hw/pl061.c

   1 /*
   2  * Arm PrimeCell PL061 General Purpose IO with additional
   3  * Luminary Micro Stellaris bits.
   4  *
   5  * Copyright (c) 2007 CodeSourcery.
   6  * Written by Paul Brook
   7  *
   8  * This code is licenced under the GPL.
   9  */
  10
  11 #include "sysbus.h"
  12
  13 //#define DEBUG_PL061 1
  14
  15 #ifdef DEBUG_PL061
  16 #define DPRINTF(fmt, ...) \
  17 do { printf("pl061: " fmt , ## __VA_ARGS__); } while (0)
  18 #define BADF(fmt, ...) \
  19 do { fprintf(stderr, "pl061: error: " fmt , ## __VA_ARGS__); exit(1);} while (0)
  20 #else
  21 #define DPRINTF(fmt, ...) do {} while(0)
  22 #define BADF(fmt, ...) \
  23 do { fprintf(stderr, "pl061: error: " fmt , ## __VA_ARGS__);} while (0)
  24 #endif
  25
  26 static const uint8_t pl061_id[12] =
  27   { 0x00, 0x00, 0x00, 0x00, 0x61, 0x00, 0x18, 0x01, 0x0d, 0xf0, 0x05, 0xb1 };
  28
  29 typedef struct {
  30     SysBusDevice busdev;
  31     int locked;
  32     uint8_t data;
  33     uint8_t old_data;
  34     uint8_t dir;
  35     uint8_t isense;
  36     uint8_t ibe;
  37     uint8_t iev;
  38     uint8_t im;
  39     uint8_t istate;
  40     uint8_t afsel;
  41     uint8_t dr2r;
  42     uint8_t dr4r;
  43     uint8_t dr8r;
  44     uint8_t odr;
  45     uint8_t pur;
  46     uint8_t pdr;
  47     uint8_t slr;
  48     uint8_t den;
  49     uint8_t cr;
  50     uint8_t float_high;
  51     qemu_irq irq;
  52     qemu_irq out[8];
  53 } pl061_state;
  54
  55 static void pl061_update(pl061_state *s)
  56 {
  57     uint8_t changed;
  58     uint8_t mask;
  59     uint8_t out;
  60     int i;
  61
  62     /* Outputs float high.  */
  63     /* FIXME: This is board dependent.  */
  64     out = (s->data & s->dir) | ~s->dir;
  65     changed = s->old_data ^ out;
  66     if (!changed)
  67         return;
  68
  69     s->old_data = out;
  70     for (i = 0; i < 8; i++) {
  71         mask = 1 << i;
  72         if ((changed & mask) && s->out) {
  73             DPRINTF("Set output %d = %d\n", i, (out & mask) != 0);
  74             qemu_set_irq(s->out[i], (out & mask) != 0);
  75         }
  76     }
  77
  78     /* FIXME: Implement input interrupts.  */
  79 }
  80
  81 static uint32_t pl061_read(void *opaque, target_phys_addr_t offset)
  82 {
  83     pl061_state *s = (pl061_state *)opaque;
  84
  85     if (offset >= 0xfd0 && offset < 0x1000) {
  86         return pl061_id[(offset - 0xfd0) >> 2];
  87     }
  88     if (offset < 0x400) {
  89         return s->data & (offset >> 2);
  90     }
  91     switch (offset) {
  92     case 0x400: /* Direction */
  93         return s->dir;
  94     case 0x404: /* Interrupt sense */
  95         return s->isense;
  96     case 0x408: /* Interrupt both edges */
  97         return s->ibe;
  98     case 0x40c: /* Interupt event */
  99         return s->iev;
 100     case 0x410: /* Interrupt mask */
 101         return s->im;
 102     case 0x414: /* Raw interrupt status */
 103         return s->istate;
 104     case 0x418: /* Masked interrupt status */
 105         return s->istate | s->im;
 106     case 0x420: /* Alternate function select */
 107         return s->afsel;
 108     case 0x500: /* 2mA drive */
 109         return s->dr2r;
 110     case 0x504: /* 4mA drive */
 111         return s->dr4r;
 112     case 0x508: /* 8mA drive */
 113         return s->dr8r;
 114     case 0x50c: /* Open drain */
 115         return s->odr;
 116     case 0x510: /* Pull-up */
 117         return s->pur;
 118     case 0x514: /* Pull-down */
 119         return s->pdr;
 120     case 0x518: /* Slew rate control */
 121         return s->slr;
 122     case 0x51c: /* Digital enable */
 123         return s->den;
 124     case 0x520: /* Lock */
 125         return s->locked;
 126     case 0x524: /* Commit */
 127         return s->cr;
 128     default:
 129         hw_error("pl061_read: Bad offset %x\n", (int)offset);
 130         return 0;
 131     }
 132 }
 133
 134 static void pl061_write(void *opaque, target_phys_addr_t offset,
 135                         uint32_t value)
 136 {
 137     pl061_state *s = (pl061_state *)opaque;
 138     uint8_t mask;
 139
 140     if (offset < 0x400) {
 141         mask = (offset >> 2) & s->dir;
 142         s->data = (s->data & ~mask) | (value & mask);
 143         pl061_update(s);
 144         return;
 145     }
 146     switch (offset) {
 147     case 0x400: /* Direction */
 148         s->dir = value;
 149         break;
 150     case 0x404: /* Interrupt sense */
 151         s->isense = value;
 152         break;
 153     case 0x408: /* Interrupt both edges */
 154         s->ibe = value;
 155         break;
 156     case 0x40c: /* Interupt event */
 157         s->iev = value;
 158         break;
