Pull bugzilla-9429 into release branch
[pv_ops_mirror.git] / drivers / net / wireless / net2280.h
blob120eb831b287c4c50cbc2f545b39370fa2526bfb
1 #ifndef NET2280_H
2 #define NET2280_H
3 /*
4 * NetChip 2280 high/full speed USB device controller.
5 * Unlike many such controllers, this one talks PCI.
6 */
8 /*
9 * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com)
10 * Copyright (C) 2003 David Brownell
12 * This program is free software; you can redistribute it and/or modify
13 * it under the terms of the GNU General Public License as published by
14 * the Free Software Foundation; either version 2 of the License, or
15 * (at your option) any later version.
17 * This program is distributed in the hope that it will be useful,
18 * but WITHOUT ANY WARRANTY; without even the implied warranty of
19 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
20 * GNU General Public License for more details.
22 * You should have received a copy of the GNU General Public License
23 * along with this program; if not, write to the Free Software
24 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
27 /*-------------------------------------------------------------------------*/
29 /* NET2280 MEMORY MAPPED REGISTERS
31 * The register layout came from the chip documentation, and the bit
32 * number definitions were extracted from chip specification.
34 * Use the shift operator ('<<') to build bit masks, with readl/writel
35 * to access the registers through PCI.
38 /* main registers, BAR0 + 0x0000 */
39 struct net2280_regs {
40 // offset 0x0000
41 __le32 devinit;
42 #define LOCAL_CLOCK_FREQUENCY 8
43 #define FORCE_PCI_RESET 7
44 #define PCI_ID 6
45 #define PCI_ENABLE 5
46 #define FIFO_SOFT_RESET 4
47 #define CFG_SOFT_RESET 3
48 #define PCI_SOFT_RESET 2
49 #define USB_SOFT_RESET 1
50 #define M8051_RESET 0
51 __le32 eectl;
52 #define EEPROM_ADDRESS_WIDTH 23
53 #define EEPROM_CHIP_SELECT_ACTIVE 22
54 #define EEPROM_PRESENT 21
55 #define EEPROM_VALID 20
56 #define EEPROM_BUSY 19
57 #define EEPROM_CHIP_SELECT_ENABLE 18
58 #define EEPROM_BYTE_READ_START 17
59 #define EEPROM_BYTE_WRITE_START 16
60 #define EEPROM_READ_DATA 8
61 #define EEPROM_WRITE_DATA 0
62 __le32 eeclkfreq;
63 u32 _unused0;
64 // offset 0x0010
66 __le32 pciirqenb0; /* interrupt PCI master ... */
67 #define SETUP_PACKET_INTERRUPT_ENABLE 7
68 #define ENDPOINT_F_INTERRUPT_ENABLE 6
69 #define ENDPOINT_E_INTERRUPT_ENABLE 5
70 #define ENDPOINT_D_INTERRUPT_ENABLE 4
71 #define ENDPOINT_C_INTERRUPT_ENABLE 3
72 #define ENDPOINT_B_INTERRUPT_ENABLE 2
73 #define ENDPOINT_A_INTERRUPT_ENABLE 1
74 #define ENDPOINT_0_INTERRUPT_ENABLE 0
75 __le32 pciirqenb1;
76 #define PCI_INTERRUPT_ENABLE 31
77 #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
78 #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
79 #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
80 #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
81 #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
82 #define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18
83 #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
84 #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
85 #define GPIO_INTERRUPT_ENABLE 13
86 #define DMA_D_INTERRUPT_ENABLE 12
