 17) & 0xf)
223 #define TUSB_DIDR1_HI_REV_20 0
224 #define TUSB_DIDR1_HI_REV_30 1
225 #define TUSB_DIDR1_HI_REV_31 2
227 #define TUSB_REV_10 0x10
228 #define TUSB_REV_20 0x20
229 #define TUSB_REV_30 0x30
230 #define TUSB_REV_31 0x31
232 #endif /* __TUSB6010_H__ */