drivers/ide/serverworks.c

   1 /*
   2  * Copyright (C) 1998-2000 Michel Aubry
   3  * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
   4  * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
   5  * Copyright (C) 2007-2010 Bartlomiej Zolnierkiewicz
   6  * Portions copyright (c) 2001 Sun Microsystems
   7  *
   8  *
   9  * RCC/ServerWorks IDE driver for Linux
  10  *
  11  *   OSB4: `Open South Bridge' IDE Interface (fn 1)
  12  *         supports UDMA mode 2 (33 MB/s)
  13  *
  14  *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
  15  *         all revisions support UDMA mode 4 (66 MB/s)
  16  *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
  17  *
  18  *         *** The CSB5 does not provide ANY register ***
  19  *         *** to detect 80-conductor cable presence. ***
  20  *
  21  *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
  22  *
  23  *   HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
  24  *   controller same as the CSB6. Single channel ATA100 only.
  25  *
  26  * Documentation:
  27  *      Available under NDA only. Errata info very hard to get.
  28  *
  29  */
  30
  31 #include <linux/types.h>
  32 #include <linux/module.h>
  33 #include <linux/kernel.h>
  34 #include <linux/pci.h>
  35 #include <linux/ide.h>
  36 #include <linux/init.h>
  37
  38 #include <asm/io.h>
  39
  40 #define DRV_NAME "serverworks"
  41
  42 #define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
  43 #define SVWKS_CSB6_REVISION     0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
  44
  45 /* Seagate Barracuda ATA IV Family drives in UDMA mode 5
  46  * can overrun their FIFOs when used with the CSB5 */
  47 static const char *svwks_bad_ata100[] = {
  48         "ST320011A",
  49         "ST340016A",
  50         "ST360021A",
  51         "ST380021A",
  52         NULL
  53 };
  54
  55 static int check_in_drive_lists (ide_drive_t *drive, const char **list)
  56 {
  57         char *m = (char *)&drive->id[ATA_ID_PROD];
  58
  59         while (*list)
  60                 if (!strcmp(*list++, m))
  61                         return 1;
  62         return 0;
  63 }
  64
  65 static u8 svwks_udma_filter(ide_drive_t *drive)
  66 {
  67         struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
  68
  69         if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
  70                 return 0x1f;
  71         } else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
  72                 return 0x07;
  73         } else {
  74                 u8 btr = 0, mode, mask;
  75
  76                 pci_read_config_byte(dev, 0x5A, &btr);
  77                 mode = btr & 0x3;
  78
  79                 /* If someone decides to do UDMA133 on CSB5 the same
  80                    issue will bite so be inclusive */
  81                 if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
  82                         mode = 2;
  83
  84                 switch(mode) {
  85                 case 3:  mask = 0x3f; break;
  86                 case 2:  mask = 0x1f; break;
  87                 case 1:  mask = 0x07; break;
  88                 default: mask = 0x00; break;
  89                 }
  90
  91                 return mask;
  92         }
  93 }
  94
  95 static u8 svwks_csb_check (struct pci_dev *dev)
  96 {
  97         switch (dev->device) {
  98                 case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
  99                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
 100                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
 101                 case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
 102                         return 1;
 103                 default:
 104                         break;
 105         }
 106         return 0;
 107 }
 108
 109 static void svwks_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 110 {
 111         static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
 112         static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
 113
 114         struct pci_dev *dev = to_pci_dev(hwif->dev);
 115         const u8 pio = drive->pio_mode - XFER_PIO_0;
 116
 117         pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
 118
 119         if (svwks_csb_check(dev)) {
 120                 u16 csb_pio = 0;
 121
 122                 pci_read_config_word(dev, 0x4a, &csb_pio);
 123
 124                 csb_pio &= ~(0x0f << (4 * drive->dn));
 125                 csb_pio |= (pio << (4 * drive->dn));
 126
 127                 pci_write_config_word(dev, 0x4a, csb_pio);
 128         }
 129 }
 130
 131 static void svwks_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 132 {
 133         static const u8 udma_modes[]            = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
