hw/usb/dev-serial.c

   1 /*
   2  * FTDI FT232BM Device emulation
   3  *
   4  * Copyright (c) 2006 CodeSourcery.
   5  * Copyright (c) 2008 Samuel Thibault <samuel.thibault@ens-lyon.org>
   6  * Written by Paul Brook, reused for FTDI by Samuel Thibault
   7  *
   8  * This code is licensed under the LGPL.
   9  */
  10
  11 #include "qemu-common.h"
  12 #include "qemu/error-report.h"
  13 #include "hw/usb.h"
  14 #include "hw/usb/desc.h"
  15 #include "sysemu/char.h"
  16
  17 //#define DEBUG_Serial
  18
  19 #ifdef DEBUG_Serial
  20 #define DPRINTF(fmt, ...) \
  21 do { printf("usb-serial: " fmt , ## __VA_ARGS__); } while (0)
  22 #else
  23 #define DPRINTF(fmt, ...) do {} while(0)
  24 #endif
  25
  26 #define RECV_BUF 384
  27
  28 /* Commands */
  29 #define FTDI_RESET              0
  30 #define FTDI_SET_MDM_CTRL       1
  31 #define FTDI_SET_FLOW_CTRL      2
  32 #define FTDI_SET_BAUD           3
  33 #define FTDI_SET_DATA           4
  34 #define FTDI_GET_MDM_ST         5
  35 #define FTDI_SET_EVENT_CHR      6
  36 #define FTDI_SET_ERROR_CHR      7
  37 #define FTDI_SET_LATENCY        9
  38 #define FTDI_GET_LATENCY        10
  39
  40 #define DeviceOutVendor ((USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_DEVICE)<<8)
  41 #define DeviceInVendor  ((USB_DIR_IN |USB_TYPE_VENDOR|USB_RECIP_DEVICE)<<8)
  42
  43 /* RESET */
  44
  45 #define FTDI_RESET_SIO  0
  46 #define FTDI_RESET_RX   1
  47 #define FTDI_RESET_TX   2
  48
  49 /* SET_MDM_CTRL */
  50
  51 #define FTDI_DTR        1
  52 #define FTDI_SET_DTR    (FTDI_DTR << 8)
  53 #define FTDI_RTS        2
  54 #define FTDI_SET_RTS    (FTDI_RTS << 8)
  55
  56 /* SET_FLOW_CTRL */
  57
  58 #define FTDI_RTS_CTS_HS         1
  59 #define FTDI_DTR_DSR_HS         2
  60 #define FTDI_XON_XOFF_HS        4
  61
  62 /* SET_DATA */
  63
  64 #define FTDI_PARITY     (0x7 << 8)
  65 #define FTDI_ODD        (0x1 << 8)
  66 #define FTDI_EVEN       (0x2 << 8)
  67 #define FTDI_MARK       (0x3 << 8)
  68 #define FTDI_SPACE      (0x4 << 8)
  69
  70 #define FTDI_STOP       (0x3 << 11)
  71 #define FTDI_STOP1      (0x0 << 11)
  72 #define FTDI_STOP15     (0x1 << 11)
  73 #define FTDI_STOP2      (0x2 << 11)
  74
  75 /* GET_MDM_ST */
  76 /* TODO: should be sent every 40ms */
  77 #define FTDI_CTS  (1<<4)        // CTS line status
  78 #define FTDI_DSR  (1<<5)        // DSR line status
  79 #define FTDI_RI   (1<<6)        // RI line status
  80 #define FTDI_RLSD (1<<7)        // Receive Line Signal Detect
  81
  82 /* Status */
  83
  84 #define FTDI_DR   (1<<0)        // Data Ready
  85 #define FTDI_OE   (1<<1)        // Overrun Err
  86 #define FTDI_PE   (1<<2)        // Parity Err
  87 #define FTDI_FE   (1<<3)        // Framing Err
  88 #define FTDI_BI   (1<<4)        // Break Interrupt
  89 #define FTDI_THRE (1<<5)        // Transmitter Holding Register
  90 #define FTDI_TEMT (1<<6)        // Transmitter Empty
  91 #define FTDI_FIFO (1<<7)        // Error in FIFO
  92
  93 typedef struct {
  94     USBDevice dev;
  95     uint8_t recv_buf[RECV_BUF];
  96     uint16_t recv_ptr;
  97     uint16_t recv_used;
  98     uint8_t event_chr;
  99     uint8_t error_chr;
 100     uint8_t event_trigger;
 101     QEMUSerialSetParams params;
 102     int latency;        /* ms */
 103     CharDriverState *cs;
 104 } USBSerialState;
 105
 106 enum {
 107     STR_MANUFACTURER = 1,
 108     STR_PRODUCT_SERIAL,
 109     STR_PRODUCT_BRAILLE,
 110     STR_SERIALNUMBER,
 111 };
 112
