include/asm-mips/sgi/mc.h

   1 /*
   2  * This file is subject to the terms and conditions of the GNU General Public
   3  * License. See the file "COPYING" in the main directory of this archive
   4  * for more details.
   5  *
   6  * mc.h: Definitions for SGI Memory Controller
   7  *
   8  * Copyright (C) 1996 David S. Miller
   9  * Copyright (C) 1999 Ralf Baechle
  10  * Copyright (C) 1999 Silicon Graphics, Inc.
  11  */
  12
  13 #ifndef _SGI_MC_H
  14 #define _SGI_MC_H
  15
  16 struct sgimc_regs {
  17         u32 _unused0;
  18         volatile u32 cpuctrl0;  /* CPU control register 0, readwrite */
  19 #define SGIMC_CCTRL0_REFS       0x0000000f /* REFS mask */
  20 #define SGIMC_CCTRL0_EREFRESH   0x00000010 /* Memory refresh enable */
  21 #define SGIMC_CCTRL0_EPERRGIO   0x00000020 /* GIO parity error enable */
  22 #define SGIMC_CCTRL0_EPERRMEM   0x00000040 /* Main mem parity error enable */
  23 #define SGIMC_CCTRL0_EPERRCPU   0x00000080 /* CPU bus parity error enable */
  24 #define SGIMC_CCTRL0_WDOG       0x00000100 /* Watchdog timer enable */
  25 #define SGIMC_CCTRL0_SYSINIT    0x00000200 /* System init bit */
  26 #define SGIMC_CCTRL0_GFXRESET   0x00000400 /* Graphics interface reset */
  27 #define SGIMC_CCTRL0_EISALOCK   0x00000800 /* Lock CPU from memory for EISA */
  28 #define SGIMC_CCTRL0_EPERRSCMD  0x00001000 /* SysCMD bus parity error enable */
  29 #define SGIMC_CCTRL0_IENAB      0x00002000 /* Allow interrupts from MC */
  30 #define SGIMC_CCTRL0_ESNOOP     0x00004000 /* Snooping I/O enable */
  31 #define SGIMC_CCTRL0_EPROMWR    0x00008000 /* Prom writes from cpu enable */
  32 #define SGIMC_CCTRL0_WRESETPMEM 0x00010000 /* Perform warm reset, preserves mem */
  33 #define SGIMC_CCTRL0_LENDIAN    0x00020000 /* Put MC in little-endian mode */
  34 #define SGIMC_CCTRL0_WRESETDMEM 0x00040000 /* Warm reset, destroys mem contents */
  35 #define SGIMC_CCTRL0_CMEMBADPAR 0x02000000 /* Generate bad perr from cpu to mem */
  36 #define SGIMC_CCTRL0_R4KNOCHKPARR 0x04000000 /* Don't chk parity on mem data reads */
  37 #define SGIMC_CCTRL0_GIOBTOB    0x08000000 /* Allow GIO back to back writes */
  38         u32 _unused1;
  39         volatile u32 cpuctrl1;  /* CPU control register 1, readwrite */
  40 #define SGIMC_CCTRL1_EGIOTIMEO  0x00000010 /* GIO bus timeout enable */
  41 #define SGIMC_CCTRL1_FIXEDEHPC  0x00001000 /* Fixed HPC endianness */
  42 #define SGIMC_CCTRL1_LITTLEHPC  0x00002000 /* Little endian HPC */
  43 #define SGIMC_CCTRL1_FIXEDEEXP0 0x00004000 /* Fixed EXP0 endianness */
  44 #define SGIMC_CCTRL1_LITTLEEXP0 0x00008000 /* Little endian EXP0 */
  45 #define SGIMC_CCTRL1_FIXEDEEXP1 0x00010000 /* Fixed EXP1 endianness */
  46 #define SGIMC_CCTRL1_LITTLEEXP1 0x00020000 /* Little endian EXP1 */
  47
  48         u32 _unused2;
  49         volatile u32 watchdogt; /* Watchdog reg rdonly, write clears */
  50
  51         u32 _unused3;
  52         volatile u32 systemid;  /* MC system ID register, readonly */
  53 #define SGIMC_SYSID_MASKREV     0x0000000f /* Revision of MC controller */
  54 #define SGIMC_SYSID_EPRESENT    0x00000010 /* Indicates presence of EISA bus */
  55
  56         u32 _unused4[3];
  57         volatile u32 divider;   /* Divider reg for RPSS */
  58
  59         u32 _unused5;
  60         u32 eeprom;             /* EEPROM byte reg for r4k */
  61 #define SGIMC_EEPROM_PRE        0x00000001 /* eeprom chip PRE pin assertion */
  62 #define SGIMC_EEPROM_CSEL       0x00000002 /* Active high, eeprom chip select */
  63 #define SGIMC_EEPROM_SECLOCK    0x00000004 /* EEPROM serial clock */
  64 #define SGIMC_EEPROM_SDATAO     0x00000008 /* Serial EEPROM data-out */
  65 #define SGIMC_EEPROM_SDATAI     0x00000010 /* Serial EEPROM data-in */
  66
  67         u32 _unused6[3];
  68         volatile u32 rcntpre;   /* Preload refresh counter */
  69
  70         u32 _unused7;
  71         volatile u32 rcounter;  /* Readonly refresh counter */
