hw/tusb6010.c

   1 /*
   2  * Texas Instruments TUSB6010 emulation.
   3  * Based on reverse-engineering of a linux driver.
   4  *
   5  * Copyright (C) 2008 Nokia Corporation
   6  * Written by Andrzej Zaborowski <andrew@openedhand.com>
   7  *
   8  * This program is free software; you can redistribute it and/or
   9  * modify it under the terms of the GNU General Public License as
  10  * published by the Free Software Foundation; either version 2 or
  11  * (at your option) version 3 of the License.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License along
  19  * with this program; if not, write to the Free Software Foundation, Inc.,
  20  * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
  21  */
  22 #include "qemu-common.h"
  23 #include "qemu-timer.h"
  24 #include "usb.h"
  25 #include "omap.h"
  26 #include "irq.h"
  27 #include "devices.h"
  28
  29 struct TUSBState {
  30     int iomemtype[2];
  31     qemu_irq irq;
  32     MUSBState *musb;
  33     QEMUTimer *otg_timer;
  34     QEMUTimer *pwr_timer;
  35
  36     int power;
  37     uint32_t scratch;
  38     uint16_t test_reset;
  39     uint32_t prcm_config;
  40     uint32_t prcm_mngmt;
  41     uint16_t otg_status;
  42     uint32_t dev_config;
  43     int host_mode;
  44     uint32_t intr;
  45     uint32_t intr_ok;
  46     uint32_t mask;
  47     uint32_t usbip_intr;
  48     uint32_t usbip_mask;
  49     uint32_t gpio_intr;
  50     uint32_t gpio_mask;
  51     uint32_t gpio_config;
  52     uint32_t dma_intr;
  53     uint32_t dma_mask;
  54     uint32_t dma_map;
  55     uint32_t dma_config;
  56     uint32_t ep0_config;
  57     uint32_t rx_config[15];
  58     uint32_t tx_config[15];
  59     uint32_t wkup_mask;
  60     uint32_t pullup[2];
  61     uint32_t control_config;
  62     uint32_t otg_timer_val;
  63 };
  64
  65 #define TUSB_DEVCLOCK                   60000000        /* 60 MHz */
  66
  67 #define TUSB_VLYNQ_CTRL                 0x004
  68
  69 /* Mentor Graphics OTG core registers.  */
  70 #define TUSB_BASE_OFFSET                0x400
  71
  72 /* FIFO registers, 32-bit.  */
  73 #define TUSB_FIFO_BASE                  0x600
  74
  75 /* Device System & Control registers, 32-bit.  */
  76 #define TUSB_SYS_REG_BASE               0x800
  77
  78 #define TUSB_DEV_CONF                   (TUSB_SYS_REG_BASE + 0x000)
  79 #define TUSB_DEV_CONF_USB_HOST_MODE     (1 << 16)
  80 #define TUSB_DEV_CONF_PROD_TEST_MODE    (1 << 15)
  81 #define TUSB_DEV_CONF_SOFT_ID           (1 << 1)
  82 #define TUSB_DEV_CONF_ID_SEL            (1 << 0)
  83
  84 #define TUSB_PHY_OTG_CTRL_ENABLE        (TUSB_SYS_REG_BASE + 0x004)
  85 #define TUSB_PHY_OTG_CTRL               (TUSB_SYS_REG_BASE + 0x008)
  86 #define TUSB_PHY_OTG_CTRL_WRPROTECT     (0xa5 << 24)
  87 #define TUSB_PHY_OTG_CTRL_O_ID_PULLUP   (1 << 23)
  88 #define TUSB_PHY_OTG_CTRL_O_VBUS_DET_EN (1 << 19)
  89 #define TUSB_PHY_OTG_CTRL_O_SESS_END_EN (1 << 18)
  90 #define TUSB_PHY_OTG_CTRL_TESTM2        (1 << 17)
  91 #define TUSB_PHY_OTG_CTRL_TESTM1        (1 << 16)
  92 #define TUSB_PHY_OTG_CTRL_TESTM0        (1 << 15)
  93 #define TUSB_PHY_OTG_CTRL_TX_DATA2      (1 << 14)
  94 #define TUSB_PHY_OTG_CTRL_TX_GZ2        (1 << 13)
  95 #define TUSB_PHY_OTG_CTRL_TX_ENABLE2    (1 << 12)
  96 #define TUSB_PHY_OTG_CTRL_DM_PULLDOWN   (1 << 11)
  97 #define TUSB_PHY_OTG_CTRL_DP_PULLDOWN   (1 << 10)
  98 #define TUSB_PHY_OTG_CTRL_OSC_EN        (1 << 9)
  99 #define TUSB_PHY_OTG_CTRL_PHYREF_CLK(v) (((v) & 3) << 7)