 134         static const u8 dma_modes[]             = { 0x77, 0x21, 0x20 };
 135         static const u8 drive_pci2[]            = { 0x45, 0x44, 0x47, 0x46 };
 136
 137         struct pci_dev *dev     = to_pci_dev(hwif->dev);
 138         const u8 speed          = drive->dma_mode;
 139         u8 unit                 = drive->dn & 1;
 140
 141         u8 ultra_enable  = 0, ultra_timing = 0, dma_timing = 0;
 142
 143         pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
 144         pci_read_config_byte(dev, 0x54, &ultra_enable);
 145
 146         ultra_timing    &= ~(0x0F << (4*unit));
 147         ultra_enable    &= ~(0x01 << drive->dn);
 148
 149         if (speed >= XFER_UDMA_0) {
 150                 dma_timing   |= dma_modes[2];
 151                 ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
 152                 ultra_enable |= (0x01 << drive->dn);
 153         } else if (speed >= XFER_MW_DMA_0)
 154                 dma_timing   |= dma_modes[speed - XFER_MW_DMA_0];
 155
 156         pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
 157         pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
 158         pci_write_config_byte(dev, 0x54, ultra_enable);
 159 }
 160
 161 static int init_chipset_svwks(struct pci_dev *dev)
 162 {
 163         unsigned int reg;
 164         u8 btr;
 165
 166         /* force Master Latency Timer value to 64 PCICLKs */
 167         pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
 168
 169         /* OSB4 : South Bridge and IDE */
 170         if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
 171                 struct pci_dev *isa_dev =
 172                         pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 173                                         PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
 174                 if (isa_dev) {
 175                         pci_read_config_dword(isa_dev, 0x64, &reg);
 176                         reg &= ~0x00002000; /* disable 600ns interrupt mask */
 177                         if(!(reg & 0x00004000))
 178                                 printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
 179                                         "enabled.\n", pci_name(dev));
 180                         reg |=  0x00004000; /* enable UDMA/33 support */
 181                         pci_write_config_dword(isa_dev, 0x64, reg);
 182                         pci_dev_put(isa_dev);
 183                 }
 184         }
 185
 186         /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
 187         else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
 188                  (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 189                  (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
 190
 191                 /* Third Channel Test */
 192                 if (!(PCI_FUNC(dev->devfn) & 1)) {
 193                         struct pci_dev * findev = NULL;
 194                         u32 reg4c = 0;
 195                         findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 196                                 PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
 197                         if (findev) {
 198                                 pci_read_config_dword(findev, 0x4C, &reg4c);
 199                                 reg4c &= ~0x000007FF;
 200                                 reg4c |=  0x00000040;
 201                                 reg4c |=  0x00000020;
 202                                 pci_write_config_dword(findev, 0x4C, reg4c);
 203                                 pci_dev_put(findev);
 204                         }
 205                         outb_p(0x06, 0x0c00);
 206                         dev->irq = inb_p(0x0c01);
 207                 } else {
 208                         struct pci_dev * findev = NULL;
 209                         u8 reg41 = 0;
 210
 211                         findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 212                                         PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
 213                         if (findev) {
 214                                 pci_read_config_byte(findev, 0x41, &reg41);
 215                                 reg41 &= ~0x40;
 216                                 pci_write_config_byte(findev, 0x41, reg41);
 217                                 pci_dev_put(findev);
 218                         }
 219                         /*
 220                          * This is a device pin issue on CSB6.
 221                          * Since there will be a future raid mode,
 222                          * early versions of the chipset require the
 223                          * interrupt pin to be set, and it is a compatibility
 224                          * mode issue.
