drivers/tty/serial/ip22zilog.h

   1 #ifndef _IP22_ZILOG_H
   2 #define _IP22_ZILOG_H
   3
   4 #include <asm/byteorder.h>
   5
   6 struct zilog_channel {
   7 #ifdef __BIG_ENDIAN
   8         volatile unsigned char unused0[3];
   9         volatile unsigned char control;
  10         volatile unsigned char unused1[3];
  11         volatile unsigned char data;
  12 #else /* __LITTLE_ENDIAN */
  13         volatile unsigned char control;
  14         volatile unsigned char unused0[3];
  15         volatile unsigned char data;
  16         volatile unsigned char unused1[3];
  17 #endif
  18 };
  19
  20 struct zilog_layout {
  21         struct zilog_channel channelB;
  22         struct zilog_channel channelA;
  23 };
  24
  25 #define NUM_ZSREGS    16
  26
  27 /* Conversion routines to/from brg time constants from/to bits
  28  * per second.
  29  */
  30 #define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
  31 #define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
  32
  33 /* The Zilog register set */
  34
  35 #define FLAG    0x7e
  36
  37 /* Write Register 0 */
  38 #define R0      0               /* Register selects */
  39 #define R1      1
  40 #define R2      2
  41 #define R3      3
  42 #define R4      4
  43 #define R5      5
  44 #define R6      6
  45 #define R7      7
  46 #define R8      8
  47 #define R9      9
  48 #define R10     10
  49 #define R11     11
  50 #define R12     12
  51 #define R13     13
  52 #define R14     14
  53 #define R15     15
  54
  55 #define NULLCODE        0       /* Null Code */
  56 #define POINT_HIGH      0x8     /* Select upper half of registers */
  57 #define RES_EXT_INT     0x10    /* Reset Ext. Status Interrupts */
  58 #define SEND_ABORT      0x18    /* HDLC Abort */
  59 #define RES_RxINT_FC    0x20    /* Reset RxINT on First Character */
  60 #define RES_Tx_P        0x28    /* Reset TxINT Pending */
  61 #define ERR_RES         0x30    /* Error Reset */
  62 #define RES_H_IUS       0x38    /* Reset highest IUS */
  63
  64 #define RES_Rx_CRC      0x40    /* Reset Rx CRC Checker */
  65 #define RES_Tx_CRC      0x80    /* Reset Tx CRC Checker */
  66 #define RES_EOM_L       0xC0    /* Reset EOM latch */
  67
  68 /* Write Register 1 */
  69
  70 #define EXT_INT_ENAB    0x1     /* Ext Int Enable */
  71 #define TxINT_ENAB      0x2     /* Tx Int Enable */
  72 #define PAR_SPEC        0x4     /* Parity is special condition */
  73
  74 #define RxINT_DISAB     0       /* Rx Int Disable */
  75 #define RxINT_FCERR     0x8     /* Rx Int on First Character Only or Error */
  76 #define INT_ALL_Rx      0x10    /* Int on all Rx Characters or error */
  77 #define INT_ERR_Rx      0x18    /* Int on error only */
  78 #define RxINT_MASK      0x18
  79
  80 #define WT_RDY_RT       0x20    /* Wait/Ready on R/T */
  81 #define WT_FN_RDYFN     0x40    /* Wait/FN/Ready FN */
  82 #define WT_RDY_ENAB     0x80    /* Wait/Ready Enable */
  83
  84 /* Write Register #2 (Interrupt Vector) */
  85
  86 /* Write Register 3 */
  87
  88 #define RxENAB          0x1     /* Rx Enable */
  89 #define SYNC_L_INH      0x2     /* Sync Character Load Inhibit */
  90 #define ADD_SM          0x4     /* Address Search Mode (SDLC) */
  91 #define RxCRC_ENAB      0x8     /* Rx CRC Enable */
  92 #define ENT_HM          0x10    /* Enter Hunt Mode */
  93 #define AUTO_ENAB       0x20    /* Auto Enables */
  94 #define Rx5             0x0     /* Rx 5 Bits/Character */
  95 #define Rx7             0x40    /* Rx 7 Bits/Character */
  96 #define Rx6             0x80    /* Rx 6 Bits/Character */
  97 #define Rx8             0xc0    /* Rx 8 Bits/Character */
  98 #define RxN_MASK        0xc0
  99
 100 /* Write Register 4 */
 101
 102 #define PAR_ENAB        0x1     /* Parity Enable */
 103 #define PAR_EVEN        0x2     /* Parity Even/Odd* */
 104
 105 #define SYNC_ENAB       0       /* Sync Modes Enable */
 106 #define SB1             0x4     /* 1 stop bit/char */
 107 #define SB15            0x8     /* 1.5 stop bits/char */