 100 #define TUSB_PHY_OTG_CTRL_PD            (1 << 6)
 101 #define TUSB_PHY_OTG_CTRL_PLL_ON        (1 << 5)
 102 #define TUSB_PHY_OTG_CTRL_EXT_RPU       (1 << 4)
 103 #define TUSB_PHY_OTG_CTRL_PWR_GOOD      (1 << 3)
 104 #define TUSB_PHY_OTG_CTRL_RESET         (1 << 2)
 105 #define TUSB_PHY_OTG_CTRL_SUSPENDM      (1 << 1)
 106 #define TUSB_PHY_OTG_CTRL_CLK_MODE      (1 << 0)
 107
 108 /* OTG status register */
 109 #define TUSB_DEV_OTG_STAT               (TUSB_SYS_REG_BASE + 0x00c)
 110 #define TUSB_DEV_OTG_STAT_PWR_CLK_GOOD  (1 << 8)
 111 #define TUSB_DEV_OTG_STAT_SESS_END      (1 << 7)
 112 #define TUSB_DEV_OTG_STAT_SESS_VALID    (1 << 6)
 113 #define TUSB_DEV_OTG_STAT_VBUS_VALID    (1 << 5)
 114 #define TUSB_DEV_OTG_STAT_VBUS_SENSE    (1 << 4)
 115 #define TUSB_DEV_OTG_STAT_ID_STATUS     (1 << 3)
 116 #define TUSB_DEV_OTG_STAT_HOST_DISCON   (1 << 2)
 117 #define TUSB_DEV_OTG_STAT_LINE_STATE    (3 << 0)
 118 #define TUSB_DEV_OTG_STAT_DP_ENABLE     (1 << 1)
 119 #define TUSB_DEV_OTG_STAT_DM_ENABLE     (1 << 0)
 120
 121 #define TUSB_DEV_OTG_TIMER              (TUSB_SYS_REG_BASE + 0x010)
 122 #define TUSB_DEV_OTG_TIMER_ENABLE       (1 << 31)
 123 #define TUSB_DEV_OTG_TIMER_VAL(v)       ((v) & 0x07ffffff)
 124 #define TUSB_PRCM_REV                   (TUSB_SYS_REG_BASE + 0x014)
 125
 126 /* PRCM configuration register */
 127 #define TUSB_PRCM_CONF                  (TUSB_SYS_REG_BASE + 0x018)
 128 #define TUSB_PRCM_CONF_SFW_CPEN         (1 << 24)
 129 #define TUSB_PRCM_CONF_SYS_CLKSEL(v)    (((v) & 3) << 16)
 130
 131 /* PRCM management register */
 132 #define TUSB_PRCM_MNGMT                 (TUSB_SYS_REG_BASE + 0x01c)
 133 #define TUSB_PRCM_MNGMT_SRP_FIX_TMR(v)  (((v) & 0xf) << 25)
 134 #define TUSB_PRCM_MNGMT_SRP_FIX_EN      (1 << 24)
 135 #define TUSB_PRCM_MNGMT_VBUS_VAL_TMR(v) (((v) & 0xf) << 20)
 136 #define TUSB_PRCM_MNGMT_VBUS_VAL_FLT_EN (1 << 19)
 137 #define TUSB_PRCM_MNGMT_DFT_CLK_DIS     (1 << 18)
 138 #define TUSB_PRCM_MNGMT_VLYNQ_CLK_DIS   (1 << 17)
 139 #define TUSB_PRCM_MNGMT_OTG_SESS_END_EN (1 << 10)
 140 #define TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN (1 << 9)
 141 #define TUSB_PRCM_MNGMT_OTG_ID_PULLUP   (1 << 8)
 142 #define TUSB_PRCM_MNGMT_15_SW_EN        (1 << 4)
 143 #define TUSB_PRCM_MNGMT_33_SW_EN        (1 << 3)
 144 #define TUSB_PRCM_MNGMT_5V_CPEN         (1 << 2)
 145 #define TUSB_PRCM_MNGMT_PM_IDLE         (1 << 1)
 146 #define TUSB_PRCM_MNGMT_DEV_IDLE        (1 << 0)
 147
 148 /* Wake-up source clear and mask registers */
 149 #define TUSB_PRCM_WAKEUP_SOURCE         (TUSB_SYS_REG_BASE + 0x020)
 150 #define TUSB_PRCM_WAKEUP_CLEAR          (TUSB_SYS_REG_BASE + 0x028)
 151 #define TUSB_PRCM_WAKEUP_MASK           (TUSB_SYS_REG_BASE + 0x02c)
 152 #define TUSB_PRCM_WAKEUP_RESERVED_BITS  (0xffffe << 13)
 153 #define TUSB_PRCM_WGPIO_7               (1 << 12)
 154 #define TUSB_PRCM_WGPIO_6               (1 << 11)
 155 #define TUSB_PRCM_WGPIO_5               (1 << 10)
 156 #define TUSB_PRCM_WGPIO_4               (1 << 9)
 157 #define TUSB_PRCM_WGPIO_3               (1 << 8)
 158 #define TUSB_PRCM_WGPIO_2               (1 << 7)
 159 #define TUSB_PRCM_WGPIO_1               (1 << 6)
 160 #define TUSB_PRCM_WGPIO_0               (1 << 5)
 161 #define TUSB_PRCM_WHOSTDISCON           (1 << 4)        /* Host disconnect */
 162 #define TUSB_PRCM_WBUS                  (1 << 3)        /* USB bus resume */
 163 #define TUSB_PRCM_WNORCS                (1 << 2)        /* NOR chip select */
 164 #define TUSB_PRCM_WVBUS                 (1 << 1)        /* OTG PHY VBUS */