 113 static const USBDescStrings desc_strings = {
 114     [STR_MANUFACTURER]    = "QEMU",
 115     [STR_PRODUCT_SERIAL]  = "QEMU USB SERIAL",
 116     [STR_PRODUCT_BRAILLE] = "QEMU USB BAUM BRAILLE",
 117     [STR_SERIALNUMBER]    = "1",
 118 };
 119
 120 static const USBDescIface desc_iface0 = {
 121     .bInterfaceNumber              = 0,
 122     .bNumEndpoints                 = 2,
 123     .bInterfaceClass               = 0xff,
 124     .bInterfaceSubClass            = 0xff,
 125     .bInterfaceProtocol            = 0xff,
 126     .eps = (USBDescEndpoint[]) {
 127         {
 128             .bEndpointAddress      = USB_DIR_IN | 0x01,
 129             .bmAttributes          = USB_ENDPOINT_XFER_BULK,
 130             .wMaxPacketSize        = 64,
 131         },{
 132             .bEndpointAddress      = USB_DIR_OUT | 0x02,
 133             .bmAttributes          = USB_ENDPOINT_XFER_BULK,
 134             .wMaxPacketSize        = 64,
 135         },
 136     }
 137 };
 138
 139 static const USBDescDevice desc_device = {
 140     .bcdUSB                        = 0x0200,
 141     .bMaxPacketSize0               = 8,
 142     .bNumConfigurations            = 1,
 143     .confs = (USBDescConfig[]) {
 144         {
 145             .bNumInterfaces        = 1,
 146             .bConfigurationValue   = 1,
 147             .bmAttributes          = 0x80,
 148             .bMaxPower             = 50,
 149             .nif = 1,
 150             .ifs = &desc_iface0,
 151         },
 152     },
 153 };
 154
 155 static const USBDesc desc_serial = {
 156     .id = {
 157         .idVendor          = 0x0403,
 158         .idProduct         = 0x6001,
 159         .bcdDevice         = 0x0400,
 160         .iManufacturer     = STR_MANUFACTURER,
 161         .iProduct          = STR_PRODUCT_SERIAL,
 162         .iSerialNumber     = STR_SERIALNUMBER,
 163     },
 164     .full = &desc_device,
 165     .str  = desc_strings,
 166 };
 167
 168 static const USBDesc desc_braille = {
 169     .id = {
 170         .idVendor          = 0x0403,
 171         .idProduct         = 0xfe72,
 172         .bcdDevice         = 0x0400,
 173         .iManufacturer     = STR_MANUFACTURER,
 174         .iProduct          = STR_PRODUCT_BRAILLE,
 175         .iSerialNumber     = STR_SERIALNUMBER,
 176     },
 177     .full = &desc_device,
 178     .str  = desc_strings,
 179 };
 180
 181 static void usb_serial_reset(USBSerialState *s)
 182 {
 183     /* TODO: Set flow control to none */
 184     s->event_chr = 0x0d;
 185     s->event_trigger = 0;
 186     s->recv_ptr = 0;
 187     s->recv_used = 0;
 188     /* TODO: purge in char driver */
 189 }
 190
 191 static void usb_serial_handle_reset(USBDevice *dev)
 192 {
 193     USBSerialState *s = (USBSerialState *)dev;
 194
 195     DPRINTF("Reset\n");
 196
 197     usb_serial_reset(s);
 198     /* TODO: Reset char device, send BREAK? */
 199 }
 200
 201 static uint8_t usb_get_modem_lines(USBSerialState *s)
 202 {
 203     int flags;
 204     uint8_t ret;
 205
 206     if (qemu_chr_fe_ioctl(s->cs, CHR_IOCTL_SERIAL_GET_TIOCM, &flags) == -ENOTSUP)
 207         return FTDI_CTS|FTDI_DSR|FTDI_RLSD;
 208
 209     ret = 0;
 210     if (flags & CHR_TIOCM_CTS)
 211         ret |= FTDI_CTS;
 212     if (flags & CHR_TIOCM_DSR)
 213         ret |= FTDI_DSR;
 214     if (flags & CHR_TIOCM_RI)
 215         ret |= FTDI_RI;
 216     if (flags & CHR_TIOCM_CAR)
 217         ret |= FTDI_RLSD;
 218
 219     return ret;
 220 }
 221
