libata pata_via: ACPI checks for 80wire cable

[pv_ops_mirror.git] / drivers / ide / pci / it821x.c

/*
 * linux/drivers/ide/pci/it821x.c               Version 0.16    Jul 3 2007
 *
 * Copyright (C) 2004           Red Hat <alan@redhat.com>
 * Copyright (C) 2007           Bartlomiej Zolnierkiewicz
 *
 *  May be copied or modified under the terms of the GNU General Public License
 *  Based in part on the ITE vendor provided SCSI driver.
 *
 *  Documentation available from
 *      http://www.ite.com.tw/pc/IT8212F_V04.pdf
 *  Some other documents are NDA.
 *
 *  The ITE8212 isn't exactly a standard IDE controller. It has two
 *  modes. In pass through mode then it is an IDE controller. In its smart
 *  mode its actually quite a capable hardware raid controller disguised
 *  as an IDE controller. Smart mode only understands DMA read/write and
 *  identify, none of the fancier commands apply. The IT8211 is identical
 *  in other respects but lacks the raid mode.
 *
 *  Errata:
 *  o   Rev 0x10 also requires master/slave hold the same DMA timings and
 *      cannot do ATAPI MWDMA.
 *  o   The identify data for raid volumes lacks CHS info (technically ok)
 *      but also fails to set the LBA28 and other bits. We fix these in
 *      the IDE probe quirk code.
 *  o   If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
 *      raid then the controller firmware dies
 *  o   Smart mode without RAID doesn't clear all the necessary identify
 *      bits to reduce the command set to the one used
 *
 *  This has a few impacts on the driver
 *  - In pass through mode we do all the work you would expect
 *  - In smart mode the clocking set up is done by the controller generally
 *    but we must watch the other limits and filter.
 *  - There are a few extra vendor commands that actually talk to the
 *    controller but only work PIO with no IRQ.
 *
 *  Vendor areas of the identify block in smart mode are used for the
 *  timing and policy set up. Each HDD in raid mode also has a serial
 *  block on the disk. The hardware extra commands are get/set chip status,
 *  rebuild, get rebuild status.
 *
 *  In Linux the driver supports pass through mode as if the device was
 *  just another IDE controller. If the smart mode is running then
 *  volumes are managed by the controller firmware and each IDE "disk"
 *  is a raid volume. Even more cute - the controller can do automated
 *  hotplug and rebuild.
 *
 *  The pass through controller itself is a little demented. It has a
 *  flaw that it has a single set of PIO/MWDMA timings per channel so
 *  non UDMA devices restrict each others performance. It also has a
 *  single clock source per channel so mixed UDMA100/133 performance
 *  isn't perfect and we have to pick a clock. Thankfully none of this
 *  matters in smart mode. ATAPI DMA is not currently supported.
 *
 *  It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
 *
 *  TODO
 *      -       ATAPI UDMA is ok but not MWDMA it seems
 *      -       RAID configuration ioctls
 *      -       Move to libata once it grows up
 */

#include <linux/types.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>

#include <asm/io.h>

struct it821x_dev
{
        unsigned int smart:1,           /* Are we in smart raid mode */
                timing10:1;             /* Rev 0x10 */
        u8      clock_mode;             /* 0, ATA_50 or ATA_66 */
        u8      want[2][2];             /* Mode/Pri log for master slave */
        /* We need these for switching the clock when DMA goes on/off
           The high byte is the 66Mhz timing */
        u16     pio[2];                 /* Cached PIO values */
        u16     mwdma[2];               /* Cached MWDMA values */
        u16     udma[2];                /* Cached UDMA values (per drive) */
};

#define ATA_66          0
#define ATA_50          1
#define ATA_ANY         2

#define UDMA_OFF        0
#define MWDMA_OFF       0

/*
 *      We allow users to force the card into non raid mode without
 *      flashing the alternative BIOS. This is also neccessary right now
 *      for embedded platforms that cannot run a PC BIOS but are using this
 *      device.
 */

static int it8212_noraid;