 165 #define TUSB_PRCM_WID                   (1 << 0)        /* OTG PHY ID detect */
 166
 167 #define TUSB_PULLUP_1_CTRL              (TUSB_SYS_REG_BASE + 0x030)
 168 #define TUSB_PULLUP_2_CTRL              (TUSB_SYS_REG_BASE + 0x034)
 169 #define TUSB_INT_CTRL_REV               (TUSB_SYS_REG_BASE + 0x038)
 170 #define TUSB_INT_CTRL_CONF              (TUSB_SYS_REG_BASE + 0x03c)
 171 #define TUSB_USBIP_INT_SRC              (TUSB_SYS_REG_BASE + 0x040)
 172 #define TUSB_USBIP_INT_SET              (TUSB_SYS_REG_BASE + 0x044)
 173 #define TUSB_USBIP_INT_CLEAR            (TUSB_SYS_REG_BASE + 0x048)
 174 #define TUSB_USBIP_INT_MASK             (TUSB_SYS_REG_BASE + 0x04c)
 175 #define TUSB_DMA_INT_SRC                (TUSB_SYS_REG_BASE + 0x050)
 176 #define TUSB_DMA_INT_SET                (TUSB_SYS_REG_BASE + 0x054)
 177 #define TUSB_DMA_INT_CLEAR              (TUSB_SYS_REG_BASE + 0x058)
 178 #define TUSB_DMA_INT_MASK               (TUSB_SYS_REG_BASE + 0x05c)
 179 #define TUSB_GPIO_INT_SRC               (TUSB_SYS_REG_BASE + 0x060)
 180 #define TUSB_GPIO_INT_SET               (TUSB_SYS_REG_BASE + 0x064)
 181 #define TUSB_GPIO_INT_CLEAR             (TUSB_SYS_REG_BASE + 0x068)
 182 #define TUSB_GPIO_INT_MASK              (TUSB_SYS_REG_BASE + 0x06c)
 183
 184 /* NOR flash interrupt source registers */
 185 #define TUSB_INT_SRC                    (TUSB_SYS_REG_BASE + 0x070)
 186 #define TUSB_INT_SRC_SET                (TUSB_SYS_REG_BASE + 0x074)
 187 #define TUSB_INT_SRC_CLEAR              (TUSB_SYS_REG_BASE + 0x078)
 188 #define TUSB_INT_MASK                   (TUSB_SYS_REG_BASE + 0x07c)
 189 #define TUSB_INT_SRC_TXRX_DMA_DONE      (1 << 24)
 190 #define TUSB_INT_SRC_USB_IP_CORE        (1 << 17)
 191 #define TUSB_INT_SRC_OTG_TIMEOUT        (1 << 16)
 192 #define TUSB_INT_SRC_VBUS_SENSE_CHNG    (1 << 15)
 193 #define TUSB_INT_SRC_ID_STATUS_CHNG     (1 << 14)
 194 #define TUSB_INT_SRC_DEV_WAKEUP         (1 << 13)
 195 #define TUSB_INT_SRC_DEV_READY          (1 << 12)
 196 #define TUSB_INT_SRC_USB_IP_TX          (1 << 9)
 197 #define TUSB_INT_SRC_USB_IP_RX          (1 << 8)
 198 #define TUSB_INT_SRC_USB_IP_VBUS_ERR    (1 << 7)
 199 #define TUSB_INT_SRC_USB_IP_VBUS_REQ    (1 << 6)
 200 #define TUSB_INT_SRC_USB_IP_DISCON      (1 << 5)
 201 #define TUSB_INT_SRC_USB_IP_CONN        (1 << 4)
 202 #define TUSB_INT_SRC_USB_IP_SOF         (1 << 3)
 203 #define TUSB_INT_SRC_USB_IP_RST_BABBLE  (1 << 2)
 204 #define TUSB_INT_SRC_USB_IP_RESUME      (1 << 1)
 205 #define TUSB_INT_SRC_USB_IP_SUSPEND     (1 << 0)
 206
 207 #define TUSB_GPIO_REV                   (TUSB_SYS_REG_BASE + 0x080)
 208 #define TUSB_GPIO_CONF                  (TUSB_SYS_REG_BASE + 0x084)
 209 #define TUSB_DMA_CTRL_REV               (TUSB_SYS_REG_BASE + 0x100)
 210 #define TUSB_DMA_REQ_CONF               (TUSB_SYS_REG_BASE + 0x104)
 211 #define TUSB_EP0_CONF                   (TUSB_SYS_REG_BASE + 0x108)
 212 #define TUSB_EP_IN_SIZE                 (TUSB_SYS_REG_BASE + 0x10c)
 213 #define TUSB_DMA_EP_MAP                 (TUSB_SYS_REG_BASE + 0x148)
 214 #define TUSB_EP_OUT_SIZE                (TUSB_SYS_REG_BASE + 0x14c)
 215 #define TUSB_EP_MAX_PACKET_SIZE_OFFSET  (TUSB_SYS_REG_BASE + 0x188)
 216 #define TUSB_SCRATCH_PAD                (TUSB_SYS_REG_BASE + 0x1c4)
 217 #define TUSB_WAIT_COUNT                 (TUSB_SYS_REG_BASE + 0x1c8)
 218 #define TUSB_PROD_TEST_RESET            (TUSB_SYS_REG_BASE + 0x1d8)
 219
 220 #define TUSB_DIDR1_LO                   (TUSB_SYS_REG_BASE + 0x1f8)