 225                          */
 226                         if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
 227                                 dev->irq = 0;
 228                 }
 229 //              pci_read_config_dword(dev, 0x40, &pioreg)
 230 //              pci_write_config_dword(dev, 0x40, 0x99999999);
 231 //              pci_read_config_dword(dev, 0x44, &dmareg);
 232 //              pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
 233                 /* setup the UDMA Control register
 234                  *
 235                  * 1. clear bit 6 to enable DMA
 236                  * 2. enable DMA modes with bits 0-1
 237                  *      00 : legacy
 238                  *      01 : udma2
 239                  *      10 : udma2/udma4
 240                  *      11 : udma2/udma4/udma5
 241                  */
 242                 pci_read_config_byte(dev, 0x5A, &btr);
 243                 btr &= ~0x40;
 244                 if (!(PCI_FUNC(dev->devfn) & 1))
 245                         btr |= 0x2;
 246                 else
 247                         btr |= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
 248                 pci_write_config_byte(dev, 0x5A, btr);
 249         }
 250         /* Setup HT1000 SouthBridge Controller - Single Channel Only */
 251         else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
 252                 pci_read_config_byte(dev, 0x5A, &btr);
 253                 btr &= ~0x40;
 254                 btr |= 0x3;
 255                 pci_write_config_byte(dev, 0x5A, btr);
 256         }
 257
 258         return 0;
 259 }
 260
 261 static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
 262 {
 263         return ATA_CBL_PATA80;
 264 }
 265
 266 /* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
 267  * of the subsystem device ID indicate presence of an 80-pin cable.
 268  * Bit 15 clear = secondary IDE channel does not have 80-pin cable.
 269  * Bit 15 set   = secondary IDE channel has 80-pin cable.
 270  * Bit 14 clear = primary IDE channel does not have 80-pin cable.
 271  * Bit 14 set   = primary IDE channel has 80-pin cable.
 272  */
 273 static u8 ata66_svwks_dell(ide_hwif_t *hwif)
 274 {
 275         struct pci_dev *dev = to_pci_dev(hwif->dev);
 276
 277         if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
 278             dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
 279             (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
 280              dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
 281                 return ((1 << (hwif->channel + 14)) &
 282                         dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
 283         return ATA_CBL_PATA40;
 284 }
 285
 286 /* Sun Cobalt Alpine hardware avoids the 80-pin cable
 287  * detect issue by attaching the drives directly to the board.
 288  * This check follows the Dell precedent (how scary is that?!)
 289  *
 290  * WARNING: this only works on Alpine hardware!
 291  */
 292 static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
 293 {
 294         struct pci_dev *dev = to_pci_dev(hwif->dev);
 295
 296         if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
 297             dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
 298             dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
 299                 return ((1 << (hwif->channel + 14)) &
 300                         dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
 301         return ATA_CBL_PATA40;
 302 }
 303
 304 static u8 svwks_cable_detect(ide_hwif_t *hwif)
 305 {
 306         struct pci_dev *dev = to_pci_dev(hwif->dev);
 307
 308         /* Server Works */
 309         if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
 310                 return ata66_svwks_svwks (hwif);
 311
 312         /* Dell PowerEdge */
 313         if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
 314                 return ata66_svwks_dell (hwif);
 315
 316         /* Cobalt Alpine */
 317         if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
 318                 return ata66_svwks_cobalt (hwif);
 319
 320         /* Per Specified Design by OEM, and ASIC Architect */
 321         if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 322             (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
 323                 return ATA_CBL_PATA80;
 324
 325         return ATA_CBL_PATA40;
 326 }
 327
 328 static const struct ide_port_ops osb4_port_ops = {
 329         .set_pio_mode           = svwks_set_pio_mode,
 330         .set_dma_mode           = svwks_set_dma_mode,
 331 };
 332
 333 static const struct ide_port_ops svwks_port_ops = {
 334         .set_pio_mode           = svwks_set_pio_mode,
