Initial commit
[wrt350n-kernel.git] / drivers / usb / gadget / fsl_usb2_udc.h
blob9fb0b1ec85266322054422db511f337e53459efd
1 /*
2 * Freescale USB device/endpoint management registers
3 */
4 #ifndef __FSL_USB2_UDC_H
5 #define __FSL_USB2_UDC_H
7 /* ### define USB registers here
8 */
9 #define USB_MAX_CTRL_PAYLOAD 64
10 #define USB_DR_SYS_OFFSET 0x400
12 /* USB DR device mode registers (Little Endian) */
13 struct usb_dr_device {
14 /* Capability register */
15 u8 res1[256];
16 u16 caplength; /* Capability Register Length */
17 u16 hciversion; /* Host Controller Interface Version */
18 u32 hcsparams; /* Host Controller Structual Parameters */
19 u32 hccparams; /* Host Controller Capability Parameters */
20 u8 res2[20];
21 u32 dciversion; /* Device Controller Interface Version */
22 u32 dccparams; /* Device Controller Capability Parameters */
23 u8 res3[24];
24 /* Operation register */
25 u32 usbcmd; /* USB Command Register */
26 u32 usbsts; /* USB Status Register */
27 u32 usbintr; /* USB Interrupt Enable Register */
28 u32 frindex; /* Frame Index Register */
29 u8 res4[4];
30 u32 deviceaddr; /* Device Address */
31 u32 endpointlistaddr; /* Endpoint List Address Register */
32 u8 res5[4];
33 u32 burstsize; /* Master Interface Data Burst Size Register */
34 u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */
35 u8 res6[24];
36 u32 configflag; /* Configure Flag Register */
37 u32 portsc1; /* Port 1 Status and Control Register */
38 u8 res7[28];
39 u32 otgsc; /* On-The-Go Status and Control */
40 u32 usbmode; /* USB Mode Register */
41 u32 endptsetupstat; /* Endpoint Setup Status Register */
42 u32 endpointprime; /* Endpoint Initialization Register */
43 u32 endptflush; /* Endpoint Flush Register */
44 u32 endptstatus; /* Endpoint Status Register */
45 u32 endptcomplete; /* Endpoint Complete Register */
46 u32 endptctrl[6]; /* Endpoint Control Registers */
49 /* USB DR host mode registers (Little Endian) */
50 struct usb_dr_host {
51 /* Capability register */
52 u8 res1[256];
53 u16 caplength; /* Capability Register Length */
54 u16 hciversion; /* Host Controller Interface Version */
55 u32 hcsparams; /* Host Controller Structual Parameters */
56 u32 hccparams; /* Host Controller Capability Parameters */
57 u8 res2[20];
58 u32 dciversion; /* Device Controller Interface Version */
59 u32 dccparams; /* Device Controller Capability Parameters */
60 u8 res3[24];
61 /* Operation register */
62 u32 usbcmd; /* USB Command Register */
63 u32 usbsts; /* USB Status Register */
64 u32 usbintr; /* USB Interrupt Enable Register */
65 u32 frindex; /* Frame Index Register */
66 u8 res4[4];
67 u32 periodiclistbase; /* Periodic Frame List Base Address Register */
68 u32 asynclistaddr; /* Current Asynchronous List Address Register */
69 u8 res5[4];
70 u32 burstsize; /* Master Interface Data Burst Size Register */
71 u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */
72 u8 res6[24];
73 u32 configflag; /* Configure Flag Register */