  72
  73         u32 _unused8[13];
  74         volatile u32 giopar;    /* Parameter word for GIO64 */
  75 #define SGIMC_GIOPAR_HPC64      0x00000001 /* HPC talks to GIO using 64-bits */
  76 #define SGIMC_GIOPAR_GFX64      0x00000002 /* GFX talks to GIO using 64-bits */
  77 #define SGIMC_GIOPAR_EXP064     0x00000004 /* EXP(slot0) talks using 64-bits */
  78 #define SGIMC_GIOPAR_EXP164     0x00000008 /* EXP(slot1) talks using 64-bits */
  79 #define SGIMC_GIOPAR_EISA64     0x00000010 /* EISA bus talks 64-bits to GIO */
  80 #define SGIMC_GIOPAR_HPC264     0x00000020 /* 2nd HPX talks 64-bits to GIO */
  81 #define SGIMC_GIOPAR_RTIMEGFX   0x00000040 /* GFX device has realtime attr */
  82 #define SGIMC_GIOPAR_RTIMEEXP0  0x00000080 /* EXP(slot0) has realtime attr */
  83 #define SGIMC_GIOPAR_RTIMEEXP1  0x00000100 /* EXP(slot1) has realtime attr */
  84 #define SGIMC_GIOPAR_MASTEREISA 0x00000200 /* EISA bus can act as bus master */
  85 #define SGIMC_GIOPAR_ONEBUS     0x00000400 /* Exists one GIO64 pipelined bus */
  86 #define SGIMC_GIOPAR_MASTERGFX  0x00000800 /* GFX can act as a bus master */
  87 #define SGIMC_GIOPAR_MASTEREXP0 0x00001000 /* EXP(slot0) can bus master */
  88 #define SGIMC_GIOPAR_MASTEREXP1 0x00002000 /* EXP(slot1) can bus master */
  89 #define SGIMC_GIOPAR_PLINEEXP0  0x00004000 /* EXP(slot0) has pipeline attr */
  90 #define SGIMC_GIOPAR_PLINEEXP1  0x00008000 /* EXP(slot1) has pipeline attr */
  91
  92         u32 _unused9;
  93         volatile u32 cputp;     /* CPU bus arb time period */
  94
  95         u32 _unused10[3];
  96         volatile u32 lbursttp;  /* Time period for long bursts */
  97
  98         /* MC chip can drive up to 4 bank 4 SIMMs each. All SIMMs in bank must
  99          * be the same size. The size encoding for supported SIMMs is bellow */
 100         u32 _unused11[9];
 101         volatile u32 mconfig0;  /* Memory config register zero */
 102         u32 _unused12;
 103         volatile u32 mconfig1;  /* Memory config register one */
 104 #define SGIMC_MCONFIG_BASEADDR  0x000000ff /* Base address of bank*/
 105 #define SGIMC_MCONFIG_RMASK     0x00001f00 /* Ram config bitmask */
 106 #define SGIMC_MCONFIG_BVALID    0x00002000 /* Bank is valid */
 107 #define SGIMC_MCONFIG_SBANKS    0x00004000 /* Number of subbanks */
 108
 109         u32 _unused13;
 110         volatile u32 cmacc;        /* Mem access config for CPU */
 111         u32 _unused14;
 112         volatile u32 gmacc;        /* Mem access config for GIO */
 113
 114         /* This define applies to both cmacc and gmacc registers above. */
 115 #define SGIMC_MACC_ALIASBIG     0x20000000 /* 512MB home for alias */
 116
 117         /* Error address/status regs from GIO and CPU perspectives. */
 118         u32 _unused15;
 119         volatile u32 cerr;      /* Error address reg for CPU */
 120         u32 _unused16;
 121         volatile u32 cstat;     /* Status reg for CPU */
 122 #define SGIMC_CSTAT_RD          0x00000100 /* read parity error */
 123 #define SGIMC_CSTAT_PAR         0x00000200 /* CPU parity error */
 124 #define SGIMC_CSTAT_ADDR        0x00000400 /* memory bus error bad addr */
 125 #define SGIMC_CSTAT_SYSAD_PAR   0x00000800 /* sysad parity error */
 126 #define SGIMC_CSTAT_SYSCMD_PAR  0x00001000 /* syscmd parity error */
 127 #define SGIMC_CSTAT_BAD_DATA    0x00002000 /* bad data identifier */
 128 #define SGIMC_CSTAT_PAR_MASK    0x00001f00 /* parity error mask */
 129 #define SGIMC_CSTAT_RD_PAR      (SGIMC_CSTAT_RD | SGIMC_CSTAT_PAR)
 130
 131         u32 _unused17;
 132         volatile u32 gerr;      /* Error address reg for GIO */
 133         u32 _unused18;
 134         volatile u32 gstat;     /* Status reg for GIO */
 135 #define SGIMC_GSTAT_RD          0x00000100 /* read parity error */
 136 #define SGIMC_GSTAT_WR          0x00000200 /* write parity error */
 137 #define SGIMC_GSTAT_TIME        0x00000400 /* GIO bus timed out */
