drivers/net/wireless/libertas/host.h

   1 /**
   2   * This file contains definitions of WLAN commands.
   3   */
   4
   5 #ifndef _LBS_HOST_H_
   6 #define _LBS_HOST_H_
   7
   8 /** PUBLIC DEFINITIONS */
   9 #define DEFAULT_AD_HOC_CHANNEL                  6
  10 #define DEFAULT_AD_HOC_CHANNEL_A                36
  11
  12 #define CMD_OPTION_WAITFORRSP                   0x0002
  13
  14 /** Host command IDs */
  15
  16 /* Return command are almost always the same as the host command, but with
  17  * bit 15 set high.  There are a few exceptions, though...
  18  */
  19 #define CMD_RET(cmd)                    (0x8000 | cmd)
  20
  21 /* Return command convention exceptions: */
  22 #define CMD_RET_802_11_ASSOCIATE                0x8012
  23
  24 /* Command codes */
  25 #define CMD_GET_HW_SPEC                         0x0003
  26 #define CMD_EEPROM_UPDATE                       0x0004
  27 #define CMD_802_11_RESET                        0x0005
  28 #define CMD_802_11_SCAN                         0x0006
  29 #define CMD_802_11_GET_LOG                      0x000b
  30 #define CMD_MAC_MULTICAST_ADR                   0x0010
  31 #define CMD_802_11_AUTHENTICATE                 0x0011
  32 #define CMD_802_11_EEPROM_ACCESS                0x0059
  33 #define CMD_802_11_ASSOCIATE                    0x0050
  34 #define CMD_802_11_SET_WEP                      0x0013
  35 #define CMD_802_11_GET_STAT                     0x0014
  36 #define CMD_802_3_GET_STAT                      0x0015
  37 #define CMD_802_11_SNMP_MIB                     0x0016
  38 #define CMD_MAC_REG_MAP                         0x0017
  39 #define CMD_BBP_REG_MAP                         0x0018
  40 #define CMD_MAC_REG_ACCESS                      0x0019
  41 #define CMD_BBP_REG_ACCESS                      0x001a
  42 #define CMD_RF_REG_ACCESS                       0x001b
  43 #define CMD_802_11_RADIO_CONTROL                0x001c
  44 #define CMD_802_11_RF_CHANNEL                   0x001d
  45 #define CMD_802_11_RF_TX_POWER                  0x001e
  46 #define CMD_802_11_RSSI                         0x001f
  47 #define CMD_802_11_RF_ANTENNA                   0x0020
  48 #define CMD_802_11_PS_MODE                      0x0021
  49 #define CMD_802_11_DATA_RATE                    0x0022
  50 #define CMD_RF_REG_MAP                          0x0023
  51 #define CMD_802_11_DEAUTHENTICATE               0x0024
  52 #define CMD_802_11_REASSOCIATE                  0x0025
  53 #define CMD_MAC_CONTROL                         0x0028
  54 #define CMD_802_11_AD_HOC_START                 0x002b
  55 #define CMD_802_11_AD_HOC_JOIN                  0x002c
  56 #define CMD_802_11_QUERY_TKIP_REPLY_CNTRS       0x002e
  57 #define CMD_802_11_ENABLE_RSN                   0x002f
  58 #define CMD_802_11_SET_AFC                      0x003c
  59 #define CMD_802_11_GET_AFC                      0x003d
  60 #define CMD_802_11_DEEP_SLEEP                  0x003e
  61 #define CMD_802_11_AD_HOC_STOP                  0x0040
  62 #define CMD_802_11_HOST_SLEEP_CFG               0x0043
  63 #define CMD_802_11_WAKEUP_CONFIRM               0x0044
  64 #define CMD_802_11_HOST_SLEEP_ACTIVATE          0x0045
  65 #define CMD_802_11_BEACON_STOP                  0x0049
  66 #define CMD_802_11_MAC_ADDRESS                  0x004d
  67 #define CMD_802_11_LED_GPIO_CTRL                0x004e
  68 #define CMD_802_11_EEPROM_ACCESS                0x0059
  69 #define CMD_802_11_BAND_CONFIG                  0x0058