87 #define DMA_C_INTERRUPT_ENABLE 11
88 #define DMA_B_INTERRUPT_ENABLE 10
89 #define DMA_A_INTERRUPT_ENABLE 9
90 #define EEPROM_DONE_INTERRUPT_ENABLE 8
91 #define VBUS_INTERRUPT_ENABLE 7
92 #define CONTROL_STATUS_INTERRUPT_ENABLE 6
93 #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
94 #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
95 #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
96 #define RESUME_INTERRUPT_ENABLE 1
97 #define SOF_INTERRUPT_ENABLE 0
98 __le32 cpu_irqenb0; /* ... or onboard 8051 */
99 #define SETUP_PACKET_INTERRUPT_ENABLE 7
100 #define ENDPOINT_F_INTERRUPT_ENABLE 6
101 #define ENDPOINT_E_INTERRUPT_ENABLE 5
102 #define ENDPOINT_D_INTERRUPT_ENABLE 4
103 #define ENDPOINT_C_INTERRUPT_ENABLE 3
104 #define ENDPOINT_B_INTERRUPT_ENABLE 2
105 #define ENDPOINT_A_INTERRUPT_ENABLE 1
106 #define ENDPOINT_0_INTERRUPT_ENABLE 0
107 __le32 cpu_irqenb1;
108 #define CPU_INTERRUPT_ENABLE 31
109 #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
110 #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
111 #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
112 #define PCI_INTA_INTERRUPT_ENABLE 24
113 #define PCI_PME_INTERRUPT_ENABLE 23
114 #define PCI_SERR_INTERRUPT_ENABLE 22
115 #define PCI_PERR_INTERRUPT_ENABLE 21
116 #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
117 #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
118 #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
119 #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
120 #define GPIO_INTERRUPT_ENABLE 13
121 #define DMA_D_INTERRUPT_ENABLE 12
122 #define DMA_C_INTERRUPT_ENABLE 11
123 #define DMA_B_INTERRUPT_ENABLE 10
124 #define DMA_A_INTERRUPT_ENABLE 9
125 #define EEPROM_DONE_INTERRUPT_ENABLE 8
126 #define VBUS_INTERRUPT_ENABLE 7
127 #define CONTROL_STATUS_INTERRUPT_ENABLE 6
128 #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
129 #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
130 #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
131 #define RESUME_INTERRUPT_ENABLE 1
132 #define SOF_INTERRUPT_ENABLE 0
134 // offset 0x0020
135 u32 _unused1;
136 __le32 usbirqenb1;
137 #define USB_INTERRUPT_ENABLE 31
138 #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
139 #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
140 #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
141 #define PCI_INTA_INTERRUPT_ENABLE 24
142 #define PCI_PME_INTERRUPT_ENABLE 23
143 #define PCI_SERR_INTERRUPT_ENABLE 22
144 #define PCI_PERR_INTERRUPT_ENABLE 21
145 #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
146 #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
147 #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
148 #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
149 #define GPIO_INTERRUPT_ENABLE 13
150 #define DMA_D_INTERRUPT_ENABLE 12
151 #define DMA_C_INTERRUPT_ENABLE 11
152 #define DMA_B_INTERRUPT_ENABLE 10
153 #define DMA_A_INTERRUPT_ENABLE 9
154 #define EEPROM_DONE_INTERRUPT_ENABLE 8
155 #define VBUS_INTERRUPT_ENABLE 7
156 #define CONTROL_STATUS_INTERRUPT_ENABLE 6
157 #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
158 #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
159 #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
