fs: use kmem_cache_zalloc instead
[pv_ops_mirror.git] / include / asm-m68knommu / m5249sim.h
blob399814f0b219fee7468f84321064aa58f2ac9020
1 /****************************************************************************/
3 /*
4 * m5249sim.h -- ColdFire 5249 System Integration Module support.
6 * (C) Copyright 2002, Greg Ungerer (gerg@snapgear.com)
7 */
9 /****************************************************************************/
10 #ifndef m5249sim_h
11 #define m5249sim_h
12 /****************************************************************************/
15 * Define the 5249 SIM register set addresses.
17 #define MCFSIM_RSR 0x00 /* Reset Status reg (r/w) */
18 #define MCFSIM_SYPCR 0x01 /* System Protection reg (r/w)*/
19 #define MCFSIM_SWIVR 0x02 /* SW Watchdog intr reg (r/w) */
20 #define MCFSIM_SWSR 0x03 /* SW Watchdog service (r/w) */
21 #define MCFSIM_PAR 0x04 /* Pin Assignment reg (r/w) */
22 #define MCFSIM_IRQPAR 0x06 /* Interrupt Assignment reg (r/w) */
23 #define MCFSIM_MPARK 0x0C /* BUS Master Control Reg*/
24 #define MCFSIM_IPR 0x40 /* Interrupt Pend reg (r/w) */
25 #define MCFSIM_IMR 0x44 /* Interrupt Mask reg (r/w) */
26 #define MCFSIM_AVR 0x4b /* Autovector Ctrl reg (r/w) */
27 #define MCFSIM_ICR0 0x4c /* Intr Ctrl reg 0 (r/w) */
28 #define MCFSIM_ICR1 0x4d /* Intr Ctrl reg 1 (r/w) */
29 #define MCFSIM_ICR2 0x4e /* Intr Ctrl reg 2 (r/w) */
30 #define MCFSIM_ICR3 0x4f /* Intr Ctrl reg 3 (r/w) */
31 #define MCFSIM_ICR4 0x50 /* Intr Ctrl reg 4 (r/w) */
32 #define MCFSIM_ICR5 0x51 /* Intr Ctrl reg 5 (r/w) */
33 #define MCFSIM_ICR6 0x52 /* Intr Ctrl reg 6 (r/w) */
34 #define MCFSIM_ICR7 0x53 /* Intr Ctrl reg 7 (r/w) */
35 #define MCFSIM_ICR8 0x54 /* Intr Ctrl reg 8 (r/w) */
36 #define MCFSIM_ICR9 0x55 /* Intr Ctrl reg 9 (r/w) */
37 #define MCFSIM_ICR10 0x56 /* Intr Ctrl reg 10 (r/w) */
38 #define MCFSIM_ICR11 0x57 /* Intr Ctrl reg 11 (r/w) */
40 #define MCFSIM_CSAR0 0x80 /* CS 0 Address 0 reg (r/w) */
41 #define MCFSIM_CSMR0 0x84 /* CS 0 Mask 0 reg (r/w) */
42 #define MCFSIM_CSCR0 0x8a /* CS 0 Control reg (r/w) */
43 #define MCFSIM_CSAR1 0x8c /* CS 1 Address reg (r/w) */
44 #define MCFSIM_CSMR1 0x90 /* CS 1 Mask reg (r/w) */
45 #define MCFSIM_CSCR1 0x96 /* CS 1 Control reg (r/w) */
46 #define MCFSIM_CSAR2 0x98 /* CS 2 Adress reg (r/w) */
47 #define MCFSIM_CSMR2 0x9c /* CS 2 Mask reg (r/w) */
48 #define MCFSIM_CSCR2 0xa2 /* CS 2 Control reg (r/w) */
49 #define MCFSIM_CSAR3 0xa4 /* CS 3 Adress reg (r/w) */
50 #define MCFSIM_CSMR3 0xa8 /* CS 3 Mask reg (r/w) */
51 #define MCFSIM_CSCR3 0xae /* CS 3 Control reg (r/w) */
53 #define MCFSIM_DCR 0x100 /* DRAM Control reg (r/w) */
54 #define MCFSIM_DACR0 0x108 /* DRAM 0 Addr and Ctrl (r/w) */
55 #define MCFSIM_DMR0 0x10c /* DRAM 0 Mask reg (r/w) */
56 #define MCFSIM_DACR1 0x110 /* DRAM 1 Addr and Ctrl (r/w) */
57 #define MCFSIM_DMR1 0x114 /* DRAM 1 Mask reg (r/w) */
61 * Some symbol defines for the above...