 159     case 0x410: /* Interrupt mask */
 160         s->im = value;
 161         break;
 162     case 0x41c: /* Interrupt clear */
 163         s->istate &= ~value;
 164         break;
 165     case 0x420: /* Alternate function select */
 166         mask = s->cr;
 167         s->afsel = (s->afsel & ~mask) | (value & mask);
 168         break;
 169     case 0x500: /* 2mA drive */
 170         s->dr2r = value;
 171         break;
 172     case 0x504: /* 4mA drive */
 173         s->dr4r = value;
 174         break;
 175     case 0x508: /* 8mA drive */
 176         s->dr8r = value;
 177         break;
 178     case 0x50c: /* Open drain */
 179         s->odr = value;
 180         break;
 181     case 0x510: /* Pull-up */
 182         s->pur = value;
 183         break;
 184     case 0x514: /* Pull-down */
 185         s->pdr = value;
 186         break;
 187     case 0x518: /* Slew rate control */
 188         s->slr = value;
 189         break;
 190     case 0x51c: /* Digital enable */
 191         s->den = value;
 192         break;
 193     case 0x520: /* Lock */
 194         s->locked = (value != 0xacce551);
 195         break;
 196     case 0x524: /* Commit */
 197         if (!s->locked)
 198             s->cr = value;
 199         break;
 200     default:
 201         hw_error("pl061_write: Bad offset %x\n", (int)offset);
 202     }
 203     pl061_update(s);
 204 }
 205
 206 static void pl061_reset(pl061_state *s)
 207 {
 208   s->locked = 1;
 209   s->cr = 0xff;
 210 }
 211
 212 static void pl061_set_irq(void * opaque, int irq, int level)
 213 {
 214     pl061_state *s = (pl061_state *)opaque;
 215     uint8_t mask;
 216
 217     mask = 1 << irq;
 218     if ((s->dir & mask) == 0) {
 219         s->data &= ~mask;
 220         if (level)
 221             s->data |= mask;
 222         pl061_update(s);
 223     }
 224 }
 225
 226 static CPUReadMemoryFunc * const pl061_readfn[] = {
 227    pl061_read,
 228    pl061_read,
 229    pl061_read
 230 };
 231
 232 static CPUWriteMemoryFunc * const pl061_writefn[] = {
 233    pl061_write,
 234    pl061_write,
 235    pl061_write
 236 };
 237
 238 static void pl061_save(QEMUFile *f, void *opaque)
 239 {
 240     pl061_state *s = (pl061_state *)opaque;
 241
 242     qemu_put_be32(f, s->locked);
 243     qemu_put_be32(f, s->data);
 244     qemu_put_be32(f, s->old_data);
 245     qemu_put_be32(f, s->dir);
 246     qemu_put_be32(f, s->isense);
 247     qemu_put_be32(f, s->ibe);
 248     qemu_put_be32(f, s->iev);
 249     qemu_put_be32(f, s->im);
 250     qemu_put_be32(f, s->istate);
 251     qemu_put_be32(f, s->afsel);
 252     qemu_put_be32(f, s->dr2r);
 253     qemu_put_be32(f, s->dr4r);
 254     qemu_put_be32(f, s->dr8r);
 255     qemu_put_be32(f, s->odr);
 256     qemu_put_be32(f, s->pur);
 257     qemu_put_be32(f, s->pdr);
 258     qemu_put_be32(f, s->slr);
 259     qemu_put_be32(f, s->den);
 260     qemu_put_be32(f, s->cr);
 261     qemu_put_be32(f, s->float_high);
 262 }
 263
 264 static int pl061_load(QEMUFile *f, void *opaque, int version_id)
 265 {
 266     pl061_state *s = (pl061_state *)opaque;
 267     if (version_id != 1)
 268         return -EINVAL;
 269
 270     s->locked = qemu_get_be32(f);
 271     s->data = qemu_get_be32(f);
 272     s->old_data = qemu_get_be32(f);
 273     s->dir = qemu_get_be32(f);
 274     s->isense = qemu_get_be32(f);
 275     s->ibe = qemu_get_be32(f);
 276     s->iev = qemu_get_be32(f);
 277     s->im = qemu_get_be32(f);
 278     s->istate = qemu_get_be32(f);
 279     s->afsel = qemu_get_be32(f);
 280     s->dr2r = qemu_get_be32(f);
 281     s->dr4r = qemu_get_be32(f);
 282     s->dr8r = qemu_get_be32(f);
 283     s->odr = qemu_get_be32(f);
 284     s->pur = qemu_get_be32(f);
 285     s->pdr = qemu_get_be32(f);
 286     s->slr = qemu_get_be32(f);
 287     s->den = qemu_get_be32(f);
 288     s->cr = qemu_get_be32(f);
 289     s->float_high = qemu_get_be32(f);
 290
 291     return 0;
 292 }
 293
 294 static int pl061_init(SysBusDevice *dev)
 295 {
 296     int iomemtype;
 297     pl061_state *s = FROM_SYSBUS(pl061_state, dev);
 298
 299     iomemtype = cpu_register_io_memory(pl061_readfn,
 300                                        pl061_writefn, s);
 301     sysbus_init_mmio(dev, 0x1000, iomemtype);
 302     sysbus_init_irq(dev, &s->irq);
 303     qdev_init_gpio_in(&dev->qdev, pl061_set_irq, 8);
 304     qdev_init_gpio_out(&dev->qdev, s->out, 8);
 305     pl061_reset(s);
 306     register_savevm(&dev->qdev, "pl061_gpio", -1, 1, pl061_save, pl061_load, s);
 307     return 0;
 308 }
 309
 310 static void pl061_register_devices(void)
 311 {
 312     sysbus_register_dev("pl061", sizeof(pl061_state),
 313                         pl061_init);
 314 }
 315
 316 device_init(pl061_register_devices)