b43: Changes to enable BCM4311 rev 02 with wireless core revision 13
[wrt350n-kernel.git] / drivers / net / 7990.h
blob0a5837b9642194799bedaf26abf3721bafb94579
1 /*
2 * 7990.h -- LANCE ethernet IC generic routines.
3 * This is an attempt to separate out the bits of various ethernet
4 * drivers that are common because they all use the AMD 7990 LANCE
5 * (Local Area Network Controller for Ethernet) chip.
7 * Copyright (C) 05/1998 Peter Maydell <pmaydell@chiark.greenend.org.uk>
9 * Most of this stuff was obtained by looking at other LANCE drivers,
10 * in particular a2065.[ch]. The AMD C-LANCE datasheet was also helpful.
13 #ifndef _7990_H
14 #define _7990_H
16 /* The lance only has two register locations. We communicate mostly via memory. */
17 #define LANCE_RDP 0 /* Register Data Port */
18 #define LANCE_RAP 2 /* Register Address Port */
20 /* Transmit/receive ring definitions.
21 * We allow the specific drivers to override these defaults if they want to.
22 * NB: according to lance.c, increasing the number of buffers is a waste
23 * of space and reduces the chance that an upper layer will be able to
24 * reorder queued Tx packets based on priority. [Clearly there is a minimum
25 * limit too: too small and we drop rx packets and can't tx at full speed.]
26 * 4+4 seems to be the usual setting; the atarilance driver uses 3 and 5.
29 /* Blast! This won't work. The problem is that we can't specify a default
30 * setting because that would cause the lance_init_block struct to be
31 * too long (and overflow the RAM on shared-memory cards like the HP LANCE.
33 #ifndef LANCE_LOG_TX_BUFFERS
34 #define LANCE_LOG_TX_BUFFERS 1
35 #define LANCE_LOG_RX_BUFFERS 3
36 #endif
38 #define TX_RING_SIZE (1<<LANCE_LOG_TX_BUFFERS)
39 #define RX_RING_SIZE (1<<LANCE_LOG_RX_BUFFERS)
40 #define TX_RING_MOD_MASK (TX_RING_SIZE - 1)
41 #define RX_RING_MOD_MASK (RX_RING_SIZE - 1)
42 #define TX_RING_LEN_BITS ((LANCE_LOG_TX_BUFFERS) << 29)
43 #define RX_RING_LEN_BITS ((LANCE_LOG_RX_BUFFERS) << 29)
44 #define PKT_BUFF_SIZE (1544)
45 #define RX_BUFF_SIZE PKT_BUFF_SIZE
46 #define TX_BUFF_SIZE PKT_BUFF_SIZE
48 /* Each receive buffer is described by a receive message descriptor (RMD) */
49 struct lance_rx_desc {
50 volatile unsigned short rmd0; /* low address of packet */
51 volatile unsigned char rmd1_bits; /* descriptor bits */
52 volatile unsigned char rmd1_hadr; /* high address of packet */
53 volatile short length; /* This length is 2s complement (negative)!
54 * Buffer length
56 volatile unsigned short mblength; /* Actual number of bytes received */
59 /* Ditto for TMD: */
60 struct lance_tx_desc {
61 volatile unsigned short tmd0; /* low address of packet */
62 volatile unsigned char tmd1_bits; /* descriptor bits */
63 volatile unsigned char tmd1_hadr; /* high address of packet */
64 volatile short length; /* Length is 2s complement (negative)! */
65 volatile unsigned short misc;
68 /* There are three memory structures accessed by the LANCE:
69 * the initialization block, the receive and transmit descriptor rings,
70 * and the data buffers themselves. In fact we might as well put the
71 * init block,the Tx and Rx rings and the buffers together in memory:
73 struct lance_init_block {
74 volatile unsigned short mode; /* Pre-set mode (reg. 15) */
75 volatile unsigned char phys_addr[6]; /* Physical ethernet address */
76 volatile unsigned filter[2]; /* Multicast filter (64 bits) */
78 /* Receive and transmit ring base, along with extra bits. */
79 volatile unsigned short rx_ptr; /* receive descriptor addr */
80 volatile unsigned short rx_len; /* receive len and high addr */
81 volatile unsigned short tx_ptr; /* transmit descriptor addr */
82 volatile unsigned short tx_len; /* transmit len and high addr */
84 /* The Tx and Rx ring entries must be aligned on 8-byte boundaries.