74 u32 portsc1; /* Port 1 Status and Control Register */
75 u8 res7[28];
76 u32 otgsc; /* On-The-Go Status and Control */
77 u32 usbmode; /* USB Mode Register */
78 u32 endptsetupstat; /* Endpoint Setup Status Register */
79 u32 endpointprime; /* Endpoint Initialization Register */
80 u32 endptflush; /* Endpoint Flush Register */
81 u32 endptstatus; /* Endpoint Status Register */
82 u32 endptcomplete; /* Endpoint Complete Register */
83 u32 endptctrl[6]; /* Endpoint Control Registers */
86 /* non-EHCI USB system interface registers (Big Endian) */
87 struct usb_sys_interface {
88 u32 snoop1;
89 u32 snoop2;
90 u32 age_cnt_thresh; /* Age Count Threshold Register */
91 u32 pri_ctrl; /* Priority Control Register */
92 u32 si_ctrl; /* System Interface Control Register */
93 u8 res[236];
94 u32 control; /* General Purpose Control Register */
97 /* ep0 transfer state */
98 #define WAIT_FOR_SETUP 0
99 #define DATA_STATE_XMIT 1
100 #define DATA_STATE_NEED_ZLP 2
101 #define WAIT_FOR_OUT_STATUS 3
102 #define DATA_STATE_RECV 4
104 /* Device Controller Capability Parameter register */
105 #define DCCPARAMS_DC 0x00000080
106 #define DCCPARAMS_DEN_MASK 0x0000001f
108 /* Frame Index Register Bit Masks */
109 #define USB_FRINDEX_MASKS 0x3fff
110 /* USB CMD Register Bit Masks */
111 #define USB_CMD_RUN_STOP 0x00000001
112 #define USB_CMD_CTRL_RESET 0x00000002
113 #define USB_CMD_PERIODIC_SCHEDULE_EN 0x00000010
114 #define USB_CMD_ASYNC_SCHEDULE_EN 0x00000020
115 #define USB_CMD_INT_AA_DOORBELL 0x00000040
116 #define USB_CMD_ASP 0x00000300
117 #define USB_CMD_ASYNC_SCH_PARK_EN 0x00000800
118 #define USB_CMD_SUTW 0x00002000
119 #define USB_CMD_ATDTW 0x00004000
120 #define USB_CMD_ITC 0x00FF0000
122 /* bit 15,3,2 are frame list size */
123 #define USB_CMD_FRAME_SIZE_1024 0x00000000
124 #define USB_CMD_FRAME_SIZE_512 0x00000004
125 #define USB_CMD_FRAME_SIZE_256 0x00000008
126 #define USB_CMD_FRAME_SIZE_128 0x0000000C
127 #define USB_CMD_FRAME_SIZE_64 0x00008000
128 #define USB_CMD_FRAME_SIZE_32 0x00008004
129 #define USB_CMD_FRAME_SIZE_16 0x00008008
130 #define USB_CMD_FRAME_SIZE_8 0x0000800C
132 /* bit 9-8 are async schedule park mode count */
133 #define USB_CMD_ASP_00 0x00000000
134 #define USB_CMD_ASP_01 0x00000100
135 #define USB_CMD_ASP_10 0x00000200
136 #define USB_CMD_ASP_11 0x00000300
137 #define USB_CMD_ASP_BIT_POS 8
139 /* bit 23-16 are interrupt threshold control */
140 #define USB_CMD_ITC_NO_THRESHOLD 0x00000000
141 #define USB_CMD_ITC_1_MICRO_FRM 0x00010000
142 #define USB_CMD_ITC_2_MICRO_FRM 0x00020000
143 #define USB_CMD_ITC_4_MICRO_FRM 0x00040000
144 #define USB_CMD_ITC_8_MICRO_FRM 0x00080000
145 #define USB_CMD_ITC_16_MICRO_FRM 0x00100000
146 #define USB_CMD_ITC_32_MICRO_FRM 0x00200000
147 #define USB_CMD_ITC_64_MICRO_FRM 0x00400000
148 #define USB_CMD_ITC_BIT_POS 16
150 /* USB STS Register Bit Masks */
151 #define USB_STS_INT 0x00000001
152 #define USB_STS_ERR 0x00000002
153 #define USB_STS_PORT_CHANGE 0x00000004
