1 /* $NetBSD: opl3sa3reg.h,v 1.4 2005/12/11 12:21:28 christos Exp $ */
4 * Copyright (c) 1999 The NetBSD Foundation, Inc.
7 * This code is derived from software contributed to The NetBSD Foundation
10 * Redistribution and use in source and binary forms, with or without
11 * modification, are permitted provided that the following conditions
13 * 1. Redistributions of source code must retain the above copyright
14 * notice, this list of conditions and the following disclaimer.
15 * 2. Redistributions in binary form must reproduce the above copyright
16 * notice, this list of conditions and the following disclaimer in the
17 * documentation and/or other materials provided with the distribution.
19 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
20 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
21 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
22 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
23 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
24 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
25 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
26 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
27 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
28 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
29 * POSSIBILITY OF SUCH DAMAGE.
33 * YAMAHA YMF711 (OPL3 Single-chip Audio System 2; OPL3-SA2)
34 * YAMAHA YMF715x (OPL3 Single-chip Audio System 3; OPL3-SA3)
35 * control register description
37 * Other ports (SBpro, WSS CODEC, MPU401, OPL3, etc.) are NOT listed here.
40 /* [2]: OPL3-SA2 only, [3]: OPL3-SA3 only */
46 /* offset from the base address */
47 #define SA3_CTL_INDEX 0 /* Index port (R/W) */
48 #define SA3_CTL_DATA 1 /* Data register port (R/W) */
50 #define SA3_CTL_NPORT 2 /* number of ports */
56 #define SA3_PWR_MNG 0x01 /* Power management (R/W) */
57 #define SA2_PWR_MNG_SRST 0x80 /* [2] Software reset */
58 #define SA3_PWR_MNG_ADOWN 0x20 /* [3] Analog Down */
59 #define SA2_PWR_MNG_CLKO 0x10 /* [2] Master Clock disable */
60 #define SA2_PWR_MNG_FMPS 0x08 /* [2] OPL3 power down */
61 #define SA3_PWR_MNG_PSV 0x04 /* Power save */
62 #define SA3_PWR_MNG_PDN 0x02 /* Power down */
63 #define SA3_PWR_MNG_PDX 0x01 /* Oscillation stop */
64 #define SA3_PWR_MNG_DEFAULT 0x00 /* default value */
66 #define SA3_SYS_CTL 0x02 /* System control (R/W) */
67 #define SA3_SYS_CTL_SBHE 0x80 /* 0: AT-bus, 1: XT-bus */
68 #define SA3_SYS_CTL_YMODE 0x30 /* [3] 3D Enhancement mode */
69 #define SA3_SYS_CTL_YMODE0 0x00 /* Desktop mode (speaker 5-12cm) */
70 #define SA3_SYS_CTL_YMODE1 0x10 /* Notebook PC mode (1) (3cm) */
71 #define SA3_SYS_CTL_YMODE2 0x20 /* Notebook PC mode (2) (1.5cm) */
72 #define SA3_SYS_CTL_YMODE3 0x30 /* Hi-Fi mode (16-38cm) */
73 #define SA3_SYS_CTL_IDSEL 0x06 /* Specify DSP version of SBPro */
74 #define SA3_SYS_CTL_IDSEL0 0x00 /* major 0x03, minor 0x01 */
75 #define SA3_SYS_CTL_IDSEL1 0x02 /* major 0x02, minor 0x01 */
76 #define SA3_SYS_CTL_IDSEL2 0x04 /* major 0x01, minor 0x05 */
