* better

[mascara-docs.git] / i386 / linux-2.3.21 / Documentation / computone.txt

Computone Intelliport II/Plus Multiport Serial Driver
-----------------------------------------------------

Release Notes For Linux Kernel 2.2 and higher.
These notes are for the drivers which have already been integrated into the
kernel and have been tested on Linux kernels 2.0, 2.2, and 2.3.

Version: 1.2.4
Date: 08/04/99
Author: Andrew Manison <amanison@america.net>
Testing: larryg@computone.com
Support: support@computone.com
Fixes and Updates: Doug McNash <dmcnash@computone.com>
Proc Filesystem and Kernel Integration: Mike Warfield <mhw@wittsend.com>


This file assumes that you are using the Computone drivers which are
integrated into the kernel sources.  For updating the drivers or installing
drivers into kernels which do not already have Computone drivers, please
refer to the instructions in the README.computone file in the driver patch.


1. INTRODUCTION

This driver supports the entire family of Intelliport II/Plus controllers
with the exception of the MicroChannel controllers.  It does not support
products previous to the Intelliport II.

This driver was developed on the v2.0.x Linux tree and has been tested up
to v2.2.9; it will probably not work with earlier v1.X kernels,.


2. QUICK INSTALLATION

Hardware - If you have an ISA card, find a free interrupt and io port. 
                   List those in use with `cat /proc/interrupts` and 
                   `cat /proc/ioports`.  Set the card dip switches to a free 
                   address.  You may need to configure your BIOS to reserve an
                   irq for an ISA card.  PCI and EISA parameters are set
                   automagically.  Insert card into computer with the power off 
                   before or after drivers installation.

        Note the hardware address from the Computone ISA cards installed into
                the system.  These are required for editing ip2.h or editing
                /etc/config.modules, or for specification on the modprobe
                command line.

Software -

Module installation:

a) Obtain driver-kernel patch file
b) Copy to the linux source tree root, Run ip2build (if not patch)
c) Determine free irq/address to use if any (configure BIOS if need be)
d) Run "make config" or "make menuconfig" or "make xconfig"
   Select (m) module for CONFIG_COMPUTONE under character
   devices.  CONFIG_PCI and CONFIG_MODULES also may need to be set.
e) Set address on ISA cards then:
   edit /usr/src/linux/drivers/char/ip2/ip2.h if needed 
        or
   edit /etc/conf.modules (or /etc/modules.conf) if needed (module).
        or both to match this setting.
f) Run "make dep"
g) Run "make modules"
h) Run "make modules_install"
i) Run "/sbin/depmod -a"
j) install driver using `modprobe ip2 <options>` (options listed below)
k) run ip2mkdev (either the script below or the binary version)


Kernel installation:

a) Obtain driver-kernel patch file
b) Copy to the linux source tree root, Run ip2build (if not patch)
c) Determine free irq/address to use if any (configure BIOS if need be)
d) Run "make config" or "make menuconfig" or "make xconfig"
   Select (y) kernel for CONFIG_COMPUTONE under character
   devices.  CONFIG_PCI may need to be set if you have PCI bus.
e) Set address on ISA cards then:
           edit /usr/src/linux/drivers/char/ip2/ip2.h  
f) Run "make dep"
g) Run "make zImage" or whatever target you prefer.
h) mv /usr/src/linux/arch/i386/boot/zImage to /boot.
i) Add new config for this kernel into /etc/lilo.conf, run "lilo"
        or copy to a floppy disk and boot from that floppy disk.
j) Reboot using this kernel
k) run ip2mkdev (either the script below or the binary version)


3. INSTALLATION

Previously, the driver sources were packaged with a set of patch files
to update the character drivers' makefile and configuration file, and other 
kernel source files. A build script (ip2build) was included which applies 
the patches if needed, and build any utilities needed.
What you recieve may be a single patch file in conventional kernel
patch format build script. That form can also be applied by
running patch -p1 < ThePatchFile.  Otherwise run ip2build.
 
