ia64/kvm: compilation fix. export account_system_vtime.

[pv_ops_mirror.git] / drivers / ide / pci / cy82c693.c

/*
 *  Copyright (C) 1998-2000 Andreas S. Krebs (akrebs@altavista.net), Maintainer
 *  Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>, Integrator
 *
 * CYPRESS CY82C693 chipset IDE controller
 *
 * The CY82C693 chipset is used on Digital's PC-Alpha 164SX boards.
 * Writing the driver was quite simple, since most of the job is
 * done by the generic pci-ide support.
 * The hard part was finding the CY82C693's datasheet on Cypress's
 * web page :-(. But Altavista solved this problem :-).
 *
 *
 * Notes:
 * - I recently got a 16.8G IBM DTTA, so I was able to test it with
 *   a large and fast disk - the results look great, so I'd say the
 *   driver is working fine :-)
 *   hdparm -t reports 8.17 MB/sec at about 6% CPU usage for the DTTA
 * - this is my first linux driver, so there's probably a lot  of room
 *   for optimizations and bug fixing, so feel free to do it.
 * - if using PIO mode it's a good idea to set the PIO mode and
 *   32-bit I/O support (if possible), e.g. hdparm -p2 -c1 /dev/hda
 * - I had some problems with my IBM DHEA with PIO modes < 2
 *   (lost interrupts) ?????
 * - first tests with DMA look okay, they seem to work, but there is a
 *   problem with sound - the BusMaster IDE TimeOut should fixed this
 *
 * Ancient History:
 * AMH@1999-08-24: v0.34 init_cy82c693_chip moved to pci_init_cy82c693
 * ASK@1999-01-23: v0.33 made a few minor code clean ups
 *                       removed DMA clock speed setting by default
 *                       added boot message
 * ASK@1998-11-01: v0.32 added support to set BusMaster IDE TimeOut
 *                       added support to set DMA Controller Clock Speed
 * ASK@1998-10-31: v0.31 fixed problem with setting to high DMA modes
 *                       on some drives.
 * ASK@1998-10-29: v0.3 added support to set DMA modes
 * ASK@1998-10-28: v0.2 added support to set PIO modes
 * ASK@1998-10-27: v0.1 first version - chipset detection
 *
 */

#include <linux/module.h>
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <linux/init.h>

#include <asm/io.h>

/* the current version */
#define CY82_VERSION    "CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs@altavista.net)"

/*
 *      The following are used to debug the driver.
 */
#define CY82C693_DEBUG_LOGS     0
#define CY82C693_DEBUG_INFO     0

/* define CY82C693_SETDMA_CLOCK to set DMA Controller Clock Speed to ATCLK */
#undef CY82C693_SETDMA_CLOCK

/*
 *      NOTE: the value for busmaster timeout is tricky and I got it by
 *      trial and error!  By using a to low value will cause DMA timeouts
 *      and drop IDE performance, and by using a to high value will cause
 *      audio playback to scatter.
 *      If you know a better value or how to calc it, please let me know.
 */

/* twice the value written in cy82c693ub datasheet */
#define BUSMASTER_TIMEOUT       0x50
/*
 * the value above was tested on my machine and it seems to work okay
 */

/* here are the offset definitions for the registers */
#define CY82_IDE_CMDREG         0x04
#define CY82_IDE_ADDRSETUP      0x48
#define CY82_IDE_MASTER_IOR     0x4C
#define CY82_IDE_MASTER_IOW     0x4D
#define CY82_IDE_SLAVE_IOR      0x4E
#define CY82_IDE_SLAVE_IOW      0x4F
#define CY82_IDE_MASTER_8BIT    0x50
#define CY82_IDE_SLAVE_8BIT     0x51

#define CY82_INDEX_PORT         0x22
#define CY82_DATA_PORT          0x23

#define CY82_INDEX_CTRLREG1     0x01
#define CY82_INDEX_CHANNEL0     0x30
#define CY82_INDEX_CHANNEL1     0x31
#define CY82_INDEX_TIMEOUT      0x32