77 #define SA3_SYS_CTL_IDSEL3 0x06 /* major 0x00, minor 0x00 */
78 #define SA3_SYS_CTL_VZE 0x01 /* ZV */
79 #define SA3_SYS_CTL_DEFAULT 0x00 /* default value */
81 #define SA3_IRQ_CONF 0x03 /* Interrupt Channel config (R/W) */
82 #define SA3_IRQ_CONF_OPL3_B 0x80 /* OPL3 uses IRQ-B */
83 #define SA3_IRQ_CONF_MPU_B 0x40 /* MPU401 uses IRQ-B */
84 #define SA3_IRQ_CONF_SB_B 0x20 /* Sound Blaster uses IRQ-B */
85 #define SA3_IRQ_CONF_WSS_B 0x10 /* WSS CODEC uses IRQ-B */
86 #define SA3_IRQ_CONF_OPL3_A 0x08 /* OPL3 uses IRQ-A */
87 #define SA3_IRQ_CONF_MPU_A 0x04 /* MPU401 uses IRQ-A */
88 #define SA3_IRQ_CONF_SB_A 0x02 /* Sound Blaster uses IRQ-A */
89 #define SA3_IRQ_CONF_WSS_A 0x01 /* WSS CODEC uses IRQ-A */
90 #define SA3_IRQ_CONF_DEFAULT (SA3_IRQ_CONF_MPU_B | SA3_IRQ_CONF_SB_B | \
91 SA3_IRQ_CONF_OPL3_A | SA3_IRQ_CONF_WSS_A)
93 #define SA3_IRQA_STAT 0x04 /* Interrupt (IRQ-A) STATUS (RO) */
94 #define SA3_IRQB_STAT 0x05 /* Interrupt (IRQ-B) STATUS (RO) */
95 #define SA3_IRQ_STAT_MV 0x40 /* [3] Hardware Volume Interrupt */
96 #define SA3_IRQ_STAT_OPL3 0x20 /* Internal FM-synthesizer timer */
97 #define SA3_IRQ_STAT_MPU 0x10 /* MPU401 Interrupt */
98 #define SA3_IRQ_STAT_SB 0x08 /* Sound Blaster Playback Interrupt */
99 #define SA3_IRQ_STAT_TI 0x04 /* Timer Flag of CODEC */
100 #define SA3_IRQ_STAT_CI 0x02 /* Recording Flag of CODEC */
101 #define SA3_IRQ_STAT_PI 0x01 /* Playback Flag of CODEC */
103 #define SA3_DMA_CONF 0x06 /* DMA configuration (R/W) */
104 #define SA3_DMA_CONF_SB_B 0x40 /* Sound Blaster playback uses DMA-B */
105 #define SA3_DMA_CONF_WSS_R_B 0x20 /* WSS CODEC recording uses DMA-B */
106 #define SA3_DMA_CONF_WSS_P_B 0x10 /* WSS CODEC playback uses DMA-B */
107 #define SA3_DMA_CONF_SB_A 0x04 /* Sound Blaster playback uses DMA-A */
108 #define SA3_DMA_CONF_WSS_R_A 0x02 /* WSS CODEC recording uses DMA-A */
109 #define SA3_DMA_CONF_WSS_P_A 0x01 /* WSS CODEC playback uses DMA-A */
110 #define SA3_DMA_CONF_DEFAULT (SA3_DMA_CONF_SB_B | SA3_DMA_CONF_WSS_R_B | \
111 SA3_DMA_CONF_WSS_P_A)
113 #define SA3_VOL_L 0x07 /* Master Volume Lch (R/W) */
114 #define SA3_VOL_R 0x08 /* Master Volume Rch (R/W) */
115 #define SA3_VOL_MUTE 0x80 /* Mute the channel */
116 #define SA3_VOL_MV 0x0f /* Master Volume bits */
117 #define SA3_VOL_MV_0 0x00 /* 0dB (maximum volume) */
118 #define SA3_VOL_MV_2 0x01 /* -2dB */
119 #define SA3_VOL_MV_4 0x02 /* -4dB */
120 #define SA3_VOL_MV_6 0x03 /* -6dB */
121 #define SA3_VOL_MV_8 0x04 /* -8dB */
122 #define SA3_VOL_MV_10 0x05 /* -10dB */
123 #define SA3_VOL_MV_12 0x06 /* -12dB */
124 #define SA3_VOL_MV_14 0x07 /* -14dB (default) */
125 #define SA3_VOL_MV_16 0x08 /* -16dB */
126 #define SA3_VOL_MV_18 0x09 /* -18dB */
127 #define SA3_VOL_MV_20 0x0a /* -20dB */
128 #define SA3_VOL_MV_22 0x0b /* -22dB */
129 #define SA3_VOL_MV_24 0x0c /* -24dB */
130 #define SA3_VOL_MV_26 0x0d /* -26dB */
131 #define SA3_VOL_MV_28 0x0e /* -28dB */
132 #define SA3_VOL_MV_30 0x0f /* -30dB (minimum volume) */
133 #define SA3_VOL_DEFAULT SA3_VOL_MV_14