154 #define USB_STS_FRM_LST_ROLL 0x00000008
155 #define USB_STS_SYS_ERR 0x00000010
156 #define USB_STS_IAA 0x00000020
157 #define USB_STS_RESET 0x00000040
158 #define USB_STS_SOF 0x00000080
159 #define USB_STS_SUSPEND 0x00000100
160 #define USB_STS_HC_HALTED 0x00001000
161 #define USB_STS_RCL 0x00002000
162 #define USB_STS_PERIODIC_SCHEDULE 0x00004000
163 #define USB_STS_ASYNC_SCHEDULE 0x00008000
165 /* USB INTR Register Bit Masks */
166 #define USB_INTR_INT_EN 0x00000001
167 #define USB_INTR_ERR_INT_EN 0x00000002
168 #define USB_INTR_PTC_DETECT_EN 0x00000004
169 #define USB_INTR_FRM_LST_ROLL_EN 0x00000008
170 #define USB_INTR_SYS_ERR_EN 0x00000010
171 #define USB_INTR_ASYN_ADV_EN 0x00000020
172 #define USB_INTR_RESET_EN 0x00000040
173 #define USB_INTR_SOF_EN 0x00000080
174 #define USB_INTR_DEVICE_SUSPEND 0x00000100
176 /* Device Address bit masks */
177 #define USB_DEVICE_ADDRESS_MASK 0xFE000000
178 #define USB_DEVICE_ADDRESS_BIT_POS 25
180 /* endpoint list address bit masks */
181 #define USB_EP_LIST_ADDRESS_MASK 0xfffff800
183 /* PORTSCX Register Bit Masks */
184 #define PORTSCX_CURRENT_CONNECT_STATUS 0x00000001
185 #define PORTSCX_CONNECT_STATUS_CHANGE 0x00000002
186 #define PORTSCX_PORT_ENABLE 0x00000004
187 #define PORTSCX_PORT_EN_DIS_CHANGE 0x00000008
188 #define PORTSCX_OVER_CURRENT_ACT 0x00000010
189 #define PORTSCX_OVER_CURRENT_CHG 0x00000020
190 #define PORTSCX_PORT_FORCE_RESUME 0x00000040
191 #define PORTSCX_PORT_SUSPEND 0x00000080
192 #define PORTSCX_PORT_RESET 0x00000100
193 #define PORTSCX_LINE_STATUS_BITS 0x00000C00
194 #define PORTSCX_PORT_POWER 0x00001000
195 #define PORTSCX_PORT_INDICTOR_CTRL 0x0000C000
196 #define PORTSCX_PORT_TEST_CTRL 0x000F0000
197 #define PORTSCX_WAKE_ON_CONNECT_EN 0x00100000
198 #define PORTSCX_WAKE_ON_CONNECT_DIS 0x00200000
199 #define PORTSCX_WAKE_ON_OVER_CURRENT 0x00400000
200 #define PORTSCX_PHY_LOW_POWER_SPD 0x00800000
201 #define PORTSCX_PORT_FORCE_FULL_SPEED 0x01000000
202 #define PORTSCX_PORT_SPEED_MASK 0x0C000000
203 #define PORTSCX_PORT_WIDTH 0x10000000
204 #define PORTSCX_PHY_TYPE_SEL 0xC0000000
206 /* bit 11-10 are line status */
207 #define PORTSCX_LINE_STATUS_SE0 0x00000000
208 #define PORTSCX_LINE_STATUS_JSTATE 0x00000400
209 #define PORTSCX_LINE_STATUS_KSTATE 0x00000800
210 #define PORTSCX_LINE_STATUS_UNDEF 0x00000C00
211 #define PORTSCX_LINE_STATUS_BIT_POS 10
213 /* bit 15-14 are port indicator control */
214 #define PORTSCX_PIC_OFF 0x00000000
215 #define PORTSCX_PIC_AMBER 0x00004000
216 #define PORTSCX_PIC_GREEN 0x00008000
217 #define PORTSCX_PIC_UNDEF 0x0000C000
218 #define PORTSCX_PIC_BIT_POS 14
220 /* bit 19-16 are port test control */
221 #define PORTSCX_PTC_DISABLE 0x00000000
222 #define PORTSCX_PTC_JSTATE 0x00010000
223 #define PORTSCX_PTC_KSTATE 0x00020000
224 #define PORTSCX_PTC_SEQNAK 0x00030000
225 #define PORTSCX_PTC_PACKET 0x00040000
226 #define PORTSCX_PTC_FORCE_EN 0x00050000
227 #define PORTSCX_PTC_BIT_POS 16
229 /* bit 27-26 are port speed */
