drm/panfrost: Remove set but not used variable 'bo'

[linux/fpc-iii.git] / include / linux / mtd / rawnand.h

/* SPDX-License-Identifier: GPL-2.0-only */
/*
 *  Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org>
 *                        Steven J. Hill <sjhill@realitydiluted.com>
 *                        Thomas Gleixner <tglx@linutronix.de>
 *
 * Info:
 *      Contains standard defines and IDs for NAND flash devices
 *
 * Changelog:
 *      See git changelog.
 */
#ifndef __LINUX_MTD_RAWNAND_H
#define __LINUX_MTD_RAWNAND_H

#include <linux/mtd/mtd.h>
#include <linux/mtd/flashchip.h>
#include <linux/mtd/bbm.h>
#include <linux/mtd/jedec.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/onfi.h>
#include <linux/mutex.h>
#include <linux/of.h>
#include <linux/types.h>

struct nand_chip;

/* The maximum number of NAND chips in an array */
#define NAND_MAX_CHIPS          8

/*
 * Constants for hardware specific CLE/ALE/NCE function
 *
 * These are bits which can be or'ed to set/clear multiple
 * bits in one go.
 */
/* Select the chip by setting nCE to low */
#define NAND_NCE                0x01
/* Select the command latch by setting CLE to high */
#define NAND_CLE                0x02
/* Select the address latch by setting ALE to high */
#define NAND_ALE                0x04

#define NAND_CTRL_CLE           (NAND_NCE | NAND_CLE)
#define NAND_CTRL_ALE           (NAND_NCE | NAND_ALE)
#define NAND_CTRL_CHANGE        0x80

/*
 * Standard NAND flash commands
 */
#define NAND_CMD_READ0          0
#define NAND_CMD_READ1          1
#define NAND_CMD_RNDOUT         5
#define NAND_CMD_PAGEPROG       0x10
#define NAND_CMD_READOOB        0x50
#define NAND_CMD_ERASE1         0x60
#define NAND_CMD_STATUS         0x70
#define NAND_CMD_SEQIN          0x80
#define NAND_CMD_RNDIN          0x85
#define NAND_CMD_READID         0x90
#define NAND_CMD_ERASE2         0xd0
#define NAND_CMD_PARAM          0xec
#define NAND_CMD_GET_FEATURES   0xee
#define NAND_CMD_SET_FEATURES   0xef
#define NAND_CMD_RESET          0xff

/* Extended commands for large page devices */
#define NAND_CMD_READSTART      0x30
#define NAND_CMD_RNDOUTSTART    0xE0
#define NAND_CMD_CACHEDPROG     0x15

#define NAND_CMD_NONE           -1

/* Status bits */
#define NAND_STATUS_FAIL        0x01
#define NAND_STATUS_FAIL_N1     0x02
#define NAND_STATUS_TRUE_READY  0x20
#define NAND_STATUS_READY       0x40
#define NAND_STATUS_WP          0x80

#define NAND_DATA_IFACE_CHECK_ONLY      -1

/*
 * Constants for ECC_MODES
 */
typedef enum {
        NAND_ECC_NONE,
        NAND_ECC_SOFT,
        NAND_ECC_HW,
        NAND_ECC_HW_SYNDROME,
        NAND_ECC_HW_OOB_FIRST,
        NAND_ECC_ON_DIE,
} nand_ecc_modes_t;

enum nand_ecc_algo {
        NAND_ECC_UNKNOWN,
        NAND_ECC_HAMMING,
        NAND_ECC_BCH,
        NAND_ECC_RS,
};

/*
 * Constants for Hardware ECC
 */
/* Reset Hardware ECC for read */
#define NAND_ECC_READ           0
/* Reset Hardware ECC for write */
#define NAND_ECC_WRITE          1
/* Enable Hardware ECC before syndrome is read back from flash */
#define NAND_ECC_READSYN        2

/*
 * Enable generic NAND 'page erased' check. This check is only done when
 * ecc.correct() returns -EBADMSG.
 * Set this flag if your implementation does not fix bitflips in erased
 * pages and you want to rely on the default implementation.
 */
#define NAND_ECC_GENERIC_ERASED_CHECK   BIT(0)
#define NAND_ECC_MAXIMIZE               BIT(1)

/*
 * When using software implementation of Hamming, we can specify which byte
 * ordering should be used.
 */
#define NAND_ECC_SOFT_HAMMING_SM_ORDER  BIT(2)

/*
 * Option constants for bizarre disfunctionality and real
 * features.
 */
/* Buswidth is 16 bit */
#define NAND_BUSWIDTH_16        0x00000002
/* Chip has cache program function */
#define NAND_CACHEPRG           0x00000008
/*
 * Chip requires ready check on read (for auto-incremented sequential read).
 * True only for small page devices; large page devices do not support
 * autoincrement.
 */
#define NAND_NEED_READRDY       0x00000100

/* Chip does not allow subpage writes */
#define NAND_NO_SUBPAGE_WRITE   0x00000200

/* Device is one of 'new' xD cards that expose fake nand command set */
#define NAND_BROKEN_XD          0x00000400

/* Device behaves just like nand, but is readonly */
#define NAND_ROM                0x00000800

/* Device supports subpage reads */
#define NAND_SUBPAGE_READ       0x00001000

/*
 * Some MLC NANDs need data scrambling to limit bitflips caused by repeated
 * patterns.
 */
#define NAND_NEED_SCRAMBLING    0x00002000

/* Device needs 3rd row address cycle */
#define NAND_ROW_ADDR_3         0x00004000

/* Options valid for Samsung large page devices */
#define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG

/* Macros to identify the above */
#define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ))

/*
 * There are different places where the manufacturer stores the factory bad
 * block markers.
 *
 * Position within the block: Each of these pages needs to be checked for a
 * bad block marking pattern.
 */
#define NAND_BBM_FIRSTPAGE              0x01000000
#define NAND_BBM_SECONDPAGE             0x02000000
#define NAND_BBM_LASTPAGE               0x04000000

/* Position within the OOB data of the page */
#define NAND_BBM_POS_SMALL              5
#define NAND_BBM_POS_LARGE              0

/* Non chip related options */
/* This option skips the bbt scan during initialization. */
#define NAND_SKIP_BBTSCAN       0x00010000
/* Chip may not exist, so silence any errors in scan */
#define NAND_SCAN_SILENT_NODEV  0x00040000
/*
 * Autodetect nand buswidth with readid/onfi.
 * This suppose the driver will configure the hardware in 8 bits mode
 * when calling nand_scan_ident, and update its configuration
 * before calling nand_scan_tail.
 */
#define NAND_BUSWIDTH_AUTO      0x00080000
/*
 * This option could be defined by controller drivers to protect against
 * kmap'ed, vmalloc'ed highmem buffers being passed from upper layers
 */
#define NAND_USE_BOUNCE_BUFFER  0x00100000