135 #define SA3_MIC_VOL 0x09 /* MIC Volume (R/W) */
136 #define SA3_MIC_MUTE 0x80 /* Mute Mic Volume */
137 #define SA3_MIC_MCV 0x1f /* Mic volume bits */
138 #define SA3_MIC_MCV12 0x00 /* +12.0dB (maximum volume) */
139 #define SA3_MIC_MCV10_5 0x01 /* +10.5dB */
140 #define SA3_MIC_MCV9 0x02 /* +9.0dB */
141 #define SA3_MIC_MCV7_5 0x03 /* +7.5dB */
142 #define SA3_MIC_MCV6 0x04 /* +6.0dB */
143 #define SA3_MIC_MCV4_5 0x05 /* +4.5dB */
144 #define SA3_MIC_MCV3 0x06 /* +3.0dB */
145 #define SA3_MIC_MCV1_5 0x07 /* +1.5dB */
146 #define SA3_MIC_MCV_0 0x08 /* 0.0dB (default) */
147 #define SA3_MIC_MCV_1_5 0x09 /* -1.5dB */
148 #define SA3_MIC_MCV_3_0 0x0a /* -3.0dB */
149 #define SA3_MIC_MCV_4_5 0x0b /* -4.5dB */
150 #define SA3_MIC_MCV_6 0x0c /* -6.0dB */
151 #define SA3_MIC_MCV_7_5 0x0d /* -7.5dB */
152 #define SA3_MIC_MCV_9 0x0e /* -9.0dB */
153 #define SA3_MIC_MCV_10_5 0x0f /* -10.5dB */
154 #define SA3_MIC_MCV_12 0x10 /* -12.0dB */
155 #define SA3_MIC_MCV_13_5 0x11 /* -13.5dB */
156 #define SA3_MIC_MCV_15 0x12 /* -15.0dB */
157 #define SA3_MIC_MCV_16_5 0x13 /* -16.5dB */
158 #define SA3_MIC_MCV_18 0x14 /* -18.0dB */
159 #define SA3_MIC_MCV_19_5 0x15 /* -19.5dB */
160 #define SA3_MIC_MCV_21 0x16 /* -21.0dB */
161 #define SA3_MIC_MCV_22_5 0x17 /* -22.5dB */
162 #define SA3_MIC_MCV_24 0x18 /* -24.0dB */
163 #define SA3_MIC_MCV_25_5 0x19 /* -25.5dB */
164 #define SA3_MIC_MCV_27 0x1a /* -27.0dB */
165 #define SA3_MIC_MCV_28_5 0x1b /* -28.5dB */
166 #define SA3_MIC_MCV_30 0x1c /* -30.0dB */
167 #define SA3_MIC_MCV_31_5 0x1d /* -31.5dB */
168 #define SA3_MIC_MCV_33 0x1e /* -33.0dB */
169 #define SA3_MIC_MCV_34_5 0x1f /* -34.5dB (minimum volume) */
170 #define SA3_MIC_VOL_DEFAULT (SA3_MIC_MUTE | SA3_MIC_MCV_0)
172 #define SA3_MISC 0x0a /* Miscellaneous */
173 #define SA3_MISC_VEN 0x80 /* Enable hardware volume control */
174 #define SA3_MISC_MCSW 0x10 /* A/D is connected to 0: Rch of Mic,
175 1: loopback of monaural output */
176 #define SA3_MISC_MODE 0x08 /* 0: SB mode, 1: WSS mode (RO) */
177 #define SA3_MISC_VER 0x07 /* Version of OPL3-SA2/OPL3-SA3 (RO) */
178 #define SA3_MISC_VER_711 1 /* OPL3-SA2 (YMF711) */
179 #define SA3_MISC_VER_715 2 /* OPL3-SA3 (YMF715) */
180 #define SA3_MISC_VER_715B 3 /* OPL3-SA3 (YMF715B) */
181 #define SA3_MISC_VER_715E 4 /* OPL3-SA3 (YMF715E) */
183 /*#define SA3_MISC_DEFAULT (SA3_MISC_VEN | version) */
185 /* WSS DMA Base counters (R/W) used for suspend/resume */
186 #define SA3_DMA_CNT_PLAY_LOW 0x0b /* Playback Base Counter (Low) */
187 #define SA3_DMA_CNT_PLAY_HIGH 0x0c /* Playback Base Counter (High) */
188 #define SA3_DMA_CNT_REC_LOW 0x0d /* Recording Base Counter (Low) */
189 #define SA3_DMA_CNT_REC_HIGH 0x0e /* Recording Base Counter (High) */
192 #define SA3_WSS_INT_SCAN 0x0f /* WSS Interrupt Scan out/in (R/W)*/
193 #define SA3_WSS_INT_SCAN_STI 0x04 /* 1: TI = "1" and IRQ active */
194 #define SA3_WSS_INT_SCAN_SCI 0x02 /* 1: CI = "1" and IRQ active */
195 #define SA3_WSS_INT_SCAN_SPI 0x01 /* 1: PI = "1" and IRQ active */
