drivers/net/atp.h

   1 /* Linux header file for the ATP pocket ethernet adapter. */
   2 /* v1.09 8/9/2000 becker@scyld.com. */
   3
   4 #include <linux/if_ether.h>
   5 #include <linux/types.h>
   6
   7 /* The header prepended to received packets. */
   8 struct rx_header {
   9     ushort pad;                 /* Pad. */
  10     ushort rx_count;
  11     ushort rx_status;           /* Unknown bit assignments :-<.  */
  12     ushort cur_addr;            /* Apparently the current buffer address(?) */
  13 };
  14
  15 #define PAR_DATA        0
  16 #define PAR_STATUS      1
  17 #define PAR_CONTROL 2
  18
  19 enum chip_type { RTL8002, RTL8012 };
  20
  21 #define Ctrl_LNibRead   0x08    /* LP_PSELECP */
  22 #define Ctrl_HNibRead   0
  23 #define Ctrl_LNibWrite  0x08    /* LP_PSELECP */
  24 #define Ctrl_HNibWrite  0
  25 #define Ctrl_SelData    0x04    /* LP_PINITP */
  26 #define Ctrl_IRQEN      0x10    /* LP_PINTEN */
  27
  28 #define EOW     0xE0
  29 #define EOC     0xE0
  30 #define WrAddr  0x40    /* Set address of EPLC read, write register. */
  31 #define RdAddr  0xC0
  32 #define HNib    0x10
  33
  34 enum page0_regs
  35 {
  36     /* The first six registers hold the ethernet physical station address. */
  37     PAR0 = 0, PAR1 = 1, PAR2 = 2, PAR3 = 3, PAR4 = 4, PAR5 = 5,
  38     TxCNT0 = 6, TxCNT1 = 7,             /* The transmit byte count. */
  39     TxSTAT = 8, RxSTAT = 9,             /* Tx and Rx status. */
  40     ISR = 10, IMR = 11,                 /* Interrupt status and mask. */
  41     CMR1 = 12,                          /* Command register 1. */
  42     CMR2 = 13,                          /* Command register 2. */
  43     MODSEL = 14,                        /* Mode select register. */
  44     MAR = 14,                           /* Memory address register (?). */
  45     CMR2_h = 0x1d, };
  46
  47 enum eepage_regs
  48 { PROM_CMD = 6, PROM_DATA = 7 };        /* Note that PROM_CMD is in the "high" bits. */
  49
  50
  51 #define ISR_TxOK        0x01
  52 #define ISR_RxOK        0x04
  53 #define ISR_TxErr       0x02
  54 #define ISRh_RxErr      0x11    /* ISR, high nibble */
  55
  56 #define CMR1h_MUX       0x08    /* Select printer multiplexor on 8012. */
  57 #define CMR1h_RESET     0x04    /* Reset. */
  58 #define CMR1h_RxENABLE  0x02    /* Rx unit enable.  */
  59 #define CMR1h_TxENABLE  0x01    /* Tx unit enable.  */
  60 #define CMR1h_TxRxOFF   0x00
  61 #define CMR1_ReXmit     0x08    /* Trigger a retransmit. */
  62 #define CMR1_Xmit       0x04    /* Trigger a transmit. */
  63 #define CMR1_IRQ        0x02    /* Interrupt active. */
  64 #define CMR1_BufEnb     0x01    /* Enable the buffer(?). */
  65 #define CMR1_NextPkt    0x01    /* Enable the buffer(?). */
  66
  67 #define CMR2_NULL       8
  68 #define CMR2_IRQOUT     9
  69 #define CMR2_RAMTEST    10
  70 #define CMR2_EEPROM     12      /* Set to page 1, for reading the EEPROM. */
  71
  72 #define CMR2h_OFF       0       /* No accept mode. */
  73 #define CMR2h_Physical  1       /* Accept a physical address match only. */
  74 #define CMR2h_Normal    2       /* Accept physical and broadcast address. */
  75 #define CMR2h_PROMISC   3       /* Promiscuous mode. */
  76
  77 /* An inline function used below: it differs from inb() by explicitly return an unsigned
  78    char, saving a truncation. */
  79 static inline unsigned char inbyte(unsigned short port)
  80 {
  81     unsigned char _v;
  82     __asm__ __volatile__ ("inb %w1,%b0" :"=a" (_v):"d" (port));
  83     return _v;
  84 }
  85
  86 /* Read register OFFSET.
