drivers/ata/pata_radisys.c

   1 /*
   2  *    pata_radisys.c - Intel PATA/SATA controllers
   3  *
   4  *      (C) 2006 Red Hat <alan@lxorguk.ukuu.org.uk>
   5  *
   6  *    Some parts based on ata_piix.c by Jeff Garzik and others.
   7  *
   8  *    A PIIX relative, this device has a single ATA channel and no
   9  *    slave timings, SITRE or PPE. In that sense it is a close relative
  10  *    of the original PIIX. It does however support UDMA 33/66 per channel
  11  *    although no other modes/timings. Also lacking is 32bit I/O on the ATA
  12  *    port.
  13  */
  14
  15 #include <linux/kernel.h>
  16 #include <linux/module.h>
  17 #include <linux/pci.h>
  18 #include <linux/init.h>
  19 #include <linux/blkdev.h>
  20 #include <linux/delay.h>
  21 #include <linux/device.h>
  22 #include <scsi/scsi_host.h>
  23 #include <linux/libata.h>
  24 #include <linux/ata.h>
  25
  26 #define DRV_NAME        "pata_radisys"
  27 #define DRV_VERSION     "0.4.4"
  28
  29 /**
  30  *      radisys_set_piomode - Initialize host controller PATA PIO timings
  31  *      @ap: ATA port
  32  *      @adev: Device whose timings we are configuring
  33  *
  34  *      Set PIO mode for device, in host controller PCI config space.
  35  *
  36  *      LOCKING:
  37  *      None (inherited from caller).
  38  */
  39
  40 static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
  41 {
  42         unsigned int pio        = adev->pio_mode - XFER_PIO_0;
  43         struct pci_dev *dev     = to_pci_dev(ap->host->dev);
  44         u16 idetm_data;
  45         int control = 0;
  46
  47         /*
  48          *      See Intel Document 298600-004 for the timing programing rules
  49          *      for PIIX/ICH. Note that the early PIIX does not have the slave
  50          *      timing port at 0x44. The Radisys is a relative of the PIIX
  51          *      but not the same so be careful.
  52          */
  53
  54         static const     /* ISP  RTC */
  55         u8 timings[][2] = { { 0, 0 },   /* Check me */
  56                             { 0, 0 },
  57                             { 1, 1 },
  58                             { 2, 2 },
  59                             { 3, 3 }, };
  60
  61         if (pio > 0)
  62                 control |= 1;   /* TIME1 enable */
  63         if (ata_pio_need_iordy(adev))
  64                 control |= 2;   /* IE IORDY */
  65
  66         pci_read_config_word(dev, 0x40, &idetm_data);
  67
  68         /* Enable IE and TIME as appropriate. Clear the other
  69            drive timing bits */
  70         idetm_data &= 0xCCCC;
  71         idetm_data |= (control << (4 * adev->devno));
  72         idetm_data |= (timings[pio][0] << 12) |
  73                         (timings[pio][1] << 8);
  74         pci_write_config_word(dev, 0x40, idetm_data);
  75
  76         /* Track which port is configured */
  77         ap->private_data = adev;
  78 }
  79
  80 /**
  81  *      radisys_set_dmamode - Initialize host controller PATA DMA timings
  82  *      @ap: Port whose timings we are configuring
  83  *      @adev: Device to program
  84  *
  85  *      Set MWDMA mode for device, in host controller PCI config space.
  86  *
  87  *      LOCKING:
  88  *      None (inherited from caller).
  89  */
  90
  91 static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
  92 {
  93         struct pci_dev *dev     = to_pci_dev(ap->host->dev);
  94         u16 idetm_data;
  95         u8 udma_enable;
  96
  97         static const     /* ISP  RTC */
  98         u8 timings[][2] = { { 0, 0 },
  99                             { 0, 0 },
 100                             { 1, 1 },
 101                             { 2, 2 },
 102                             { 3, 3 }, };
 103
 104         /*
 105          * MWDMA is driven by the PIO timings. We must also enable
 106          * IORDY unconditionally.