/*
 * In case your controller is implementing ->legacy.cmd_ctrl() and is relying
 * on the default ->cmdfunc() implementation, you may want to let the core
 * handle the tCCS delay which is required when a column change (RNDIN or
 * RNDOUT) is requested.
 * If your controller already takes care of this delay, you don't need to set
 * this flag.
 */
#define NAND_WAIT_TCCS          0x00200000

/*
 * Whether the NAND chip is a boot medium. Drivers might use this information
 * to select ECC algorithms supported by the boot ROM or similar restrictions.
 */
#define NAND_IS_BOOT_MEDIUM     0x00400000

/*
 * Do not try to tweak the timings at runtime. This is needed when the
 * controller initializes the timings on itself or when it relies on
 * configuration done by the bootloader.
 */
#define NAND_KEEP_TIMINGS       0x00800000

/* Cell info constants */
#define NAND_CI_CHIPNR_MSK      0x03
#define NAND_CI_CELLTYPE_MSK    0x0C
#define NAND_CI_CELLTYPE_SHIFT  2

/**
 * struct nand_parameters - NAND generic parameters from the parameter page
 * @model: Model name
 * @supports_set_get_features: The NAND chip supports setting/getting features
 * @set_feature_list: Bitmap of features that can be set
 * @get_feature_list: Bitmap of features that can be get
 * @onfi: ONFI specific parameters
 */
struct nand_parameters {
        /* Generic parameters */
        const char *model;
        bool supports_set_get_features;
        DECLARE_BITMAP(set_feature_list, ONFI_FEATURE_NUMBER);
        DECLARE_BITMAP(get_feature_list, ONFI_FEATURE_NUMBER);

        /* ONFI parameters */
        struct onfi_params *onfi;
};

/* The maximum expected count of bytes in the NAND ID sequence */
#define NAND_MAX_ID_LEN 8

/**
 * struct nand_id - NAND id structure
 * @data: buffer containing the id bytes.
 * @len: ID length.
 */
struct nand_id {
        u8 data[NAND_MAX_ID_LEN];
        int len;
};

/**
 * struct nand_ecc_step_info - ECC step information of ECC engine
 * @stepsize: data bytes per ECC step
 * @strengths: array of supported strengths
 * @nstrengths: number of supported strengths
 */
struct nand_ecc_step_info {
        int stepsize;
        const int *strengths;
        int nstrengths;
};

/**
 * struct nand_ecc_caps - capability of ECC engine
 * @stepinfos: array of ECC step information
 * @nstepinfos: number of ECC step information
 * @calc_ecc_bytes: driver's hook to calculate ECC bytes per step
 */
struct nand_ecc_caps {
        const struct nand_ecc_step_info *stepinfos;
        int nstepinfos;
        int (*calc_ecc_bytes)(int step_size, int strength);
};

/* a shorthand to generate struct nand_ecc_caps with only one ECC stepsize */
#define NAND_ECC_CAPS_SINGLE(__name, __calc, __step, ...)       \
static const int __name##_strengths[] = { __VA_ARGS__ };        \
static const struct nand_ecc_step_info __name##_stepinfo = {    \
        .stepsize = __step,                                     \
        .strengths = __name##_strengths,                        \
        .nstrengths = ARRAY_SIZE(__name##_strengths),           \
};                                                              \
static const struct nand_ecc_caps __name = {                    \
        .stepinfos = &__name##_stepinfo,                        \
        .nstepinfos = 1,                                        \
        .calc_ecc_bytes = __calc,                               \
}

/**
 * struct nand_ecc_ctrl - Control structure for ECC
 * @mode:       ECC mode
 * @algo:       ECC algorithm
 * @steps:      number of ECC steps per page
 * @size:       data bytes per ECC step
 * @bytes:      ECC bytes per step
 * @strength:   max number of correctible bits per ECC step
 * @total:      total number of ECC bytes per page
 * @prepad:     padding information for syndrome based ECC generators
 * @postpad:    padding information for syndrome based ECC generators
 * @options:    ECC specific options (see NAND_ECC_XXX flags defined above)
 * @priv:       pointer to private ECC control data
 * @calc_buf:   buffer for calculated ECC, size is oobsize.
 * @code_buf:   buffer for ECC read from flash, size is oobsize.
 * @hwctl:      function to control hardware ECC generator. Must only
 *              be provided if an hardware ECC is available
 * @calculate:  function for ECC calculation or readback from ECC hardware
 * @correct:    function for ECC correction, matching to ECC generator (sw/hw).
 *              Should return a positive number representing the number of
 *              corrected bitflips, -EBADMSG if the number of bitflips exceed
 *              ECC strength, or any other error code if the error is not
 *              directly related to correction.
 *              If -EBADMSG is returned the input buffers should be left
 *              untouched.
 * @read_page_raw:      function to read a raw page without ECC. This function
 *                      should hide the specific layout used by the ECC
 *                      controller and always return contiguous in-band and
 *                      out-of-band data even if they're not stored
 *                      contiguously on the NAND chip (e.g.
 *                      NAND_ECC_HW_SYNDROME interleaves in-band and
 *                      out-of-band data).
 * @write_page_raw:     function to write a raw page without ECC. This function
 *                      should hide the specific layout used by the ECC
 *                      controller and consider the passed data as contiguous
 *                      in-band and out-of-band data. ECC controller is
 *                      responsible for doing the appropriate transformations
 *                      to adapt to its specific layout (e.g.
 *                      NAND_ECC_HW_SYNDROME interleaves in-band and
 *                      out-of-band data).
 * @read_page:  function to read a page according to the ECC generator
 *              requirements; returns maximum number of bitflips corrected in
 *              any single ECC step, -EIO hw error
 * @read_subpage:       function to read parts of the page covered by ECC;
 *                      returns same as read_page()
 * @write_subpage:      function to write parts of the page covered by ECC.
 * @write_page: function to write a page according to the ECC generator
 *              requirements.
 * @write_oob_raw:      function to write chip OOB data without ECC
 * @read_oob_raw:       function to read chip OOB data without ECC
 * @read_oob:   function to read chip OOB data
 * @write_oob:  function to write chip OOB data
 */
struct nand_ecc_ctrl {
        nand_ecc_modes_t mode;
        enum nand_ecc_algo algo;
        int steps;
        int size;
        int bytes;
        int total;
        int strength;
        int prepad;
        int postpad;
        unsigned int options;
        void *priv;
        u8 *calc_buf;
        u8 *code_buf;
        void (*hwctl)(struct nand_chip *chip, int mode);
        int (*calculate)(struct nand_chip *chip, const uint8_t *dat,
                         uint8_t *ecc_code);
        int (*correct)(struct nand_chip *chip, uint8_t *dat, uint8_t *read_ecc,
                       uint8_t *calc_ecc);
        int (*read_page_raw)(struct nand_chip *chip, uint8_t *buf,
                             int oob_required, int page);
        int (*write_page_raw)(struct nand_chip *chip, const uint8_t *buf,
                              int oob_required, int page);
        int (*read_page)(struct nand_chip *chip, uint8_t *buf,
                         int oob_required, int page);
        int (*read_subpage)(struct nand_chip *chip, uint32_t offs,
                            uint32_t len, uint8_t *buf, int page);
        int (*write_subpage)(struct nand_chip *chip, uint32_t offset,
                             uint32_t data_len, const uint8_t *data_buf,
                             int oob_required, int page);
        int (*write_page)(struct nand_chip *chip, const uint8_t *buf,
                          int oob_required, int page);
        int (*write_oob_raw)(struct nand_chip *chip, int page);
        int (*read_oob_raw)(struct nand_chip *chip, int page);
        int (*read_oob)(struct nand_chip *chip, int page);
        int (*write_oob)(struct nand_chip *chip, int page);
};