196 #define SA3_WSS_INT_DEFAULT 0x00 /* default value */
199 #define SA3_SB_SCAN 0x10 /* SB Internal State Scan out/in (R/W)*/
200 #define SA3_SB_SCAN_SBPDA 0x80 /* Sound Blaster Power Down ack */
201 #define SA3_SB_SCAN_SS 0x08 /* Scan Select */
202 #define SA3_SB_SCAN_SM 0x04 /* Scan Mode 1: read out, 0: write in */
203 #define SA3_SB_SCAN_SE 0x02 /* Scan Enable */
204 #define SA3_SB_SCAN_SBPDR 0x01 /* Sound Blaster Power Down Request */
205 #define SA3_SB_SCAN_DEFAULT 0x00 /* default value */
208 #define SA3_SB_SCAN_DATA 0x11 /* SB Internal State Scan Data (R/W)*/
211 #define SA3_DPWRDWN 0x12 /* Digital Partial Power Down (R/W) */
212 #define SA3_DPWRDWN_JOY 0x80 /* Joystick power down */
213 #define SA3_DPWRDWN_MPU 0x40 /* MPU401 power down */
214 #define SA3_DPWRDWN_MCLKO 0x20 /* Master Clock disable */
215 #define SA3_DPWRDWN_FM 0x10 /* FM (OPL3) power down */
216 #define SA3_DPWRDWN_WSS_R 0x08 /* WSS recording power down */
217 #define SA3_DPWRDWN_WSS_P 0x04 /* WSS playback power down */
218 #define SA3_DPWRDWN_SB 0x02 /* Sound Blaster power down */
219 #define SA3_DPWRDWN_PNP 0x01 /* PnP power down */
220 #define SA3_DPWRDWN_DEFAULT 0x00 /* default value */
223 #define SA3_APWRDWN 0x13 /* Analog Partial Power Down (R/W) */
224 #define SA3_APWRDWN_FMDAC 0x10 /* FMDAC for OPL3 power down */
225 #define SA3_APWRDWN_AD 0x08 /* A/D for WSS recording power down */
226 #define SA3_APWRDWN_DA 0x04 /* D/A for WSS playback power down */
227 #define SA3_APWRDWN_SBDAC 0x02 /* D/A for SB power down */
228 #define SA3_APWRDWN_WIDE 0x01 /* Wide Stereo power down */
229 #define SA3_APWRDWN_DEFAULT 0x00 /* default value */
232 #define SA3_3D_WIDE 0x14 /* 3D Enhanced control (WIDE) (R/W) */
233 #define SA3_3D_WIDE_WIDER 0x70 /* Rch of wide 3D enhanced control */
234 #define SA3_3D_WIDE_WIDEL 0x07 /* Lch of wide 3D enhanced control */
235 #define SA3_3D_WIDE_DEFAULT 0x00 /* default value */
238 #define SA3_3D_BASS 0x15 /* 3D Enhanced control (BASS) (R/W) */
239 #define SA3_3D_BASS_BASSR 0x70 /* Rch of bass 3D enhanced control */
240 #define SA3_3D_BASS_BASSL 0x07 /* Lch of bass 3D enhanced control */
241 #define SA3_3D_BASS_DEFAULT 0x00 /* default value */
244 #define SA3_3D_TREBLE 0x16 /* 3D Enhanced control (TREBLE) (R/W) */
245 #define SA3_3D_TREBLE_TRER 0x70 /* Rch of treble 3D enhanced control */
246 #define SA3_3D_TREBLE_TREL 0x07 /* Lch of treble 3D enhanced control */
247 #define SA3_3D_TREBLE_DEFAULT 0x00 /* default value */
249 /* common to the 3D enhance registers */
250 #define SA3_3D_BITS 0x07
251 #define SA3_3D_LSHIFT 0
252 #define SA3_3D_RSHIFT 4
255 #define SA3_HVOL_INTR_CNF 0x17 /* Hardware Volume Intr Channel (R/W) */
256 #define SA3_HVOL_INTR_CNF_B 0x20 /* Hardware Volume uses IRQ-B */
257 #define SA3_HVOL_INTR_CNF_A 0x10 /* Hardware Volume uses IRQ-A */
258 #define SA3_HVOL_INTR_CNF_DEFAULT 0x00
261 #define SA3_MULTI_STAT 0x18 /* Multi-purpose Select Pin Stat (RO) */
262 #define SA3_MULTI_STAT_SEL 0x70 /* State of SEL2-0 pins */