 222 static void usb_serial_handle_control(USBDevice *dev, USBPacket *p,
 223                int request, int value, int index, int length, uint8_t *data)
 224 {
 225     USBSerialState *s = (USBSerialState *)dev;
 226     int ret;
 227
 228     DPRINTF("got control %x, value %x\n",request, value);
 229     ret = usb_desc_handle_control(dev, p, request, value, index, length, data);
 230     if (ret >= 0) {
 231         return;
 232     }
 233
 234     switch (request) {
 235     case EndpointOutRequest | USB_REQ_CLEAR_FEATURE:
 236         break;
 237
 238         /* Class specific requests.  */
 239     case DeviceOutVendor | FTDI_RESET:
 240         switch (value) {
 241         case FTDI_RESET_SIO:
 242             usb_serial_reset(s);
 243             break;
 244         case FTDI_RESET_RX:
 245             s->recv_ptr = 0;
 246             s->recv_used = 0;
 247             /* TODO: purge from char device */
 248             break;
 249         case FTDI_RESET_TX:
 250             /* TODO: purge from char device */
 251             break;
 252         }
 253         break;
 254     case DeviceOutVendor | FTDI_SET_MDM_CTRL:
 255     {
 256         static int flags;
 257         qemu_chr_fe_ioctl(s->cs,CHR_IOCTL_SERIAL_GET_TIOCM, &flags);
 258         if (value & FTDI_SET_RTS) {
 259             if (value & FTDI_RTS)
 260                 flags |= CHR_TIOCM_RTS;
 261             else
 262                 flags &= ~CHR_TIOCM_RTS;
 263         }
 264         if (value & FTDI_SET_DTR) {
 265             if (value & FTDI_DTR)
 266                 flags |= CHR_TIOCM_DTR;
 267             else
 268                 flags &= ~CHR_TIOCM_DTR;
 269         }
 270         qemu_chr_fe_ioctl(s->cs,CHR_IOCTL_SERIAL_SET_TIOCM, &flags);
 271         break;
 272     }
 273     case DeviceOutVendor | FTDI_SET_FLOW_CTRL:
 274         /* TODO: ioctl */
 275         break;
 276     case DeviceOutVendor | FTDI_SET_BAUD: {
 277         static const int subdivisors8[8] = { 0, 4, 2, 1, 3, 5, 6, 7 };
 278         int subdivisor8 = subdivisors8[((value & 0xc000) >> 14)
 279                                      | ((index & 1) << 2)];
 280         int divisor = value & 0x3fff;
 281
 282         /* chip special cases */
 283         if (divisor == 1 && subdivisor8 == 0)
 284             subdivisor8 = 4;
 285         if (divisor == 0 && subdivisor8 == 0)
 286             divisor = 1;
 287
 288         s->params.speed = (48000000 / 2) / (8 * divisor + subdivisor8);
 289         qemu_chr_fe_ioctl(s->cs, CHR_IOCTL_SERIAL_SET_PARAMS, &s->params);
 290         break;
 291     }
 292     case DeviceOutVendor | FTDI_SET_DATA:
 293         switch (value & FTDI_PARITY) {
 294             case 0:
 295                 s->params.parity = 'N';
 296                 break;
 297             case FTDI_ODD:
 298                 s->params.parity = 'O';
 299                 break;
 300             case FTDI_EVEN:
 301                 s->params.parity = 'E';
 302                 break;
 303             default:
 304                 DPRINTF("unsupported parity %d\n", value & FTDI_PARITY);
 305                 goto fail;
 306         }
 307         switch (value & FTDI_STOP) {
 308             case FTDI_STOP1:
 309                 s->params.stop_bits = 1;
 310                 break;
 311             case FTDI_STOP2:
 312                 s->params.stop_bits = 2;
 313                 break;
 314             default:
 315                 DPRINTF("unsupported stop bits %d\n", value & FTDI_STOP);