/**
 * struct nand_sdr_timings - SDR NAND chip timings
 *
 * This struct defines the timing requirements of a SDR NAND chip.
 * These information can be found in every NAND datasheets and the timings
 * meaning are described in the ONFI specifications:
 * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing
 * Parameters)
 *
 * All these timings are expressed in picoseconds.
 *
 * @tBERS_max: Block erase time
 * @tCCS_min: Change column setup time
 * @tPROG_max: Page program time
 * @tR_max: Page read time
 * @tALH_min: ALE hold time
 * @tADL_min: ALE to data loading time
 * @tALS_min: ALE setup time
 * @tAR_min: ALE to RE# delay
 * @tCEA_max: CE# access time
 * @tCEH_min: CE# high hold time
 * @tCH_min:  CE# hold time
 * @tCHZ_max: CE# high to output hi-Z
 * @tCLH_min: CLE hold time
 * @tCLR_min: CLE to RE# delay
 * @tCLS_min: CLE setup time
 * @tCOH_min: CE# high to output hold
 * @tCS_min: CE# setup time
 * @tDH_min: Data hold time
 * @tDS_min: Data setup time
 * @tFEAT_max: Busy time for Set Features and Get Features
 * @tIR_min: Output hi-Z to RE# low
 * @tITC_max: Interface and Timing Mode Change time
 * @tRC_min: RE# cycle time
 * @tREA_max: RE# access time
 * @tREH_min: RE# high hold time
 * @tRHOH_min: RE# high to output hold
 * @tRHW_min: RE# high to WE# low
 * @tRHZ_max: RE# high to output hi-Z
 * @tRLOH_min: RE# low to output hold
 * @tRP_min: RE# pulse width
 * @tRR_min: Ready to RE# low (data only)
 * @tRST_max: Device reset time, measured from the falling edge of R/B# to the
 *            rising edge of R/B#.
 * @tWB_max: WE# high to SR[6] low
 * @tWC_min: WE# cycle time
 * @tWH_min: WE# high hold time
 * @tWHR_min: WE# high to RE# low
 * @tWP_min: WE# pulse width
 * @tWW_min: WP# transition to WE# low
 */
struct nand_sdr_timings {
        u64 tBERS_max;
        u32 tCCS_min;
        u64 tPROG_max;
        u64 tR_max;
        u32 tALH_min;
        u32 tADL_min;
        u32 tALS_min;
        u32 tAR_min;
        u32 tCEA_max;
        u32 tCEH_min;
        u32 tCH_min;
        u32 tCHZ_max;
        u32 tCLH_min;
        u32 tCLR_min;
        u32 tCLS_min;
        u32 tCOH_min;
        u32 tCS_min;
        u32 tDH_min;
        u32 tDS_min;
        u32 tFEAT_max;
        u32 tIR_min;
        u32 tITC_max;
        u32 tRC_min;
        u32 tREA_max;
        u32 tREH_min;
        u32 tRHOH_min;
        u32 tRHW_min;
        u32 tRHZ_max;
        u32 tRLOH_min;
        u32 tRP_min;
        u32 tRR_min;
        u64 tRST_max;
        u32 tWB_max;
        u32 tWC_min;
        u32 tWH_min;
        u32 tWHR_min;
        u32 tWP_min;
        u32 tWW_min;
};

/**
 * enum nand_data_interface_type - NAND interface timing type
 * @NAND_SDR_IFACE:     Single Data Rate interface
 */
enum nand_data_interface_type {
        NAND_SDR_IFACE,
};

/**
 * struct nand_data_interface - NAND interface timing
 * @type:        type of the timing
 * @timings:     The timing, type according to @type
 * @timings.sdr: Use it when @type is %NAND_SDR_IFACE.
 */
struct nand_data_interface {
        enum nand_data_interface_type type;
        union {
                struct nand_sdr_timings sdr;
        } timings;
};

/**
 * nand_get_sdr_timings - get SDR timing from data interface
 * @conf:       The data interface
 */
static inline const struct nand_sdr_timings *
nand_get_sdr_timings(const struct nand_data_interface *conf)
{
        if (conf->type != NAND_SDR_IFACE)
                return ERR_PTR(-EINVAL);

        return &conf->timings.sdr;
}

/**
 * struct nand_op_cmd_instr - Definition of a command instruction
 * @opcode: the command to issue in one cycle
 */
struct nand_op_cmd_instr {
        u8 opcode;
};

/**
 * struct nand_op_addr_instr - Definition of an address instruction
 * @naddrs: length of the @addrs array
 * @addrs: array containing the address cycles to issue
 */
struct nand_op_addr_instr {
        unsigned int naddrs;
        const u8 *addrs;
};

/**
 * struct nand_op_data_instr - Definition of a data instruction
 * @len: number of data bytes to move
 * @buf: buffer to fill
 * @buf.in: buffer to fill when reading from the NAND chip
 * @buf.out: buffer to read from when writing to the NAND chip
 * @force_8bit: force 8-bit access
 *
 * Please note that "in" and "out" are inverted from the ONFI specification
 * and are from the controller perspective, so a "in" is a read from the NAND
 * chip while a "out" is a write to the NAND chip.
 */
struct nand_op_data_instr {
        unsigned int len;
        union {
                void *in;
                const void *out;
        } buf;
        bool force_8bit;
};

