include/asm-sh/mpc1211/dma.h

   1 /* $Id: dma.h,v 1.7 1992/12/14 00:29:34 root Exp root $
   2  * linux/include/asm/dma.h: Defines for using and allocating dma channels.
   3  * Written by Hennus Bergman, 1992.
   4  * High DMA channel support & info by Hannu Savolainen
   5  * and John Boyd, Nov. 1992.
   6  */
   7
   8 #ifndef _ASM_MPC1211_DMA_H
   9 #define _ASM_MPC1211_DMA_H
  10
  11 #include <linux/spinlock.h>     /* And spinlocks */
  12 #include <asm/io.h>             /* need byte IO */
  13 #include <linux/delay.h>
  14
  15
  16 #ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
  17 #define dma_outb        outb_p
  18 #else
  19 #define dma_outb        outb
  20 #endif
  21
  22 #define dma_inb         inb
  23
  24 /*
  25  * NOTES about DMA transfers:
  26  *
  27  *  controller 1: channels 0-3, byte operations, ports 00-1F
  28  *  controller 2: channels 4-7, word operations, ports C0-DF
  29  *
  30  *  - ALL registers are 8 bits only, regardless of transfer size
  31  *  - channel 4 is not used - cascades 1 into 2.
  32  *  - channels 0-3 are byte - addresses/counts are for physical bytes
  33  *  - channels 5-7 are word - addresses/counts are for physical words
  34  *  - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
  35  *  - transfer count loaded to registers is 1 less than actual count
  36  *  - controller 2 offsets are all even (2x offsets for controller 1)
  37  *  - page registers for 5-7 don't use data bit 0, represent 128K pages
  38  *  - page registers for 0-3 use bit 0, represent 64K pages
  39  *
  40  * DMA transfers are limited to the lower 16MB of _physical_ memory.
  41  * Note that addresses loaded into registers must be _physical_ addresses,
  42  * not logical addresses (which may differ if paging is active).
  43  *
  44  *  Address mapping for channels 0-3:
  45  *
  46  *   A23 ... A16 A15 ... A8  A7 ... A0    (Physical addresses)
  47  *    |  ...  |   |  ... |   |  ... |
  48  *    |  ...  |   |  ... |   |  ... |
  49  *    |  ...  |   |  ... |   |  ... |
  50  *   P7  ...  P0  A7 ... A0  A7 ... A0
  51  * |    Page    | Addr MSB | Addr LSB |   (DMA registers)
  52  *
  53  *  Address mapping for channels 5-7:
  54  *
  55  *   A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0    (Physical addresses)
  56  *    |  ...  |   \   \   ... \  \  \  ... \  \
  57  *    |  ...  |    \   \   ... \  \  \  ... \  (not used)
  58  *    |  ...  |     \   \   ... \  \  \  ... \
  59  *   P7  ...  P1 (0) A7 A6  ... A0 A7 A6 ... A0
  60  * |      Page      |  Addr MSB   |  Addr LSB  |   (DMA registers)
  61  *
  62  * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
  63  * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
  64  * the hardware level, so odd-byte transfers aren't possible).
  65  *
  66  * Transfer count (_not # bytes_) is limited to 64K, represented as actual
  67  * count - 1 : 64K => 0xFFFF, 1 => 0x0000.  Thus, count is always 1 or more,
  68  * and up to 128K bytes may be transferred on channels 5-7 in one operation.
