Documentation/devicetree/bindings/mtd/davinci-nand.txt

   1 Device tree bindings for Texas instruments Davinci/Keystone NAND controller
   2
   3 This file provides information, what the device node for the davinci/keystone
   4 NAND interface contains.
   5
   6 Documentation:
   7 Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
   8 Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
   9
  10 Required properties:
  11
  12 - compatible:                   "ti,davinci-nand"
  13                                 "ti,keystone-nand"
  14
  15 - reg:                          Contains 2 offset/length values:
  16                                 - offset and length for the access window.
  17                                 - offset and length for accessing the AEMIF
  18                                 control registers.
  19
  20 - ti,davinci-chipselect:        number of chipselect. Indicates on the
  21                                 davinci_nand driver which chipselect is used
  22                                 for accessing the nand.
  23                                 Can be in the range [0-3].
  24
  25 Recommended properties :
  26
  27 - ti,davinci-mask-ale:          mask for ALE. Needed for executing address
  28                                 phase. These offset will be added to the base
  29                                 address for the chip select space the NAND Flash
  30                                 device is connected to.
  31                                 If not set equal to 0x08.
  32
  33 - ti,davinci-mask-cle:          mask for CLE. Needed for executing command
  34                                 phase. These offset will be added to the base
  35                                 address for the chip select space the NAND Flash
  36                                 device is connected to.
  37                                 If not set equal to 0x10.
  38
  39 - ti,davinci-mask-chipsel:      mask for chipselect address. Needed to mask
  40                                 addresses for given chipselect.
  41
  42 - nand-ecc-mode:                operation mode of the NAND ecc mode. ECC mode
  43                                 valid values for davinci driver:
  44                                 - "none"
  45                                 - "soft"
  46                                 - "hw"
  47
  48 - ti,davinci-ecc-bits:          used ECC bits, currently supported 1 or 4.
  49
  50 - nand-bus-width:               buswidth 8 or 16. If not present 8.
  51
  52 - nand-on-flash-bbt:            use flash based bad block table support. OOB
  53                                 identifier is saved in OOB area. If not present
  54                                 false.
  55
  56 Deprecated properties:
  57
  58 - ti,davinci-ecc-mode:          operation mode of the NAND ecc mode. ECC mode
  59                                 valid values for davinci driver:
  60                                 - "none"
  61                                 - "soft"
  62                                 - "hw"
  63
  64 - ti,davinci-nand-buswidth:     buswidth 8 or 16. If not present 8.
  65
  66 - ti,davinci-nand-use-bbt:      use flash based bad block table support. OOB
  67                                 identifier is saved in OOB area. If not present
  68                                 false.
  69
  70 Nand device bindings may contain additional sub-nodes describing partitions of
  71 the address space. See partition.txt for more detail. The NAND Flash timing
  72 values must be programmed in the chip select’s node of AEMIF
  73 memory-controller (see Documentation/devicetree/bindings/memory-controllers/
  74 davinci-aemif.txt).
  75
  76 Example(da850 EVM ):
  77
  78 nand_cs3@62000000 {
  79         compatible = "ti,davinci-nand";
  80         reg = <0x62000000 0x807ff
  81                0x68000000 0x8000>;
  82         ti,davinci-chipselect = <1>;
  83         ti,davinci-mask-ale = <0>;
  84         ti,davinci-mask-cle = <0>;
  85         ti,davinci-mask-chipsel = <0>;
  86         nand-ecc-mode = "hw";
  87         ti,davinci-ecc-bits = <4>;
  88         nand-on-flash-bbt;
  89
  90         partition@180000 {
  91                 label = "ubifs";
  92                 reg = <0x180000 0x7e80000>;
  93         };
  94 };