/**
 * struct nand_op_waitrdy_instr - Definition of a wait ready instruction
 * @timeout_ms: maximum delay while waiting for the ready/busy pin in ms
 */
struct nand_op_waitrdy_instr {
        unsigned int timeout_ms;
};

/**
 * enum nand_op_instr_type - Definition of all instruction types
 * @NAND_OP_CMD_INSTR: command instruction
 * @NAND_OP_ADDR_INSTR: address instruction
 * @NAND_OP_DATA_IN_INSTR: data in instruction
 * @NAND_OP_DATA_OUT_INSTR: data out instruction
 * @NAND_OP_WAITRDY_INSTR: wait ready instruction
 */
enum nand_op_instr_type {
        NAND_OP_CMD_INSTR,
        NAND_OP_ADDR_INSTR,
        NAND_OP_DATA_IN_INSTR,
        NAND_OP_DATA_OUT_INSTR,
        NAND_OP_WAITRDY_INSTR,
};

/**
 * struct nand_op_instr - Instruction object
 * @type: the instruction type
 * @ctx:  extra data associated to the instruction. You'll have to use the
 *        appropriate element depending on @type
 * @ctx.cmd: use it if @type is %NAND_OP_CMD_INSTR
 * @ctx.addr: use it if @type is %NAND_OP_ADDR_INSTR
 * @ctx.data: use it if @type is %NAND_OP_DATA_IN_INSTR
 *            or %NAND_OP_DATA_OUT_INSTR
 * @ctx.waitrdy: use it if @type is %NAND_OP_WAITRDY_INSTR
 * @delay_ns: delay the controller should apply after the instruction has been
 *            issued on the bus. Most modern controllers have internal timings
 *            control logic, and in this case, the controller driver can ignore
 *            this field.
 */
struct nand_op_instr {
        enum nand_op_instr_type type;
        union {
                struct nand_op_cmd_instr cmd;
                struct nand_op_addr_instr addr;
                struct nand_op_data_instr data;
                struct nand_op_waitrdy_instr waitrdy;
        } ctx;
        unsigned int delay_ns;
};

/*
 * Special handling must be done for the WAITRDY timeout parameter as it usually
 * is either tPROG (after a prog), tR (before a read), tRST (during a reset) or
 * tBERS (during an erase) which all of them are u64 values that cannot be
 * divided by usual kernel macros and must be handled with the special
 * DIV_ROUND_UP_ULL() macro.
 *
 * Cast to type of dividend is needed here to guarantee that the result won't
 * be an unsigned long long when the dividend is an unsigned long (or smaller),
 * which is what the compiler does when it sees ternary operator with 2
 * different return types (picks the largest type to make sure there's no
 * loss).
 */
#define __DIVIDE(dividend, divisor) ({                                          \
        (__typeof__(dividend))(sizeof(dividend) <= sizeof(unsigned long) ?      \
                               DIV_ROUND_UP(dividend, divisor) :                \
                               DIV_ROUND_UP_ULL(dividend, divisor));            \
        })
#define PSEC_TO_NSEC(x) __DIVIDE(x, 1000)
#define PSEC_TO_MSEC(x) __DIVIDE(x, 1000000000)

#define NAND_OP_CMD(id, ns)                                             \
        {                                                               \
                .type = NAND_OP_CMD_INSTR,                              \
                .ctx.cmd.opcode = id,                                   \
                .delay_ns = ns,                                         \
        }

#define NAND_OP_ADDR(ncycles, cycles, ns)                               \
        {                                                               \
                .type = NAND_OP_ADDR_INSTR,                             \
                .ctx.addr = {                                           \
                        .naddrs = ncycles,                              \
                        .addrs = cycles,                                \
                },                                                      \
                .delay_ns = ns,                                         \
        }

#define NAND_OP_DATA_IN(l, b, ns)                                       \
        {                                                               \
                .type = NAND_OP_DATA_IN_INSTR,                          \
                .ctx.data = {                                           \
                        .len = l,                                       \
                        .buf.in = b,                                    \
                        .force_8bit = false,                            \
                },                                                      \
                .delay_ns = ns,                                         \
        }

#define NAND_OP_DATA_OUT(l, b, ns)                                      \
        {                                                               \
                .type = NAND_OP_DATA_OUT_INSTR,                         \
                .ctx.data = {                                           \
                        .len = l,                                       \
                        .buf.out = b,                                   \
                        .force_8bit = false,                            \
                },                                                      \
                .delay_ns = ns,                                         \
        }

#define NAND_OP_8BIT_DATA_IN(l, b, ns)                                  \
        {                                                               \
                .type = NAND_OP_DATA_IN_INSTR,                          \
                .ctx.data = {                                           \
                        .len = l,                                       \
                        .buf.in = b,                                    \
                        .force_8bit = true,                             \
                },                                                      \
                .delay_ns = ns,                                         \
        }

#define NAND_OP_8BIT_DATA_OUT(l, b, ns)                                 \
        {                                                               \
                .type = NAND_OP_DATA_OUT_INSTR,                         \
                .ctx.data = {                                           \
                        .len = l,                                       \
                        .buf.out = b,                                   \
                        .force_8bit = true,                             \
                },                                                      \
                .delay_ns = ns,                                         \
        }

#define NAND_OP_WAIT_RDY(tout_ms, ns)                                   \
        {                                                               \
                .type = NAND_OP_WAITRDY_INSTR,                          \
                .ctx.waitrdy.timeout_ms = tout_ms,                      \
                .delay_ns = ns,                                         \
        }

/**
 * struct nand_subop - a sub operation
 * @instrs: array of instructions
 * @ninstrs: length of the @instrs array
 * @first_instr_start_off: offset to start from for the first instruction
 *                         of the sub-operation
 * @last_instr_end_off: offset to end at (excluded) for the last instruction
 *                      of the sub-operation
 *
 * Both @first_instr_start_off and @last_instr_end_off only apply to data or
 * address instructions.
 *
 * When an operation cannot be handled as is by the NAND controller, it will
 * be split by the parser into sub-operations which will be passed to the
 * controller driver.
 */
struct nand_subop {
        const struct nand_op_instr *instrs;
        unsigned int ninstrs;
        unsigned int first_instr_start_off;
        unsigned int last_instr_end_off;
};

unsigned int nand_subop_get_addr_start_off(const struct nand_subop *subop,
                                           unsigned int op_id);
unsigned int nand_subop_get_num_addr_cyc(const struct nand_subop *subop,
                                         unsigned int op_id);
unsigned int nand_subop_get_data_start_off(const struct nand_subop *subop,
                                           unsigned int op_id);
unsigned int nand_subop_get_data_len(const struct nand_subop *subop,
                                     unsigned int op_id);