/**
 *      it821x_program  -       program the PIO/MWDMA registers
 *      @drive: drive to tune
 *      @timing: timing info
 *
 *      Program the PIO/MWDMA timing for this channel according to the
 *      current clock.
 */

static void it821x_program(ide_drive_t *drive, u16 timing)
{
        ide_hwif_t *hwif        = drive->hwif;
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);
        int channel = hwif->channel;
        u8 conf;

        /* Program PIO/MWDMA timing bits */
        if(itdev->clock_mode == ATA_66)
                conf = timing >> 8;
        else
                conf = timing & 0xFF;
        pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * channel, conf);
}

/**
 *      it821x_program_udma     -       program the UDMA registers
 *      @drive: drive to tune
 *      @timing: timing info
 *
 *      Program the UDMA timing for this drive according to the
 *      current clock.
 */

static void it821x_program_udma(ide_drive_t *drive, u16 timing)
{
        ide_hwif_t *hwif        = drive->hwif;
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);
        int channel = hwif->channel;
        int unit = drive->select.b.unit;
        u8 conf;

        /* Program UDMA timing bits */
        if(itdev->clock_mode == ATA_66)
                conf = timing >> 8;
        else
                conf = timing & 0xFF;
        if(itdev->timing10 == 0)
                pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + unit, conf);
        else {
                pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel, conf);
                pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + 1, conf);
        }
}

/**
 *      it821x_clock_strategy
 *      @drive: drive to set up
 *
 *      Select between the 50 and 66Mhz base clocks to get the best
 *      results for this interface.
 */

static void it821x_clock_strategy(ide_drive_t *drive)
{
        ide_hwif_t *hwif = drive->hwif;
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);

        u8 unit = drive->select.b.unit;
        ide_drive_t *pair = &hwif->drives[1-unit];

        int clock, altclock;
        u8 v;
        int sel = 0;

        if(itdev->want[0][0] > itdev->want[1][0]) {
                clock = itdev->want[0][1];
                altclock = itdev->want[1][1];
        } else {
                clock = itdev->want[1][1];
                altclock = itdev->want[0][1];
        }

        /*
         * if both clocks can be used for the mode with the higher priority
         * use the clock needed by the mode with the lower priority
         */
        if (clock == ATA_ANY)
                clock = altclock;

        /* Nobody cares - keep the same clock */
        if(clock == ATA_ANY)
                return;
        /* No change */
        if(clock == itdev->clock_mode)
                return;

        /* Load this into the controller ? */
        if(clock == ATA_66)
                itdev->clock_mode = ATA_66;
        else {
                itdev->clock_mode = ATA_50;
                sel = 1;
        }
        pci_read_config_byte(hwif->pci_dev, 0x50, &v);
        v &= ~(1 << (1 + hwif->channel));
        v |= sel << (1 + hwif->channel);
        pci_write_config_byte(hwif->pci_dev, 0x50, v);

        /*
         *      Reprogram the UDMA/PIO of the pair drive for the switch
         *      MWDMA will be dealt with by the dma switcher
         */
        if(pair && itdev->udma[1-unit] != UDMA_OFF) {
                it821x_program_udma(pair, itdev->udma[1-unit]);
                it821x_program(pair, itdev->pio[1-unit]);
        }
        /*
         *      Reprogram the UDMA/PIO of our drive for the switch.
         *      MWDMA will be dealt with by the dma switcher
         */
        if(itdev->udma[unit] != UDMA_OFF) {
                it821x_program_udma(drive, itdev->udma[unit]);
                it821x_program(drive, itdev->pio[unit]);
        }
}

/**
 *      it821x_tunepio  -       tune a drive
 *      @drive: drive to tune
 *      @pio: the desired PIO mode
 *
 *      Try to tune the drive/host to the desired PIO mode taking into
 *      the consideration the maximum PIO mode supported by the other
 *      device on the cable.
 */

static int it821x_tunepio(ide_drive_t *drive, u8 set_pio)
{
        ide_hwif_t *hwif        = drive->hwif;
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);
        int unit = drive->select.b.unit;
        ide_drive_t *pair = &hwif->drives[1 - unit];