/* the min and max PCI bus speed in MHz - from datasheet */
#define CY82C963_MIN_BUS_SPEED  25
#define CY82C963_MAX_BUS_SPEED  33

/* the struct for the PIO mode timings */
typedef struct pio_clocks_s {
        u8      address_time;   /* Address setup (clocks) */
        u8      time_16r;       /* clocks for 16bit IOR (0xF0=Active/data, 0x0F=Recovery) */
        u8      time_16w;       /* clocks for 16bit IOW (0xF0=Active/data, 0x0F=Recovery) */
        u8      time_8;         /* clocks for 8bit (0xF0=Active/data, 0x0F=Recovery) */
} pio_clocks_t;

/*
 * calc clocks using bus_speed
 * returns (rounded up) time in bus clocks for time in ns
 */
static int calc_clk(int time, int bus_speed)
{
        int clocks;

        clocks = (time*bus_speed+999)/1000 - 1;

        if (clocks < 0)
                clocks = 0;

        if (clocks > 0x0F)
                clocks = 0x0F;

        return clocks;
}

/*
 * compute the values for the clock registers for PIO
 * mode and pci_clk [MHz] speed
 *
 * NOTE: for mode 0,1 and 2 drives 8-bit IDE command control registers are used
 *       for mode 3 and 4 drives 8 and 16-bit timings are the same
 *
 */
static void compute_clocks(u8 pio, pio_clocks_t *p_pclk)
{
        int clk1, clk2;
        int bus_speed = ide_pci_clk ? ide_pci_clk : system_bus_clock();

        /* we don't check against CY82C693's min and max speed,
         * so you can play with the idebus=xx parameter
         */

        /* let's calc the address setup time clocks */
        p_pclk->address_time = (u8)calc_clk(ide_pio_timings[pio].setup_time, bus_speed);

        /* let's calc the active and recovery time clocks */
        clk1 = calc_clk(ide_pio_timings[pio].active_time, bus_speed);

        /* calc recovery timing */
        clk2 =  ide_pio_timings[pio].cycle_time -
                ide_pio_timings[pio].active_time -
                ide_pio_timings[pio].setup_time;

        clk2 = calc_clk(clk2, bus_speed);

        clk1 = (clk1<<4)|clk2;  /* combine active and recovery clocks */

        /* note: we use the same values for 16bit IOR and IOW
         *      those are all the same, since I don't have other
         *      timings than those from ide-lib.c
         */

        p_pclk->time_16r = (u8)clk1;
        p_pclk->time_16w = (u8)clk1;

        /* what are good values for 8bit ?? */
        p_pclk->time_8 = (u8)clk1;
}

/*
 * set DMA mode a specific channel for CY82C693
 */

static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
        ide_hwif_t *hwif = drive->hwif;
        u8 single = (mode & 0x10) >> 4, index = 0, data = 0;

        index = hwif->channel ? CY82_INDEX_CHANNEL1 : CY82_INDEX_CHANNEL0;

#if CY82C693_DEBUG_LOGS
        /* for debug let's show the previous values */

        outb(index, CY82_INDEX_PORT);
        data = inb(CY82_DATA_PORT);

        printk(KERN_INFO "%s (ch=%d, dev=%d): DMA mode is %d (single=%d)\n",
                drive->name, HWIF(drive)->channel, drive->select.b.unit,
                (data&0x3), ((data>>2)&1));
#endif /* CY82C693_DEBUG_LOGS */

        data = (mode & 3) | (single << 2);

        outb(index, CY82_INDEX_PORT);
        outb(data, CY82_DATA_PORT);

#if CY82C693_DEBUG_INFO
        printk(KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n",
                drive->name, HWIF(drive)->channel, drive->select.b.unit,
                mode & 3, single);
#endif /* CY82C693_DEBUG_INFO */