 221 #define TUSB_DIDR1_HI                   (TUSB_SYS_REG_BASE + 0x1fc)
 222
 223 /* Device System & Control register bitfields */
 224 #define TUSB_INT_CTRL_CONF_INT_RLCYC(v) (((v) & 0x7) << 18)
 225 #define TUSB_INT_CTRL_CONF_INT_POLARITY (1 << 17)
 226 #define TUSB_INT_CTRL_CONF_INT_MODE     (1 << 16)
 227 #define TUSB_GPIO_CONF_DMAREQ(v)        (((v) & 0x3f) << 24)
 228 #define TUSB_DMA_REQ_CONF_BURST_SIZE(v) (((v) & 3) << 26)
 229 #define TUSB_DMA_REQ_CONF_DMA_RQ_EN(v)  (((v) & 0x3f) << 20)
 230 #define TUSB_DMA_REQ_CONF_DMA_RQ_ASR(v) (((v) & 0xf) << 16)
 231 #define TUSB_EP0_CONFIG_SW_EN           (1 << 8)
 232 #define TUSB_EP0_CONFIG_DIR_TX          (1 << 7)
 233 #define TUSB_EP0_CONFIG_XFR_SIZE(v)     ((v) & 0x7f)
 234 #define TUSB_EP_CONFIG_SW_EN            (1 << 31)
 235 #define TUSB_EP_CONFIG_XFR_SIZE(v)      ((v) & 0x7fffffff)
 236 #define TUSB_PROD_TEST_RESET_VAL        0xa596
 237
 238 int tusb6010_sync_io(TUSBState *s)
 239 {
 240     return s->iomemtype[0];
 241 }
 242
 243 int tusb6010_async_io(TUSBState *s)
 244 {
 245     return s->iomemtype[1];
 246 }
 247
 248 static void tusb_intr_update(TUSBState *s)
 249 {
 250     if (s->control_config & TUSB_INT_CTRL_CONF_INT_POLARITY)
 251         qemu_set_irq(s->irq, s->intr & ~s->mask & s->intr_ok);
 252     else
 253         qemu_set_irq(s->irq, (!(s->intr & ~s->mask)) & s->intr_ok);
 254 }
 255
 256 static void tusb_usbip_intr_update(TUSBState *s)
 257 {
 258     /* TX interrupt in the MUSB */
 259     if (s->usbip_intr & 0x0000ffff & ~s->usbip_mask)
 260         s->intr |= TUSB_INT_SRC_USB_IP_TX;
 261     else
 262         s->intr &= ~TUSB_INT_SRC_USB_IP_TX;
 263
 264     /* RX interrupt in the MUSB */
 265     if (s->usbip_intr & 0xffff0000 & ~s->usbip_mask)
 266         s->intr |= TUSB_INT_SRC_USB_IP_RX;
 267     else
 268         s->intr &= ~TUSB_INT_SRC_USB_IP_RX;
 269
 270     /* XXX: What about TUSB_INT_SRC_USB_IP_CORE?  */
 271
 272     tusb_intr_update(s);
 273 }
 274
 275 static void tusb_dma_intr_update(TUSBState *s)
 276 {
 277     if (s->dma_intr & ~s->dma_mask)
 278         s->intr |= TUSB_INT_SRC_TXRX_DMA_DONE;
 279     else
 280         s->intr &= ~TUSB_INT_SRC_TXRX_DMA_DONE;
 281
 282     tusb_intr_update(s);
 283 }
 284
 285 static void tusb_gpio_intr_update(TUSBState *s)
 286 {
 287     /* TODO: How is this signalled?  */
 288 }
 289
 290 extern CPUReadMemoryFunc *musb_read[];
 291 extern CPUWriteMemoryFunc *musb_write[];
 292
 293 static uint32_t tusb_async_readb(void *opaque, target_phys_addr_t addr)
 294 {
 295     TUSBState *s = (TUSBState *) opaque;
 296
 297     switch (addr & 0xfff) {
 298     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 299         return musb_read[0](s->musb, addr & 0x1ff);
 300
 301     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 302         return musb_read[0](s->musb, 0x20 + ((addr >> 3) & 0x3c));
 303     }
 304
 305     printf("%s: unknown register at %03x\n",
 306                     __FUNCTION__, (int) (addr & 0xfff));
 307     return 0;
 308 }
 309
 310 static uint32_t tusb_async_readh(void *opaque, target_phys_addr_t addr)
 311 {
 312     TUSBState *s = (TUSBState *) opaque;
 313
 314     switch (addr & 0xfff) {
 315     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 316         return musb_read[1](s->musb, addr & 0x1ff);
 317
 318     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 319         return musb_read[1](s->musb, 0x20 + ((addr >> 3) & 0x3c));
 320     }
 321
 322     printf("%s: unknown register at %03x\n",