        /* Spec says 89 ref driver uses 88 */
        static u16 pio[]        = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
        static u8 pio_want[]    = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };

        /*
         * Compute the best PIO mode we can for a given device. We must
         * pick a speed that does not cause problems with the other device
         * on the cable.
         */
        if (pair) {
                u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4);
                /* trim PIO to the slowest of the master/slave */
                if (pair_pio < set_pio)
                        set_pio = pair_pio;
        }

        if (itdev->smart)
                return 0;

        /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
        itdev->want[unit][1] = pio_want[set_pio];
        itdev->want[unit][0] = 1;       /* PIO is lowest priority */
        itdev->pio[unit] = pio[set_pio];
        it821x_clock_strategy(drive);
        it821x_program(drive, itdev->pio[unit]);

        return ide_config_drive_speed(drive, XFER_PIO_0 + set_pio);
}

static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
        (void)it821x_tunepio(drive, pio);
}

/**
 *      it821x_tune_mwdma       -       tune a channel for MWDMA
 *      @drive: drive to set up
 *      @mode_wanted: the target operating mode
 *
 *      Load the timing settings for this device mode into the
 *      controller when doing MWDMA in pass through mode. The caller
 *      must manage the whole lack of per device MWDMA/PIO timings and
 *      the shared MWDMA/PIO timing register.
 */

static void it821x_tune_mwdma (ide_drive_t *drive, byte mode_wanted)
{
        ide_hwif_t *hwif        = drive->hwif;
        struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif);
        int unit = drive->select.b.unit;
        int channel = hwif->channel;
        u8 conf;

        static u16 dma[]        = { 0x8866, 0x3222, 0x3121 };
        static u8 mwdma_want[]  = { ATA_ANY, ATA_66, ATA_ANY };

        itdev->want[unit][1] = mwdma_want[mode_wanted];
        itdev->want[unit][0] = 2;       /* MWDMA is low priority */
        itdev->mwdma[unit] = dma[mode_wanted];
        itdev->udma[unit] = UDMA_OFF;

        /* UDMA bits off - Revision 0x10 do them in pairs */
        pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
        if(itdev->timing10)
                conf |= channel ? 0x60: 0x18;
        else
                conf |= 1 << (3 + 2 * channel + unit);
        pci_write_config_byte(hwif->pci_dev, 0x50, conf);

        it821x_clock_strategy(drive);
        /* FIXME: do we need to program this ? */
        /* it821x_program(drive, itdev->mwdma[unit]); */
}

/**
 *      it821x_tune_udma        -       tune a channel for UDMA
 *      @drive: drive to set up
 *      @mode_wanted: the target operating mode
 *
 *      Load the timing settings for this device mode into the
 *      controller when doing UDMA modes in pass through.
 */

static void it821x_tune_udma (ide_drive_t *drive, byte mode_wanted)
{
        ide_hwif_t *hwif        = drive->hwif;
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);
        int unit = drive->select.b.unit;
        int channel = hwif->channel;
        u8 conf;

        static u16 udma[]       = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
        static u8 udma_want[]   = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };

        itdev->want[unit][1] = udma_want[mode_wanted];
        itdev->want[unit][0] = 3;       /* UDMA is high priority */
        itdev->mwdma[unit] = MWDMA_OFF;
        itdev->udma[unit] = udma[mode_wanted];
        if(mode_wanted >= 5)
                itdev->udma[unit] |= 0x8080;    /* UDMA 5/6 select on */

        /* UDMA on. Again revision 0x10 must do the pair */
        pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
        if(itdev->timing10)
                conf &= channel ? 0x9F: 0xE7;
        else
                conf &= ~ (1 << (3 + 2 * channel + unit));
        pci_write_config_byte(hwif->pci_dev, 0x50, conf);

        it821x_clock_strategy(drive);
        it821x_program_udma(drive, itdev->udma[unit]);

