arch/arm/mach-imx/mach-mx51_babbage.c

   1 /*
   2  * Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
   3  * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
   4  *
   5  * The code contained herein is licensed under the GNU General Public
   6  * License. You may obtain a copy of the GNU General Public License
   7  * Version 2 or later at the following locations:
   8  *
   9  * http://www.opensource.org/licenses/gpl-license.html
  10  * http://www.gnu.org/copyleft/gpl.html
  11  */
  12
  13 #include <linux/init.h>
  14 #include <linux/platform_device.h>
  15 #include <linux/i2c.h>
  16 #include <linux/gpio.h>
  17 #include <linux/delay.h>
  18 #include <linux/io.h>
  19 #include <linux/input.h>
  20 #include <linux/spi/flash.h>
  21 #include <linux/spi/spi.h>
  22
  23 #include <mach/common.h>
  24 #include <mach/hardware.h>
  25 #include <mach/iomux-mx51.h>
  26
  27 #include <asm/setup.h>
  28 #include <asm/mach-types.h>
  29 #include <asm/mach/arch.h>
  30 #include <asm/mach/time.h>
  31
  32 #include "devices-imx51.h"
  33 #include "cpu_op-mx51.h"
  34
  35 #define BABBAGE_USB_HUB_RESET   IMX_GPIO_NR(1, 7)
  36 #define BABBAGE_USBH1_STP       IMX_GPIO_NR(1, 27)
  37 #define BABBAGE_USB_PHY_RESET   IMX_GPIO_NR(2, 5)
  38 #define BABBAGE_FEC_PHY_RESET   IMX_GPIO_NR(2, 14)
  39 #define BABBAGE_POWER_KEY       IMX_GPIO_NR(2, 21)
  40 #define BABBAGE_ECSPI1_CS0      IMX_GPIO_NR(4, 24)
  41 #define BABBAGE_ECSPI1_CS1      IMX_GPIO_NR(4, 25)
  42 #define BABBAGE_SD2_CD          IMX_GPIO_NR(1, 6)
  43 #define BABBAGE_SD2_WP          IMX_GPIO_NR(1, 5)
  44
  45 /* USB_CTRL_1 */
  46 #define MX51_USB_CTRL_1_OFFSET                  0x10
  47 #define MX51_USB_CTRL_UH1_EXT_CLK_EN            (1 << 25)
  48
  49 #define MX51_USB_PLLDIV_12_MHZ          0x00
  50 #define MX51_USB_PLL_DIV_19_2_MHZ       0x01
  51 #define MX51_USB_PLL_DIV_24_MHZ 0x02
  52
  53 static struct gpio_keys_button babbage_buttons[] = {
  54         {
  55                 .gpio           = BABBAGE_POWER_KEY,
  56                 .code           = BTN_0,
  57                 .desc           = "PWR",
  58                 .active_low     = 1,
  59                 .wakeup         = 1,
  60         },
  61 };
  62
  63 static const struct gpio_keys_platform_data imx_button_data __initconst = {
  64         .buttons        = babbage_buttons,
  65         .nbuttons       = ARRAY_SIZE(babbage_buttons),
  66 };
  67
  68 static iomux_v3_cfg_t mx51babbage_pads[] = {
  69         /* UART1 */
  70         MX51_PAD_UART1_RXD__UART1_RXD,
  71         MX51_PAD_UART1_TXD__UART1_TXD,
  72         MX51_PAD_UART1_RTS__UART1_RTS,
  73         MX51_PAD_UART1_CTS__UART1_CTS,
  74
  75         /* UART2 */
  76         MX51_PAD_UART2_RXD__UART2_RXD,
  77         MX51_PAD_UART2_TXD__UART2_TXD,
  78
  79         /* UART3 */
  80         MX51_PAD_EIM_D25__UART3_RXD,
  81         MX51_PAD_EIM_D26__UART3_TXD,
  82         MX51_PAD_EIM_D27__UART3_RTS,
  83         MX51_PAD_EIM_D24__UART3_CTS,
  84
  85         /* I2C1 */
  86         MX51_PAD_EIM_D16__I2C1_SDA,
  87         MX51_PAD_EIM_D19__I2C1_SCL,
  88
  89         /* I2C2 */
  90         MX51_PAD_KEY_COL4__I2C2_SCL,
  91         MX51_PAD_KEY_COL5__I2C2_SDA,
  92
  93         /* HSI2C */
  94         MX51_PAD_I2C1_CLK__I2C1_CLK,
  95         MX51_PAD_I2C1_DAT__I2C1_DAT,
  96
  97         /* USB HOST1 */
  98         MX51_PAD_USBH1_CLK__USBH1_CLK,
  99         MX51_PAD_USBH1_DIR__USBH1_DIR,
 100         MX51_PAD_USBH1_NXT__USBH1_NXT,
 101         MX51_PAD_USBH1_DATA0__USBH1_DATA0,
 102         MX51_PAD_USBH1_DATA1__USBH1_DATA1,
 103         MX51_PAD_USBH1_DATA2__USBH1_DATA2,
 104         MX51_PAD_USBH1_DATA3__USBH1_DATA3,
 105         MX51_PAD_USBH1_DATA4__USBH1_DATA4,
 106         MX51_PAD_USBH1_DATA5__USBH1_DATA5,
 107         MX51_PAD_USBH1_DATA6__USBH1_DATA6,
