1 menu "Bus options (PCI, PCMCIA, EISA, GSC, ISA)"
4 bool "VSC/GSC/HSC bus support"
7 The VSC, GSC and HSC busses were used from the earliest 700-series
8 workstations up to and including the C360/J2240 workstations. They
9 were also used in servers from the E-class to the K-class. They
10 are not found in B1000, C3000, J5000, A500, L1000, N4000 and upwards.
14 bool "HP-PB bus support"
17 The HP-PB bus was used in the Nova class and K-class servers.
21 bool "U2/Uturn I/O MMU"
24 Say Y here to enable DMA management routines for the first
25 generation of PA-RISC cache-coherent machines. Programs the
26 U2/Uturn chip in "Virtual Mode" and use the I/O MMU.
29 bool "Lasi I/O support"
32 Say Y here to support the Lasi multifunction chip found in
33 many PA-RISC workstations & servers. It includes interfaces
34 for a parallel port, serial port, NCR 53c710 SCSI, Apricot
35 Ethernet, Harmony audio, PS/2 keyboard & mouse, ISDN, telephony
36 and floppy. Note that you must still enable all the individual
37 drivers for these chips.
40 bool "Wax I/O support"
43 Say Y here to support the Wax multifunction chip found in some
44 older systems, including B/C/D/R class and 715/64, 715/80 and
45 715/100. Wax includes an EISA adapter, a serial port (not always
46 used), a HIL interface chip and is also known to be used as the
47 GSC bridge for an X.25 GSC card.
53 Say Y here if you have an EISA bus in your machine. This code
54 supports both the Mongoose & Wax EISA adapters. It is sadly
55 incomplete and lacks support for card-to-host DMA.
57 source "drivers/eisa/Kconfig"
63 If you want to plug an ISA card into your EISA bus, say Y here.
64 Most people should say N.
69 All recent HP machines have PCI slots, and you should say Y here
70 if you have a recent machine. If you are convinced you do not have
71 PCI slots in your machine (eg a 712), then you may say "N" here.
72 Beware that some GSC cards have a Dino onboard and PCI inside them,
73 so it may be safest to say "Y" anyway.
75 source "drivers/pci/Kconfig"
78 bool "GSCtoPCI/Dino PCI support"
81 Say Y here to support the Dino & Cujo GSC to PCI bridges found in
82 machines from the B132 to the C360, the J2240 and the A180. Some
83 GSC/HSC cards (eg gigabit & dual 100 Mbit Ethernet) have a Dino on
84 the card, and you also need to say Y here if you have such a card.
85 Note that Dino also supplies one of the serial ports on certain
86 machines. If in doubt, say Y.
89 bool "LBA/Elroy PCI support"
92 Say Y here to support the Elroy PCI Lower Bus Adapter. This is
93 present on B, C, J, L and N-class machines with 4-digit model
94 numbers and the A400/A500.
106 <<<<<<< HEAD:drivers/parisc/Kconfig
110 depends on IOMMU_SBA || IOMMU_CCIO
113 >>>>>>> 264e3e889d86e552b4191d69bb60f4f3b383135a:drivers/parisc/Kconfig
115 # bool "EPIC/SAGA PCI support"
119 # Say Y here for V-class PCI, DMA/IOMMU, IRQ subsystem support.
121 source "drivers/pcmcia/Kconfig"
123 source "drivers/pci/hotplug/Kconfig"
127 menu "PA-RISC specific drivers"
130 bool "SuperIO (SuckyIO) support"
134 Say Y here to support the SuperIO chip found in Bxxxx, C3xxx and
135 J5xxx+ machines. This enables IDE, Floppy, Parallel Port, and
136 Serial port on those machines.
138 config CHASSIS_LCD_LED
139 bool "Chassis LCD and LED support"
142 Say Y here if you want to enable support for the Heartbeat,
143 Disk/Network activities LEDs on some PA-RISC machines,
144 or support for the LCD that can be found on recent material.
146 This has nothing to do with LED State support for A and E class.
151 bool "PDC chassis state codes support"
154 Say Y here if you want to enable support for Chassis codes.
155 That includes support for LED State front panel as found on E
156 class, and support for the GSP Virtual Front Panel (LED State and
157 message logging) as found on high end servers such as A, L and
159 This driver will also display progress messages on LCD display,
160 such as "INI", "RUN" and "FLT", and might thus clobber messages
161 shown by the LED/LCD driver.
162 This driver updates the state panel (LED and/or LCD) upon system
163 state change (eg: boot, shutdown or panic).
168 config PDC_CHASSIS_WARN
169 bool "PDC chassis warnings support"
173 Say Y here if you want to enable support for Chassis warnings.
174 This will add a proc entry '/proc/chassis' giving some information
175 about the overall health state of the system.
176 This includes NVRAM battery level, overtemp or failures such as
183 tristate "PDC Stable Storage support"
187 Say Y here if you want to enable support for accessing Stable Storage
188 variables (PDC non volatile variables such as Primary Boot Path,
189 Console Path, Autoboot, Autosearch, etc) through SysFS.
193 To compile this driver as a module, choose M here.
194 The module will be called pdc_stable.