  69  *
  70  */
  71
  72 #define MAX_DMA_CHANNELS        8
  73
  74 /* The maximum address that we can perform a DMA transfer to on this platform */
  75 #define MAX_DMA_ADDRESS      (PAGE_OFFSET+0x10000000)
  76
  77 /* 8237 DMA controllers */
  78 #define IO_DMA1_BASE    0x00    /* 8 bit slave DMA, channels 0..3 */
  79 #define IO_DMA2_BASE    0xC0    /* 16 bit master DMA, ch 4(=slave input)..7 */
  80
  81 /* DMA controller registers */
  82 #define DMA1_CMD_REG            0x08    /* command register (w) */
  83 #define DMA1_STAT_REG           0x08    /* status register (r) */
  84 #define DMA1_REQ_REG            0x09    /* request register (w) */
  85 #define DMA1_MASK_REG           0x0A    /* single-channel mask (w) */
  86 #define DMA1_MODE_REG           0x0B    /* mode register (w) */
  87 #define DMA1_CLEAR_FF_REG       0x0C    /* clear pointer flip-flop (w) */
  88 #define DMA1_TEMP_REG           0x0D    /* Temporary Register (r) */
  89 #define DMA1_RESET_REG          0x0D    /* Master Clear (w) */
  90 #define DMA1_CLR_MASK_REG       0x0E    /* Clear Mask */
  91 #define DMA1_MASK_ALL_REG       0x0F    /* all-channels mask (w) */
  92
  93 #define DMA2_CMD_REG            0xD0    /* command register (w) */
  94 #define DMA2_STAT_REG           0xD0    /* status register (r) */
  95 #define DMA2_REQ_REG            0xD2    /* request register (w) */
  96 #define DMA2_MASK_REG           0xD4    /* single-channel mask (w) */
  97 #define DMA2_MODE_REG           0xD6    /* mode register (w) */
  98 #define DMA2_CLEAR_FF_REG       0xD8    /* clear pointer flip-flop (w) */
  99 #define DMA2_TEMP_REG           0xDA    /* Temporary Register (r) */
 100 #define DMA2_RESET_REG          0xDA    /* Master Clear (w) */
 101 #define DMA2_CLR_MASK_REG       0xDC    /* Clear Mask */
 102 #define DMA2_MASK_ALL_REG       0xDE    /* all-channels mask (w) */
 103
 104 #define DMA_ADDR_0              0x00    /* DMA address registers */
 105 #define DMA_ADDR_1              0x02
 106 #define DMA_ADDR_2              0x04
 107 #define DMA_ADDR_3              0x06
 108 #define DMA_ADDR_4              0xC0
 109 #define DMA_ADDR_5              0xC4
 110 #define DMA_ADDR_6              0xC8
 111 #define DMA_ADDR_7              0xCC
 112
 113 #define DMA_CNT_0               0x01    /* DMA count registers */
 114 #define DMA_CNT_1               0x03
 115 #define DMA_CNT_2               0x05
 116 #define DMA_CNT_3               0x07
 117 #define DMA_CNT_4               0xC2
 118 #define DMA_CNT_5               0xC6
 119 #define DMA_CNT_6               0xCA
 120 #define DMA_CNT_7               0xCE
 121
 122 #define DMA_PAGE_0              0x87    /* DMA page registers */
 123 #define DMA_PAGE_1              0x83
 124 #define DMA_PAGE_2              0x81
 125 #define DMA_PAGE_3              0x82
 126 #define DMA_PAGE_5              0x8B
 127 #define DMA_PAGE_6              0x89
 128 #define DMA_PAGE_7              0x8A
 129
 130 #define DMA_MODE_READ   0x44    /* I/O to memory, no autoinit, increment, single mode */
 131 #define DMA_MODE_WRITE  0x48    /* memory to I/O, no autoinit, increment, single mode */
 132 #define DMA_MODE_CASCADE 0xC0   /* pass thru DREQ->HRQ, DACK<-HLDA only */
 133
 134 #define DMA_AUTOINIT    0x10
 135
 136
 137 extern spinlock_t  dma_spin_lock;
 138
 139 static __inline__ unsigned long claim_dma_lock(void)
 140 {
 141         unsigned long flags;
 142         spin_lock_irqsave(&dma_spin_lock, flags);
 143         return flags;
 144 }
 145
 146 static __inline__ void release_dma_lock(unsigned long flags)
 147 {
 148         spin_unlock_irqrestore(&dma_spin_lock, flags);
 149 }
 150
 151 /* enable/disable a specific DMA channel */
 152 static __inline__ void enable_dma(unsigned int dmanr)
 153 {
 154         if (dmanr<=3)
 155                 dma_outb(dmanr,  DMA1_MASK_REG);
 156         else
 157                 dma_outb(dmanr & 3,  DMA2_MASK_REG);
 158 }
 159
 160 static __inline__ void disable_dma(unsigned int dmanr)
 161 {
 162         if (dmanr<=3)
 163                 dma_outb(dmanr | 4,  DMA1_MASK_REG);
 164         else
 165                 dma_outb((dmanr & 3) | 4,  DMA2_MASK_REG);
 166 }
 167
 168 /* Clear the 'DMA Pointer Flip Flop'.
 169  * Write 0 for LSB/MSB, 1 for MSB/LSB access.
 170  * Use this once to initialize the FF to a known state.
