Linking blocktest without libc to allow terminal output
[minix3.git] / drivers / dp8390 / wdeth.h
blobd873f8b462b5704a9dceb8f7a0928c768482e9eb
1 /*
2 wdeth.h
4 Created: before Dec 28, 1992 by Philip Homburg
5 */
7 #ifndef WDETH_H
8 #define WDETH_H
10 /* Western Digital Ethercard Plus, or WD8003E card. */
12 #define EPL_REG0 0x0 /* Control(write) and status(read) */
13 #define EPL_REG1 0x1
14 #define EPL_REG2 0x2
15 #define EPL_REG3 0x3
16 #define EPL_REG4 0x4
17 #define EPL_REG5 0x5
18 #define EPL_REG6 0x6
19 #define EPL_REG7 0x7
20 #define EPL_EA0 0x8 /* Most significant eaddr byte */
21 #define EPL_EA1 0x9
22 #define EPL_EA2 0xA
23 #define EPL_EA3 0xB
24 #define EPL_EA4 0xC
25 #define EPL_EA5 0xD /* Least significant eaddr byte */
26 #define EPL_TLB 0xE
27 #define EPL_CHKSUM 0xF /* sum from epl_ea0 upto here is 0xFF */
28 #define EPL_DP8390 0x10 /* NatSemi chip */
30 #define EPL_MSR EPL_REG0 /* memory select register */
31 #define EPL_ICR EPL_REG1 /* interface configuration register */
32 #define EPL_IRR EPL_REG4 /* interrupt request register (IRR) */
33 #define EPL_790_HWR EPL_REG4 /* '790 hardware support register */
34 #define EPL_LAAR EPL_REG5 /* LA address register (write only) */
35 #define EPL_790_ICR EPL_REG6 /* '790 interrupt control register */
36 #define EPL_GP2 EPL_REG7 /* general purpose register 2 */
37 #define EPL_790_B EPL_EA3 /* '790 memory register */
38 #define EPL_790_GCR EPL_EA5 /* '790 General Control Register */
40 /* Bits in EPL_MSR */
41 #define E_MSR_MEMADDR 0x3F /* Bits SA18-SA13, SA19 implicit 1 */
42 #define E_MSR_MENABLE 0x40 /* Memory Enable */
43 #define E_MSR_RESET 0x80 /* Software Reset */
45 /* Bits in EPL_ICR */
46 #define E_ICR_16BIT 0x01 /* 16 bit bus */
47 #define E_ICR_IR2 0x04 /* bit 2 of encoded IRQ */
48 #define E_ICR_MEMBIT 0x08 /* 583 mem size mask */
50 /* Bits in EPL_IRR */
51 #define E_IRR_IR0 0x20 /* bit 0 of encoded IRQ */
52 #define E_IRR_IR1 0x40 /* bit 1 of encoded IRQ */
53 #define E_IRR_IEN 0x80 /* enable interrupts */
55 /* Bits in EPL_LAAR */
56 #define E_LAAR_A19 0x01 /* address lines for above 1M ram */
57 #define E_LAAR_A20 0x02 /* address lines for above 1M ram */
58 #define E_LAAR_A21 0x04 /* address lines for above 1M ram */
59 #define E_LAAR_A22 0x08 /* address lines for above 1M ram */
60 #define E_LAAR_A23 0x10 /* address lines for above 1M ram */
61 #define E_LAAR_SOFTINT 0x20 /* enable software interrupt */
62 #define E_LAAR_LAN16E 0x40 /* enables 16 bit RAM for LAN */
63 #define E_LAAR_MEM16E 0x80 /* enables 16 bit RAM for host */
65 /* Bits and values in EPL_TLB */
66 #define E_TLB_EB 0x05 /* WD8013EB */
67 #define E_TLB_E 0x27 /* WD8013 Elite */
68 #define E_TLB_SMCE 0x29 /* SMC Elite 16 */
69 #define E_TLB_SMC8216T 0x2A /* SMC 8216 T */
70 #define E_TLB_SMC8216C 0x2B /* SMC 8216 C */
72 #define E_TLB_REV 0x1F /* revision mask */
73 #define E_TLB_SOFT 0x20 /* soft config */
74 #define E_TLB_RAM 0x40 /* extra ram bit */
76 /* Bits in EPL_790_HWR */
77 #define E_790_HWR_SWH 0x80 /* switch register set */
79 /* Bits in EPL_790_ICR */
80 #define E_790_ICR_EIL 0x01 /* enable interrupts */
82 /* Bits in EPL_790_GCR when E_790_HWR_SWH is set in EPL_790_HWR */
83 #define E_790_GCR_IR0 0x04 /* bit 0 of encoded IRQ */
84 #define E_790_GCR_IR1 0x08 /* bit 1 of encoded IRQ */
85 #define E_790_GCR_IR2 0x40 /* bit 2 of encoded IRQ */
87 #define inb_we(dep, reg) (inb(dep->de_base_port+reg))
88 #define outb_we(dep, reg, data) (outb(dep->de_base_port+reg, data))
90 #endif /* WDETH_H */
93 * $PchId: wdeth.h,v 1.6 2003/09/10 19:29:52 philip Exp $