 316                 goto fail;
 317         }
 318         qemu_chr_fe_ioctl(s->cs, CHR_IOCTL_SERIAL_SET_PARAMS, &s->params);
 319         /* TODO: TX ON/OFF */
 320         break;
 321     case DeviceInVendor | FTDI_GET_MDM_ST:
 322         data[0] = usb_get_modem_lines(s) | 1;
 323         data[1] = 0;
 324         p->actual_length = 2;
 325         break;
 326     case DeviceOutVendor | FTDI_SET_EVENT_CHR:
 327         /* TODO: handle it */
 328         s->event_chr = value;
 329         break;
 330     case DeviceOutVendor | FTDI_SET_ERROR_CHR:
 331         /* TODO: handle it */
 332         s->error_chr = value;
 333         break;
 334     case DeviceOutVendor | FTDI_SET_LATENCY:
 335         s->latency = value;
 336         break;
 337     case DeviceInVendor | FTDI_GET_LATENCY:
 338         data[0] = s->latency;
 339         p->actual_length = 1;
 340         break;
 341     default:
 342     fail:
 343         DPRINTF("got unsupported/bogus control %x, value %x\n", request, value);
 344         p->status = USB_RET_STALL;
 345         break;
 346     }
 347 }
 348
 349 static void usb_serial_handle_data(USBDevice *dev, USBPacket *p)
 350 {
 351     USBSerialState *s = (USBSerialState *)dev;
 352     uint8_t devep = p->ep->nr;
 353     struct iovec *iov;
 354     uint8_t header[2];
 355     int i, first_len, len;
 356
 357     switch (p->pid) {
 358     case USB_TOKEN_OUT:
 359         if (devep != 2)
 360             goto fail;
 361         for (i = 0; i < p->iov.niov; i++) {
 362             iov = p->iov.iov + i;
 363             qemu_chr_fe_write(s->cs, iov->iov_base, iov->iov_len);
 364         }
 365         p->actual_length = p->iov.size;
 366         break;
 367
 368     case USB_TOKEN_IN:
 369         if (devep != 1)
 370             goto fail;
 371         first_len = RECV_BUF - s->recv_ptr;
 372         len = p->iov.size;
 373         if (len <= 2) {
 374             p->status = USB_RET_NAK;
 375             break;
 376         }
 377         header[0] = usb_get_modem_lines(s) | 1;
 378         /* We do not have the uart details */
 379         /* handle serial break */
 380         if (s->event_trigger && s->event_trigger & FTDI_BI) {
 381             s->event_trigger &= ~FTDI_BI;
 382             header[1] = FTDI_BI;
 383             usb_packet_copy(p, header, 2);
 384             break;
 385         } else {
 386             header[1] = 0;
 387         }
 388         len -= 2;
 389         if (len > s->recv_used)
 390             len = s->recv_used;
 391         if (!len) {
 392             p->status = USB_RET_NAK;
 393             break;
 394         }
 395         if (first_len > len)
 396             first_len = len;
 397         usb_packet_copy(p, header, 2);
 398         usb_packet_copy(p, s->recv_buf + s->recv_ptr, first_len);
 399         if (len > first_len)
 400             usb_packet_copy(p, s->recv_buf, len - first_len);
 401         s->recv_used -= len;
 402         s->recv_ptr = (s->recv_ptr + len) % RECV_BUF;
 403         break;
 404
 405     default:
 406         DPRINTF("Bad token\n");
 407     fail:
 408         p->status = USB_RET_STALL;
 409         break;
 410     }
 411 }
 412
 413 static int usb_serial_can_read(void *opaque)
 414 {
 415     USBSerialState *s = opaque;
 416
 417     if (!s->dev.attached) {
 418         return 0;
 419     }
 420     return RECV_BUF - s->recv_used;
 421 }
 422
 423 static void usb_serial_read(void *opaque, const uint8_t *buf, int size)