The driver can be installed as a module (recommended) or built into the 
kernel. This is selected as for other drivers through the `make config`
command from the root of the Linux source tree. If the driver is built 
into the kernel you will need to edit the file ip2.h to match the boards 
you are installing. See that file for instructions. If the driver is 
installed as a module the configuration can also be specified on the
modprobe command line as follows:

        modprobe ip2 irq=irq1,irq2,irq3,irq4 io=addr1,addr2,addr3,addr4

where irqnum is one of the valid Intelliport II interrupts (3,4,5,7,10,11,
12,15) and addr1-4 are the base addresses for up to four controllers. If 
the irqs are not specified the driver uses the default in ip2/ip2.h (which 
selects polled mode). If no base addresses are specified the defaults in 
ip2.h are used. If you are autoloading the driver module with kerneld or
kmod the base addresses and interrupt number must also be set in ip2/ip2.h
and recompile or just insert and options line in /etc/modules.conf or both. 
The options line is equivalent to the command line and takes precidence over 
what is in ip2.h. 

/etc/modules.conf sample:
        options ip2 io=1,0x328 irq=1,10
        alias char-major-71 ip2
        alias char-major-72 ip2
        alias char-major-73 ip2

equivelant ip2.h:
static ip2config_t ip2config =
{
        {1,10,0,0},
        {
                0x0001,    // Board 0, ttyF0   - ttyF63         /* PCI card */
                0x0328,    // Board 1, ttyF64  - ttyF127        /* ISA card */
                0x0000,    // Board 2, ttyF128 - ttyF191        /* empty */
                0x0000     // Board 3, ttyF192 - ttyF255        /* empty */
        }
};


Note:   Both io and irq should be updated to reflect YOUR system.  An "io"
        address of "1/2" indicates a PCI/EISA card in the board table.  The
        PCI or EISA irq will be assigned automatically.

Specifying an invalid or in-use irq will default the driver into
running in polled mode for that card.  If all irq entries are 0 then
all cards will operate in polled mode.

If you select the driver as part of the kernel run :

        make depend
        make zlilo (or whatever you do to create a bootable kernel)

If you selected a module run :

        make modules && make modules_install

The utility ip2mkdev (see 5 and 7 below) creates all the device nodes
required by the driver.  For a device to be created it must be configured
in the driver and the board must be installed. Only devices corresponding
to real IntelliPort II ports are created. With multiple boards and expansion
boxes this will leave gaps in the sequence of device names. ip2mkdev uses
Linux tty naming conventions: ttyF0 - ttyF255 for normal devices, and
cuf0 - cuf255 for callout devices.


4. USING THE DRIVERS

As noted above, the driver implements the ports in accordance with Linux
conventions, and the devices should be interchangeable with the standard
serial devices. (This is a key point for problem reporting: please make
sure that what you are trying do works on the ttySx/cuax ports first; then 
tell us what went wrong with the ip2 ports!)

Higher speeds can be obtained using the setserial utility which remaps 
38,400 bps (extb) to 57,600 bps, 115,200 bps, or a custom speed. 
Intelliport II installations using the PowerPort expansion module can
use the custom speed setting to select the highest speeds: 153,600 bps,
230,400 bps, 307,200 bps, 460,800bps and 921,600 bps. The base for
custom baud rate configuration is fixed at 921,600 for cards/expantion
modules with ST654's and 115200 for those with Cirrus CD1400's.  This
corresponds to the maximum bit rates those chips are capable.  
For example if the baud base is 921600 and the baud divisor is 18 then
the custom rate is 921600/18 = 51200 bps.  See the setserial man page for
complete details. Of course if stty accepts the higher rates now you can
use that as well as the standard ioctls().


5. ip2mkdev and assorted utilities...

Several utilities, including the source for a binary ip2mkdev utility are
available under .../drivers/char/ip2.  These can be build by changing to
that directory and typing "make" after the kernel has be built.  If you do
not wish to compile the binary utilities, the shell script below can be
cut out and run as "ip2mkdev" to create the necessary device files.  To
use the ip2mkdev script, you must have procfs enabled and the proc file
system mounted on /proc.

6. NOTES

This is a release version of the driver, but it is impossible to test it
in all configurations of Linux. If there is any anomalous behaviour that 
does not match the standard serial port's behaviour please let us know.