 108         MX51_PAD_USBH1_DATA7__USBH1_DATA7,
 109
 110         /* USB HUB reset line*/
 111         MX51_PAD_GPIO1_7__GPIO1_7,
 112
 113         /* USB PHY reset line */
 114         MX51_PAD_EIM_D21__GPIO2_5,
 115
 116         /* FEC */
 117         MX51_PAD_EIM_EB2__FEC_MDIO,
 118         MX51_PAD_EIM_EB3__FEC_RDATA1,
 119         MX51_PAD_EIM_CS2__FEC_RDATA2,
 120         MX51_PAD_EIM_CS3__FEC_RDATA3,
 121         MX51_PAD_EIM_CS4__FEC_RX_ER,
 122         MX51_PAD_EIM_CS5__FEC_CRS,
 123         MX51_PAD_NANDF_RB2__FEC_COL,
 124         MX51_PAD_NANDF_RB3__FEC_RX_CLK,
 125         MX51_PAD_NANDF_D9__FEC_RDATA0,
 126         MX51_PAD_NANDF_D8__FEC_TDATA0,
 127         MX51_PAD_NANDF_CS2__FEC_TX_ER,
 128         MX51_PAD_NANDF_CS3__FEC_MDC,
 129         MX51_PAD_NANDF_CS4__FEC_TDATA1,
 130         MX51_PAD_NANDF_CS5__FEC_TDATA2,
 131         MX51_PAD_NANDF_CS6__FEC_TDATA3,
 132         MX51_PAD_NANDF_CS7__FEC_TX_EN,
 133         MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK,
 134
 135         /* FEC PHY reset line */
 136         MX51_PAD_EIM_A20__GPIO2_14,
 137
 138         /* SD 1 */
 139         MX51_PAD_SD1_CMD__SD1_CMD,
 140         MX51_PAD_SD1_CLK__SD1_CLK,
 141         MX51_PAD_SD1_DATA0__SD1_DATA0,
 142         MX51_PAD_SD1_DATA1__SD1_DATA1,
 143         MX51_PAD_SD1_DATA2__SD1_DATA2,
 144         MX51_PAD_SD1_DATA3__SD1_DATA3,
 145         /* CD/WP from controller */
 146         MX51_PAD_GPIO1_0__SD1_CD,
 147         MX51_PAD_GPIO1_1__SD1_WP,
 148
 149         /* SD 2 */
 150         MX51_PAD_SD2_CMD__SD2_CMD,
 151         MX51_PAD_SD2_CLK__SD2_CLK,
 152         MX51_PAD_SD2_DATA0__SD2_DATA0,
 153         MX51_PAD_SD2_DATA1__SD2_DATA1,
 154         MX51_PAD_SD2_DATA2__SD2_DATA2,
 155         MX51_PAD_SD2_DATA3__SD2_DATA3,
 156         /* CD/WP gpio */
 157         MX51_PAD_GPIO1_6__GPIO1_6,
 158         MX51_PAD_GPIO1_5__GPIO1_5,
 159
 160         /* eCSPI1 */
 161         MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
 162         MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
 163         MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
 164         MX51_PAD_CSPI1_SS0__GPIO4_24,
 165         MX51_PAD_CSPI1_SS1__GPIO4_25,
 166 };
 167
 168 /* Serial ports */
 169 static const struct imxuart_platform_data uart_pdata __initconst = {
 170         .flags = IMXUART_HAVE_RTSCTS,
 171 };
 172
 173 static const struct imxi2c_platform_data babbage_i2c_data __initconst = {
 174         .bitrate = 100000,
 175 };
 176
 177 static const struct imxi2c_platform_data babbage_hsi2c_data __initconst = {
 178         .bitrate = 400000,
 179 };
 180
 181 static struct gpio mx51_babbage_usbh1_gpios[] = {
 182         { BABBAGE_USBH1_STP, GPIOF_OUT_INIT_LOW, "usbh1_stp" },
 183         { BABBAGE_USB_PHY_RESET, GPIOF_OUT_INIT_LOW, "usbh1_phy_reset" },
 184 };
 185
 186 static int gpio_usbh1_active(void)
 187 {
 188         iomux_v3_cfg_t usbh1stp_gpio = MX51_PAD_USBH1_STP__GPIO1_27;
 189         int ret;
 190
 191         /* Set USBH1_STP to GPIO and toggle it */
 192         mxc_iomux_v3_setup_pad(usbh1stp_gpio);
 193         ret = gpio_request_array(mx51_babbage_usbh1_gpios,
 194                                         ARRAY_SIZE(mx51_babbage_usbh1_gpios));
 195
 196         if (ret) {
 197                 pr_debug("failed to get USBH1 pins: %d\n", ret);
 198                 return ret;
 199         }
 200
 201         msleep(100);
 202         gpio_set_value(BABBAGE_USBH1_STP, 1);
 203         gpio_set_value(BABBAGE_USB_PHY_RESET, 1);
 204         gpio_free_array(mx51_babbage_usbh1_gpios,
 205                                         ARRAY_SIZE(mx51_babbage_usbh1_gpios));
 206         return 0;
 207 }
 208
 209 static inline void babbage_usbhub_reset(void)
 210 {
 211         int ret;
 212
 213         /* Reset USB hub */
 214         ret = gpio_request_one(BABBAGE_USB_HUB_RESET,