230 #define PORTSCX_PORT_SPEED_FULL 0x00000000
231 #define PORTSCX_PORT_SPEED_LOW 0x04000000
232 #define PORTSCX_PORT_SPEED_HIGH 0x08000000
233 #define PORTSCX_PORT_SPEED_UNDEF 0x0C000000
234 #define PORTSCX_SPEED_BIT_POS 26
236 /* bit 28 is parallel transceiver width for UTMI interface */
237 #define PORTSCX_PTW 0x10000000
238 #define PORTSCX_PTW_8BIT 0x00000000
239 #define PORTSCX_PTW_16BIT 0x10000000
241 /* bit 31-30 are port transceiver select */
242 #define PORTSCX_PTS_UTMI 0x00000000
243 #define PORTSCX_PTS_ULPI 0x80000000
244 #define PORTSCX_PTS_FSLS 0xC0000000
245 #define PORTSCX_PTS_BIT_POS 30
247 /* otgsc Register Bit Masks */
248 #define OTGSC_CTRL_VUSB_DISCHARGE 0x00000001
249 #define OTGSC_CTRL_VUSB_CHARGE 0x00000002
250 #define OTGSC_CTRL_OTG_TERM 0x00000008
251 #define OTGSC_CTRL_DATA_PULSING 0x00000010
252 #define OTGSC_STS_USB_ID 0x00000100
253 #define OTGSC_STS_A_VBUS_VALID 0x00000200
254 #define OTGSC_STS_A_SESSION_VALID 0x00000400
255 #define OTGSC_STS_B_SESSION_VALID 0x00000800
256 #define OTGSC_STS_B_SESSION_END 0x00001000
257 #define OTGSC_STS_1MS_TOGGLE 0x00002000
258 #define OTGSC_STS_DATA_PULSING 0x00004000
259 #define OTGSC_INTSTS_USB_ID 0x00010000
260 #define OTGSC_INTSTS_A_VBUS_VALID 0x00020000
261 #define OTGSC_INTSTS_A_SESSION_VALID 0x00040000
262 #define OTGSC_INTSTS_B_SESSION_VALID 0x00080000
263 #define OTGSC_INTSTS_B_SESSION_END 0x00100000
264 #define OTGSC_INTSTS_1MS 0x00200000
265 #define OTGSC_INTSTS_DATA_PULSING 0x00400000
266 #define OTGSC_INTR_USB_ID 0x01000000
267 #define OTGSC_INTR_A_VBUS_VALID 0x02000000
268 #define OTGSC_INTR_A_SESSION_VALID 0x04000000
269 #define OTGSC_INTR_B_SESSION_VALID 0x08000000
270 #define OTGSC_INTR_B_SESSION_END 0x10000000
271 #define OTGSC_INTR_1MS_TIMER 0x20000000
272 #define OTGSC_INTR_DATA_PULSING 0x40000000
274 /* USB MODE Register Bit Masks */
275 #define USB_MODE_CTRL_MODE_IDLE 0x00000000
276 #define USB_MODE_CTRL_MODE_DEVICE 0x00000002
277 #define USB_MODE_CTRL_MODE_HOST 0x00000003
278 #define USB_MODE_CTRL_MODE_RSV 0x00000001
279 #define USB_MODE_SETUP_LOCK_OFF 0x00000008
280 #define USB_MODE_STREAM_DISABLE 0x00000010
281 /* Endpoint Flush Register */
282 #define EPFLUSH_TX_OFFSET 0x00010000
283 #define EPFLUSH_RX_OFFSET 0x00000000
285 /* Endpoint Setup Status bit masks */
286 #define EP_SETUP_STATUS_MASK 0x0000003F
287 #define EP_SETUP_STATUS_EP0 0x00000001
289 /* ENDPOINTCTRLx Register Bit Masks */
290 #define EPCTRL_TX_ENABLE 0x00800000
291 #define EPCTRL_TX_DATA_TOGGLE_RST 0x00400000 /* Not EP0 */
292 #define EPCTRL_TX_DATA_TOGGLE_INH 0x00200000 /* Not EP0 */
293 #define EPCTRL_TX_TYPE 0x000C0000
294 #define EPCTRL_TX_DATA_SOURCE 0x00020000 /* Not EP0 */
295 #define EPCTRL_TX_EP_STALL 0x00010000
296 #define EPCTRL_RX_ENABLE 0x00000080
297 #define EPCTRL_RX_DATA_TOGGLE_RST 0x00000040 /* Not EP0 */
298 #define EPCTRL_RX_DATA_TOGGLE_INH 0x00000020 /* Not EP0 */
299 #define EPCTRL_RX_TYPE 0x0000000C
300 #define EPCTRL_RX_DATA_SINK 0x00000002 /* Not EP0 */