 108 #define SB2             0xc     /* 2 stop bits/char */
 109
 110 #define MONSYNC         0       /* 8 Bit Sync character */
 111 #define BISYNC          0x10    /* 16 bit sync character */
 112 #define SDLC            0x20    /* SDLC Mode (01111110 Sync Flag) */
 113 #define EXTSYNC         0x30    /* External Sync Mode */
 114
 115 #define X1CLK           0x0     /* x1 clock mode */
 116 #define X16CLK          0x40    /* x16 clock mode */
 117 #define X32CLK          0x80    /* x32 clock mode */
 118 #define X64CLK          0xC0    /* x64 clock mode */
 119 #define XCLK_MASK       0xC0
 120
 121 /* Write Register 5 */
 122
 123 #define TxCRC_ENAB      0x1     /* Tx CRC Enable */
 124 #define RTS             0x2     /* RTS */
 125 #define SDLC_CRC        0x4     /* SDLC/CRC-16 */
 126 #define TxENAB          0x8     /* Tx Enable */
 127 #define SND_BRK         0x10    /* Send Break */
 128 #define Tx5             0x0     /* Tx 5 bits (or less)/character */
 129 #define Tx7             0x20    /* Tx 7 bits/character */
 130 #define Tx6             0x40    /* Tx 6 bits/character */
 131 #define Tx8             0x60    /* Tx 8 bits/character */
 132 #define TxN_MASK        0x60
 133 #define DTR             0x80    /* DTR */
 134
 135 /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
 136
 137 /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
 138
 139 /* Write Register 8 (transmit buffer) */
 140
 141 /* Write Register 9 (Master interrupt control) */
 142 #define VIS     1       /* Vector Includes Status */
 143 #define NV      2       /* No Vector */
 144 #define DLC     4       /* Disable Lower Chain */
 145 #define MIE     8       /* Master Interrupt Enable */
 146 #define STATHI  0x10    /* Status high */
 147 #define NORESET 0       /* No reset on write to R9 */
 148 #define CHRB    0x40    /* Reset channel B */
 149 #define CHRA    0x80    /* Reset channel A */
 150 #define FHWRES  0xc0    /* Force hardware reset */
 151
 152 /* Write Register 10 (misc control bits) */
 153 #define BIT6    1       /* 6 bit/8bit sync */
 154 #define LOOPMODE 2      /* SDLC Loop mode */
 155 #define ABUNDER 4       /* Abort/flag on SDLC xmit underrun */
 156 #define MARKIDLE 8      /* Mark/flag on idle */
 157 #define GAOP    0x10    /* Go active on poll */
 158 #define NRZ     0       /* NRZ mode */
 159 #define NRZI    0x20    /* NRZI mode */
 160 #define FM1     0x40    /* FM1 (transition = 1) */
 161 #define FM0     0x60    /* FM0 (transition = 0) */
 162 #define CRCPS   0x80    /* CRC Preset I/O */
 163
 164 /* Write Register 11 (Clock Mode control) */
 165 #define TRxCXT  0       /* TRxC = Xtal output */
 166 #define TRxCTC  1       /* TRxC = Transmit clock */
 167 #define TRxCBR  2       /* TRxC = BR Generator Output */
 168 #define TRxCDP  3       /* TRxC = DPLL output */
 169 #define TRxCOI  4       /* TRxC O/I */
 170 #define TCRTxCP 0       /* Transmit clock = RTxC pin */
 171 #define TCTRxCP 8       /* Transmit clock = TRxC pin */
 172 #define TCBR    0x10    /* Transmit clock = BR Generator output */
 173 #define TCDPLL  0x18    /* Transmit clock = DPLL output */
 174 #define RCRTxCP 0       /* Receive clock = RTxC pin */
 175 #define RCTRxCP 0x20    /* Receive clock = TRxC pin */
 176 #define RCBR    0x40    /* Receive clock = BR Generator output */
 177 #define RCDPLL  0x60    /* Receive clock = DPLL output */
 178 #define RTxCX   0x80    /* RTxC Xtal/No Xtal */
 179
 180 /* Write Register 12 (lower byte of baud rate generator time constant) */
 181
 182 /* Write Register 13 (upper byte of baud rate generator time constant) */
 183
 184 /* Write Register 14 (Misc control bits) */
 185 #define BRENAB  1       /* Baud rate generator enable */
 186 #define BRSRC   2       /* Baud rate generator source */
 187 #define DTRREQ  4       /* DTR/Request function */
 188 #define AUTOECHO 8      /* Auto Echo */
 189 #define LOOPBAK 0x10    /* Local loopback */
 190 #define SEARCH  0x20    /* Enter search mode */