 171  * After that, keep track of it. :-)
 172  * --- In order to do that, the DMA routines below should ---
 173  * --- only be used while holding the DMA lock ! ---
 174  */
 175 static __inline__ void clear_dma_ff(unsigned int dmanr)
 176 {
 177         if (dmanr<=3)
 178                 dma_outb(0,  DMA1_CLEAR_FF_REG);
 179         else
 180                 dma_outb(0,  DMA2_CLEAR_FF_REG);
 181 }
 182
 183 /* set mode (above) for a specific DMA channel */
 184 static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
 185 {
 186         if (dmanr<=3)
 187                 dma_outb(mode | dmanr,  DMA1_MODE_REG);
 188         else
 189                 dma_outb(mode | (dmanr&3),  DMA2_MODE_REG);
 190 }
 191
 192 /* Set only the page register bits of the transfer address.
 193  * This is used for successive transfers when we know the contents of
 194  * the lower 16 bits of the DMA current address register, but a 64k boundary
 195  * may have been crossed.
 196  */
 197 static __inline__ void set_dma_page(unsigned int dmanr, unsigned int pagenr)
 198 {
 199         switch(dmanr) {
 200                 case 0:
 201                         dma_outb( pagenr       & 0xff, DMA_PAGE_0);
 202                         dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_0 + 0x400);
 203                         break;
 204                 case 1:
 205                         dma_outb( pagenr       & 0xff, DMA_PAGE_1);
 206                         dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_1 + 0x400);
 207                         break;
 208                 case 2:
 209                         dma_outb( pagenr       & 0xff, DMA_PAGE_2);
 210                         dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_2 + 0x400);
 211                         break;
 212                 case 3:
 213                         dma_outb( pagenr       & 0xff, DMA_PAGE_3);
 214                         dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_3 + 0x400);
 215                         break;
 216                 case 5:
 217                         dma_outb( pagenr       & 0xfe, DMA_PAGE_5);
 218                         dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_5 + 0x400);
 219                         break;
 220                 case 6:
 221                         dma_outb( pagenr       & 0xfe, DMA_PAGE_6);
 222                         dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_6 + 0x400);
 223                         break;
 224                 case 7:
 225                         dma_outb( pagenr       & 0xfe, DMA_PAGE_7);
 226                         dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_7 + 0x400);
 227                         break;
 228         }
 229 }
 230
 231
 232 /* Set transfer address & page bits for specific DMA channel.
 233  * Assumes dma flipflop is clear.
 234  */
 235 static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
 236 {
 237         set_dma_page(dmanr, a>>16);
 238         if (dmanr <= 3)  {
 239             dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
 240             dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
 241         }  else  {
 242             dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
 243             dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
 244         }
 245 }
 246
 247
 248 /* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
 249  * a specific DMA channel.
 250  * You must ensure the parameters are valid.
 251  * NOTE: from a manual: "the number of transfers is one more
 252  * than the initial word count"! This is taken into account.
 253  * Assumes dma flip-flop is clear.
 254  * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
 255  */
 256 static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
 257 {
 258         count--;
 259         if (dmanr <= 3)  {
 260             dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
 261             dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
 262         } else {
 263             dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
 264             dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
 265         }
 266 }
 267
 268
 269 /* Get DMA residue count. After a DMA transfer, this
 270  * should return zero. Reading this while a DMA transfer is
 271  * still in progress will return unpredictable results.
 272  * If called before the channel has been used, it may return 1.
 273  * Otherwise, it returns the number of _bytes_ left to transfer.
 274  *
 275  * Assumes DMA flip-flop is clear.
 276  */
 277 static __inline__ int get_dma_residue(unsigned int dmanr)
 278 {
 279         unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
 280                                          : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
 281
 282         /* using short to get 16-bit wrap around */
 283         unsigned short count;
 284
 285         count = 1 + dma_inb(io_port);
 286         count += dma_inb(io_port) << 8;
 287         return (dmanr<=3)? count : (count<<1);
 288 }
 289
 290
 291 /* These are in kernel/dma.c: */
 292 extern int request_dma(unsigned int dmanr, const char * device_id);     /* reserve a DMA channel */
 293 extern void free_dma(unsigned int dmanr);       /* release it again */
 294
 295 /* From PCI */
 296
 297 #ifdef CONFIG_PCI
 298 extern int isa_dma_bridge_buggy;
 299 #else
 300 #define isa_dma_bridge_buggy    (0)
 301 #endif
 302
 303 #endif /* _ASM_MPC1211_DMA_H */