include/asm-arm/arch-ixp2000/platform.h

   1 /*
   2  * include/asm-arm/arch-ixp2000/platform.h
   3  *
   4  * Various bits of code used by platform-level code.
   5  *
   6  * Author: Deepak Saxena <dsaxena@plexity.net>
   7  *
   8  * Copyright 2004 (c) MontaVista Software, Inc.
   9  *
  10  * This file is licensed under  the terms of the GNU General Public
  11  * License version 2. This program is licensed "as is" without any
  12  * warranty of any kind, whether express or implied.
  13  */
  14
  15
  16 #ifndef __ASSEMBLY__
  17
  18 static inline unsigned long ixp2000_reg_read(volatile void *reg)
  19 {
  20         return *((volatile unsigned long *)reg);
  21 }
  22
  23 static inline void ixp2000_reg_write(volatile void *reg, unsigned long val)
  24 {
  25         *((volatile unsigned long *)reg) = val;
  26 }
  27
  28 /*
  29  * On the IXP2400, we can't use XCB=000 due to chip bugs.  We use
  30  * XCB=101 instead, but that makes all I/O accesses bufferable.  This
  31  * is not a problem in general, but we do have to be slightly more
  32  * careful because I/O writes are no longer automatically flushed out
  33  * of the write buffer.
  34  *
  35  * In cases where we want to make sure that a write has been flushed
  36  * out of the write buffer before we proceed, for example when masking
  37  * a device interrupt before re-enabling IRQs in CPSR, we can use this
  38  * function, ixp2000_reg_wrb, which performs a write, a readback, and
  39  * issues a dummy instruction dependent on the value of the readback
  40  * (mov rX, rX) to make sure that the readback has completed before we
  41  * continue.
  42  */
  43 static inline void ixp2000_reg_wrb(volatile void *reg, unsigned long val)
  44 {
  45         unsigned long dummy;
  46
  47         *((volatile unsigned long *)reg) = val;
  48
  49         dummy = *((volatile unsigned long *)reg);
  50         __asm__ __volatile__("mov %0, %0" : "+r" (dummy));
  51 }
  52
  53 /*
  54  * Boards may multiplex different devices on the 2nd channel of
  55  * the slowport interface that each need different configuration
  56  * settings.  For example, the IXDP2400 uses channel 2 on the interface
  57  * to access the CPLD, the switch fabric card, and the media card.  Each
  58  * one needs a different mode so drivers must save/restore the mode
  59  * before and after each operation.
  60  *
  61  * acquire_slowport(&your_config);
  62  * ...
  63  * do slowport operations
  64  * ...
  65  * release_slowport();
  66  *
  67  * Note that while you have the slowport, you are holding a spinlock,
  68  * so your code should be written as if you explicitly acquired a lock.
  69  *
  70  * The configuration only affects device 2 on the slowport, so the
  71  * MTD map driver does not acquire/release the slowport.
  72  */
  73 struct slowport_cfg {
  74         unsigned long CCR;      /* Clock divide */
  75         unsigned long WTC;      /* Write Timing Control */
  76         unsigned long RTC;      /* Read Timing Control */
  77         unsigned long PCR;      /* Protocol Control Register */
  78         unsigned long ADC;      /* Address/Data Width Control */
  79 };
  80
  81
  82 void ixp2000_acquire_slowport(struct slowport_cfg *, struct slowport_cfg *);
  83 void ixp2000_release_slowport(struct slowport_cfg *);
  84
  85 /*
  86  * IXP2400 A0/A1 and  IXP2800 A0/A1/A2 have broken slowport that requires
  87  * tweaking of addresses in the MTD driver.
  88  */
  89 static inline unsigned ixp2000_has_broken_slowport(void)
  90 {
  91         unsigned long id = *IXP2000_PRODUCT_ID;
  92         unsigned long id_prod = id & (IXP2000_MAJ_PROD_TYPE_MASK |
  93                                       IXP2000_MIN_PROD_TYPE_MASK);
  94         return (((id_prod ==
  95                   /* fixed in IXP2400-B0 */
  96                   (IXP2000_MAJ_PROD_TYPE_IXP2000 |
  97                    IXP2000_MIN_PROD_TYPE_IXP2400)) &&
  98                  ((id & IXP2000_MAJ_REV_MASK) == 0)) ||
  99                 ((id_prod ==
 100                   /* fixed in IXP2800-B0 */
 101                   (IXP2000_MAJ_PROD_TYPE_IXP2000 |
 102                    IXP2000_MIN_PROD_TYPE_IXP2800)) &&
 103                  ((id & IXP2000_MAJ_REV_MASK) == 0)) ||
 104                 ((id_prod ==
 105                   /* fixed in IXP2850-B0 */
 106                   (IXP2000_MAJ_PROD_TYPE_IXP2000 |
 107                    IXP2000_MIN_PROD_TYPE_IXP2850)) &&
 108                  ((id & IXP2000_MAJ_REV_MASK) == 0)));
 109 }
 110
 111 static inline unsigned int ixp2000_has_flash(void)
 112 {
 113         return ((*IXP2000_STRAP_OPTIONS) & (CFG_BOOT_PROM));
 114 }
 115
 116 static inline unsigned int ixp2000_is_pcimaster(void)
 117 {
 118         return ((*IXP2000_STRAP_OPTIONS) & (CFG_PCI_BOOT_HOST));
 119 }
 120
 121 void ixp2000_map_io(void);
 122 void ixp2000_uart_init(void);
 123 void ixp2000_init_irq(void);
 124 void ixp2000_init_time(unsigned long);
 125 unsigned long ixp2000_gettimeoffset(void);
 126
 127 struct pci_sys_data;
 128
 129 u32 *ixp2000_pci_config_addr(unsigned int bus, unsigned int devfn, int where);
 130 void ixp2000_pci_preinit(void);
 131 int ixp2000_pci_setup(int, struct pci_sys_data*);
 132 struct pci_bus* ixp2000_pci_scan_bus(int, struct pci_sys_data*);
 133 int ixp2000_pci_read_config(struct pci_bus*, unsigned int, int, int, u32 *);
 134 int ixp2000_pci_write_config(struct pci_bus*, unsigned int, int, int, u32);
 135
 136 /*
 137  * Several of the IXP2000 systems have banked flash so we need to extend the
 138  * flash_platform_data structure with some private pointers
 139  */
 140 struct ixp2000_flash_data {
 141         struct flash_platform_data *platform_data;
 142         int nr_banks;
 143         unsigned long (*bank_setup)(unsigned long);
 144 };
 145
 146 struct ixp2000_i2c_pins {
 147         unsigned long sda_pin;
 148         unsigned long scl_pin;
 149 };
 150
 151
 152 #endif /*  !__ASSEMBLY__ */