include/configs/ten64.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2017 NXP
   4  * Copyright 2019-2021 Traverse Technologies
   5  */
   6
   7 #ifndef __TEN64_H
   8 #define __TEN64_H
   9
  10 #include "ls1088a_common.h"
  11
  12 #define CFG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
  13
  14 #define QSPI_NOR_BOOTCOMMAND    "run distro_bootcmd"
  15 #define SD_BOOTCOMMAND          "run distro_bootcmd"
  16
  17 #define SD_FIRMWARE_PATH "firmware/traverse/ten64/"
  18
  19 #define QSPI_MC_INIT_CMD                                \
  20         "sf probe 0:0 && sf read 0x80000000 0x300000 0x200000 &&"       \
  21         "sf read 0x80200000 0x5C0000 0x40000 &&"                                \
  22         "fsl_mc start mc 0x80000000 0x80200000 && " \
  23         "sf read 0x8E000000 0x580000 0x40000 && fsl_mc lazyapply DPL 0x8E000000 && "\
  24         "echo 'default DPL loaded'\0"
  25 #define SD_MC_INIT_CMD                          \
  26         "mmcinfo; fatload mmc 0 0x80000000 " SD_FIRMWARE_PATH "mc_ls1088a.itb; "\
  27         "fatload mmc 0 0x80200000 " SD_FIRMWARE_PATH "dpc.0x1D-0x0D.dtb; "\
  28         "fsl_mc start mc 0x80000000 0x80200000 && "     \
  29         "fatload mmc 0 0x8E000000 " SD_FIRMWARE_PATH "eth-dpl-all.dtb && " \
  30         "fsl_mc lazyapply DPL 0x8E000000 && echo 'default DPL loaded'\0"
  31
  32 #define BOOT_TARGET_DEVICES(func) \
  33         func(NVME, nvme, 0) \
  34         func(USB, usb, 0) \
  35         func(MMC, mmc, 0) \
  36         func(SCSI, scsi, 0) \
  37         func(DHCP, dhcp, 0) \
  38         func(PXE, pxe, 0)
  39 #include <config_distro_bootcmd.h>
  40
  41 #define OPENWRT_NAND_BOOTCMD    \
  42         "bootcmd_openwrt_nand=ubi part ubi${openwrt_active_sys} && "\
  43         "ubi read $load_addr kernel && " \
  44         "setenv bootargs \"root=/dev/ubiblock0_1 earlycon ubi.mtd=ubi${openwrt_active_sys}\" &&"\
  45         "bootm $load_addr#ten64\0"
  46 #undef CFG_EXTRA_ENV_SETTINGS
  47
  48 #if CONFIG_IS_ENABLED(CMD_BOOTMENU)
  49 #define DEFAULT_MENU_ENTRIES \
  50         "bootmenu_0=Continue standard boot=run bootcmd\0" \
  51         "bootmenu_1=Boot into recovery=run bootcmd_recovery\0" \
  52         "bootmenu_2=Boot OpenWrt from NAND=run bootcmd_openwrt_nand\0"
  53 #else
  54 #define DEFAULT_MENU_ENTRIES ""
  55 #endif /* CONFIG_IS_ENABLED(CMD_BOOTMENU) */
  56
  57 #define CFG_EXTRA_ENV_SETTINGS \
  58         "BOARD=ten64\0"                                 \
  59         "fdt_addr_r=0x90000000\0"               \
  60         "fdt_high=0xa0000000\0"                 \
  61         "kernel_addr_r=0x81000000\0"            \
  62         "load_addr=0xa0000000\0"                \
  63         BOOTENV \
  64         OPENWRT_NAND_BOOTCMD \
  65         "openwrt_active_sys=a\0" \
  66         "load_efi_dtb=mtd read devicetree $fdt_addr_r && fdt addr $fdt_addr_r && " \
  67         "fdt resize && fdt boardsetup\0" \
  68         "bootcmd_recovery=mtd read recovery 0xa0000000;  " \
  69         "setenv bootargs \"earlycon root=/dev/ram0 ramdisk_size=0x3000000\" && bootm 0xa0000000#ten64\0" \
  70         DEFAULT_MENU_ENTRIES
  71
  72 #endif /* __TEN64_H */