 424 {
 425     USBSerialState *s = opaque;
 426     int first_size, start;
 427
 428     /* room in the buffer? */
 429     if (size > (RECV_BUF - s->recv_used))
 430         size = RECV_BUF - s->recv_used;
 431
 432     start = s->recv_ptr + s->recv_used;
 433     if (start < RECV_BUF) {
 434         /* copy data to end of buffer */
 435         first_size = RECV_BUF - start;
 436         if (first_size > size)
 437             first_size = size;
 438
 439         memcpy(s->recv_buf + start, buf, first_size);
 440
 441         /* wrap around to front if needed */
 442         if (size > first_size)
 443             memcpy(s->recv_buf, buf + first_size, size - first_size);
 444     } else {
 445         start -= RECV_BUF;
 446         memcpy(s->recv_buf + start, buf, size);
 447     }
 448     s->recv_used += size;
 449 }
 450
 451 static void usb_serial_event(void *opaque, int event)
 452 {
 453     USBSerialState *s = opaque;
 454
 455     switch (event) {
 456         case CHR_EVENT_BREAK:
 457             s->event_trigger |= FTDI_BI;
 458             break;
 459         case CHR_EVENT_FOCUS:
 460             break;
 461         case CHR_EVENT_OPENED:
 462             if (!s->dev.attached) {
 463                 usb_device_attach(&s->dev);
 464             }
 465             break;
 466         case CHR_EVENT_CLOSED:
 467             if (s->dev.attached) {
 468                 usb_device_detach(&s->dev);
 469             }
 470             break;
 471     }
 472 }
 473
 474 static int usb_serial_initfn(USBDevice *dev)
 475 {
 476     USBSerialState *s = DO_UPCAST(USBSerialState, dev, dev);
 477
 478     usb_desc_create_serial(dev);
 479     usb_desc_init(dev);
 480     dev->auto_attach = 0;
 481
 482     if (!s->cs) {
 483         error_report("Property chardev is required");
 484         return -1;
 485     }
 486
 487     qemu_chr_add_handlers(s->cs, usb_serial_can_read, usb_serial_read,
 488                           usb_serial_event, s);
 489     usb_serial_handle_reset(dev);
 490
 491     if (s->cs->be_open && !dev->attached) {
 492         usb_device_attach(dev);
 493     }
 494     return 0;
 495 }
 496
 497 static USBDevice *usb_serial_init(USBBus *bus, const char *filename)
 498 {
 499     USBDevice *dev;
 500     CharDriverState *cdrv;
 501     uint32_t vendorid = 0, productid = 0;
 502     char label[32];
 503     static int index;
 504
 505     while (*filename && *filename != ':') {
 506         const char *p;
 507         char *e;
 508         if (strstart(filename, "vendorid=", &p)) {
 509             vendorid = strtol(p, &e, 16);
 510             if (e == p || (*e && *e != ',' && *e != ':')) {
 511                 error_report("bogus vendor ID %s", p);
 512                 return NULL;
 513             }
 514             filename = e;
 515         } else if (strstart(filename, "productid=", &p)) {
 516             productid = strtol(p, &e, 16);
 517             if (e == p || (*e && *e != ',' && *e != ':')) {
 518                 error_report("bogus product ID %s", p);
 519                 return NULL;
 520             }
 521             filename = e;
 522         } else {
 523             error_report("unrecognized serial USB option %s", filename);
 524             return NULL;
 525         }
 526         while(*filename == ',')
 527             filename++;
 528     }
 529     if (!*filename) {
 530         error_report("character device specification needed");
 531         return NULL;
 532     }