 191 #define RMC     0x40    /* Reset missing clock */
 192 #define DISDPLL 0x60    /* Disable DPLL */
 193 #define SSBR    0x80    /* Set DPLL source = BR generator */
 194 #define SSRTxC  0xa0    /* Set DPLL source = RTxC */
 195 #define SFMM    0xc0    /* Set FM mode */
 196 #define SNRZI   0xe0    /* Set NRZI mode */
 197
 198 /* Write Register 15 (external/status interrupt control) */
 199 #define ZCIE    2       /* Zero count IE */
 200 #define DCDIE   8       /* DCD IE */
 201 #define SYNCIE  0x10    /* Sync/hunt IE */
 202 #define CTSIE   0x20    /* CTS IE */
 203 #define TxUIE   0x40    /* Tx Underrun/EOM IE */
 204 #define BRKIE   0x80    /* Break/Abort IE */
 205
 206
 207 /* Read Register 0 */
 208 #define Rx_CH_AV        0x1     /* Rx Character Available */
 209 #define ZCOUNT          0x2     /* Zero count */
 210 #define Tx_BUF_EMP      0x4     /* Tx Buffer empty */
 211 #define DCD             0x8     /* DCD */
 212 #define SYNC            0x10    /* Sync/hunt */
 213 #define CTS             0x20    /* CTS */
 214 #define TxEOM           0x40    /* Tx underrun */
 215 #define BRK_ABRT        0x80    /* Break/Abort */
 216
 217 /* Read Register 1 */
 218 #define ALL_SNT         0x1     /* All sent */
 219 /* Residue Data for 8 Rx bits/char programmed */
 220 #define RES3            0x8     /* 0/3 */
 221 #define RES4            0x4     /* 0/4 */
 222 #define RES5            0xc     /* 0/5 */
 223 #define RES6            0x2     /* 0/6 */
 224 #define RES7            0xa     /* 0/7 */
 225 #define RES8            0x6     /* 0/8 */
 226 #define RES18           0xe     /* 1/8 */
 227 #define RES28           0x0     /* 2/8 */
 228 /* Special Rx Condition Interrupts */
 229 #define PAR_ERR         0x10    /* Parity error */
 230 #define Rx_OVR          0x20    /* Rx Overrun Error */
 231 #define CRC_ERR         0x40    /* CRC/Framing Error */
 232 #define END_FR          0x80    /* End of Frame (SDLC) */
 233
 234 /* Read Register 2 (channel b only) - Interrupt vector */
 235 #define CHB_Tx_EMPTY    0x00
 236 #define CHB_EXT_STAT    0x02
 237 #define CHB_Rx_AVAIL    0x04
 238 #define CHB_SPECIAL     0x06
 239 #define CHA_Tx_EMPTY    0x08
 240 #define CHA_EXT_STAT    0x0a
 241 #define CHA_Rx_AVAIL    0x0c
 242 #define CHA_SPECIAL     0x0e
 243 #define STATUS_MASK     0x0e
 244
 245 /* Read Register 3 (interrupt pending register) ch a only */
 246 #define CHBEXT  0x1             /* Channel B Ext/Stat IP */
 247 #define CHBTxIP 0x2             /* Channel B Tx IP */
 248 #define CHBRxIP 0x4             /* Channel B Rx IP */
 249 #define CHAEXT  0x8             /* Channel A Ext/Stat IP */
 250 #define CHATxIP 0x10            /* Channel A Tx IP */
 251 #define CHARxIP 0x20            /* Channel A Rx IP */
 252
 253 /* Read Register 8 (receive data register) */
 254
 255 /* Read Register 10  (misc status bits) */
 256 #define ONLOOP  2               /* On loop */
 257 #define LOOPSEND 0x10           /* Loop sending */
 258 #define CLK2MIS 0x40            /* Two clocks missing */
 259 #define CLK1MIS 0x80            /* One clock missing */
 260
 261 /* Read Register 12 (lower byte of baud rate generator constant) */
 262
 263 /* Read Register 13 (upper byte of baud rate generator constant) */
 264
 265 /* Read Register 15 (value of WR 15) */
 266
 267 /* Misc macros */
 268 #define ZS_CLEARERR(channel)    do { writeb(ERR_RES, &channel->control); \
 269                                      udelay(5); } while(0)
 270
 271 #define ZS_CLEARSTAT(channel)   do { writeb(RES_EXT_INT, &channel->control); \
 272                                      udelay(5); } while(0)
 273
 274 #define ZS_CLEARFIFO(channel)   do { readb(&channel->data); \
 275                                      udelay(2); \
 276                                      readb(&channel->data); \
 277                                      udelay(2); \
 278                                      readb(&channel->data); \
 279                                      udelay(2); } while(0)
 280
 281 #endif /* _IP22_ZILOG_H */