arch/sh/boards/se/7751/pci.c

   1 /*
   2  * linux/arch/sh/boards/se/7751/pci.c
   3  *
   4  * Author:  Ian DaSilva (idasilva@mvista.com)
   5  *
   6  * Highly leveraged from pci-bigsur.c, written by Dustin McIntire.
   7  *
   8  * May be copied or modified under the terms of the GNU General Public
   9  * License.  See linux/COPYING for more information.
  10  *
  11  * PCI initialization for the Hitachi SH7751 Solution Engine board (MS7751SE01)
  12  */
  13
  14 #include <linux/kernel.h>
  15 #include <linux/types.h>
  16 #include <linux/init.h>
  17 #include <linux/delay.h>
  18 #include <linux/pci.h>
  19
  20 #include <asm/io.h>
  21 #include "../../../drivers/pci/pci-sh7751.h"
  22
  23 #define PCIMCR_MRSET_OFF        0xBFFFFFFF
  24 #define PCIMCR_RFSH_OFF         0xFFFFFFFB
  25
  26 /*
  27  * Only long word accesses of the PCIC's internal local registers and the
  28  * configuration registers from the CPU is supported.
  29  */
  30 #define PCIC_WRITE(x,v) writel((v), PCI_REG(x))
  31 #define PCIC_READ(x) readl(PCI_REG(x))
  32
  33 /*
  34  * Description:  This function sets up and initializes the pcic, sets
  35  * up the BARS, maps the DRAM into the address space etc, etc.
  36  */
  37 int __init pcibios_init_platform(void)
  38 {
  39    unsigned long bcr1, wcr1, wcr2, wcr3, mcr;
  40    unsigned short bcr2;
  41
  42    /*
  43     * Initialize the slave bus controller on the pcic.  The values used
  44     * here should not be hardcoded, but they should be taken from the bsc
  45     * on the processor, to make this function as generic as possible.
  46     * (i.e. Another sbc may usr different SDRAM timing settings -- in order
  47     * for the pcic to work, its settings need to be exactly the same.)
  48     */
  49    bcr1 = (*(volatile unsigned long*)(SH7751_BCR1));
  50    bcr2 = (*(volatile unsigned short*)(SH7751_BCR2));
  51    wcr1 = (*(volatile unsigned long*)(SH7751_WCR1));
  52    wcr2 = (*(volatile unsigned long*)(SH7751_WCR2));
  53    wcr3 = (*(volatile unsigned long*)(SH7751_WCR3));
  54    mcr = (*(volatile unsigned long*)(SH7751_MCR));
  55
  56    bcr1 = bcr1 | 0x00080000;  /* Enable Bit 19, BREQEN */
  57    (*(volatile unsigned long*)(SH7751_BCR1)) = bcr1;
  58
  59    bcr1 = bcr1 | 0x40080000;  /* Enable Bit 19 BREQEN, set PCIC to slave */
  60    PCIC_WRITE(SH7751_PCIBCR1, bcr1);     /* PCIC BCR1 */
  61    PCIC_WRITE(SH7751_PCIBCR2, bcr2);     /* PCIC BCR2 */
  62    PCIC_WRITE(SH7751_PCIWCR1, wcr1);     /* PCIC WCR1 */
  63    PCIC_WRITE(SH7751_PCIWCR2, wcr2);     /* PCIC WCR2 */
  64    PCIC_WRITE(SH7751_PCIWCR3, wcr3);     /* PCIC WCR3 */
  65    mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF;
  66    PCIC_WRITE(SH7751_PCIMCR, mcr);      /* PCIC MCR */
  67
  68
  69    /* Enable all interrupts, so we know what to fix */
  70    PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff);
  71    PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f);
  72
  73    /* Set up standard PCI config registers */
  74    PCIC_WRITE(SH7751_PCICONF1,  0xF39000C7); /* Bus Master, Mem & I/O access */
  75    PCIC_WRITE(SH7751_PCICONF2,  0x00000000); /* PCI Class code & Revision ID */
  76    PCIC_WRITE(SH7751_PCICONF4,  0xab000001); /* PCI I/O address (local regs) */
  77    PCIC_WRITE(SH7751_PCICONF5,  0x0c000000); /* PCI MEM address (local RAM)  */
  78    PCIC_WRITE(SH7751_PCICONF6,  0xd0000000); /* PCI MEM address (unused)     */
  79    PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */
  80    PCIC_WRITE(SH7751_PCILSR0, 0x03f00000);   /* MEM (full 64M exposed)       */
  81    PCIC_WRITE(SH7751_PCILSR1, 0x00000000);   /* MEM (unused)                 */
  82    PCIC_WRITE(SH7751_PCILAR0, 0x0c000000);   /* MEM (direct map from PCI)    */
  83    PCIC_WRITE(SH7751_PCILAR1, 0x00000000);   /* MEM (unused)                 */
  84
  85    /* Now turn it on... */
  86    PCIC_WRITE(SH7751_PCICR, 0xa5000001);
  87
  88    /*
  89     * Set PCIMBR and PCIIOBR here, assuming a single window
  90     * (16M MEM, 256K IO) is enough.  If a larger space is
  91     * needed, the readx/writex and inx/outx functions will
  92     * have to do more (e.g. setting registers for each call).
  93     */
  94
  95    /*
  96     * Set the MBR so PCI address is one-to-one with window,
  97     * meaning all calls go straight through... use BUG_ON to
  98     * catch erroneous assumption.
  99     */
 100    BUG_ON(PCIBIOS_MIN_MEM != SH7751_PCI_MEMORY_BASE);
 101
 102    PCIC_WRITE(SH7751_PCIMBR, PCIBIOS_MIN_MEM);
 103
 104    /* Set IOBR for window containing area specified in pci.h */
 105    PCIC_WRITE(SH7751_PCIIOBR, (PCIBIOS_MIN_IO & SH7751_PCIIOBR_MASK));
 106
 107    /* All done, may as well say so... */
 108    printk("SH7751 PCI: Finished initialization of the PCI controller\n");
 109
 110    return 1;
 111 }
 112
 113 int __init pcibios_map_platform_irq(u8 slot, u8 pin)
 114 {
 115         switch (slot) {
 116         case 0: return 13;
 117         case 1: return 13;      /* AMD Ethernet controller */
 118         case 2: return -1;
 119         case 3: return -1;
 120         case 4: return -1;
 121         default:
 122                 printk("PCI: Bad IRQ mapping request for slot %d\n", slot);
 123                 return -1;
 124         }
 125 }
 126
 127 static struct resource sh7751_io_resource = {
 128         .name   = "SH7751 IO",
 129         .start  = SH7751_PCI_IO_BASE,
 130         .end    = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1,
 131         .flags  = IORESOURCE_IO
 132 };
 133
 134 static struct resource sh7751_mem_resource = {
 135         .name   = "SH7751 mem",
 136         .start  = SH7751_PCI_MEMORY_BASE,
 137         .end    = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1,
 138         .flags  = IORESOURCE_MEM
 139 };
 140
 141 extern struct pci_ops sh7751_pci_ops;
 142
 143 struct pci_channel board_pci_channels[] = {
 144         { &sh7751_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff },
 145         { NULL, NULL, NULL, 0, 0 },
 146 };
 147