/**
 * struct nand_op_parser_addr_constraints - Constraints for address instructions
 * @maxcycles: maximum number of address cycles the controller can issue in a
 *             single step
 */
struct nand_op_parser_addr_constraints {
        unsigned int maxcycles;
};

/**
 * struct nand_op_parser_data_constraints - Constraints for data instructions
 * @maxlen: maximum data length that the controller can handle in a single step
 */
struct nand_op_parser_data_constraints {
        unsigned int maxlen;
};

/**
 * struct nand_op_parser_pattern_elem - One element of a pattern
 * @type: the instructuction type
 * @optional: whether this element of the pattern is optional or mandatory
 * @ctx: address or data constraint
 * @ctx.addr: address constraint (number of cycles)
 * @ctx.data: data constraint (data length)
 */
struct nand_op_parser_pattern_elem {
        enum nand_op_instr_type type;
        bool optional;
        union {
                struct nand_op_parser_addr_constraints addr;
                struct nand_op_parser_data_constraints data;
        } ctx;
};

#define NAND_OP_PARSER_PAT_CMD_ELEM(_opt)                       \
        {                                                       \
                .type = NAND_OP_CMD_INSTR,                      \
                .optional = _opt,                               \
        }

#define NAND_OP_PARSER_PAT_ADDR_ELEM(_opt, _maxcycles)          \
        {                                                       \
                .type = NAND_OP_ADDR_INSTR,                     \
                .optional = _opt,                               \
                .ctx.addr.maxcycles = _maxcycles,               \
        }

#define NAND_OP_PARSER_PAT_DATA_IN_ELEM(_opt, _maxlen)          \
        {                                                       \
                .type = NAND_OP_DATA_IN_INSTR,                  \
                .optional = _opt,                               \
                .ctx.data.maxlen = _maxlen,                     \
        }

#define NAND_OP_PARSER_PAT_DATA_OUT_ELEM(_opt, _maxlen)         \
        {                                                       \
                .type = NAND_OP_DATA_OUT_INSTR,                 \
                .optional = _opt,                               \
                .ctx.data.maxlen = _maxlen,                     \
        }

#define NAND_OP_PARSER_PAT_WAITRDY_ELEM(_opt)                   \
        {                                                       \
                .type = NAND_OP_WAITRDY_INSTR,                  \
                .optional = _opt,                               \
        }

/**
 * struct nand_op_parser_pattern - NAND sub-operation pattern descriptor
 * @elems: array of pattern elements
 * @nelems: number of pattern elements in @elems array
 * @exec: the function that will issue a sub-operation
 *
 * A pattern is a list of elements, each element reprensenting one instruction
 * with its constraints. The pattern itself is used by the core to match NAND
 * chip operation with NAND controller operations.
 * Once a match between a NAND controller operation pattern and a NAND chip
 * operation (or a sub-set of a NAND operation) is found, the pattern ->exec()
 * hook is called so that the controller driver can issue the operation on the
 * bus.
 *
 * Controller drivers should declare as many patterns as they support and pass
 * this list of patterns (created with the help of the following macro) to
 * the nand_op_parser_exec_op() helper.
 */
struct nand_op_parser_pattern {
        const struct nand_op_parser_pattern_elem *elems;
        unsigned int nelems;
        int (*exec)(struct nand_chip *chip, const struct nand_subop *subop);
};

#define NAND_OP_PARSER_PATTERN(_exec, ...)                                                      \
        {                                                                                       \
                .exec = _exec,                                                                  \
                .elems = (const struct nand_op_parser_pattern_elem[]) { __VA_ARGS__ },          \
                .nelems = sizeof((struct nand_op_parser_pattern_elem[]) { __VA_ARGS__ }) /      \
                          sizeof(struct nand_op_parser_pattern_elem),                           \
        }

/**
 * struct nand_op_parser - NAND controller operation parser descriptor
 * @patterns: array of supported patterns
 * @npatterns: length of the @patterns array
 *
 * The parser descriptor is just an array of supported patterns which will be
 * iterated by nand_op_parser_exec_op() everytime it tries to execute an
 * NAND operation (or tries to determine if a specific operation is supported).
 *
 * It is worth mentioning that patterns will be tested in their declaration
 * order, and the first match will be taken, so it's important to order patterns
 * appropriately so that simple/inefficient patterns are placed at the end of
 * the list. Usually, this is where you put single instruction patterns.
 */
struct nand_op_parser {
        const struct nand_op_parser_pattern *patterns;
        unsigned int npatterns;
};

#define NAND_OP_PARSER(...)                                                                     \
        {                                                                                       \
                .patterns = (const struct nand_op_parser_pattern[]) { __VA_ARGS__ },            \
                .npatterns = sizeof((struct nand_op_parser_pattern[]) { __VA_ARGS__ }) /        \
                             sizeof(struct nand_op_parser_pattern),                             \
        }

/**
 * struct nand_operation - NAND operation descriptor
 * @cs: the CS line to select for this NAND operation
 * @instrs: array of instructions to execute
 * @ninstrs: length of the @instrs array
 *
 * The actual operation structure that will be passed to chip->exec_op().
 */
struct nand_operation {
        unsigned int cs;
        const struct nand_op_instr *instrs;
        unsigned int ninstrs;
};

#define NAND_OPERATION(_cs, _instrs)                            \
        {                                                       \
                .cs = _cs,                                      \
                .instrs = _instrs,                              \
                .ninstrs = ARRAY_SIZE(_instrs),                 \
        }

int nand_op_parser_exec_op(struct nand_chip *chip,
                           const struct nand_op_parser *parser,
                           const struct nand_operation *op, bool check_only);

static inline void nand_op_trace(const char *prefix,
                                 const struct nand_op_instr *instr)
{
#if IS_ENABLED(CONFIG_DYNAMIC_DEBUG) || defined(DEBUG)
        switch (instr->type) {
        case NAND_OP_CMD_INSTR:
                pr_debug("%sCMD      [0x%02x]\n", prefix,
                         instr->ctx.cmd.opcode);
                break;
        case NAND_OP_ADDR_INSTR:
                pr_debug("%sADDR     [%d cyc: %*ph]\n", prefix,
                         instr->ctx.addr.naddrs,
                         instr->ctx.addr.naddrs < 64 ?
                         instr->ctx.addr.naddrs : 64,
                         instr->ctx.addr.addrs);
                break;
        case NAND_OP_DATA_IN_INSTR:
                pr_debug("%sDATA_IN  [%d B%s]\n", prefix,
                         instr->ctx.data.len,
                         instr->ctx.data.force_8bit ?
                         ", force 8-bit" : "");
                break;
        case NAND_OP_DATA_OUT_INSTR:
                pr_debug("%sDATA_OUT [%d B%s]\n", prefix,
                         instr->ctx.data.len,
                         instr->ctx.data.force_8bit ?
                         ", force 8-bit" : "");
                break;
        case NAND_OP_WAITRDY_INSTR:
                pr_debug("%sWAITRDY  [max %d ms]\n", prefix,
                         instr->ctx.waitrdy.timeout_ms);
                break;
        }
#endif
}