        /*
         * note: below we set the value for Bus Master IDE TimeOut Register
         * I'm not absolutly sure what this does, but it solved my problem
         * with IDE DMA and sound, so I now can play sound and work with
         * my IDE driver at the same time :-)
         *
         * If you know the correct (best) value for this register please
         * let me know - ASK
         */

        data = BUSMASTER_TIMEOUT;
        outb(CY82_INDEX_TIMEOUT, CY82_INDEX_PORT);
        outb(data, CY82_DATA_PORT);

#if CY82C693_DEBUG_INFO
        printk(KERN_INFO "%s: Set IDE Bus Master TimeOut Register to 0x%X\n",
                drive->name, data);
#endif /* CY82C693_DEBUG_INFO */
}

static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
        ide_hwif_t *hwif = HWIF(drive);
        struct pci_dev *dev = to_pci_dev(hwif->dev);
        pio_clocks_t pclk;
        unsigned int addrCtrl;

        /* select primary or secondary channel */
        if (hwif->index > 0) {  /* drive is on the secondary channel */
                dev = pci_get_slot(dev->bus, dev->devfn+1);
                if (!dev) {
                        printk(KERN_ERR "%s: tune_drive: "
                                "Cannot find secondary interface!\n",
                                drive->name);
                        return;
                }
        }

#if CY82C693_DEBUG_LOGS
        /* for debug let's show the register values */

        if (drive->select.b.unit == 0) {
                /*
                 * get master drive registers
                 * address setup control register
                 * is 32 bit !!!
                 */
                pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
                addrCtrl &= 0x0F;

                /* now let's get the remaining registers */
                pci_read_config_byte(dev, CY82_IDE_MASTER_IOR, &pclk.time_16r);
                pci_read_config_byte(dev, CY82_IDE_MASTER_IOW, &pclk.time_16w);
                pci_read_config_byte(dev, CY82_IDE_MASTER_8BIT, &pclk.time_8);
        } else {
                /*
                 * set slave drive registers
                 * address setup control register
                 * is 32 bit !!!
                 */
                pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);

                addrCtrl &= 0xF0;
                addrCtrl >>= 4;

                /* now let's get the remaining registers */
                pci_read_config_byte(dev, CY82_IDE_SLAVE_IOR, &pclk.time_16r);
                pci_read_config_byte(dev, CY82_IDE_SLAVE_IOW, &pclk.time_16w);
                pci_read_config_byte(dev, CY82_IDE_SLAVE_8BIT, &pclk.time_8);
        }

        printk(KERN_INFO "%s (ch=%d, dev=%d): PIO timing is "
                "(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
                drive->name, hwif->channel, drive->select.b.unit,
                addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
#endif /* CY82C693_DEBUG_LOGS */

        /* let's calc the values for this PIO mode */
        compute_clocks(pio, &pclk);

        /* now let's write  the clocks registers */
        if (drive->select.b.unit == 0) {
                /*
                 * set master drive
                 * address setup control register
                 * is 32 bit !!!
                 */
                pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);

                addrCtrl &= (~0xF);
                addrCtrl |= (unsigned int)pclk.address_time;
                pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);

                /* now let's set the remaining registers */
                pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r);
                pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w);
                pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8);

                addrCtrl &= 0xF;
        } else {
                /*
                 * set slave drive
                 * address setup control register
                 * is 32 bit !!!
                 */
                pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);

                addrCtrl &= (~0xF0);
                addrCtrl |= ((unsigned int)pclk.address_time<<4);
                pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);

                /* now let's set the remaining registers */
                pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r);
                pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w);
                pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8);

                addrCtrl >>= 4;
                addrCtrl &= 0xF;
        }

#if CY82C693_DEBUG_INFO
        printk(KERN_INFO "%s (ch=%d, dev=%d): set PIO timing to "
                "(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
                drive->name, hwif->channel, drive->select.b.unit,
                addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
#endif /* CY82C693_DEBUG_INFO */
}