 533     filename++;
 534
 535     snprintf(label, sizeof(label), "usbserial%d", index++);
 536     cdrv = qemu_chr_new(label, filename, NULL);
 537     if (!cdrv)
 538         return NULL;
 539
 540     dev = usb_create(bus, "usb-serial");
 541     if (!dev) {
 542         return NULL;
 543     }
 544     qdev_prop_set_chr(&dev->qdev, "chardev", cdrv);
 545     if (vendorid)
 546         qdev_prop_set_uint16(&dev->qdev, "vendorid", vendorid);
 547     if (productid)
 548         qdev_prop_set_uint16(&dev->qdev, "productid", productid);
 549     qdev_init_nofail(&dev->qdev);
 550
 551     return dev;
 552 }
 553
 554 static USBDevice *usb_braille_init(USBBus *bus, const char *unused)
 555 {
 556     USBDevice *dev;
 557     CharDriverState *cdrv;
 558
 559     cdrv = qemu_chr_new("braille", "braille", NULL);
 560     if (!cdrv)
 561         return NULL;
 562
 563     dev = usb_create(bus, "usb-braille");
 564     qdev_prop_set_chr(&dev->qdev, "chardev", cdrv);
 565     qdev_init_nofail(&dev->qdev);
 566
 567     return dev;
 568 }
 569
 570 static const VMStateDescription vmstate_usb_serial = {
 571     .name = "usb-serial",
 572     .unmigratable = 1,
 573 };
 574
 575 static Property serial_properties[] = {
 576     DEFINE_PROP_CHR("chardev", USBSerialState, cs),
 577     DEFINE_PROP_END_OF_LIST(),
 578 };
 579
 580 static void usb_serial_class_initfn(ObjectClass *klass, void *data)
 581 {
 582     DeviceClass *dc = DEVICE_CLASS(klass);
 583     USBDeviceClass *uc = USB_DEVICE_CLASS(klass);
 584
 585     uc->init = usb_serial_initfn;
 586     uc->product_desc   = "QEMU USB Serial";
 587     uc->usb_desc       = &desc_serial;
 588     uc->handle_reset   = usb_serial_handle_reset;
 589     uc->handle_control = usb_serial_handle_control;
 590     uc->handle_data    = usb_serial_handle_data;
 591     dc->vmsd = &vmstate_usb_serial;
 592     dc->props = serial_properties;
 593 }
 594
 595 static const TypeInfo serial_info = {
 596     .name          = "usb-serial",
 597     .parent        = TYPE_USB_DEVICE,
 598     .instance_size = sizeof(USBSerialState),
 599     .class_init    = usb_serial_class_initfn,
 600 };
 601
 602 static Property braille_properties[] = {
 603     DEFINE_PROP_CHR("chardev", USBSerialState, cs),
 604     DEFINE_PROP_END_OF_LIST(),
 605 };
 606
 607 static void usb_braille_class_initfn(ObjectClass *klass, void *data)
 608 {
 609     DeviceClass *dc = DEVICE_CLASS(klass);
 610     USBDeviceClass *uc = USB_DEVICE_CLASS(klass);
 611
 612     uc->init           = usb_serial_initfn;
 613     uc->product_desc   = "QEMU USB Braille";
 614     uc->usb_desc       = &desc_braille;
 615     uc->handle_reset   = usb_serial_handle_reset;
 616     uc->handle_control = usb_serial_handle_control;
 617     uc->handle_data    = usb_serial_handle_data;
 618     dc->vmsd = &vmstate_usb_serial;
 619     dc->props = braille_properties;
 620 }
 621
 622 static const TypeInfo braille_info = {
 623     .name          = "usb-braille",
 624     .parent        = TYPE_USB_DEVICE,
 625     .instance_size = sizeof(USBSerialState),
 626     .class_init    = usb_braille_class_initfn,
 627 };
 628
 629 static void usb_serial_register_types(void)
 630 {
 631     type_register_static(&serial_info);
 632     usb_legacy_register("usb-serial", "serial", usb_serial_init);
 633     type_register_static(&braille_info);
 634     usb_legacy_register("usb-braille", "braille", usb_braille_init);
 635 }
 636
 637 type_init(usb_serial_register_types)