85 * This will be true if this whole struct is 8-byte aligned.
87 volatile struct lance_tx_desc btx_ring[TX_RING_SIZE];
88 volatile struct lance_rx_desc brx_ring[RX_RING_SIZE];
90 volatile char tx_buf [TX_RING_SIZE][TX_BUFF_SIZE];
91 volatile char rx_buf [RX_RING_SIZE][RX_BUFF_SIZE];
92 /* we use this just to make the struct big enough that we can move its startaddr
93 * in order to force alignment to an eight byte boundary.
97 /* This is where we keep all the stuff the driver needs to know about.
98 * I'm definitely unhappy about the mechanism for allowing specific
99 * drivers to add things...
101 struct lance_private
103 char *name;
104 unsigned long base;
105 volatile struct lance_init_block *init_block; /* CPU address of RAM */
106 volatile struct lance_init_block *lance_init_block; /* LANCE address of RAM */
108 int rx_new, tx_new;
109 int rx_old, tx_old;
111 int lance_log_rx_bufs, lance_log_tx_bufs;
112 int rx_ring_mod_mask, tx_ring_mod_mask;
114 int tpe; /* TPE is selected */
115 int auto_select; /* cable-selection is by carrier */
116 unsigned short busmaster_regval;
118 unsigned int irq; /* IRQ to register */
120 /* This is because the HP LANCE is disgusting and you have to check
121 * a DIO-specific register every time you read/write the LANCE regs :-<
122 * [could we get away with making these some sort of macro?]
124 void (*writerap)(void *, unsigned short);
125 void (*writerdp)(void *, unsigned short);
126 unsigned short (*readrdp)(void *);
127 spinlock_t devlock;
128 char tx_full;
132 * Am7990 Control and Status Registers
134 #define LE_CSR0 0x0000 /* LANCE Controller Status */
135 #define LE_CSR1 0x0001 /* IADR[15:0] (bit0==0 ie word aligned) */
136 #define LE_CSR2 0x0002 /* IADR[23:16] (high bits reserved) */
137 #define LE_CSR3 0x0003 /* Misc */
140 * Bit definitions for CSR0 (LANCE Controller Status)
142 #define LE_C0_ERR 0x8000 /* Error = BABL | CERR | MISS | MERR */
143 #define LE_C0_BABL 0x4000 /* Babble: Transmitted too many bits */
144 #define LE_C0_CERR 0x2000 /* No Heartbeat (10BASE-T) */
145 #define LE_C0_MISS 0x1000 /* Missed Frame (no rx buffer to put it in) */
146 #define LE_C0_MERR 0x0800 /* Memory Error */
147 #define LE_C0_RINT 0x0400 /* Receive Interrupt */
148 #define LE_C0_TINT 0x0200 /* Transmit Interrupt */
149 #define LE_C0_IDON 0x0100 /* Initialization Done */
150 #define LE_C0_INTR 0x0080 /* Interrupt Flag
151 = BABL | MISS | MERR | RINT | TINT | IDON */
152 #define LE_C0_INEA 0x0040 /* Interrupt Enable */
153 #define LE_C0_RXON 0x0020 /* Receive On */
154 #define LE_C0_TXON 0x0010 /* Transmit On */
155 #define LE_C0_TDMD 0x0008 /* Transmit Demand */
156 #define LE_C0_STOP 0x0004 /* Stop */
157 #define LE_C0_STRT 0x0002 /* Start */
158 #define LE_C0_INIT 0x0001 /* Initialize */
162 * Bit definitions for CSR3
164 #define LE_C3_BSWP 0x0004 /* Byte Swap
165 (on for big endian byte order) */
166 #define LE_C3_ACON 0x0002 /* ALE Control
167 (on for active low ALE) */
168 #define LE_C3_BCON 0x0001 /* Byte Control */
172 * Mode Flags
174 #define LE_MO_PROM 0x8000 /* Promiscuous Mode */
175 /* these next ones 0x4000 -- 0x0080 are not available on the LANCE 7990,