 323                     __FUNCTION__, (int) (addr & 0xfff));
 324     return 0;
 325 }
 326
 327 static uint32_t tusb_async_readw(void *opaque, target_phys_addr_t addr)
 328 {
 329     TUSBState *s = (TUSBState *) opaque;
 330     int offset = addr & 0xfff;
 331     int epnum;
 332     uint32_t ret;
 333
 334     switch (offset) {
 335     case TUSB_DEV_CONF:
 336         return s->dev_config;
 337
 338     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 339         return musb_read[2](s->musb, offset & 0x1ff);
 340
 341     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 342         return musb_read[2](s->musb, 0x20 + ((addr >> 3) & 0x3c));
 343
 344     case TUSB_PHY_OTG_CTRL_ENABLE:
 345     case TUSB_PHY_OTG_CTRL:
 346         return 0x00;    /* TODO */
 347
 348     case TUSB_DEV_OTG_STAT:
 349         ret = s->otg_status;
 350 #if 0
 351         if (!(s->prcm_mngmt & TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN))
 352             ret &= ~TUSB_DEV_OTG_STAT_VBUS_VALID;
 353 #endif
 354         return ret;
 355     case TUSB_DEV_OTG_TIMER:
 356         return s->otg_timer_val;
 357
 358     case TUSB_PRCM_REV:
 359         return 0x20;
 360     case TUSB_PRCM_CONF:
 361         return s->prcm_config;
 362     case TUSB_PRCM_MNGMT:
 363         return s->prcm_mngmt;
 364     case TUSB_PRCM_WAKEUP_SOURCE:
 365     case TUSB_PRCM_WAKEUP_CLEAR:        /* TODO: What does this one return?  */
 366         return 0x00000000;
 367     case TUSB_PRCM_WAKEUP_MASK:
 368         return s->wkup_mask;
 369
 370     case TUSB_PULLUP_1_CTRL:
 371         return s->pullup[0];
 372     case TUSB_PULLUP_2_CTRL:
 373         return s->pullup[1];
 374
 375     case TUSB_INT_CTRL_REV:
 376         return 0x20;
 377     case TUSB_INT_CTRL_CONF:
 378         return s->control_config;
 379
 380     case TUSB_USBIP_INT_SRC:
 381     case TUSB_USBIP_INT_SET:    /* TODO: What do these two return?  */
 382     case TUSB_USBIP_INT_CLEAR:
 383         return s->usbip_intr;
 384     case TUSB_USBIP_INT_MASK:
 385         return s->usbip_mask;
 386
 387     case TUSB_DMA_INT_SRC:
 388     case TUSB_DMA_INT_SET:      /* TODO: What do these two return?  */
 389     case TUSB_DMA_INT_CLEAR:
 390         return s->dma_intr;
 391     case TUSB_DMA_INT_MASK:
 392         return s->dma_mask;
 393
 394     case TUSB_GPIO_INT_SRC:     /* TODO: What do these two return?  */
 395     case TUSB_GPIO_INT_SET:
 396     case TUSB_GPIO_INT_CLEAR:
 397         return s->gpio_intr;
 398     case TUSB_GPIO_INT_MASK:
 399         return s->gpio_mask;
 400
 401     case TUSB_INT_SRC:
 402     case TUSB_INT_SRC_SET:      /* TODO: What do these two return?  */
 403     case TUSB_INT_SRC_CLEAR:
 404         return s->intr;
 405     case TUSB_INT_MASK:
 406         return s->mask;
 407
 408     case TUSB_GPIO_REV:
 409         return 0x30;
 410     case TUSB_GPIO_CONF:
 411         return s->gpio_config;
 412
 413     case TUSB_DMA_CTRL_REV:
 414         return 0x30;
 415     case TUSB_DMA_REQ_CONF:
 416         return s->dma_config;
 417     case TUSB_EP0_CONF:
 418         return s->ep0_config;
 419     case TUSB_EP_IN_SIZE ... (TUSB_EP_IN_SIZE + 0x3b):
 420         epnum = (offset - TUSB_EP_IN_SIZE) >> 2;
 421         return s->tx_config[epnum];
 422     case TUSB_DMA_EP_MAP:
 423         return s->dma_map;
 424     case TUSB_EP_OUT_SIZE ... (TUSB_EP_OUT_SIZE + 0x3b):
 425         epnum = (offset - TUSB_EP_OUT_SIZE) >> 2;
 426         return s->rx_config[epnum];
 427     case TUSB_EP_MAX_PACKET_SIZE_OFFSET ...