7. ip2mkdev shell script

===== Cut Here ===== 
#!/bin/sh -

#       ip2mkdev
#
#       Make or remove devices as needed for Computone Intelliport drivers
#
#       First rule!  If the dev file exists and you need it, don't mess
#       with it.  That prevents us from screwing up open ttys, ownership
#       and permissions on a running system!
#
#       This script will NOT remove devices that no longer exist because
#       their board or interface box has been removed.  If you want to get
#       rid of them, you can manually do an "rm -f /dev/ttyF* /dev/cuaf*"
#       before running this script, which will then recreate all the valid
#       devices
#
#       =mhw=
#       Michael H. Warfield
#       mhw@wittsend.com
#
if test ! -f /proc/tty/drivers
then
        echo "\
Unable to check driver status.
Make sure proc file system is mounted."

        exit 255
fi

if test ! -f /proc/tty/driver/ip2
then
        echo "\
Unable to locate ip2 proc file.
Attempting to load driver"

        if insmod ip2
        then
                if test ! -f /proc/tty/driver/ip2
                then
                        echo "\
Unable to locate ip2 proc file after loading driver.
Driver initialization failure or driver version error.
"
                exit 255
                fi
        else
                echo "Unable to load ip2 driver."
                exit 255
        fi
fi

# Ok...  So we got the driver loaded and we can locate the procfs files.
# Next we need our major numbers.

TTYMAJOR=`sed -e '/^ip2/!d' -e '/\/dev\/tty/!d' -e 's/.*tty.[   ]*\([0-9]*\)[   ]*.*/\1/' < /proc/tty/drivers`
CUAMAJOR=`sed -e '/^ip2/!d' -e '/\/dev\/cu/!d' -e 's/.*cu.[     ]*\([0-9]*\)[   ]*.*/\1/' < /proc/tty/drivers`
BRDMAJOR=`sed -e '/^Driver: /!d' -e 's/.*IMajor=\([0-9]*\)[     ]*.*/\1/' < /proc/tty/driver/ip2`

echo "\
TTYMAJOR = $TTYMAJOR
CUAMAJOR = $CUAMAJOR
BRDMAJOR = $BRDMAJOR
"

# Ok...  Now we should know our major numbers, if appropriate...
# Now we need our boards and start the device loops.

grep '^Board [0-9]:' /proc/tty/driver/ip2 | while read token number type alltherest
do
        # The test for blank "type" will catch the stats lead-in lines
        # if they exist in the file
        if test "$type" = "vacant" -o "$type" = "Vacant" -o "$type" = ""
        then
                continue
        fi

        BOARDNO=`expr "$number" : '\([0-9]\):'`
        PORTS=`expr "$alltherest" : '.*ports=\([0-9]*\)' | tr ',' ' '`
        MINORS=`expr "$alltherest" : '.*minors=\([0-9,]*\)' | tr ',' ' '`

        if test "$BOARDNO" = "" -o "$PORTS" = ""
        then
#       This may be a bug.  We should at least get this much information
                echo "Unable to process board line"
                continue
        fi

        if test "$MINORS" = ""
        then
#       Silently skip this one.  This board seems to have no boxes
                continue
        fi

        echo "board $BOARDNO: $type ports = $PORTS; port numbers = $MINORS"

        if test "$BRDMAJOR" != ""
        then
                BRDMINOR=`expr $BOARDNO \* 4`
                STSMINOR=`expr $BRDMINOR + 1`
                if test ! -c /dev/ip2ipl$BOARDNO ; then
                        mknod /dev/ip2ipl$BOARDNO c $BRDMAJOR $BRDMINOR
                fi
                if test ! -c /dev/ip2stat$BOARDNO ; then
                        mknod /dev/ip2stat$BOARDNO c $BRDMAJOR $STSMINOR
                fi
        fi

        if test "$TTYMAJOR" != ""
        then
                PORTNO=$BOARDBASE

                for PORTNO in $MINORS
                do
                        if test ! -c /dev/ttyF$PORTNO ; then
                                # We got the harware but no device - make it
                                mknod /dev/ttyF$PORTNO c $TTYMAJOR $PORTNO
                        fi      
                done
        fi

        if test "$CUAMAJOR" != ""
        then
                PORTNO=$BOARDBASE

                for PORTNO in $MINORS
                do
                        if test ! -c /dev/cuf$PORTNO ; then
                                # We got the harware but no device - make it
                                mknod /dev/cuf$PORTNO c $CUAMAJOR $PORTNO
                        fi      
                done
        fi
done

exit 0
===== Cut Here =====