/**
 * struct nand_controller_ops - Controller operations
 *
 * @attach_chip: this method is called after the NAND detection phase after
 *               flash ID and MTD fields such as erase size, page size and OOB
 *               size have been set up. ECC requirements are available if
 *               provided by the NAND chip or device tree. Typically used to
 *               choose the appropriate ECC configuration and allocate
 *               associated resources.
 *               This hook is optional.
 * @detach_chip: free all resources allocated/claimed in
 *               nand_controller_ops->attach_chip().
 *               This hook is optional.
 * @exec_op:     controller specific method to execute NAND operations.
 *               This method replaces chip->legacy.cmdfunc(),
 *               chip->legacy.{read,write}_{buf,byte,word}(),
 *               chip->legacy.dev_ready() and chip->legacy.waifunc().
 * @setup_data_interface: setup the data interface and timing. If
 *                        chipnr is set to %NAND_DATA_IFACE_CHECK_ONLY this
 *                        means the configuration should not be applied but
 *                        only checked.
 *                        This hook is optional.
 */
struct nand_controller_ops {
        int (*attach_chip)(struct nand_chip *chip);
        void (*detach_chip)(struct nand_chip *chip);
        int (*exec_op)(struct nand_chip *chip,
                       const struct nand_operation *op,
                       bool check_only);
        int (*setup_data_interface)(struct nand_chip *chip, int chipnr,
                                    const struct nand_data_interface *conf);
};

/**
 * struct nand_controller - Structure used to describe a NAND controller
 *
 * @lock:               lock used to serialize accesses to the NAND controller
 * @ops:                NAND controller operations.
 */
struct nand_controller {
        struct mutex lock;
        const struct nand_controller_ops *ops;
};

static inline void nand_controller_init(struct nand_controller *nfc)
{
        mutex_init(&nfc->lock);
}

/**
 * struct nand_legacy - NAND chip legacy fields/hooks
 * @IO_ADDR_R: address to read the 8 I/O lines of the flash device
 * @IO_ADDR_W: address to write the 8 I/O lines of the flash device
 * @select_chip: select/deselect a specific target/die
 * @read_byte: read one byte from the chip
 * @write_byte: write a single byte to the chip on the low 8 I/O lines
 * @write_buf: write data from the buffer to the chip
 * @read_buf: read data from the chip into the buffer
 * @cmd_ctrl: hardware specific function for controlling ALE/CLE/nCE. Also used
 *            to write command and address
 * @cmdfunc: hardware specific function for writing commands to the chip.
 * @dev_ready: hardware specific function for accessing device ready/busy line.
 *             If set to NULL no access to ready/busy is available and the
 *             ready/busy information is read from the chip status register.
 * @waitfunc: hardware specific function for wait on ready.
 * @block_bad: check if a block is bad, using OOB markers
 * @block_markbad: mark a block bad
 * @set_features: set the NAND chip features
 * @get_features: get the NAND chip features
 * @chip_delay: chip dependent delay for transferring data from array to read
 *              regs (tR).
 * @dummy_controller: dummy controller implementation for drivers that can
 *                    only control a single chip
 *
 * If you look at this structure you're already wrong. These fields/hooks are
 * all deprecated.
 */
struct nand_legacy {
        void __iomem *IO_ADDR_R;
        void __iomem *IO_ADDR_W;
        void (*select_chip)(struct nand_chip *chip, int cs);
        u8 (*read_byte)(struct nand_chip *chip);
        void (*write_byte)(struct nand_chip *chip, u8 byte);
        void (*write_buf)(struct nand_chip *chip, const u8 *buf, int len);
        void (*read_buf)(struct nand_chip *chip, u8 *buf, int len);
        void (*cmd_ctrl)(struct nand_chip *chip, int dat, unsigned int ctrl);
        void (*cmdfunc)(struct nand_chip *chip, unsigned command, int column,
                        int page_addr);
        int (*dev_ready)(struct nand_chip *chip);
        int (*waitfunc)(struct nand_chip *chip);
        int (*block_bad)(struct nand_chip *chip, loff_t ofs);
        int (*block_markbad)(struct nand_chip *chip, loff_t ofs);
        int (*set_features)(struct nand_chip *chip, int feature_addr,
                            u8 *subfeature_para);
        int (*get_features)(struct nand_chip *chip, int feature_addr,
                            u8 *subfeature_para);
        int chip_delay;
        struct nand_controller dummy_controller;
};

