| blob | 7bc92a9b9165ebca5245a9df3b63ff3ea1e0ea09 |
1 #
2 # CDDL HEADER START
3 #
4 # The contents of this file are subject to the terms of the
5 # Common Development and Distribution License (the "License").
6 # You may not use this file except in compliance with the License.
7 #
8 # You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
9 # or http://www.opensolaris.org/os/licensing.
10 # See the License for the specific language governing permissions
11 # and limitations under the License.
12 #
13 # When distributing Covered Code, include this CDDL HEADER in each
14 # file and include the License file at usr/src/OPENSOLARIS.LICENSE.
15 # If applicable, add the following below this CDDL HEADER, with the
16 # fields enclosed by brackets "[]" replaced with your own identifying
17 # information: Portions Copyright [yyyy] [name of copyright owner]
18 #
19 # CDDL HEADER END
20 #
21 # Copyright 2008 Sun Microsystems, Inc. All rights reserved.
22 # Use is subject to license terms.
23 #
26 #
27 # scsa2usb.conf file
28 #
29 # WARNING: This is an UNSTABLE configuration file. Its contents
30 # may change at any time.
31 #
32 # Records in this file may be used to override the vendor-supplied subclass
33 # and protocol values for USB mass storage devices. Note: only non-class-
34 # compliant values for subclass and protocol (e.g. 0xff) will be overridden.
35 # If a device supplies legal, class-compliant values for these fields, those
36 # values will not be overridden.
37 #
38 # Records in this file may also be used to override the default power
39 # management behavior of USB mass storage devices.
40 #
41 # A record in this file has the following format:-
42 # "vid=vId pid=pId rev=revision subclass=override protocol=override pm=pmvalue
43 # removable=remvalue modesense=modesensevalue"
44 #
45 # where:
46 # vId/pId/revision: are obtained from
47 # 'prtconf -v' output for the device
48 #
49 # vendorId is the hardware property 'usb-vendor-id'
50 # productId is the hardware property 'usb-product-id'
51 # revision is the hardware property 'usb-revision-id'
52 #
53 # subclass override - could be either "ufi", "scsi", or "atapi"
54 # where "ufi" -> Device follows UFI transport
55 # "atapi" -> Device follows ATAPI transport
56 # "scsi" -> Device follows SCSI transport
57 #
58 # These values are part of USB Interface descriptor for that device.
59 # bInterfaceSubClass type
60 # 0x1 "scsi"
61 # 0x2 "atapi"
62 # 0x4 "ufi"
63 # 0x5 "atapi"
64 # 0x6 "scsi"
65 #
66 # protocol override - could be either "cbi", "cb", or "bo"
67 # where "cbi" -> Control/Bulk/Interrupt device
68 # "cb" -> Control/Bulk/Interrupt device with no
69 # interrupt pipe status
70 # "bo" -> Bulk Only device
71 #
72 # These values are part of USB Interface descriptor for that device.
73 # bInterfaceProtocol type
74 # 0x0 "cbi"
75 # 0x1 "cb"
76 # 0x2 "bo" - zip protocol
77 # 0x50 "bo"
78 #
79 # pmvalue - "off" if device is not to be power managed.
80 # This is the only legal value for this parameter.
81 # This parameter is included because some devices
82 # are not capable of being power-managed, i.e. they
83 # will not respond after having their power lowered.
84 # If this is the case, the device should have power
85 # management disabled by setting this to "off".
86 #
87 # remvalue - "true" if the device's removable media information
88 # in its hardware inquiry data is to be overridden. This
89 # is the only legal value for this parameter.
90 #
91 # NOTE: In previous releases, the removable media information
92 # was always overridden and the only legal value was "false".
93 #
94 # There is a removable media status bit in the USB storage
95 # device's inquiry data to indicate if the device has a media
96 # that can be removed. Usually only devices like floppy drives
97 # or CD/DVD drives that really have a removable media can
98 # have this bit set and be called removable media devices.
99 # Solaris treats removable media devices and non-removable
100 # media devices differently. Refer to "System Administration
101 # Guide: Devices and File Systems" - "Using USB Devices
102 # (Tasks)" - "Using USB Mass Storage Devices" section for
103 # the differences in system behavior of treating removable
104 # media devices and non-removable media devices.
105 #
106 # By default, Solaris will treat USB storage devices as
107 # removable media devices depending on the removable media
108 # bit value. In some cases this may be undesirable and the
109 # behavior of the previous releases should be preserved. In
110 # this case the removable media bit value should be overridden.
111 # By setting "remvalue" to "true", the information provided
112 # by the device is ignored. Consequently a USB hard disk
113 # is treated as a removable media disk and will not show in
114 # format(8) disk list.
115 #
116 # modesensevalue - "false" if the device cannot handle mode sense
117 # requests. This is the only legal value for this
118 # parameter. Some devices choke on mode sense requests
119 # and become unusable.
120 #
121 # reduced-cmd-support - "true" if the device cannot handle
122 # mode sense, or start/stop, or doorlock, or doesn not
123 # report correct residues on data transfers.
124 # This is the only legal value for this parameter. This
125 # setting is recommended for USB memory sticks and USB2.0
126 # enclosures which may not be USB Mass Storage spec
127 # compliant.
128 #
129 # NOTE: As a special case, "*" may be used as a wildcard which matches
130 # any field. This is useful in situations where more than one
131 # vendor produces a particular model of a product, one vendor
132 # produces more than one product with the same characteristics,
133 # or a product has more than one revision. The subclass and
134 # protocol override values may also contain "*" if one or the
135 # the other does not require an override value.
136 #
137 # For the properties to take effect, reboot the system.
138 #
139 # To create this list, first COPY the "attribute-override-list =" line
140 # to the end of the file and uncomment it.
141 #
142 # Then COPY sample records and uncomment them or create new records.
143 # The list consists of one or more records separated by commas and
144 # terminated by a semicolon.
145 #
146 # IMPORTANT: CREATE THE LIST BY ENTERING NEW RECORDS AFTER THE LAST LINE
147 # OF THE FILE. TO PREVENT CHANGES BEING LOST WHEN THIS FILE IS UPGRADED,
148 # DO NOT UNCOMMENT LINES "IN PLACE."
149 #
150 #attribute-override-list =
151 #
152 # for Sony DSC-S85 USB Digital camera:
153 # "vid=0x54c pid=0x10 rev=* subclass=ufi protocol=cb",
154 #
155 # for SanDisk SDDR-05a CF:
156 # "vid=0x781 pid=1 rev=* subclass=ufi protocol=cb";
157 #
158 # to apply to all USB Mass Storage devices:
159 # "vid=* reduced-cmd-support=true";
160 #
161 # (this is not recommended for CD and DVD reader/writers but may work
162 # well with USB memory sticks)
163 #
164 # ANYTHING CHANGED BEFORE THIS POINT MAY BE OVERWRITTEN IN UPGRADE