176 * but they are in NetBSD's am7990.h, presumably for backwards-compatible chips
178 #define LE_MO_DRCVBC 0x4000 /* disable receive broadcast */
179 #define LE_MO_DRCVPA 0x2000 /* disable physical address detection */
180 #define LE_MO_DLNKTST 0x1000 /* disable link status */
181 #define LE_MO_DAPC 0x0800 /* disable automatic polarity correction */
182 #define LE_MO_MENDECL 0x0400 /* MENDEC loopback mode */
183 #define LE_MO_LRTTSEL 0x0200 /* lower RX threshold / TX mode selection */
184 #define LE_MO_PSEL1 0x0100 /* port selection bit1 */
185 #define LE_MO_PSEL0 0x0080 /* port selection bit0 */
186 /* and this one is from the C-LANCE data sheet... */
187 #define LE_MO_EMBA 0x0080 /* Enable Modified Backoff Algorithm
188 (C-LANCE, not original LANCE) */
189 #define LE_MO_INTL 0x0040 /* Internal Loopback */
190 #define LE_MO_DRTY 0x0020 /* Disable Retry */
191 #define LE_MO_FCOLL 0x0010 /* Force Collision */
192 #define LE_MO_DXMTFCS 0x0008 /* Disable Transmit CRC */
193 #define LE_MO_LOOP 0x0004 /* Loopback Enable */
194 #define LE_MO_DTX 0x0002 /* Disable Transmitter */
195 #define LE_MO_DRX 0x0001 /* Disable Receiver */
199 * Receive Flags
201 #define LE_R1_OWN 0x80 /* LANCE owns the descriptor */
202 #define LE_R1_ERR 0x40 /* Error */
203 #define LE_R1_FRA 0x20 /* Framing Error */
204 #define LE_R1_OFL 0x10 /* Overflow Error */
205 #define LE_R1_CRC 0x08 /* CRC Error */
206 #define LE_R1_BUF 0x04 /* Buffer Error */
207 #define LE_R1_SOP 0x02 /* Start of Packet */
208 #define LE_R1_EOP 0x01 /* End of Packet */
209 #define LE_R1_POK 0x03 /* Packet is complete: SOP + EOP */
213 * Transmit Flags
215 #define LE_T1_OWN 0x80 /* LANCE owns the descriptor */
216 #define LE_T1_ERR 0x40 /* Error */
217 #define LE_T1_RES 0x20 /* Reserved, LANCE writes this with a zero */
218 #define LE_T1_EMORE 0x10 /* More than one retry needed */
219 #define LE_T1_EONE 0x08 /* One retry needed */
220 #define LE_T1_EDEF 0x04 /* Deferred */
221 #define LE_T1_SOP 0x02 /* Start of Packet */
222 #define LE_T1_EOP 0x01 /* End of Packet */
223 #define LE_T1_POK 0x03 /* Packet is complete: SOP + EOP */
226 * Error Flags
228 #define LE_T3_BUF 0x8000 /* Buffer Error */
229 #define LE_T3_UFL 0x4000 /* Underflow Error */
230 #define LE_T3_LCOL 0x1000 /* Late Collision */
231 #define LE_T3_CLOS 0x0800 /* Loss of Carrier */
232 #define LE_T3_RTY 0x0400 /* Retry Error */
233 #define LE_T3_TDR 0x03ff /* Time Domain Reflectometry */
235 /* Miscellaneous useful macros */
237 #define TX_BUFFS_AVAIL ((lp->tx_old<=lp->tx_new)?\
238 lp->tx_old+lp->tx_ring_mod_mask-lp->tx_new:\
239 lp->tx_old - lp->tx_new-1)
241 /* The LANCE only uses 24 bit addresses. This does the obvious thing. */
242 #define LANCE_ADDR(x) ((int)(x) & ~0xff000000)
244 /* Now the prototypes we export */
245 extern int lance_open(struct net_device *dev);
246 extern int lance_close (struct net_device *dev);
247 extern int lance_start_xmit (struct sk_buff *skb, struct net_device *dev);
248 extern void lance_set_multicast (struct net_device *dev);
249 extern void lance_tx_timeout(struct net_device *dev);
250 #ifdef CONFIG_NET_POLL_CONTROLLER
251 extern void lance_poll(struct net_device *dev);
252 #endif
254 #endif /* ndef _7990_H */