301 #define EPCTRL_RX_EP_STALL 0x00000001
303 /* bit 19-18 and 3-2 are endpoint type */
304 #define EPCTRL_EP_TYPE_CONTROL 0
305 #define EPCTRL_EP_TYPE_ISO 1
306 #define EPCTRL_EP_TYPE_BULK 2
307 #define EPCTRL_EP_TYPE_INTERRUPT 3
308 #define EPCTRL_TX_EP_TYPE_SHIFT 18
309 #define EPCTRL_RX_EP_TYPE_SHIFT 2
311 /* SNOOPn Register Bit Masks */
312 #define SNOOP_ADDRESS_MASK 0xFFFFF000
313 #define SNOOP_SIZE_ZERO 0x00 /* snooping disable */
314 #define SNOOP_SIZE_4KB 0x0B /* 4KB snoop size */
315 #define SNOOP_SIZE_8KB 0x0C
316 #define SNOOP_SIZE_16KB 0x0D
317 #define SNOOP_SIZE_32KB 0x0E
318 #define SNOOP_SIZE_64KB 0x0F
319 #define SNOOP_SIZE_128KB 0x10
320 #define SNOOP_SIZE_256KB 0x11
321 #define SNOOP_SIZE_512KB 0x12
322 #define SNOOP_SIZE_1MB 0x13
323 #define SNOOP_SIZE_2MB 0x14
324 #define SNOOP_SIZE_4MB 0x15
325 #define SNOOP_SIZE_8MB 0x16
326 #define SNOOP_SIZE_16MB 0x17
327 #define SNOOP_SIZE_32MB 0x18
328 #define SNOOP_SIZE_64MB 0x19
329 #define SNOOP_SIZE_128MB 0x1A
330 #define SNOOP_SIZE_256MB 0x1B
331 #define SNOOP_SIZE_512MB 0x1C
332 #define SNOOP_SIZE_1GB 0x1D
333 #define SNOOP_SIZE_2GB 0x1E /* 2GB snoop size */
335 /* pri_ctrl Register Bit Masks */
336 #define PRI_CTRL_PRI_LVL1 0x0000000C
337 #define PRI_CTRL_PRI_LVL0 0x00000003
339 /* si_ctrl Register Bit Masks */
340 #define SI_CTRL_ERR_DISABLE 0x00000010
341 #define SI_CTRL_IDRC_DISABLE 0x00000008
342 #define SI_CTRL_RD_SAFE_EN 0x00000004
343 #define SI_CTRL_RD_PREFETCH_DISABLE 0x00000002
344 #define SI_CTRL_RD_PREFEFETCH_VAL 0x00000001
346 /* control Register Bit Masks */
347 #define USB_CTRL_IOENB 0x00000004
348 #define USB_CTRL_ULPI_INT0EN 0x00000001
350 /* Endpoint Queue Head data struct
351 * Rem: all the variables of qh are LittleEndian Mode
352 * and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr
354 struct ep_queue_head {
355 u32 max_pkt_length; /* Mult(31-30) , Zlt(29) , Max Pkt len
356 and IOS(15) */
357 u32 curr_dtd_ptr; /* Current dTD Pointer(31-5) */
358 u32 next_dtd_ptr; /* Next dTD Pointer(31-5), T(0) */
359 u32 size_ioc_int_sts; /* Total bytes (30-16), IOC (15),
360 MultO(11-10), STS (7-0) */
361 u32 buff_ptr0; /* Buffer pointer Page 0 (31-12) */
362 u32 buff_ptr1; /* Buffer pointer Page 1 (31-12) */
363 u32 buff_ptr2; /* Buffer pointer Page 2 (31-12) */
364 u32 buff_ptr3; /* Buffer pointer Page 3 (31-12) */
365 u32 buff_ptr4; /* Buffer pointer Page 4 (31-12) */
366 u32 res1;
367 u8 setup_buffer[8]; /* Setup data 8 bytes */
368 u32 res2[4];
371 /* Endpoint Queue Head Bit Masks */
372 #define EP_QUEUE_HEAD_MULT_POS 30
373 #define EP_QUEUE_HEAD_ZLT_SEL 0x20000000
374 #define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16
375 #define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff)
376 #define EP_QUEUE_HEAD_IOS 0x00008000
377 #define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001
378 #define EP_QUEUE_HEAD_IOC 0x00008000
379 #define EP_QUEUE_HEAD_MULTO 0x00000C00
380 #define EP_QUEUE_HEAD_STATUS_HALT 0x00000040