63 #define MCFSIM_SWDICR MCFSIM_ICR0 /* Watchdog timer ICR */
64 #define MCFSIM_TIMER1ICR MCFSIM_ICR1 /* Timer 1 ICR */
65 #define MCFSIM_TIMER2ICR MCFSIM_ICR2 /* Timer 2 ICR */
66 #define MCFSIM_UART1ICR MCFSIM_ICR4 /* UART 1 ICR */
67 #define MCFSIM_UART2ICR MCFSIM_ICR5 /* UART 2 ICR */
68 #define MCFSIM_DMA0ICR MCFSIM_ICR6 /* DMA 0 ICR */
69 #define MCFSIM_DMA1ICR MCFSIM_ICR7 /* DMA 1 ICR */
70 #define MCFSIM_DMA2ICR MCFSIM_ICR8 /* DMA 2 ICR */
71 #define MCFSIM_DMA3ICR MCFSIM_ICR9 /* DMA 3 ICR */
74 * General purpose IO registers (in MBAR2).
76 #define MCFSIM2_GPIOREAD 0x0 /* GPIO read values */
77 #define MCFSIM2_GPIOWRITE 0x4 /* GPIO write values */
78 #define MCFSIM2_GPIOENABLE 0x8 /* GPIO enabled */
79 #define MCFSIM2_GPIOFUNC 0xc /* GPIO function */
80 #define MCFSIM2_GPIO1READ 0xb0 /* GPIO1 read values */
81 #define MCFSIM2_GPIO1WRITE 0xb4 /* GPIO1 write values */
82 #define MCFSIM2_GPIO1ENABLE 0xb8 /* GPIO1 enabled */
83 #define MCFSIM2_GPIO1FUNC 0xbc /* GPIO1 function */
85 #define MCFSIM2_GPIOINTSTAT 0xc0 /* GPIO interrupt status */
86 #define MCFSIM2_GPIOINTCLEAR 0xc0 /* GPIO interrupt clear */
87 #define MCFSIM2_GPIOINTENABLE 0xc4 /* GPIO interrupt enable */
89 #define MCFSIM2_INTLEVEL1 0x140 /* Interrupt level reg 1 */
90 #define MCFSIM2_INTLEVEL2 0x144 /* Interrupt level reg 2 */
91 #define MCFSIM2_INTLEVEL3 0x148 /* Interrupt level reg 3 */
92 #define MCFSIM2_INTLEVEL4 0x14c /* Interrupt level reg 4 */
93 #define MCFSIM2_INTLEVEL5 0x150 /* Interrupt level reg 5 */
94 #define MCFSIM2_INTLEVEL6 0x154 /* Interrupt level reg 6 */
95 #define MCFSIM2_INTLEVEL7 0x158 /* Interrupt level reg 7 */
96 #define MCFSIM2_INTLEVEL8 0x15c /* Interrupt level reg 8 */
98 #define MCFSIM2_DMAROUTE 0x188 /* DMA routing */
100 #define MCFSIM2_IDECONFIG1 0x18c /* IDEconfig1 */
101 #define MCFSIM2_IDECONFIG2 0x190 /* IDEconfig2 */
105 * Macro to set IMR register. It is 32 bits on the 5249.