/**
 * struct nand_chip - NAND Private Flash Chip Data
 * @base:               Inherit from the generic NAND device
 * @legacy:             All legacy fields/hooks. If you develop a new driver,
 *                      don't even try to use any of these fields/hooks, and if
 *                      you're modifying an existing driver that is using those
 *                      fields/hooks, you should consider reworking the driver
 *                      avoid using them.
 * @setup_read_retry:   [FLASHSPECIFIC] flash (vendor) specific function for
 *                      setting the read-retry mode. Mostly needed for MLC NAND.
 * @ecc:                [BOARDSPECIFIC] ECC control structure
 * @buf_align:          minimum buffer alignment required by a platform
 * @oob_poi:            "poison value buffer," used for laying out OOB data
 *                      before writing
 * @page_shift:         [INTERN] number of address bits in a page (column
 *                      address bits).
 * @phys_erase_shift:   [INTERN] number of address bits in a physical eraseblock
 * @bbt_erase_shift:    [INTERN] number of address bits in a bbt entry
 * @chip_shift:         [INTERN] number of address bits in one chip
 * @options:            [BOARDSPECIFIC] various chip options. They can partly
 *                      be set to inform nand_scan about special functionality.
 *                      See the defines for further explanation.
 * @bbt_options:        [INTERN] bad block specific options. All options used
 *                      here must come from bbm.h. By default, these options
 *                      will be copied to the appropriate nand_bbt_descr's.
 * @badblockpos:        [INTERN] position of the bad block marker in the oob
 *                      area.
 * @badblockbits:       [INTERN] minimum number of set bits in a good block's
 *                      bad block marker position; i.e., BBM == 11110111b is
 *                      not bad when badblockbits == 7
 * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is
 *                            set to the actually used ONFI mode if the chip is
 *                            ONFI compliant or deduced from the datasheet if
 *                            the NAND chip is not ONFI compliant.
 * @pagemask:           [INTERN] page number mask = number of (pages / chip) - 1
 * @data_buf:           [INTERN] buffer for data, size is (page size + oobsize).
 * @pagecache:          Structure containing page cache related fields
 * @pagecache.bitflips: Number of bitflips of the cached page
 * @pagecache.page:     Page number currently in the cache. -1 means no page is
 *                      currently cached
 * @subpagesize:        [INTERN] holds the subpagesize
 * @id:                 [INTERN] holds NAND ID
 * @parameters:         [INTERN] holds generic parameters under an easily
 *                      readable form.
 * @data_interface:     [INTERN] NAND interface timing information
 * @cur_cs:             currently selected target. -1 means no target selected,
 *                      otherwise we should always have cur_cs >= 0 &&
 *                      cur_cs < nanddev_ntargets(). NAND Controller drivers
 *                      should not modify this value, but they're allowed to
 *                      read it.
 * @read_retries:       [INTERN] the number of read retry modes supported
 * @lock:               lock protecting the suspended field. Also used to
 *                      serialize accesses to the NAND device.
 * @suspended:          set to 1 when the device is suspended, 0 when it's not.
 * @bbt:                [INTERN] bad block table pointer
 * @bbt_td:             [REPLACEABLE] bad block table descriptor for flash
 *                      lookup.
 * @bbt_md:             [REPLACEABLE] bad block table mirror descriptor
 * @badblock_pattern:   [REPLACEABLE] bad block scan pattern used for initial
 *                      bad block scan.
 * @controller:         [REPLACEABLE] a pointer to a hardware controller
 *                      structure which is shared among multiple independent
 *                      devices.
 * @priv:               [OPTIONAL] pointer to private chip data
 * @manufacturer:       [INTERN] Contains manufacturer information
 * @manufacturer.desc:  [INTERN] Contains manufacturer's description
 * @manufacturer.priv:  [INTERN] Contains manufacturer private information
 */

struct nand_chip {
        struct nand_device base;

        struct nand_legacy legacy;

        int (*setup_read_retry)(struct nand_chip *chip, int retry_mode);

        unsigned int options;
        unsigned int bbt_options;

        int page_shift;
        int phys_erase_shift;
        int bbt_erase_shift;
        int chip_shift;
        int pagemask;
        u8 *data_buf;

        struct {
                unsigned int bitflips;
                int page;
        } pagecache;

        int subpagesize;
        int onfi_timing_mode_default;
        unsigned int badblockpos;
        int badblockbits;

        struct nand_id id;
        struct nand_parameters parameters;

        struct nand_data_interface data_interface;

        int cur_cs;

        int read_retries;

        struct mutex lock;
        unsigned int suspended : 1;

        uint8_t *oob_poi;
        struct nand_controller *controller;

        struct nand_ecc_ctrl ecc;
        unsigned long buf_align;

        uint8_t *bbt;
        struct nand_bbt_descr *bbt_td;
        struct nand_bbt_descr *bbt_md;

        struct nand_bbt_descr *badblock_pattern;

        void *priv;

        struct {
                const struct nand_manufacturer *desc;
                void *priv;
        } manufacturer;
};

extern const struct mtd_ooblayout_ops nand_ooblayout_sp_ops;
extern const struct mtd_ooblayout_ops nand_ooblayout_lp_ops;

static inline struct nand_chip *mtd_to_nand(struct mtd_info *mtd)
{
        return container_of(mtd, struct nand_chip, base.mtd);
}

static inline struct mtd_info *nand_to_mtd(struct nand_chip *chip)
{
        return &chip->base.mtd;
}

static inline void *nand_get_controller_data(struct nand_chip *chip)
{
        return chip->priv;
}

static inline void nand_set_controller_data(struct nand_chip *chip, void *priv)
{
        chip->priv = priv;
}

static inline void nand_set_manufacturer_data(struct nand_chip *chip,
                                              void *priv)
{
        chip->manufacturer.priv = priv;
}

static inline void *nand_get_manufacturer_data(struct nand_chip *chip)
{
        return chip->manufacturer.priv;
}

static inline void nand_set_flash_node(struct nand_chip *chip,
                                       struct device_node *np)
{
        mtd_set_of_node(nand_to_mtd(chip), np);
}

static inline struct device_node *nand_get_flash_node(struct nand_chip *chip)
{
        return mtd_get_of_node(nand_to_mtd(chip));
}

/*
 * A helper for defining older NAND chips where the second ID byte fully
 * defined the chip, including the geometry (chip size, eraseblock size, page
 * size). All these chips have 512 bytes NAND page size.
 */
#define LEGACY_ID_NAND(nm, devid, chipsz, erasesz, opts)          \
        { .name = (nm), {{ .dev_id = (devid) }}, .pagesize = 512, \
          .chipsize = (chipsz), .erasesize = (erasesz), .options = (opts) }

/*
 * A helper for defining newer chips which report their page size and
 * eraseblock size via the extended ID bytes.
 *
 * The real difference between LEGACY_ID_NAND and EXTENDED_ID_NAND is that with
 * EXTENDED_ID_NAND, manufacturers overloaded the same device ID so that the
 * device ID now only represented a particular total chip size (and voltage,
 * buswidth), and the page size, eraseblock size, and OOB size could vary while
 * using the same device ID.
 */
#define EXTENDED_ID_NAND(nm, devid, chipsz, opts)                      \
        { .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \
          .options = (opts) }

#define NAND_ECC_INFO(_strength, _step) \
                        { .strength_ds = (_strength), .step_ds = (_step) }
#define NAND_ECC_STRENGTH(type)         ((type)->ecc.strength_ds)
#define NAND_ECC_STEP(type)             ((type)->ecc.step_ds)