/*
 * this function is called during init and is used to setup the cy82c693 chip
 */
static unsigned int __devinit init_chipset_cy82c693(struct pci_dev *dev, const char *name)
{
        if (PCI_FUNC(dev->devfn) != 1)
                return 0;

#ifdef CY82C693_SETDMA_CLOCK
        u8 data = 0;
#endif /* CY82C693_SETDMA_CLOCK */

        /* write info about this verion of the driver */
        printk(KERN_INFO CY82_VERSION "\n");

#ifdef CY82C693_SETDMA_CLOCK
       /* okay let's set the DMA clock speed */

        outb(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT);
        data = inb(CY82_DATA_PORT);

#if CY82C693_DEBUG_INFO
        printk(KERN_INFO "%s: Peripheral Configuration Register: 0x%X\n",
                name, data);
#endif /* CY82C693_DEBUG_INFO */

        /*
         * for some reason sometimes the DMA controller
         * speed is set to ATCLK/2 ???? - we fix this here
         *
         * note: i don't know what causes this strange behaviour,
         *       but even changing the dma speed doesn't solve it :-(
         *       the ide performance is still only half the normal speed
         *
         *       if anybody knows what goes wrong with my machine, please
         *       let me know - ASK
         */

        data |= 0x03;

        outb(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT);
        outb(data, CY82_DATA_PORT);

#if CY82C693_DEBUG_INFO
        printk(KERN_INFO "%s: New Peripheral Configuration Register: 0x%X\n",
                name, data);
#endif /* CY82C693_DEBUG_INFO */

#endif /* CY82C693_SETDMA_CLOCK */
        return 0;
}

static void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
{
        static ide_hwif_t *primary;
        struct pci_dev *dev = to_pci_dev(hwif->dev);

        if (PCI_FUNC(dev->devfn) == 1)
                primary = hwif;
        else {
                hwif->mate = primary;
                hwif->channel = 1;
        }
}

static const struct ide_port_ops cy82c693_port_ops = {
        .set_pio_mode           = cy82c693_set_pio_mode,
        .set_dma_mode           = cy82c693_set_dma_mode,
};

static const struct ide_port_info cy82c693_chipset __devinitdata = {
        .name           = "CY82C693",
        .init_chipset   = init_chipset_cy82c693,
        .init_iops      = init_iops_cy82c693,
        .port_ops       = &cy82c693_port_ops,
        .chipset        = ide_cy82c693,
        .host_flags     = IDE_HFLAG_SINGLE,
        .pio_mask       = ATA_PIO4,
        .swdma_mask     = ATA_SWDMA2,
        .mwdma_mask     = ATA_MWDMA2,
};

static int __devinit cy82c693_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
        struct pci_dev *dev2;
        int ret = -ENODEV;

        /* CY82C693 is more than only a IDE controller.
           Function 1 is primary IDE channel, function 2 - secondary. */
        if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE &&
            PCI_FUNC(dev->devfn) == 1) {
                dev2 = pci_get_slot(dev->bus, dev->devfn + 1);
                ret = ide_setup_pci_devices(dev, dev2, &cy82c693_chipset);
                /* We leak pci refs here but thats ok - we can't be unloaded */
        }
        return ret;
}

static const struct pci_device_id cy82c693_pci_tbl[] = {
        { PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), 0 },
        { 0, },
};
MODULE_DEVICE_TABLE(pci, cy82c693_pci_tbl);

static struct pci_driver driver = {
        .name           = "Cypress_IDE",
        .id_table       = cy82c693_pci_tbl,
        .probe          = cy82c693_init_one,
};

static int __init cy82c693_ide_init(void)
{
        return ide_pci_register_driver(&driver);
}

module_init(cy82c693_ide_init);

MODULE_AUTHOR("Andreas Krebs, Andre Hedrick");
MODULE_DESCRIPTION("PCI driver module for the Cypress CY82C693 IDE");
MODULE_LICENSE("GPL");