  70 #define CMD_GSPI_BUS_CONFIG                     0x005a
  71 #define CMD_802_11D_DOMAIN_INFO                 0x005b
  72 #define CMD_802_11_KEY_MATERIAL                 0x005e
  73 #define CMD_802_11_SLEEP_PARAMS                 0x0066
  74 #define CMD_802_11_INACTIVITY_TIMEOUT           0x0067
  75 #define CMD_802_11_SLEEP_PERIOD                 0x0068
  76 #define CMD_802_11_TPC_CFG                      0x0072
  77 #define CMD_802_11_PA_CFG                       0x0073
  78 #define CMD_802_11_FW_WAKE_METHOD               0x0074
  79 #define CMD_802_11_SUBSCRIBE_EVENT              0x0075
  80 #define CMD_802_11_RATE_ADAPT_RATESET           0x0076
  81 #define CMD_802_11_TX_RATE_QUERY                0x007f
  82 #define CMD_GET_TSF                             0x0080
  83 #define CMD_BT_ACCESS                           0x0087
  84 #define CMD_FWT_ACCESS                          0x0095
  85 #define CMD_802_11_MONITOR_MODE                 0x0098
  86 #define CMD_MESH_ACCESS                         0x009b
  87 #define CMD_MESH_CONFIG_OLD                     0x00a3
  88 #define CMD_MESH_CONFIG                         0x00ac
  89 #define CMD_SET_BOOT2_VER                       0x00a5
  90 #define CMD_FUNC_INIT                           0x00a9
  91 #define CMD_FUNC_SHUTDOWN                       0x00aa
  92 #define CMD_802_11_BEACON_CTRL                  0x00b0
  93
  94 /* For the IEEE Power Save */
  95 #define CMD_SUBCMD_ENTER_PS             0x0030
  96 #define CMD_SUBCMD_EXIT_PS              0x0031
  97 #define CMD_SUBCMD_SLEEP_CONFIRMED      0x0034
  98 #define CMD_SUBCMD_FULL_POWERDOWN       0x0035
  99 #define CMD_SUBCMD_FULL_POWERUP         0x0036
 100
 101 #define CMD_ENABLE_RSN                  0x0001
 102 #define CMD_DISABLE_RSN                 0x0000
 103
 104 #define CMD_ACT_GET                     0x0000
 105 #define CMD_ACT_SET                     0x0001
 106 #define CMD_ACT_GET_AES                 0x0002
 107 #define CMD_ACT_SET_AES                 0x0003
 108 #define CMD_ACT_REMOVE_AES              0x0004
 109
 110 /* Define action or option for CMD_802_11_SET_WEP */
 111 #define CMD_ACT_ADD                     0x0002
 112 #define CMD_ACT_REMOVE                  0x0004
 113 #define CMD_ACT_USE_DEFAULT             0x0008
 114
 115 #define CMD_TYPE_WEP_40_BIT             0x01
 116 #define CMD_TYPE_WEP_104_BIT            0x02
 117
 118 #define CMD_NUM_OF_WEP_KEYS             4
 119
 120 #define CMD_WEP_KEY_INDEX_MASK          0x3fff
 121
 122 /* Define action or option for CMD_802_11_RESET */
 123 #define CMD_ACT_HALT                    0x0003
 124
 125 /* Define action or option for CMD_802_11_SCAN */
 126 #define CMD_BSS_TYPE_BSS                0x0001
 127 #define CMD_BSS_TYPE_IBSS               0x0002
 128 #define CMD_BSS_TYPE_ANY                0x0003
 129
 130 /* Define action or option for CMD_802_11_SCAN */
 131 #define CMD_SCAN_TYPE_ACTIVE            0x0000
 132 #define CMD_SCAN_TYPE_PASSIVE           0x0001
 133
 134 #define CMD_SCAN_RADIO_TYPE_BG          0
 135
 136 #define CMD_SCAN_PROBE_DELAY_TIME       0
 137
 138 /* Define action or option for CMD_MAC_CONTROL */
 139 #define CMD_ACT_MAC_RX_ON                       0x0001
 140 #define CMD_ACT_MAC_TX_ON                       0x0002
 141 #define CMD_ACT_MAC_LOOPBACK_ON                 0x0004
 142 #define CMD_ACT_MAC_WEP_ENABLE                  0x0008
 143 #define CMD_ACT_MAC_INT_ENABLE                  0x0010
 144 #define CMD_ACT_MAC_MULTICAST_ENABLE            0x0020