/**
 * struct nand_flash_dev - NAND Flash Device ID Structure
 * @name: a human-readable name of the NAND chip
 * @dev_id: the device ID (the second byte of the full chip ID array)
 * @mfr_id: manufecturer ID part of the full chip ID array (refers the same
 *          memory address as ``id[0]``)
 * @dev_id: device ID part of the full chip ID array (refers the same memory
 *          address as ``id[1]``)
 * @id: full device ID array
 * @pagesize: size of the NAND page in bytes; if 0, then the real page size (as
 *            well as the eraseblock size) is determined from the extended NAND
 *            chip ID array)
 * @chipsize: total chip size in MiB
 * @erasesize: eraseblock size in bytes (determined from the extended ID if 0)
 * @options: stores various chip bit options
 * @id_len: The valid length of the @id.
 * @oobsize: OOB size
 * @ecc: ECC correctability and step information from the datasheet.
 * @ecc.strength_ds: The ECC correctability from the datasheet, same as the
 *                   @ecc_strength_ds in nand_chip{}.
 * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the
 *               @ecc_step_ds in nand_chip{}, also from the datasheet.
 *               For example, the "4bit ECC for each 512Byte" can be set with
 *               NAND_ECC_INFO(4, 512).
 * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND
 *                            reset. Should be deduced from timings described
 *                            in the datasheet.
 *
 */
struct nand_flash_dev {
        char *name;
        union {
                struct {
                        uint8_t mfr_id;
                        uint8_t dev_id;
                };
                uint8_t id[NAND_MAX_ID_LEN];
        };
        unsigned int pagesize;
        unsigned int chipsize;
        unsigned int erasesize;
        unsigned int options;
        uint16_t id_len;
        uint16_t oobsize;
        struct {
                uint16_t strength_ds;
                uint16_t step_ds;
        } ecc;
        int onfi_timing_mode_default;
};

int nand_create_bbt(struct nand_chip *chip);

/*
 * Check if it is a SLC nand.
 * The !nand_is_slc() can be used to check the MLC/TLC nand chips.
 * We do not distinguish the MLC and TLC now.
 */
static inline bool nand_is_slc(struct nand_chip *chip)
{
        WARN(nanddev_bits_per_cell(&chip->base) == 0,
             "chip->bits_per_cell is used uninitialized\n");
        return nanddev_bits_per_cell(&chip->base) == 1;
}

/**
 * Check if the opcode's address should be sent only on the lower 8 bits
 * @command: opcode to check
 */
static inline int nand_opcode_8bits(unsigned int command)
{
        switch (command) {
        case NAND_CMD_READID:
        case NAND_CMD_PARAM:
        case NAND_CMD_GET_FEATURES:
        case NAND_CMD_SET_FEATURES:
                return 1;
        default:
                break;
        }
        return 0;
}

int nand_check_erased_ecc_chunk(void *data, int datalen,
                                void *ecc, int ecclen,
                                void *extraoob, int extraooblen,
                                int threshold);

int nand_ecc_choose_conf(struct nand_chip *chip,
                         const struct nand_ecc_caps *caps, int oobavail);

/* Default write_oob implementation */
int nand_write_oob_std(struct nand_chip *chip, int page);

/* Default read_oob implementation */
int nand_read_oob_std(struct nand_chip *chip, int page);

/* Stub used by drivers that do not support GET/SET FEATURES operations */
int nand_get_set_features_notsupp(struct nand_chip *chip, int addr,
                                  u8 *subfeature_param);

/* Default read_page_raw implementation */
int nand_read_page_raw(struct nand_chip *chip, uint8_t *buf, int oob_required,
                       int page);

/* Default write_page_raw implementation */
int nand_write_page_raw(struct nand_chip *chip, const uint8_t *buf,
                        int oob_required, int page);

/* Reset and initialize a NAND device */
int nand_reset(struct nand_chip *chip, int chipnr);

/* NAND operation helpers */
int nand_reset_op(struct nand_chip *chip);
int nand_readid_op(struct nand_chip *chip, u8 addr, void *buf,
                   unsigned int len);
int nand_status_op(struct nand_chip *chip, u8 *status);
int nand_erase_op(struct nand_chip *chip, unsigned int eraseblock);
int nand_read_page_op(struct nand_chip *chip, unsigned int page,
                      unsigned int offset_in_page, void *buf, unsigned int len);
int nand_change_read_column_op(struct nand_chip *chip,
                               unsigned int offset_in_page, void *buf,
                               unsigned int len, bool force_8bit);
int nand_read_oob_op(struct nand_chip *chip, unsigned int page,
                     unsigned int offset_in_page, void *buf, unsigned int len);
int nand_prog_page_begin_op(struct nand_chip *chip, unsigned int page,
                            unsigned int offset_in_page, const void *buf,
                            unsigned int len);
int nand_prog_page_end_op(struct nand_chip *chip);
int nand_prog_page_op(struct nand_chip *chip, unsigned int page,
                      unsigned int offset_in_page, const void *buf,
                      unsigned int len);
int nand_change_write_column_op(struct nand_chip *chip,
                                unsigned int offset_in_page, const void *buf,
                                unsigned int len, bool force_8bit);
int nand_read_data_op(struct nand_chip *chip, void *buf, unsigned int len,
                      bool force_8bit);
int nand_write_data_op(struct nand_chip *chip, const void *buf,
                       unsigned int len, bool force_8bit);

/* Scan and identify a NAND device */
int nand_scan_with_ids(struct nand_chip *chip, unsigned int max_chips,
                       struct nand_flash_dev *ids);

static inline int nand_scan(struct nand_chip *chip, unsigned int max_chips)
{
        return nand_scan_with_ids(chip, max_chips, NULL);
}

/* Internal helper for board drivers which need to override command function */
void nand_wait_ready(struct nand_chip *chip);

/*
 * Free resources held by the NAND device, must be called on error after a
 * sucessful nand_scan().
 */
void nand_cleanup(struct nand_chip *chip);
/* Unregister the MTD device and calls nand_cleanup() */
void nand_release(struct nand_chip *chip);

/*
 * External helper for controller drivers that have to implement the WAITRDY
 * instruction and have no physical pin to check it.
 */
int nand_soft_waitrdy(struct nand_chip *chip, unsigned long timeout_ms);
struct gpio_desc;
int nand_gpio_waitrdy(struct nand_chip *chip, struct gpio_desc *gpiod,
                      unsigned long timeout_ms);

/* Select/deselect a NAND target. */
void nand_select_target(struct nand_chip *chip, unsigned int cs);
void nand_deselect_target(struct nand_chip *chip);

/**
 * nand_get_data_buf() - Get the internal page buffer
 * @chip: NAND chip object
 *
 * Returns the pre-allocated page buffer after invalidating the cache. This
 * function should be used by drivers that do not want to allocate their own
 * bounce buffer and still need such a buffer for specific operations (most
 * commonly when reading OOB data only).
 *
 * Be careful to never call this function in the write/write_oob path, because
 * the core may have placed the data to be written out in this buffer.
 *
 * Return: pointer to the page cache buffer
 */
static inline void *nand_get_data_buf(struct nand_chip *chip)
{
        chip->pagecache.page = -1;

        return chip->data_buf;
}

#endif /* __LINUX_MTD_RAWNAND_H */