 138 #define SGIMC_GSTAT_PROM        0x00000800 /* write to PROM when PROM_EN not set */
 139 #define SGIMC_GSTAT_ADDR        0x00001000 /* parity error on addr cycle */
 140 #define SGIMC_GSTAT_BC          0x00002000 /* parity error on byte count cycle */
 141 #define SGIMC_GSTAT_PIO_RD      0x00004000 /* read data parity on pio */
 142 #define SGIMC_GSTAT_PIO_WR      0x00008000 /* write data parity on pio */
 143
 144         /* Special hard bus locking registers. */
 145         u32 _unused19;
 146         volatile u32 syssembit;         /* Uni-bit system semaphore */
 147         u32 _unused20;
 148         volatile u32 mlock;             /* Global GIO memory access lock */
 149         u32 _unused21;
 150         volatile u32 elock;             /* Locks EISA from GIO accesses */
 151
 152         /* GIO dma control registers. */
 153         u32 _unused22[15];
 154         volatile u32 gio_dma_trans;     /* DMA mask to translation GIO addrs */
 155         u32 _unused23;
 156         volatile u32 gio_dma_sbits;     /* DMA GIO addr substitution bits */
 157         u32 _unused24;
 158         volatile u32 dma_intr_cause;    /* DMA IRQ cause indicator bits */
 159         u32 _unused25;
 160         volatile u32 dma_ctrl;          /* Main DMA control reg */
 161
 162         /* DMA TLB entry 0 */
 163         u32 _unused26[5];
 164         volatile u32 dtlb_hi0;
 165         u32 _unused27;
 166         volatile u32 dtlb_lo0;
 167
 168         /* DMA TLB entry 1 */
 169         u32 _unused28;
 170         volatile u32 dtlb_hi1;
 171         u32 _unused29;
 172         volatile u32 dtlb_lo1;
 173
 174         /* DMA TLB entry 2 */
 175         u32 _unused30;
 176         volatile u32 dtlb_hi2;
 177         u32 _unused31;
 178         volatile u32 dtlb_lo2;
 179
 180         /* DMA TLB entry 3 */
 181         u32 _unused32;
 182         volatile u32 dtlb_hi3;
 183         u32 _unused33;
 184         volatile u32 dtlb_lo3;
 185
 186         u32 _unused34[0x0392];
 187
 188         u32 _unused35;
 189         volatile u32 rpsscounter;       /* Chirps at 100ns */
 190
 191         u32 _unused36[0x1000/4-2*4];
 192
 193         u32 _unused37;
 194         volatile u32 maddronly;         /* Address DMA goes at */
 195         u32 _unused38;
 196         volatile u32 maddrpdeflts;      /* Same as above, plus set defaults */
 197         u32 _unused39;
 198         volatile u32 dmasz;             /* DMA count */
 199         u32 _unused40;
 200         volatile u32 ssize;             /* DMA stride size */
 201         u32 _unused41;
 202         volatile u32 gmaddronly;        /* Set GIO DMA but don't start trans */
 203         u32 _unused42;
 204         volatile u32 dmaddnpgo;         /* Set GIO DMA addr + start transfer */
 205         u32 _unused43;
 206         volatile u32 dmamode;           /* DMA mode config bit settings */
 207         u32 _unused44;
 208         volatile u32 dmaccount;         /* Zoom and byte count for DMA */
 209         u32 _unused45;
 210         volatile u32 dmastart;          /* Pedal to the metal. */
 211         u32 _unused46;
 212         volatile u32 dmarunning;        /* DMA op is in progress */
 213         u32 _unused47;
 214         volatile u32 maddrdefstart;     /* Set dma addr, defaults, and kick it */
 215 };
 216
 217 extern struct sgimc_regs *sgimc;
 218 #define SGIMC_BASE              0x1fa00000      /* physical */
 219
 220 /* Base location of the two ram banks found in IP2[0268] machines. */
 221 #define SGIMC_SEG0_BADDR        0x08000000
 222 #define SGIMC_SEG1_BADDR        0x20000000
 223
 224 /* Maximum size of the above banks are per machine. */
 225 #define SGIMC_SEG0_SIZE_ALL             0x10000000 /* 256MB */
 226 #define SGIMC_SEG1_SIZE_IP20_IP22       0x08000000 /* 128MB */
 227 #define SGIMC_SEG1_SIZE_IP26_IP28       0x20000000 /* 512MB */
 228
 229 extern void sgimc_init(void);
 230
 231 #endif /* _SGI_MC_H */