381 #define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080
382 #define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF
383 #define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0
384 #define EP_QUEUE_FRINDEX_MASK 0x000007FF
385 #define EP_MAX_LENGTH_TRANSFER 0x4000
387 /* Endpoint Transfer Descriptor data struct */
388 /* Rem: all the variables of td are LittleEndian Mode */
389 struct ep_td_struct {
390 u32 next_td_ptr; /* Next TD pointer(31-5), T(0) set
391 indicate invalid */
392 u32 size_ioc_sts; /* Total bytes (30-16), IOC (15),
393 MultO(11-10), STS (7-0) */
394 u32 buff_ptr0; /* Buffer pointer Page 0 */
395 u32 buff_ptr1; /* Buffer pointer Page 1 */
396 u32 buff_ptr2; /* Buffer pointer Page 2 */
397 u32 buff_ptr3; /* Buffer pointer Page 3 */
398 u32 buff_ptr4; /* Buffer pointer Page 4 */
399 u32 res;
400 /* 32 bytes */
401 dma_addr_t td_dma; /* dma address for this td */
402 /* virtual address of next td specified in next_td_ptr */
403 struct ep_td_struct *next_td_virt;
406 /* Endpoint Transfer Descriptor bit Masks */
407 #define DTD_NEXT_TERMINATE 0x00000001
408 #define DTD_IOC 0x00008000
409 #define DTD_STATUS_ACTIVE 0x00000080
410 #define DTD_STATUS_HALTED 0x00000040
411 #define DTD_STATUS_DATA_BUFF_ERR 0x00000020
412 #define DTD_STATUS_TRANSACTION_ERR 0x00000008
413 #define DTD_RESERVED_FIELDS 0x80007300
414 #define DTD_ADDR_MASK 0xFFFFFFE0
415 #define DTD_PACKET_SIZE 0x7FFF0000
416 #define DTD_LENGTH_BIT_POS 16
417 #define DTD_ERROR_MASK (DTD_STATUS_HALTED | \
418 DTD_STATUS_DATA_BUFF_ERR | \
419 DTD_STATUS_TRANSACTION_ERR)
420 /* Alignment requirements; must be a power of two */
421 #define DTD_ALIGNMENT 0x20
422 #define QH_ALIGNMENT 2048
424 /* Controller dma boundary */
425 #define UDC_DMA_BOUNDARY 0x1000
427 /* -----------------------------------------------------------------------*/
428 /* ##### enum data
430 typedef enum {
431 e_ULPI,
432 e_UTMI_8BIT,
433 e_UTMI_16BIT,
434 e_SERIAL
435 } e_PhyInterface;
437 /*-------------------------------------------------------------------------*/
439 /* ### driver private data
441 struct fsl_req {
442 struct usb_request req;
443 struct list_head queue;
444 /* ep_queue() func will add
445 a request->queue into a udc_ep->queue 'd tail */
446 struct fsl_ep *ep;
447 unsigned mapped:1;
449 struct ep_td_struct *head, *tail; /* For dTD List
450 cpu endian Virtual addr */
451 unsigned int dtd_count;
454 #define REQ_UNCOMPLETE 1
456 struct fsl_ep {
457 struct usb_ep ep;
458 struct list_head queue;
459 struct fsl_udc *udc;
460 struct ep_queue_head *qh;
461 const struct usb_endpoint_descriptor *desc;
462 struct usb_gadget *gadget;
464 char name[14];
465 unsigned stopped:1;
468 #define EP_DIR_IN 1
469 #define EP_DIR_OUT 0
471 struct fsl_udc {
473 struct usb_gadget gadget;
474 struct usb_gadget_driver *driver;
475 struct fsl_ep *eps;
476 unsigned int max_ep;
477 unsigned int irq;
479 struct usb_ctrlrequest local_setup_buff;
480 spinlock_t lock;