 335         .set_dma_mode           = svwks_set_dma_mode,
 336         .udma_filter            = svwks_udma_filter,
 337         .cable_detect           = svwks_cable_detect,
 338 };
 339
 340 static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
 341         {       /* 0: OSB4 */
 342                 .name           = DRV_NAME,
 343                 .init_chipset   = init_chipset_svwks,
 344                 .port_ops       = &osb4_port_ops,
 345                 .pio_mask       = ATA_PIO4,
 346                 .mwdma_mask     = ATA_MWDMA2,
 347                 .udma_mask      = 0x00, /* UDMA is problematic on OSB4 */
 348         },
 349         {       /* 1: CSB5 */
 350                 .name           = DRV_NAME,
 351                 .init_chipset   = init_chipset_svwks,
 352                 .port_ops       = &svwks_port_ops,
 353                 .pio_mask       = ATA_PIO4,
 354                 .mwdma_mask     = ATA_MWDMA2,
 355                 .udma_mask      = ATA_UDMA5,
 356         },
 357         {       /* 2: CSB6 */
 358                 .name           = DRV_NAME,
 359                 .init_chipset   = init_chipset_svwks,
 360                 .port_ops       = &svwks_port_ops,
 361                 .pio_mask       = ATA_PIO4,
 362                 .mwdma_mask     = ATA_MWDMA2,
 363                 .udma_mask      = ATA_UDMA5,
 364         },
 365         {       /* 3: CSB6-2 */
 366                 .name           = DRV_NAME,
 367                 .init_chipset   = init_chipset_svwks,
 368                 .port_ops       = &svwks_port_ops,
 369                 .host_flags     = IDE_HFLAG_SINGLE,
 370                 .pio_mask       = ATA_PIO4,
 371                 .mwdma_mask     = ATA_MWDMA2,
 372                 .udma_mask      = ATA_UDMA5,
 373         },
 374         {       /* 4: HT1000 */
 375                 .name           = DRV_NAME,
 376                 .init_chipset   = init_chipset_svwks,
 377                 .port_ops       = &svwks_port_ops,
 378                 .host_flags     = IDE_HFLAG_SINGLE,
 379                 .pio_mask       = ATA_PIO4,
 380                 .mwdma_mask     = ATA_MWDMA2,
 381                 .udma_mask      = ATA_UDMA5,
 382         }
 383 };
 384
 385 /**
 386  *      svwks_init_one  -       called when a OSB/CSB is found
 387  *      @dev: the svwks device
 388  *      @id: the matching pci id
 389  *
 390  *      Called when the PCI registration layer (or the IDE initialization)
 391  *      finds a device matching our IDE device tables.
 392  */
 393
 394 static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 395 {
 396         struct ide_port_info d;
 397         u8 idx = id->driver_data;
 398
 399         d = serverworks_chipsets[idx];
 400
 401         if (idx == 1)
 402                 d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
 403         else if (idx == 2 || idx == 3) {
 404                 if ((PCI_FUNC(dev->devfn) & 1) == 0) {
 405                         if (pci_resource_start(dev, 0) != 0x01f1)
 406                                 d.host_flags |= IDE_HFLAG_NON_BOOTABLE;
 407                         d.host_flags |= IDE_HFLAG_SINGLE;
 408                 } else
 409                         d.host_flags &= ~IDE_HFLAG_SINGLE;
 410         }
 411
 412         return ide_pci_init_one(dev, &d, NULL);
 413 }
 414
 415 static const struct pci_device_id svwks_pci_tbl[] = {
 416         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE),   0 },
 417         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE),   1 },
 418         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE),   2 },
 419         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2),  3 },
 420         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
 421         { 0, },
 422 };
 423 MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
 424
 425 static struct pci_driver svwks_pci_driver = {
 426         .name           = "Serverworks_IDE",
 427         .id_table       = svwks_pci_tbl,
 428         .probe          = svwks_init_one,
 429         .remove         = ide_pci_remove,
 430         .suspend        = ide_pci_suspend,
 431         .resume         = ide_pci_resume,
 432 };
 433
 434 static int __init svwks_ide_init(void)
 435 {
 436         return ide_pci_register_driver(&svwks_pci_driver);
 437 }
 438
 439 static void __exit svwks_ide_exit(void)
 440 {
 441         pci_unregister_driver(&svwks_pci_driver);
 442 }
 443
 444 module_init(svwks_ide_init);
 445 module_exit(svwks_ide_exit);
 446
 447 MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick, Bartlomiej Zolnierkiewicz");
 448 MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
 449 MODULE_LICENSE("GPL");