}

/**
 *      it821x_dma_read -       DMA hook
 *      @drive: drive for DMA
 *
 *      The IT821x has a single timing register for MWDMA and for PIO
 *      operations. As we flip back and forth we have to reload the
 *      clock. In addition the rev 0x10 device only works if the same
 *      timing value is loaded into the master and slave UDMA clock
 *      so we must also reload that.
 *
 *      FIXME: we could figure out in advance if we need to do reloads
 */

static void it821x_dma_start(ide_drive_t *drive)
{
        ide_hwif_t *hwif = drive->hwif;
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);
        int unit = drive->select.b.unit;
        if(itdev->mwdma[unit] != MWDMA_OFF)
                it821x_program(drive, itdev->mwdma[unit]);
        else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10)
                it821x_program_udma(drive, itdev->udma[unit]);
        ide_dma_start(drive);
}

/**
 *      it821x_dma_write        -       DMA hook
 *      @drive: drive for DMA stop
 *
 *      The IT821x has a single timing register for MWDMA and for PIO
 *      operations. As we flip back and forth we have to reload the
 *      clock.
 */

static int it821x_dma_end(ide_drive_t *drive)
{
        ide_hwif_t *hwif = drive->hwif;
        int unit = drive->select.b.unit;
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);
        int ret = __ide_dma_end(drive);
        if(itdev->mwdma[unit] != MWDMA_OFF)
                it821x_program(drive, itdev->pio[unit]);
        return ret;
}

/**
 *      it821x_tune_chipset     -       set controller timings
 *      @drive: Drive to set up
 *      @speed: speed we want to achieve
 *
 *      Tune the ITE chipset for the desired mode.
 */

static int it821x_tune_chipset(ide_drive_t *drive, const u8 speed)
{

        ide_hwif_t *hwif        = drive->hwif;
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);

        if (itdev->smart == 0) {
                switch (speed) {
                        /* MWDMA tuning is really hard because our MWDMA and PIO
                           timings are kept in the same place. We can switch in the
                           host dma on/off callbacks */
                        case XFER_MW_DMA_2:
                        case XFER_MW_DMA_1:
                        case XFER_MW_DMA_0:
                                it821x_tune_mwdma(drive, (speed - XFER_MW_DMA_0));
                                break;
                        case XFER_UDMA_6:
                        case XFER_UDMA_5:
                        case XFER_UDMA_4:
                        case XFER_UDMA_3:
                        case XFER_UDMA_2:
                        case XFER_UDMA_1:
                        case XFER_UDMA_0:
                                it821x_tune_udma(drive, (speed - XFER_UDMA_0));
                                break;
                        default:
                                return 1;
                }

                return ide_config_drive_speed(drive, speed);
        }

        /* don't touch anything in the smart mode */
        return 0;
}

/**
 *      it821x_configure_drive_for_dma  -       set up for DMA transfers
 *      @drive: drive we are going to set up
 *
 *      Set up the drive for DMA, tune the controller and drive as
 *      required. If the drive isn't suitable for DMA or we hit
 *      other problems then we will drop down to PIO and set up
 *      PIO appropriately
 */

static int it821x_config_drive_for_dma (ide_drive_t *drive)
{
        if (ide_tune_dma(drive))
                return 0;

        ide_set_max_pio(drive);

        return -1;
}

/**
 *      ata66_it821x    -       check for 80 pin cable
 *      @hwif: interface to check
 *
 *      Check for the presence of an ATA66 capable cable on the
 *      interface. Problematic as it seems some cards don't have
 *      the needed logic onboard.
 */

static u8 __devinit ata66_it821x(ide_hwif_t *hwif)
{
        /* The reference driver also only does disk side */
        return ATA_CBL_PATA80;
}