 428             (TUSB_EP_MAX_PACKET_SIZE_OFFSET + 0x3b):
 429         epnum = (offset - TUSB_EP_MAX_PACKET_SIZE_OFFSET) >> 2;
 430         return 0x00000000;      /* TODO */
 431     case TUSB_WAIT_COUNT:
 432         return 0x00;            /* TODO */
 433
 434     case TUSB_SCRATCH_PAD:
 435         return s->scratch;
 436
 437     case TUSB_PROD_TEST_RESET:
 438         return s->test_reset;
 439
 440     /* DIE IDs */
 441     case TUSB_DIDR1_LO:
 442         return 0xa9453c59;
 443     case TUSB_DIDR1_HI:
 444         return 0x54059adf;
 445     }
 446
 447     printf("%s: unknown register at %03x\n", __FUNCTION__, offset);
 448     return 0;
 449 }
 450
 451 static void tusb_async_writeb(void *opaque, target_phys_addr_t addr,
 452                 uint32_t value)
 453 {
 454     TUSBState *s = (TUSBState *) opaque;
 455
 456     switch (addr & 0xfff) {
 457     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 458         musb_write[0](s->musb, addr & 0x1ff, value);
 459         break;
 460
 461     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 462         musb_write[0](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
 463         break;
 464
 465     default:
 466         printf("%s: unknown register at %03x\n",
 467                         __FUNCTION__, (int) (addr & 0xfff));
 468         return;
 469     }
 470 }
 471
 472 static void tusb_async_writeh(void *opaque, target_phys_addr_t addr,
 473                 uint32_t value)
 474 {
 475     TUSBState *s = (TUSBState *) opaque;
 476
 477     switch (addr & 0xfff) {
 478     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 479         musb_write[1](s->musb, addr & 0x1ff, value);
 480         break;
 481
 482     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 483         musb_write[1](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
 484         break;
 485
 486     default:
 487         printf("%s: unknown register at %03x\n",
 488                         __FUNCTION__, (int) (addr & 0xfff));
 489         return;
 490     }
 491 }
 492
 493 static void tusb_async_writew(void *opaque, target_phys_addr_t addr,
 494                 uint32_t value)
 495 {
 496     TUSBState *s = (TUSBState *) opaque;
 497     int offset = addr & 0xfff;
 498     int epnum;
 499
 500     switch (offset) {
 501     case TUSB_VLYNQ_CTRL:
 502         break;
 503
 504     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 505         musb_write[2](s->musb, offset & 0x1ff, value);
 506         break;
 507
 508     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 509         musb_write[2](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
 510         break;
 511
 512     case TUSB_DEV_CONF:
 513         s->dev_config = value;
 514         s->host_mode = (value & TUSB_DEV_CONF_USB_HOST_MODE);
 515         if (value & TUSB_DEV_CONF_PROD_TEST_MODE)
 516             hw_error("%s: Product Test mode not allowed\n", __FUNCTION__);
 517         break;
 518
 519     case TUSB_PHY_OTG_CTRL_ENABLE:
 520     case TUSB_PHY_OTG_CTRL:
 521         return;         /* TODO */
 522     case TUSB_DEV_OTG_TIMER:
 523         s->otg_timer_val = value;
 524         if (value & TUSB_DEV_OTG_TIMER_ENABLE)
 525             qemu_mod_timer(s->otg_timer, qemu_get_clock(vm_clock) +
 526                             muldiv64(TUSB_DEV_OTG_TIMER_VAL(value),
 527                                     ticks_per_sec, TUSB_DEVCLOCK));