 215                                         GPIOF_OUT_INIT_LOW, "GPIO1_7");
 216         if (ret) {
 217                 printk(KERN_ERR"failed to get GPIO_USB_HUB_RESET: %d\n", ret);
 218                 return;
 219         }
 220
 221         msleep(2);
 222         /* Deassert reset */
 223         gpio_set_value(BABBAGE_USB_HUB_RESET, 1);
 224 }
 225
 226 static inline void babbage_fec_reset(void)
 227 {
 228         int ret;
 229
 230         /* reset FEC PHY */
 231         ret = gpio_request_one(BABBAGE_FEC_PHY_RESET,
 232                                         GPIOF_OUT_INIT_LOW, "fec-phy-reset");
 233         if (ret) {
 234                 printk(KERN_ERR"failed to get GPIO_FEC_PHY_RESET: %d\n", ret);
 235                 return;
 236         }
 237         msleep(1);
 238         gpio_set_value(BABBAGE_FEC_PHY_RESET, 1);
 239 }
 240
 241 /* This function is board specific as the bit mask for the plldiv will also
 242 be different for other Freescale SoCs, thus a common bitmask is not
 243 possible and cannot get place in /plat-mxc/ehci.c.*/
 244 static int initialize_otg_port(struct platform_device *pdev)
 245 {
 246         u32 v;
 247         void __iomem *usb_base;
 248         void __iomem *usbother_base;
 249
 250         usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
 251         if (!usb_base)
 252                 return -ENOMEM;
 253         usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
 254
 255         /* Set the PHY clock to 19.2MHz */
 256         v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
 257         v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
 258         v |= MX51_USB_PLL_DIV_19_2_MHZ;
 259         __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
 260         iounmap(usb_base);
 261
 262         mdelay(10);
 263
 264         return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
 265 }
 266
 267 static int initialize_usbh1_port(struct platform_device *pdev)
 268 {
 269         u32 v;
 270         void __iomem *usb_base;
 271         void __iomem *usbother_base;
 272
 273         usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
 274         if (!usb_base)
 275                 return -ENOMEM;
 276         usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
 277
 278         /* The clock for the USBH1 ULPI port will come externally from the PHY. */
 279         v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
 280         __raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN, usbother_base + MX51_USB_CTRL_1_OFFSET);
 281         iounmap(usb_base);
 282
 283         mdelay(10);
 284
 285         return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
 286                         MXC_EHCI_ITC_NO_THRESHOLD);
 287 }
 288
 289 static const struct mxc_usbh_platform_data dr_utmi_config __initconst = {
 290         .init           = initialize_otg_port,
 291         .portsc = MXC_EHCI_UTMI_16BIT,
 292 };
 293
 294 static const struct fsl_usb2_platform_data usb_pdata __initconst = {
 295         .operating_mode = FSL_USB2_DR_DEVICE,
 296         .phy_mode       = FSL_USB2_PHY_UTMI_WIDE,
 297 };
 298
 299 static const struct mxc_usbh_platform_data usbh1_config __initconst = {
 300         .init           = initialize_usbh1_port,
 301         .portsc = MXC_EHCI_MODE_ULPI,
 302 };
 303
 304 static int otg_mode_host;
 305
 306 static int __init babbage_otg_mode(char *options)
 307 {
 308         if (!strcmp(options, "host"))
 309                 otg_mode_host = 1;
 310         else if (!strcmp(options, "device"))
 311                 otg_mode_host = 0;
 312         else
 313                 pr_info("otg_mode neither \"host\" nor \"device\". "
 314                         "Defaulting to device\n");
 315         return 0;
 316 }
 317 __setup("otg_mode=", babbage_otg_mode);