/**
 *      it821x_fixup    -       post init callback
 *      @hwif: interface
 *
 *      This callback is run after the drives have been probed but
 *      before anything gets attached. It allows drivers to do any
 *      final tuning that is needed, or fixups to work around bugs.
 */

static void __devinit it821x_fixups(ide_hwif_t *hwif)
{
        struct it821x_dev *itdev = ide_get_hwifdata(hwif);
        int i;

        if(!itdev->smart) {
                /*
                 *      If we are in pass through mode then not much
                 *      needs to be done, but we do bother to clear the
                 *      IRQ mask as we may well be in PIO (eg rev 0x10)
                 *      for now and we know unmasking is safe on this chipset.
                 */
                for (i = 0; i < 2; i++) {
                        ide_drive_t *drive = &hwif->drives[i];
                        if(drive->present)
                                drive->unmask = 1;
                }
                return;
        }
        /*
         *      Perform fixups on smart mode. We need to "lose" some
         *      capabilities the firmware lacks but does not filter, and
         *      also patch up some capability bits that it forgets to set
         *      in RAID mode.
         */

        for(i = 0; i < 2; i++) {
                ide_drive_t *drive = &hwif->drives[i];
                struct hd_driveid *id;
                u16 *idbits;

                if(!drive->present)
                        continue;
                id = drive->id;
                idbits = (u16 *)drive->id;

                /* Check for RAID v native */
                if(strstr(id->model, "Integrated Technology Express")) {
                        /* In raid mode the ident block is slightly buggy
                           We need to set the bits so that the IDE layer knows
                           LBA28. LBA48 and DMA ar valid */
                        id->capability |= 3;            /* LBA28, DMA */
                        id->command_set_2 |= 0x0400;    /* LBA48 valid */
                        id->cfs_enable_2 |= 0x0400;     /* LBA48 on */
                        /* Reporting logic */
                        printk(KERN_INFO "%s: IT8212 %sRAID %d volume",
                                drive->name,
                                idbits[147] ? "Bootable ":"",
                                idbits[129]);
                                if(idbits[129] != 1)
                                        printk("(%dK stripe)", idbits[146]);
                                printk(".\n");
                } else {
                        /* Non RAID volume. Fixups to stop the core code
                           doing unsupported things */
                        id->field_valid &= 3;
                        id->queue_depth = 0;
                        id->command_set_1 = 0;
                        id->command_set_2 &= 0xC400;
                        id->cfsse &= 0xC000;
                        id->cfs_enable_1 = 0;
                        id->cfs_enable_2 &= 0xC400;
                        id->csf_default &= 0xC000;
                        id->word127 = 0;
                        id->dlf = 0;
                        id->csfo = 0;
                        id->cfa_power = 0;
                        printk(KERN_INFO "%s: Performing identify fixups.\n",
                                drive->name);
                }

                /*
                 * Set MWDMA0 mode as enabled/support - just to tell
                 * IDE core that DMA is supported (it821x hardware
                 * takes care of DMA mode programming).
                 */
                if (id->capability & 1) {
                        id->dma_mword |= 0x0101;
                        drive->current_speed = XFER_MW_DMA_0;
                }
        }

}

/**
 *      init_hwif_it821x        -       set up hwif structs
 *      @hwif: interface to set up
 *
 *      We do the basic set up of the interface structure. The IT8212
 *      requires several custom handlers so we override the default
 *      ide DMA handlers appropriately
 */

static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
{
        struct it821x_dev *idev = kzalloc(sizeof(struct it821x_dev), GFP_KERNEL);
        u8 conf;

        if(idev == NULL) {
                printk(KERN_ERR "it821x: out of memory, falling back to legacy behaviour.\n");
                goto fallback;
        }
        ide_set_hwifdata(hwif, idev);

        hwif->atapi_dma = 1;

        pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
        if(conf & 1) {
                idev->smart = 1;
                hwif->atapi_dma = 0;
                /* Long I/O's although allowed in LBA48 space cause the
                   onboard firmware to enter the twighlight zone */
                hwif->rqsize = 256;
        }

        /* Pull the current clocks from 0x50 also */
        if (conf & (1 << (1 + hwif->channel)))
                idev->clock_mode = ATA_50;
        else
                idev->clock_mode = ATA_66;

        idev->want[0][1] = ATA_ANY;
        idev->want[1][1] = ATA_ANY;