 528         else
 529             qemu_del_timer(s->otg_timer);
 530         break;
 531
 532     case TUSB_PRCM_CONF:
 533         s->prcm_config = value;
 534         break;
 535     case TUSB_PRCM_MNGMT:
 536         s->prcm_mngmt = value;
 537         break;
 538     case TUSB_PRCM_WAKEUP_CLEAR:
 539         break;
 540     case TUSB_PRCM_WAKEUP_MASK:
 541         s->wkup_mask = value;
 542         break;
 543
 544     case TUSB_PULLUP_1_CTRL:
 545         s->pullup[0] = value;
 546         break;
 547     case TUSB_PULLUP_2_CTRL:
 548         s->pullup[1] = value;
 549         break;
 550     case TUSB_INT_CTRL_CONF:
 551         s->control_config = value;
 552         tusb_intr_update(s);
 553         break;
 554
 555     case TUSB_USBIP_INT_SET:
 556         s->usbip_intr |= value;
 557         tusb_usbip_intr_update(s);
 558         break;
 559     case TUSB_USBIP_INT_CLEAR:
 560         s->usbip_intr &= ~value;
 561         tusb_usbip_intr_update(s);
 562         musb_core_intr_clear(s->musb, ~value);
 563         break;
 564     case TUSB_USBIP_INT_MASK:
 565         s->usbip_mask = value;
 566         tusb_usbip_intr_update(s);
 567         break;
 568
 569     case TUSB_DMA_INT_SET:
 570         s->dma_intr |= value;
 571         tusb_dma_intr_update(s);
 572         break;
 573     case TUSB_DMA_INT_CLEAR:
 574         s->dma_intr &= ~value;
 575         tusb_dma_intr_update(s);
 576         break;
 577     case TUSB_DMA_INT_MASK:
 578         s->dma_mask = value;
 579         tusb_dma_intr_update(s);
 580         break;
 581
 582     case TUSB_GPIO_INT_SET:
 583         s->gpio_intr |= value;
 584         tusb_gpio_intr_update(s);
 585         break;
 586     case TUSB_GPIO_INT_CLEAR:
 587         s->gpio_intr &= ~value;
 588         tusb_gpio_intr_update(s);
 589         break;
 590     case TUSB_GPIO_INT_MASK:
 591         s->gpio_mask = value;
 592         tusb_gpio_intr_update(s);
 593         break;
 594
 595     case TUSB_INT_SRC_SET:
 596         s->intr |= value;
 597         tusb_intr_update(s);
 598         break;
 599     case TUSB_INT_SRC_CLEAR:
 600         s->intr &= ~value;
 601         tusb_intr_update(s);
 602         break;
 603     case TUSB_INT_MASK:
 604         s->mask = value;
 605         tusb_intr_update(s);
 606         break;
 607
 608     case TUSB_GPIO_CONF:
 609         s->gpio_config = value;
 610         break;
 611     case TUSB_DMA_REQ_CONF:
 612         s->dma_config = value;
 613         break;
 614     case TUSB_EP0_CONF:
 615         s->ep0_config = value & 0x1ff;
 616         musb_set_size(s->musb, 0, TUSB_EP0_CONFIG_XFR_SIZE(value),
 617                         value & TUSB_EP0_CONFIG_DIR_TX);
 618         break;
 619     case TUSB_EP_IN_SIZE ... (TUSB_EP_IN_SIZE + 0x3b):
 620         epnum = (offset - TUSB_EP_IN_SIZE) >> 2;
 621         s->tx_config[epnum] = value;
 622         musb_set_size(s->musb, epnum + 1, TUSB_EP_CONFIG_XFR_SIZE(value), 1);
 623         break;
 624     case TUSB_DMA_EP_MAP:
 625         s->dma_map = value;
 626         break;
 627     case TUSB_EP_OUT_SIZE ... (TUSB_EP_OUT_SIZE + 0x3b):
 628         epnum = (offset - TUSB_EP_OUT_SIZE) >> 2;
 629         s->rx_config[epnum] = value;
 630         musb_set_size(s->musb, epnum + 1, TUSB_EP_CONFIG_XFR_SIZE(value), 0);
 631         break;
 632     case TUSB_EP_MAX_PACKET_SIZE_OFFSET ...