  87    This command should always be terminated with read_end(). */
  88 static inline unsigned char read_nibble(short port, unsigned char offset)
  89 {
  90     unsigned char retval;
  91     outb(EOC+offset, port + PAR_DATA);
  92     outb(RdAddr+offset, port + PAR_DATA);
  93     inbyte(port + PAR_STATUS);          /* Settling time delay */
  94     retval = inbyte(port + PAR_STATUS);
  95     outb(EOC+offset, port + PAR_DATA);
  96
  97     return retval;
  98 }
  99
 100 /* Functions for bulk data read.  The interrupt line is always disabled. */
 101 /* Get a byte using read mode 0, reading data from the control lines. */
 102 static inline unsigned char read_byte_mode0(short ioaddr)
 103 {
 104     unsigned char low_nib;
 105
 106     outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL);
 107     inbyte(ioaddr + PAR_STATUS);
 108     low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f;
 109     outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL);
 110     inbyte(ioaddr + PAR_STATUS);        /* Settling time delay -- needed!  */
 111     inbyte(ioaddr + PAR_STATUS);        /* Settling time delay -- needed!  */
 112     return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0);
 113 }
 114
 115 /* The same as read_byte_mode0(), but does multiple inb()s for stability. */
 116 static inline unsigned char read_byte_mode2(short ioaddr)
 117 {
 118     unsigned char low_nib;
 119
 120     outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL);
 121     inbyte(ioaddr + PAR_STATUS);
 122     low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f;
 123     outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL);
 124     inbyte(ioaddr + PAR_STATUS);        /* Settling time delay -- needed!  */
 125     return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0);
 126 }
 127
 128 /* Read a byte through the data register. */
 129 static inline unsigned char read_byte_mode4(short ioaddr)
 130 {
 131     unsigned char low_nib;
 132
 133     outb(RdAddr | MAR, ioaddr + PAR_DATA);
 134     low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f;
 135     outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA);
 136     return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0);
 137 }
 138
 139 /* Read a byte through the data register, double reading to allow settling. */
 140 static inline unsigned char read_byte_mode6(short ioaddr)
 141 {
 142     unsigned char low_nib;
 143
 144     outb(RdAddr | MAR, ioaddr + PAR_DATA);
 145     inbyte(ioaddr + PAR_STATUS);
 146     low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f;
 147     outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA);
 148     inbyte(ioaddr + PAR_STATUS);
 149     return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0);
 150 }
 151
 152 static inline void
 153 write_reg(short port, unsigned char reg, unsigned char value)
 154 {
 155     unsigned char outval;
 156     outb(EOC | reg, port + PAR_DATA);
 157     outval = WrAddr | reg;
 158     outb(outval, port + PAR_DATA);
 159     outb(outval, port + PAR_DATA);      /* Double write for PS/2. */
 160
 161     outval &= 0xf0;
 162     outval |= value;
 163     outb(outval, port + PAR_DATA);
 164     outval &= 0x1f;
 165     outb(outval, port + PAR_DATA);
 166     outb(outval, port + PAR_DATA);
 167
 168     outb(EOC | outval, port + PAR_DATA);
 169 }
 170
 171 static inline void
 172 write_reg_high(short port, unsigned char reg, unsigned char value)
 173 {
 174     unsigned char outval = EOC | HNib | reg;