 107          */
 108
 109         pci_read_config_word(dev, 0x40, &idetm_data);
 110         pci_read_config_byte(dev, 0x48, &udma_enable);
 111
 112         if (adev->dma_mode < XFER_UDMA_0) {
 113                 unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
 114                 const unsigned int needed_pio[3] = {
 115                         XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
 116                 };
 117                 int pio = needed_pio[mwdma] - XFER_PIO_0;
 118                 int control = 3;        /* IORDY|TIME0 */
 119
 120                 /* If the drive MWDMA is faster than it can do PIO then
 121                    we must force PIO0 for PIO cycles. */
 122
 123                 if (adev->pio_mode < needed_pio[mwdma])
 124                         control = 1;
 125
 126                 /* Mask out the relevant control and timing bits we will load. Also
 127                    clear the other drive TIME register as a precaution */
 128
 129                 idetm_data &= 0xCCCC;
 130                 idetm_data |= control << (4 * adev->devno);
 131                 idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
 132
 133                 udma_enable &= ~(1 << adev->devno);
 134         } else {
 135                 u8 udma_mode;
 136
 137                 /* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */
 138
 139                 pci_read_config_byte(dev, 0x4A, &udma_mode);
 140
 141                 if (adev->xfer_mode == XFER_UDMA_2)
 142                         udma_mode &= ~ (1 << adev->devno);
 143                 else /* UDMA 4 */
 144                         udma_mode |= (1 << adev->devno);
 145
 146                 pci_write_config_byte(dev, 0x4A, udma_mode);
 147
 148                 udma_enable |= (1 << adev->devno);
 149         }
 150         pci_write_config_word(dev, 0x40, idetm_data);
 151         pci_write_config_byte(dev, 0x48, udma_enable);
 152
 153         /* Track which port is configured */
 154         ap->private_data = adev;
 155 }
 156
 157 /**
 158  *      radisys_qc_issue        -       command issue
 159  *      @qc: command pending
 160  *
 161  *      Called when the libata layer is about to issue a command. We wrap
 162  *      this interface so that we can load the correct ATA timings if
 163  *      necessary. Our logic also clears TIME0/TIME1 for the other device so
 164  *      that, even if we get this wrong, cycles to the other device will
 165  *      be made PIO0.
 166  */
 167
 168 static unsigned int radisys_qc_issue(struct ata_queued_cmd *qc)
 169 {
 170         struct ata_port *ap = qc->ap;
 171         struct ata_device *adev = qc->dev;
 172
 173         if (adev != ap->private_data) {
 174                 /* UDMA timing is not shared */
 175                 if (adev->dma_mode < XFER_UDMA_0) {
 176                         if (adev->dma_mode)
 177                                 radisys_set_dmamode(ap, adev);
 178                         else if (adev->pio_mode)
 179                                 radisys_set_piomode(ap, adev);
 180                 }
 181         }
 182         return ata_sff_qc_issue(qc);
 183 }
 184
 185
 186 static struct scsi_host_template radisys_sht = {
 187         ATA_BMDMA_SHT(DRV_NAME),
 188 };
 189
 190 static struct ata_port_operations radisys_pata_ops = {
 191         .inherits               = &ata_bmdma_port_ops,
 192         .qc_issue               = radisys_qc_issue,
 193         .cable_detect           = ata_cable_unknown,
 194         .set_piomode            = radisys_set_piomode,
 195         .set_dmamode            = radisys_set_dmamode,
 196 };
 197
 198
 199 /**
 200  *      radisys_init_one - Register PIIX ATA PCI device with kernel services
 201  *      @pdev: PCI device to register
 202  *      @ent: Entry in radisys_pci_tbl matching with @pdev
 203  *
 204  *      Called from kernel PCI layer.  We probe for combined mode (sigh),
 205  *      and then hand over control to libata, for it to do the rest.
 206  *
 207  *      LOCKING:
 208  *      Inherited from PCI layer (may sleep).
 209  *
 210  *      RETURNS:
 211  *      Zero on success, or -ERRNO value.
 212  */
 213
 214 static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 215 {
 216         static int printed_version;
 217         static const struct ata_port_info info = {
 218                 .flags          = ATA_FLAG_SLAVE_POSS,
 219                 .pio_mask       = ATA_PIO4,
 220                 .mwdma_mask     = ATA_MWDMA12_ONLY,
 221                 .udma_mask      = ATA_UDMA24_ONLY,
 222                 .port_ops       = &radisys_pata_ops,
 223         };
 224         const struct ata_port_info *ppi[] = { &info, NULL };
 225
 226         if (!printed_version++)
 227                 dev_printk(KERN_DEBUG, &pdev->dev,
 228                            "version " DRV_VERSION "\n");
 229
 230         return ata_pci_sff_init_one(pdev, ppi, &radisys_sht, NULL);
 231 }
 232
 233 static const struct pci_device_id radisys_pci_tbl[] = {
 234         { PCI_VDEVICE(RADISYS, 0x8201), },
 235
 236         { }     /* terminate list */
 237 };
 238
 239 static struct pci_driver radisys_pci_driver = {
 240         .name                   = DRV_NAME,
 241         .id_table               = radisys_pci_tbl,
 242         .probe                  = radisys_init_one,
 243         .remove                 = ata_pci_remove_one,
 244 #ifdef CONFIG_PM
 245         .suspend                = ata_pci_device_suspend,
 246         .resume                 = ata_pci_device_resume,
 247 #endif
 248 };
 249
 250 static int __init radisys_init(void)
 251 {
 252         return pci_register_driver(&radisys_pci_driver);
 253 }
 254
 255 static void __exit radisys_exit(void)
 256 {
 257         pci_unregister_driver(&radisys_pci_driver);
 258 }
 259
 260 module_init(radisys_init);
 261 module_exit(radisys_exit);
 262
 263 MODULE_AUTHOR("Alan Cox");
 264 MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
 265 MODULE_LICENSE("GPL");
 266 MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
 267 MODULE_VERSION(DRV_VERSION);
 268