 633             (TUSB_EP_MAX_PACKET_SIZE_OFFSET + 0x3b):
 634         epnum = (offset - TUSB_EP_MAX_PACKET_SIZE_OFFSET) >> 2;
 635         return;         /* TODO */
 636     case TUSB_WAIT_COUNT:
 637         return;         /* TODO */
 638
 639     case TUSB_SCRATCH_PAD:
 640         s->scratch = value;
 641         break;
 642
 643     case TUSB_PROD_TEST_RESET:
 644         s->test_reset = value;
 645         break;
 646
 647     default:
 648         printf("%s: unknown register at %03x\n", __FUNCTION__, offset);
 649         return;
 650     }
 651 }
 652
 653 static CPUReadMemoryFunc *tusb_async_readfn[] = {
 654     tusb_async_readb,
 655     tusb_async_readh,
 656     tusb_async_readw,
 657 };
 658
 659 static CPUWriteMemoryFunc *tusb_async_writefn[] = {
 660     tusb_async_writeb,
 661     tusb_async_writeh,
 662     tusb_async_writew,
 663 };
 664
 665 static void tusb_otg_tick(void *opaque)
 666 {
 667     TUSBState *s = (TUSBState *) opaque;
 668
 669     s->otg_timer_val = 0;
 670     s->intr |= TUSB_INT_SRC_OTG_TIMEOUT;
 671     tusb_intr_update(s);
 672 }
 673
 674 static void tusb_power_tick(void *opaque)
 675 {
 676     TUSBState *s = (TUSBState *) opaque;
 677
 678     if (s->power) {
 679         s->intr_ok = ~0;
 680         tusb_intr_update(s);
 681     }
 682 }
 683
 684 static void tusb_musb_core_intr(void *opaque, int source, int level)
 685 {
 686     TUSBState *s = (TUSBState *) opaque;
 687     uint16_t otg_status = s->otg_status;
 688
 689     switch (source) {
 690     case musb_set_vbus:
 691         if (level)
 692             otg_status |= TUSB_DEV_OTG_STAT_VBUS_VALID;
 693         else
 694             otg_status &= ~TUSB_DEV_OTG_STAT_VBUS_VALID;
 695
 696         /* XXX: only if TUSB_PHY_OTG_CTRL_OTG_VBUS_DET_EN set?  */
 697         /* XXX: only if TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN set?  */
 698         if (s->otg_status != otg_status) {
 699             s->otg_status = otg_status;
 700             s->intr |= TUSB_INT_SRC_VBUS_SENSE_CHNG;
 701             tusb_intr_update(s);
 702         }
 703         break;
 704
 705     case musb_set_session:
 706         /* XXX: only if TUSB_PHY_OTG_CTRL_OTG_SESS_END_EN set?  */
 707         /* XXX: only if TUSB_PRCM_MNGMT_OTG_SESS_END_EN set?  */
 708         if (level) {
 709             s->otg_status |= TUSB_DEV_OTG_STAT_SESS_VALID;
 710             s->otg_status &= ~TUSB_DEV_OTG_STAT_SESS_END;
 711         } else {
 712             s->otg_status &= ~TUSB_DEV_OTG_STAT_SESS_VALID;
 713             s->otg_status |= TUSB_DEV_OTG_STAT_SESS_END;
 714         }
 715
 716         /* XXX: some IRQ or anything?  */
 717         break;
 718
 719     case musb_irq_tx:
 720     case musb_irq_rx:
 721         s->usbip_intr = musb_core_intr_get(s->musb);
 722         /* Fall through.  */
 723     default:
 724         if (level)
 725             s->intr |= 1 << source;
 726         else
 727             s->intr &= ~(1 << source);
 728         tusb_intr_update(s);
 729         break;
 730     }
 731 }
 732
 733 TUSBState *tusb6010_init(qemu_irq intr)
 734 {
 735     TUSBState *s = qemu_mallocz(sizeof(*s));
 736
 737     s->test_reset = TUSB_PROD_TEST_RESET_VAL;
 738     s->host_mode = 0;
 739     s->dev_config = 0;
 740     s->otg_status = 0;  /* !TUSB_DEV_OTG_STAT_ID_STATUS means host mode */
 741     s->power = 0;
 742     s->mask = 0xffffffff;
 743     s->intr = 0x00000000;
 744     s->otg_timer_val = 0;
 745     s->iomemtype[1] = cpu_register_io_memory(tusb_async_readfn,
 746                     tusb_async_writefn, s);
 747     s->irq = intr;
 748     s->otg_timer = qemu_new_timer(vm_clock, tusb_otg_tick, s);
 749     s->pwr_timer = qemu_new_timer(vm_clock, tusb_power_tick, s);
 750     s->musb = musb_init(qemu_allocate_irqs(tusb_musb_core_intr, s,
 751                             __musb_irq_max));
 752
 753     return s;
 754 }
 755
 756 void tusb6010_power(TUSBState *s, int on)
 757 {
 758     if (!on)
 759         s->power = 0;
 760     else if (!s->power && on) {
 761         s->power = 1;
 762
 763         /* Pull the interrupt down after TUSB6010 comes up.  */
 764         s->intr_ok = 0;
 765         tusb_intr_update(s);
 766         qemu_mod_timer(s->pwr_timer,
 767                         qemu_get_clock(vm_clock) + ticks_per_sec / 2);
 768     }
 769 }