160 #define RESUME_INTERRUPT_ENABLE 1
161 #define SOF_INTERRUPT_ENABLE 0
162 __le32 irqstat0;
163 #define INTA_ASSERTED 12
164 #define SETUP_PACKET_INTERRUPT 7
165 #define ENDPOINT_F_INTERRUPT 6
166 #define ENDPOINT_E_INTERRUPT 5
167 #define ENDPOINT_D_INTERRUPT 4
168 #define ENDPOINT_C_INTERRUPT 3
169 #define ENDPOINT_B_INTERRUPT 2
170 #define ENDPOINT_A_INTERRUPT 1
171 #define ENDPOINT_0_INTERRUPT 0
172 __le32 irqstat1;
173 #define POWER_STATE_CHANGE_INTERRUPT 27
174 #define PCI_ARBITER_TIMEOUT_INTERRUPT 26
175 #define PCI_PARITY_ERROR_INTERRUPT 25
176 #define PCI_INTA_INTERRUPT 24
177 #define PCI_PME_INTERRUPT 23
178 #define PCI_SERR_INTERRUPT 22
179 #define PCI_PERR_INTERRUPT 21
180 #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20
181 #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19
182 #define PCI_RETRY_ABORT_INTERRUPT 17
183 #define PCI_MASTER_CYCLE_DONE_INTERRUPT 16
184 #define GPIO_INTERRUPT 13
185 #define DMA_D_INTERRUPT 12
186 #define DMA_C_INTERRUPT 11
187 #define DMA_B_INTERRUPT 10
188 #define DMA_A_INTERRUPT 9
189 #define EEPROM_DONE_INTERRUPT 8
190 #define VBUS_INTERRUPT 7
191 #define CONTROL_STATUS_INTERRUPT 6
192 #define ROOT_PORT_RESET_INTERRUPT 4
193 #define SUSPEND_REQUEST_INTERRUPT 3
194 #define SUSPEND_REQUEST_CHANGE_INTERRUPT 2
195 #define RESUME_INTERRUPT 1
196 #define SOF_INTERRUPT 0
197 // offset 0x0030
198 __le32 idxaddr;
199 __le32 idxdata;
200 __le32 fifoctl;
201 #define PCI_BASE2_RANGE 16
202 #define IGNORE_FIFO_AVAILABILITY 3
203 #define PCI_BASE2_SELECT 2
204 #define FIFO_CONFIGURATION_SELECT 0
205 u32 _unused2;
206 // offset 0x0040
207 __le32 memaddr;
208 #define START 28
209 #define DIRECTION 27
210 #define FIFO_DIAGNOSTIC_SELECT 24
211 #define MEMORY_ADDRESS 0
212 __le32 memdata0;
213 __le32 memdata1;
214 u32 _unused3;
215 // offset 0x0050
216 __le32 gpioctl;
217 #define GPIO3_LED_SELECT 12
218 #define GPIO3_INTERRUPT_ENABLE 11
219 #define GPIO2_INTERRUPT_ENABLE 10
220 #define GPIO1_INTERRUPT_ENABLE 9
221 #define GPIO0_INTERRUPT_ENABLE 8
222 #define GPIO3_OUTPUT_ENABLE 7
223 #define GPIO2_OUTPUT_ENABLE 6
224 #define GPIO1_OUTPUT_ENABLE 5
225 #define GPIO0_OUTPUT_ENABLE 4
226 #define GPIO3_DATA 3
227 #define GPIO2_DATA 2
228 #define GPIO1_DATA 1
229 #define GPIO0_DATA 0
230 __le32 gpiostat;
231 #define GPIO3_INTERRUPT 3
232 #define GPIO2_INTERRUPT 2
233 #define GPIO1_INTERRUPT 1
234 #define GPIO0_INTERRUPT 0
235 } __attribute__ ((packed));
237 /* usb control, BAR0 + 0x0080 */
238 struct net2280_usb_regs {
239 // offset 0x0080
240 __le32 stdrsp;
241 #define STALL_UNSUPPORTED_REQUESTS 31
242 #define SET_TEST_MODE 16
243 #define GET_OTHER_SPEED_CONFIGURATION 15
244 #define GET_DEVICE_QUALIFIER 14
245 #define SET_ADDRESS 13
246 #define ENDPOINT_SET_CLEAR_HALT 12
247 #define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11
248 #define GET_STRING_DESCRIPTOR_2 10
249 #define GET_STRING_DESCRIPTOR_1 9
250 #define GET_STRING_DESCRIPTOR_0 8
251 #define GET_SET_INTERFACE 6
252 #define GET_SET_CONFIGURATION 5
253 #define GET_CONFIGURATION_DESCRIPTOR 4
254 #define GET_DEVICE_DESCRIPTOR 3
255 #define GET_ENDPOINT_STATUS 2
256 #define GET_INTERFACE_STATUS 1
257 #define GET_DEVICE_STATUS 0