 145 #define CMD_ACT_MAC_BROADCAST_ENABLE            0x0040
 146 #define CMD_ACT_MAC_PROMISCUOUS_ENABLE          0x0080
 147 #define CMD_ACT_MAC_ALL_MULTICAST_ENABLE        0x0100
 148 #define CMD_ACT_MAC_STRICT_PROTECTION_ENABLE    0x0400
 149
 150 /* Event flags for CMD_802_11_SUBSCRIBE_EVENT */
 151 #define CMD_SUBSCRIBE_RSSI_LOW          0x0001
 152 #define CMD_SUBSCRIBE_SNR_LOW           0x0002
 153 #define CMD_SUBSCRIBE_FAILCOUNT         0x0004
 154 #define CMD_SUBSCRIBE_BCNMISS           0x0008
 155 #define CMD_SUBSCRIBE_RSSI_HIGH         0x0010
 156 #define CMD_SUBSCRIBE_SNR_HIGH          0x0020
 157
 158 #define RADIO_PREAMBLE_LONG     0x00
 159 #define RADIO_PREAMBLE_SHORT    0x02
 160 #define RADIO_PREAMBLE_AUTO     0x04
 161
 162 /* Define action or option for CMD_802_11_RF_CHANNEL */
 163 #define CMD_OPT_802_11_RF_CHANNEL_GET   0x00
 164 #define CMD_OPT_802_11_RF_CHANNEL_SET   0x01
 165
 166 /* Define action or option for CMD_802_11_DATA_RATE */
 167 #define CMD_ACT_SET_TX_AUTO             0x0000
 168 #define CMD_ACT_SET_TX_FIX_RATE         0x0001
 169 #define CMD_ACT_GET_TX_RATE             0x0002
 170
 171 #define CMD_ACT_SET_RX                  0x0001
 172 #define CMD_ACT_SET_TX                  0x0002
 173 #define CMD_ACT_SET_BOTH                0x0003
 174 #define CMD_ACT_GET_RX                  0x0004
 175 #define CMD_ACT_GET_TX                  0x0008
 176 #define CMD_ACT_GET_BOTH                0x000c
 177
 178 /* Define action or option for CMD_802_11_PS_MODE */
 179 #define CMD_TYPE_CAM                    0x0000
 180 #define CMD_TYPE_MAX_PSP                0x0001
 181 #define CMD_TYPE_FAST_PSP               0x0002
 182
 183 /* Options for CMD_802_11_FW_WAKE_METHOD */
 184 #define CMD_WAKE_METHOD_UNCHANGED       0x0000
 185 #define CMD_WAKE_METHOD_COMMAND_INT     0x0001
 186 #define CMD_WAKE_METHOD_GPIO            0x0002
 187
 188 /* Object IDs for CMD_802_11_SNMP_MIB */
 189 #define SNMP_MIB_OID_BSS_TYPE           0x0000
 190 #define SNMP_MIB_OID_OP_RATE_SET        0x0001
 191 #define SNMP_MIB_OID_BEACON_PERIOD      0x0002  /* Reserved on v9+ */
 192 #define SNMP_MIB_OID_DTIM_PERIOD        0x0003  /* Reserved on v9+ */
 193 #define SNMP_MIB_OID_ASSOC_TIMEOUT      0x0004  /* Reserved on v9+ */
 194 #define SNMP_MIB_OID_RTS_THRESHOLD      0x0005
 195 #define SNMP_MIB_OID_SHORT_RETRY_LIMIT  0x0006
 196 #define SNMP_MIB_OID_LONG_RETRY_LIMIT   0x0007
 197 #define SNMP_MIB_OID_FRAG_THRESHOLD     0x0008
 198 #define SNMP_MIB_OID_11D_ENABLE         0x0009
 199 #define SNMP_MIB_OID_11H_ENABLE         0x000A
 200
 201 /* Define action or option for CMD_BT_ACCESS */
 202 enum cmd_bt_access_opts {
 203         /* The bt commands start at 5 instead of 1 because the old dft commands
 204          * are mapped to 1-4.  These old commands are no longer maintained and
 205          * should not be called.
 206          */
 207         CMD_ACT_BT_ACCESS_ADD = 5,
 208         CMD_ACT_BT_ACCESS_DEL,
 209         CMD_ACT_BT_ACCESS_LIST,
 210         CMD_ACT_BT_ACCESS_RESET,
 211         CMD_ACT_BT_ACCESS_SET_INVERT,
 212         CMD_ACT_BT_ACCESS_GET_INVERT
 213 };
 214
 215 /* Define action or option for CMD_FWT_ACCESS */
 216 enum cmd_fwt_access_opts {
 217         CMD_ACT_FWT_ACCESS_ADD = 1,
 218         CMD_ACT_FWT_ACCESS_DEL,
 219         CMD_ACT_FWT_ACCESS_LOOKUP,
 220         CMD_ACT_FWT_ACCESS_LIST,
 221         CMD_ACT_FWT_ACCESS_LIST_ROUTE,
 222         CMD_ACT_FWT_ACCESS_LIST_NEIGHBOR,
 223         CMD_ACT_FWT_ACCESS_RESET,