481 struct otg_transceiver *transceiver;
482 unsigned softconnect:1;
483 unsigned vbus_active:1;
484 unsigned stopped:1;
485 unsigned remote_wakeup:1;
487 struct ep_queue_head *ep_qh; /* Endpoints Queue-Head */
488 struct fsl_req *status_req; /* ep0 status request */
489 struct dma_pool *td_pool; /* dma pool for DTD */
490 enum fsl_usb2_phy_modes phy_mode;
492 size_t ep_qh_size; /* size after alignment adjustment*/
493 dma_addr_t ep_qh_dma; /* dma address of QH */
495 u32 max_pipes; /* Device max pipes */
496 u32 max_use_endpts; /* Max endpointes to be used */
497 u32 bus_reset; /* Device is bus reseting */
498 u32 resume_state; /* USB state to resume */
499 u32 usb_state; /* USB current state */
500 u32 usb_next_state; /* USB next state */
501 u32 ep0_state; /* Endpoint zero state */
502 u32 ep0_dir; /* Endpoint zero direction: can be
503 USB_DIR_IN or USB_DIR_OUT */
504 u32 usb_sof_count; /* SOF count */
505 u32 errors; /* USB ERRORs count */
506 u8 device_address; /* Device USB address */
508 struct completion *done; /* to make sure release() is done */
511 /*-------------------------------------------------------------------------*/
513 #ifdef DEBUG
514 #define DBG(fmt, args...) printk(KERN_DEBUG "[%s] " fmt "\n", \
515 __FUNCTION__, ## args)
516 #else
517 #define DBG(fmt, args...) do{}while(0)
518 #endif
520 #if 0
521 static void dump_msg(const char *label, const u8 * buf, unsigned int length)
523 unsigned int start, num, i;
524 char line[52], *p;
526 if (length >= 512)
527 return;
528 DBG("%s, length %u:\n", label, length);
529 start = 0;
530 while (length > 0) {
531 num = min(length, 16u);
532 p = line;
533 for (i = 0; i < num; ++i) {
534 if (i == 8)
535 *p++ = ' ';
536 sprintf(p, " %02x", buf[i]);
537 p += 3;
539 *p = 0;
540 printk(KERN_DEBUG "%6x: %s\n", start, line);
541 buf += num;
542 start += num;
543 length -= num;
546 #endif
548 #ifdef VERBOSE
549 #define VDBG DBG
550 #else
551 #define VDBG(stuff...) do{}while(0)
552 #endif
554 #define ERR(stuff...) pr_err("udc: " stuff)
555 #define WARN(stuff...) pr_warning("udc: " stuff)
556 #define INFO(stuff...) pr_info("udc: " stuff)
558 /*-------------------------------------------------------------------------*/
560 /* ### Add board specific defines here
564 * ### pipe direction macro from device view
566 #define USB_RECV 0 /* OUT EP */
567 #define USB_SEND 1 /* IN EP */
570 * ### internal used help routines.
572 #define ep_index(EP) ((EP)->desc->bEndpointAddress&0xF)
573 #define ep_maxpacket(EP) ((EP)->ep.maxpacket)
574 #define ep_is_in(EP) ( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \
575 USB_DIR_IN ):((EP)->desc->bEndpointAddress \
576 & USB_DIR_IN)==USB_DIR_IN)
577 #define get_ep_by_pipe(udc, pipe) ((pipe == 1)? &udc->eps[0]: \
578 &udc->eps[pipe])
579 #define get_pipe_by_windex(windex) ((windex & USB_ENDPOINT_NUMBER_MASK) \
580 * 2 + ((windex & USB_DIR_IN) ? 1 : 0))
581 #define get_pipe_by_ep(EP) (ep_index(EP) * 2 + ep_is_in(EP))
583 #endif