258 __le32 prodvendid;
259 #define PRODUCT_ID 16
260 #define VENDOR_ID 0
261 __le32 relnum;
262 __le32 usbctl;
263 #define SERIAL_NUMBER_INDEX 16
264 #define PRODUCT_ID_STRING_ENABLE 13
265 #define VENDOR_ID_STRING_ENABLE 12
266 #define USB_ROOT_PORT_WAKEUP_ENABLE 11
267 #define VBUS_PIN 10
268 #define TIMED_DISCONNECT 9
269 #define SUSPEND_IMMEDIATELY 7
270 #define SELF_POWERED_USB_DEVICE 6
271 #define REMOTE_WAKEUP_SUPPORT 5
272 #define PME_POLARITY 4
273 #define USB_DETECT_ENABLE 3
274 #define PME_WAKEUP_ENABLE 2
275 #define DEVICE_REMOTE_WAKEUP_ENABLE 1
276 #define SELF_POWERED_STATUS 0
277 // offset 0x0090
278 __le32 usbstat;
279 #define HIGH_SPEED 7
280 #define FULL_SPEED 6
281 #define GENERATE_RESUME 5
282 #define GENERATE_DEVICE_REMOTE_WAKEUP 4
283 __le32 xcvrdiag;
284 #define FORCE_HIGH_SPEED_MODE 31
285 #define FORCE_FULL_SPEED_MODE 30
286 #define USB_TEST_MODE 24
287 #define LINE_STATE 16
288 #define TRANSCEIVER_OPERATION_MODE 2
289 #define TRANSCEIVER_SELECT 1
290 #define TERMINATION_SELECT 0
291 __le32 setup0123;
292 __le32 setup4567;
293 // offset 0x0090
294 u32 _unused0;
295 __le32 ouraddr;
296 #define FORCE_IMMEDIATE 7
297 #define OUR_USB_ADDRESS 0
298 __le32 ourconfig;
299 } __attribute__ ((packed));
301 /* pci control, BAR0 + 0x0100 */
302 struct net2280_pci_regs {
303 // offset 0x0100
304 __le32 pcimstctl;
305 #define PCI_ARBITER_PARK_SELECT 13
306 #define PCI_MULTI LEVEL_ARBITER 12
307 #define PCI_RETRY_ABORT_ENABLE 11
308 #define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10
309 #define DMA_READ_MULTIPLE_ENABLE 9
310 #define DMA_READ_LINE_ENABLE 8
311 #define PCI_MASTER_COMMAND_SELECT 6
312 #define MEM_READ_OR_WRITE 0
313 #define IO_READ_OR_WRITE 1
314 #define CFG_READ_OR_WRITE 2
315 #define PCI_MASTER_START 5
316 #define PCI_MASTER_READ_WRITE 4
317 #define PCI_MASTER_WRITE 0
318 #define PCI_MASTER_READ 1
319 #define PCI_MASTER_BYTE_WRITE_ENABLES 0
320 __le32 pcimstaddr;
321 __le32 pcimstdata;
322 __le32 pcimststat;
323 #define PCI_ARBITER_CLEAR 2
324 #define PCI_EXTERNAL_ARBITER 1
325 #define PCI_HOST_MODE 0
326 } __attribute__ ((packed));
328 /* dma control, BAR0 + 0x0180 ... array of four structs like this,
329 * for channels 0..3. see also struct net2280_dma: descriptor
330 * that can be loaded into some of these registers.
332 struct net2280_dma_regs { /* [11.7] */
333 // offset 0x0180, 0x01a0, 0x01c0, 0x01e0,
334 __le32 dmactl;
335 #define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25
336 #define DMA_CLEAR_COUNT_ENABLE 21
337 #define DESCRIPTOR_POLLING_RATE 19
338 #define POLL_CONTINUOUS 0
339 #define POLL_1_USEC 1
340 #define POLL_100_USEC 2
341 #define POLL_1_MSEC 3
342 #define DMA_VALID_BIT_POLLING_ENABLE 18
343 #define DMA_VALID_BIT_ENABLE 17
344 #define DMA_SCATTER_GATHER_ENABLE 16
345 #define DMA_OUT_AUTO_START_ENABLE 4
346 #define DMA_PREEMPT_ENABLE 3
347 #define DMA_FIFO_VALIDATE 2
348 #define DMA_ENABLE 1
349 #define DMA_ADDRESS_HOLD 0
350 __le32 dmastat;
351 #define DMA_SCATTER_GATHER_DONE_INTERRUPT 25
352 #define DMA_TRANSACTION_DONE_INTERRUPT 24
353 #define DMA_ABORT 1
354 #define DMA_START 0
355 u32 _unused0[2];
356 // offset 0x0190, 0x01b0, 0x01d0, 0x01f0,
357 __le32 dmacount;
358 #define VALID_BIT 31