 224         CMD_ACT_FWT_ACCESS_CLEANUP,
 225         CMD_ACT_FWT_ACCESS_TIME,
 226 };
 227
 228 /* Define action or option for CMD_802_11_HOST_SLEEP_CFG */
 229 enum cmd_wol_cfg_opts {
 230         CMD_ACT_ACTION_NONE = 0,
 231         CMD_ACT_SET_WOL_RULE,
 232         CMD_ACT_GET_WOL_RULE,
 233         CMD_ACT_RESET_WOL_RULE,
 234 };
 235
 236 /* Define action or option for CMD_MESH_ACCESS */
 237 enum cmd_mesh_access_opts {
 238         CMD_ACT_MESH_GET_TTL = 1,
 239         CMD_ACT_MESH_SET_TTL,
 240         CMD_ACT_MESH_GET_STATS,
 241         CMD_ACT_MESH_GET_ANYCAST,
 242         CMD_ACT_MESH_SET_ANYCAST,
 243         CMD_ACT_MESH_SET_LINK_COSTS,
 244         CMD_ACT_MESH_GET_LINK_COSTS,
 245         CMD_ACT_MESH_SET_BCAST_RATE,
 246         CMD_ACT_MESH_GET_BCAST_RATE,
 247         CMD_ACT_MESH_SET_RREQ_DELAY,
 248         CMD_ACT_MESH_GET_RREQ_DELAY,
 249         CMD_ACT_MESH_SET_ROUTE_EXP,
 250         CMD_ACT_MESH_GET_ROUTE_EXP,
 251         CMD_ACT_MESH_SET_AUTOSTART_ENABLED,
 252         CMD_ACT_MESH_GET_AUTOSTART_ENABLED,
 253         CMD_ACT_MESH_SET_GET_PRB_RSP_LIMIT = 17,
 254 };
 255
 256 /* Define actions and types for CMD_MESH_CONFIG */
 257 enum cmd_mesh_config_actions {
 258         CMD_ACT_MESH_CONFIG_STOP = 0,
 259         CMD_ACT_MESH_CONFIG_START,
 260         CMD_ACT_MESH_CONFIG_SET,
 261         CMD_ACT_MESH_CONFIG_GET,
 262 };
 263
 264 enum cmd_mesh_config_types {
 265         CMD_TYPE_MESH_SET_BOOTFLAG = 1,
 266         CMD_TYPE_MESH_SET_BOOTTIME,
 267         CMD_TYPE_MESH_SET_DEF_CHANNEL,
 268         CMD_TYPE_MESH_SET_MESH_IE,
 269         CMD_TYPE_MESH_GET_DEFAULTS,
 270         CMD_TYPE_MESH_GET_MESH_IE, /* GET_DEFAULTS is superset of GET_MESHIE */
 271 };
 272
 273 /** Card Event definition */
 274 #define MACREG_INT_CODE_TX_PPA_FREE             0
 275 #define MACREG_INT_CODE_TX_DMA_DONE             1
 276 #define MACREG_INT_CODE_LINK_LOST_W_SCAN        2
 277 #define MACREG_INT_CODE_LINK_LOST_NO_SCAN       3
 278 #define MACREG_INT_CODE_LINK_SENSED             4
 279 #define MACREG_INT_CODE_CMD_FINISHED            5
 280 #define MACREG_INT_CODE_MIB_CHANGED             6
 281 #define MACREG_INT_CODE_INIT_DONE               7
 282 #define MACREG_INT_CODE_DEAUTHENTICATED         8
 283 #define MACREG_INT_CODE_DISASSOCIATED           9
 284 #define MACREG_INT_CODE_PS_AWAKE                10
 285 #define MACREG_INT_CODE_PS_SLEEP                11
 286 #define MACREG_INT_CODE_MIC_ERR_MULTICAST       13
 287 #define MACREG_INT_CODE_MIC_ERR_UNICAST         14
 288 #define MACREG_INT_CODE_WM_AWAKE                15
 289 #define MACREG_INT_CODE_DEEP_SLEEP_AWAKE        16
 290 #define MACREG_INT_CODE_ADHOC_BCN_LOST          17
 291 #define MACREG_INT_CODE_HOST_AWAKE              18
 292 #define MACREG_INT_CODE_STOP_TX                 19
 293 #define MACREG_INT_CODE_START_TX                20
 294 #define MACREG_INT_CODE_CHANNEL_SWITCH          21
 295 #define MACREG_INT_CODE_MEASUREMENT_RDY         22
 296 #define MACREG_INT_CODE_WMM_CHANGE              23
 297 #define MACREG_INT_CODE_BG_SCAN_REPORT          24
 298 #define MACREG_INT_CODE_RSSI_LOW                25
 299 #define MACREG_INT_CODE_SNR_LOW                 26
 300 #define MACREG_INT_CODE_MAX_FAIL                27
 301 #define MACREG_INT_CODE_RSSI_HIGH               28
 302 #define MACREG_INT_CODE_SNR_HIGH                29
 303 #define MACREG_INT_CODE_MESH_AUTO_STARTED       35
 304 #define MACREG_INT_CODE_FIRMWARE_READY          48
 305
 306 #endif