        /*
         *      Not in the docs but according to the reference driver
         *      this is neccessary.
         */

        pci_read_config_byte(hwif->pci_dev, 0x08, &conf);
        if(conf == 0x10) {
                idev->timing10 = 1;
                hwif->atapi_dma = 0;
                if(!idev->smart)
                        printk(KERN_WARNING "it821x: Revision 0x10, workarounds activated.\n");
        }

        hwif->speedproc = &it821x_tune_chipset;
        hwif->set_pio_mode = &it821x_set_pio_mode;

        /* MWDMA/PIO clock switching for pass through mode */
        if(!idev->smart) {
                hwif->dma_start = &it821x_dma_start;
                hwif->ide_dma_end = &it821x_dma_end;
        }

        hwif->drives[0].autotune = 1;
        hwif->drives[1].autotune = 1;

        if (!hwif->dma_base)
                goto fallback;

        hwif->ultra_mask = 0x7f;
        hwif->mwdma_mask = 0x07;

        hwif->ide_dma_check = &it821x_config_drive_for_dma;

        if (hwif->cbl != ATA_CBL_PATA40_SHORT)
                hwif->cbl = ata66_it821x(hwif);

        /*
         *      The BIOS often doesn't set up DMA on this controller
         *      so we always do it.
         */

        hwif->autodma = 1;
        hwif->drives[0].autodma = hwif->autodma;
        hwif->drives[1].autodma = hwif->autodma;
        return;
fallback:
        hwif->autodma = 0;
        return;
}

static void __devinit it8212_disable_raid(struct pci_dev *dev)
{
        /* Reset local CPU, and set BIOS not ready */
        pci_write_config_byte(dev, 0x5E, 0x01);

        /* Set to bypass mode, and reset PCI bus */
        pci_write_config_byte(dev, 0x50, 0x00);
        pci_write_config_word(dev, PCI_COMMAND,
                              PCI_COMMAND_PARITY | PCI_COMMAND_IO |
                              PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
        pci_write_config_word(dev, 0x40, 0xA0F3);

        pci_write_config_dword(dev,0x4C, 0x02040204);
        pci_write_config_byte(dev, 0x42, 0x36);
        pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
}

static unsigned int __devinit init_chipset_it821x(struct pci_dev *dev, const char *name)
{
        u8 conf;
        static char *mode[2] = { "pass through", "smart" };

        /* Force the card into bypass mode if so requested */
        if (it8212_noraid) {
                printk(KERN_INFO "it8212: forcing bypass mode.\n");
                it8212_disable_raid(dev);
        }
        pci_read_config_byte(dev, 0x50, &conf);
        printk(KERN_INFO "it821x: controller in %s mode.\n", mode[conf & 1]);
        return 0;
}


#define DECLARE_ITE_DEV(name_str)                       \
        {                                               \
                .name           = name_str,             \
                .init_chipset   = init_chipset_it821x,  \
                .init_hwif      = init_hwif_it821x,     \
                .autodma        = AUTODMA,              \
                .bootable       = ON_BOARD,             \
                .fixup          = it821x_fixups,        \
                .pio_mask       = ATA_PIO4,             \
        }

static ide_pci_device_t it821x_chipsets[] __devinitdata = {
        /* 0 */ DECLARE_ITE_DEV("IT8212"),
};

/**
 *      it821x_init_one -       pci layer discovery entry
 *      @dev: PCI device
 *      @id: ident table entry
 *
 *      Called by the PCI code when it finds an ITE821x controller.
 *      We then use the IDE PCI generic helper to do most of the work.
 */

static int __devinit it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
        ide_setup_pci_device(dev, &it821x_chipsets[id->driver_data]);
        return 0;
}

static struct pci_device_id it821x_pci_tbl[] = {
        { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
        { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
        { 0, },
};

MODULE_DEVICE_TABLE(pci, it821x_pci_tbl);

static struct pci_driver driver = {
        .name           = "ITE821x IDE",
        .id_table       = it821x_pci_tbl,
        .probe          = it821x_init_one,
};

static int __init it821x_ide_init(void)
{
        return ide_pci_register_driver(&driver);
}

module_init(it821x_ide_init);

module_param_named(noraid, it8212_noraid, int, S_IRUGO);
MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode");

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("PCI driver module for the ITE 821x");
MODULE_LICENSE("GPL");