107 #define MCFSIM_IMR_MASKALL 0x7fffe /* All SIM intr sources */
109 #define mcf_getimr() \
110 *((volatile unsigned long *) (MCF_MBAR + MCFSIM_IMR))
112 #define mcf_setimr(imr) \
113 *((volatile unsigned long *) (MCF_MBAR + MCFSIM_IMR)) = (imr);
115 #define mcf_getipr() \
116 *((volatile unsigned long *) (MCF_MBAR + MCFSIM_IPR))
118 /****************************************************************************/
120 #ifdef __ASSEMBLER__
123 * The M5249C3 board needs a little help getting all its SIM devices
124 * initialized at kernel start time. dBUG doesn't set much up, so
125 * we need to do it manually.
127 .macro m5249c3_setup
129 * Set MBAR1 and MBAR2, just incase they are not set.
131 movel #0x10000001,%a0
132 movec %a0,%MBAR /* map MBAR region */
133 subql #1,%a0 /* get MBAR address in a0 */
135 movel #0x80000001,%a1
136 movec %a1,#3086 /* map MBAR2 region */
137 subql #1,%a1 /* get MBAR2 address in a1 */
140 * Move secondary interrupts to base at 128.
142 moveb #0x80,%d0
143 moveb %d0,0x16b(%a1) /* interrupt base register */
146 * Work around broken CSMR0/DRAM vector problem.
148 movel #0x001F0021,%d0 /* disable C/I bit */
149 movel %d0,0x84(%a0) /* set CSMR0 */
152 * Disable the PLL firstly. (Who knows what state it is
153 * in here!).
155 movel 0x180(%a1),%d0 /* get current PLL value */
156 andl #0xfffffffe,%d0 /* PLL bypass first */
157 movel %d0,0x180(%a1) /* set PLL register */
160 #if CONFIG_CLOCK_FREQ == 140000000
162 * Set initial clock frequency. This assumes M5249C3 board
163 * is fitted with 11.2896MHz crystal. It will program the
164 * PLL for 140MHz. Lets go fast :-)
166 movel #0x125a40f0,%d0 /* set for 140MHz */
167 movel %d0,0x180(%a1) /* set PLL register */
168 orl #0x1,%d0
169 movel %d0,0x180(%a1) /* set PLL register */
170 #endif
173 * Setup CS1 for ethernet controller.
174 * (Setup as per M5249C3 doco).
176 movel #0xe0000000,%d0 /* CS1 mapped at 0xe0000000 */
177 movel %d0,0x8c(%a0)
178 movel #0x001f0021,%d0 /* CS1 size of 1Mb */
179 movel %d0,0x90(%a0)
180 movew #0x0080,%d0 /* CS1 = 16bit port, AA */
181 movew %d0,0x96(%a0)
184 * Setup CS2 for IDE interface.
186 movel #0x50000000,%d0 /* CS2 mapped at 0x50000000 */
187 movel %d0,0x98(%a0)
188 movel #0x001f0001,%d0 /* CS2 size of 1MB */
189 movel %d0,0x9c(%a0)
190 movew #0x0080,%d0 /* CS2 = 16bit, TA */
191 movew %d0,0xa2(%a0)
193 movel #0x00107000,%d0 /* IDEconfig1 */
194 movel %d0,0x18c(%a1)
195 movel #0x000c0400,%d0 /* IDEconfig2 */
196 movel %d0,0x190(%a1)
198 movel #0x00080000,%d0 /* GPIO19, IDE reset bit */
199 orl %d0,0xc(%a1) /* function GPIO19 */
200 orl %d0,0x8(%a1) /* enable GPIO19 as output */
201 orl %d0,0x4(%a1) /* de-assert IDE reset */
202 .endm
204 #define PLATFORM_SETUP m5249c3_setup
206 #endif /* __ASSEMBLER__ */
208 /****************************************************************************/
209 #endif /* m5249sim_h */