359 #define DMA_DIRECTION 30
360 #define DMA_DONE_INTERRUPT_ENABLE 29
361 #define END_OF_CHAIN 28
362 #define DMA_BYTE_COUNT_MASK ((1<<24)-1)
363 #define DMA_BYTE_COUNT 0
364 __le32 dmaaddr;
365 __le32 dmadesc;
366 u32 _unused1;
367 } __attribute__ ((packed));
369 /* dedicated endpoint registers, BAR0 + 0x0200 */
371 struct net2280_dep_regs { /* [11.8] */
372 // offset 0x0200, 0x0210, 0x220, 0x230, 0x240
373 __le32 dep_cfg;
374 // offset 0x0204, 0x0214, 0x224, 0x234, 0x244
375 __le32 dep_rsp;
376 u32 _unused[2];
377 } __attribute__ ((packed));
379 /* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
380 * like this, for ep0 then the configurable endpoints A..F
381 * ep0 reserved for control; E and F have only 64 bytes of fifo
383 struct net2280_ep_regs { /* [11.9] */
384 // offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0
385 __le32 ep_cfg;
386 #define ENDPOINT_BYTE_COUNT 16
387 #define ENDPOINT_ENABLE 10
388 #define ENDPOINT_TYPE 8
389 #define ENDPOINT_DIRECTION 7
390 #define ENDPOINT_NUMBER 0
391 __le32 ep_rsp;
392 #define SET_NAK_OUT_PACKETS 15
393 #define SET_EP_HIDE_STATUS_PHASE 14
394 #define SET_EP_FORCE_CRC_ERROR 13
395 #define SET_INTERRUPT_MODE 12
396 #define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11
397 #define SET_NAK_OUT_PACKETS_MODE 10
398 #define SET_ENDPOINT_TOGGLE 9
399 #define SET_ENDPOINT_HALT 8
400 #define CLEAR_NAK_OUT_PACKETS 7
401 #define CLEAR_EP_HIDE_STATUS_PHASE 6
402 #define CLEAR_EP_FORCE_CRC_ERROR 5
403 #define CLEAR_INTERRUPT_MODE 4
404 #define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3
405 #define CLEAR_NAK_OUT_PACKETS_MODE 2
406 #define CLEAR_ENDPOINT_TOGGLE 1
407 #define CLEAR_ENDPOINT_HALT 0
408 __le32 ep_irqenb;
409 #define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6
410 #define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5
411 #define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3
412 #define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2
413 #define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1
414 #define DATA_IN_TOKEN_INTERRUPT_ENABLE 0
415 __le32 ep_stat;
416 #define FIFO_VALID_COUNT 24
417 #define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22
418 #define TIMEOUT 21
419 #define USB_STALL_SENT 20
420 #define USB_IN_NAK_SENT 19
421 #define USB_IN_ACK_RCVD 18
422 #define USB_OUT_PING_NAK_SENT 17
423 #define USB_OUT_ACK_SENT 16
424 #define FIFO_OVERFLOW 13
425 #define FIFO_UNDERFLOW 12
426 #define FIFO_FULL 11
427 #define FIFO_EMPTY 10
428 #define FIFO_FLUSH 9
429 #define SHORT_PACKET_OUT_DONE_INTERRUPT 6
430 #define SHORT_PACKET_TRANSFERRED_INTERRUPT 5
431 #define NAK_OUT_PACKETS 4
432 #define DATA_PACKET_RECEIVED_INTERRUPT 3
433 #define DATA_PACKET_TRANSMITTED_INTERRUPT 2
434 #define DATA_OUT_PING_TOKEN_INTERRUPT 1
435 #define DATA_IN_TOKEN_INTERRUPT 0
436 // offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0
437 __le32 ep_avail;
438 __le32 ep_data;
439 u32 _unused0[2];
440 } __attribute__ ((packed));
442 struct net2280_reg_write {
443 __le16 port;
444 __le32 addr;
445 __le32 val;
446 } __attribute__ ((packed));
448 struct net2280_reg_read {
449 __le16 port;
450 __le32 addr;
451 } __attribute__ ((packed));
452 #endif /* NET2280_H */