 175
 176     outb(outval, port + PAR_DATA);
 177     outval &= WrAddr | HNib | 0x0f;
 178     outb(outval, port + PAR_DATA);
 179     outb(outval, port + PAR_DATA);      /* Double write for PS/2. */
 180
 181     outval = WrAddr | HNib | value;
 182     outb(outval, port + PAR_DATA);
 183     outval &= HNib | 0x0f;              /* HNib | value */
 184     outb(outval, port + PAR_DATA);
 185     outb(outval, port + PAR_DATA);
 186
 187     outb(EOC | HNib | outval, port + PAR_DATA);
 188 }
 189
 190 /* Write a byte out using nibble mode.  The low nibble is written first. */
 191 static inline void
 192 write_reg_byte(short port, unsigned char reg, unsigned char value)
 193 {
 194     unsigned char outval;
 195     outb(EOC | reg, port + PAR_DATA);   /* Reset the address register. */
 196     outval = WrAddr | reg;
 197     outb(outval, port + PAR_DATA);
 198     outb(outval, port + PAR_DATA);      /* Double write for PS/2. */
 199
 200     outb((outval & 0xf0) | (value & 0x0f), port + PAR_DATA);
 201     outb(value & 0x0f, port + PAR_DATA);
 202     value >>= 4;
 203     outb(value, port + PAR_DATA);
 204     outb(0x10 | value, port + PAR_DATA);
 205     outb(0x10 | value, port + PAR_DATA);
 206
 207     outb(EOC  | value, port + PAR_DATA);        /* Reset the address register. */
 208 }
 209
 210 /*
 211  * Bulk data writes to the packet buffer.  The interrupt line remains enabled.
 212  * The first, faster method uses only the dataport (data modes 0, 2 & 4).
 213  * The second (backup) method uses data and control regs (modes 1, 3 & 5).
 214  * It should only be needed when there is skew between the individual data
 215  * lines.
 216  */
 217 static inline void write_byte_mode0(short ioaddr, unsigned char value)
 218 {
 219     outb(value & 0x0f, ioaddr + PAR_DATA);
 220     outb((value>>4) | 0x10, ioaddr + PAR_DATA);
 221 }
 222
 223 static inline void write_byte_mode1(short ioaddr, unsigned char value)
 224 {
 225     outb(value & 0x0f, ioaddr + PAR_DATA);
 226     outb(Ctrl_IRQEN | Ctrl_LNibWrite, ioaddr + PAR_CONTROL);
 227     outb((value>>4) | 0x10, ioaddr + PAR_DATA);
 228     outb(Ctrl_IRQEN | Ctrl_HNibWrite, ioaddr + PAR_CONTROL);
 229 }
 230
 231 /* Write 16bit VALUE to the packet buffer: the same as above just doubled. */
 232 static inline void write_word_mode0(short ioaddr, unsigned short value)
 233 {
 234     outb(value & 0x0f, ioaddr + PAR_DATA);
 235     value >>= 4;
 236     outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA);
 237     value >>= 4;
 238     outb(value & 0x0f, ioaddr + PAR_DATA);
 239     value >>= 4;
 240     outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA);
 241 }
 242
 243 /*  EEPROM_Ctrl bits. */
 244 #define EE_SHIFT_CLK    0x04    /* EEPROM shift clock. */
 245 #define EE_CS           0x02    /* EEPROM chip select. */
 246 #define EE_CLK_HIGH     0x12
 247 #define EE_CLK_LOW      0x16
 248 #define EE_DATA_WRITE   0x01    /* EEPROM chip data in. */
 249 #define EE_DATA_READ    0x08    /* EEPROM chip data out. */
 250
 251 /* Delay between EEPROM clock transitions. */
 252 #define eeprom_delay(ticks) \
 253 do { int _i = 40; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0)
 254
 255 /* The EEPROM commands include the alway-set leading bit. */
 256 #define EE_WRITE_CMD(offset)    (((5 << 6) + (offset)) << 17)
 257 #define EE_READ(offset)         (((6 << 6) + (offset)) << 17)
 258 #define EE_ERASE(offset)        (((7 << 6) + (offset)) << 17)
 259 #define EE_CMD_SIZE     27      /* The command+address+data size. */