 318
 319 static struct spi_board_info mx51_babbage_spi_board_info[] __initdata = {
 320         {
 321                 .modalias = "mtd_dataflash",
 322                 .max_speed_hz = 25000000,
 323                 .bus_num = 0,
 324                 .chip_select = 1,
 325                 .mode = SPI_MODE_0,
 326                 .platform_data = NULL,
 327         },
 328 };
 329
 330 static int mx51_babbage_spi_cs[] = {
 331         BABBAGE_ECSPI1_CS0,
 332         BABBAGE_ECSPI1_CS1,
 333 };
 334
 335 static const struct spi_imx_master mx51_babbage_spi_pdata __initconst = {
 336         .chipselect     = mx51_babbage_spi_cs,
 337         .num_chipselect = ARRAY_SIZE(mx51_babbage_spi_cs),
 338 };
 339
 340 static const struct esdhc_platform_data mx51_babbage_sd1_data __initconst = {
 341         .cd_type = ESDHC_CD_CONTROLLER,
 342         .wp_type = ESDHC_WP_CONTROLLER,
 343 };
 344
 345 static const struct esdhc_platform_data mx51_babbage_sd2_data __initconst = {
 346         .cd_gpio = BABBAGE_SD2_CD,
 347         .wp_gpio = BABBAGE_SD2_WP,
 348         .cd_type = ESDHC_CD_GPIO,
 349         .wp_type = ESDHC_WP_GPIO,
 350 };
 351
 352 void __init imx51_babbage_common_init(void)
 353 {
 354         mxc_iomux_v3_setup_multiple_pads(mx51babbage_pads,
 355                                          ARRAY_SIZE(mx51babbage_pads));
 356 }
 357
 358 /*
 359  * Board specific initialization.
 360  */
 361 static void __init mx51_babbage_init(void)
 362 {
 363         iomux_v3_cfg_t usbh1stp = MX51_PAD_USBH1_STP__USBH1_STP;
 364         iomux_v3_cfg_t power_key = NEW_PAD_CTRL(MX51_PAD_EIM_A27__GPIO2_21,
 365                 PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH);
 366
 367         imx51_soc_init();
 368
 369 #if defined(CONFIG_CPU_FREQ_IMX)
 370         get_cpu_op = mx51_get_cpu_op;
 371 #endif
 372         imx51_babbage_common_init();
 373
 374         imx51_add_imx_uart(0, &uart_pdata);
 375         imx51_add_imx_uart(1, NULL);
 376         imx51_add_imx_uart(2, &uart_pdata);
 377
 378         babbage_fec_reset();
 379         imx51_add_fec(NULL);
 380
 381         /* Set the PAD settings for the pwr key. */
 382         mxc_iomux_v3_setup_pad(power_key);
 383         imx_add_gpio_keys(&imx_button_data);
 384
 385         imx51_add_imx_i2c(0, &babbage_i2c_data);
 386         imx51_add_imx_i2c(1, &babbage_i2c_data);
 387         imx51_add_hsi2c(&babbage_hsi2c_data);
 388
 389         if (otg_mode_host)
 390                 imx51_add_mxc_ehci_otg(&dr_utmi_config);
 391         else {
 392                 initialize_otg_port(NULL);
 393                 imx51_add_fsl_usb2_udc(&usb_pdata);
 394         }
 395
 396         gpio_usbh1_active();
 397         imx51_add_mxc_ehci_hs(1, &usbh1_config);
 398         /* setback USBH1_STP to be function */
 399         mxc_iomux_v3_setup_pad(usbh1stp);
 400         babbage_usbhub_reset();
 401
 402         imx51_add_sdhci_esdhc_imx(0, &mx51_babbage_sd1_data);
 403         imx51_add_sdhci_esdhc_imx(1, &mx51_babbage_sd2_data);
 404
 405         spi_register_board_info(mx51_babbage_spi_board_info,
 406                 ARRAY_SIZE(mx51_babbage_spi_board_info));
 407         imx51_add_ecspi(0, &mx51_babbage_spi_pdata);
 408         imx51_add_imx2_wdt(0, NULL);
 409 }
 410
 411 static void __init mx51_babbage_timer_init(void)
 412 {
 413         mx51_clocks_init(32768, 24000000, 22579200, 0);
 414 }
 415
 416 static struct sys_timer mx51_babbage_timer = {
 417         .init = mx51_babbage_timer_init,
 418 };
 419
 420 MACHINE_START(MX51_BABBAGE, "Freescale MX51 Babbage Board")
 421         /* Maintainer: Amit Kucheria <amit.kucheria@canonical.com> */
 422         .atag_offset = 0x100,
 423         .map_io = mx51_map_io,
 424         .init_early = imx51_init_early,
 425         .init_irq = mx51_init_irq,
 426         .handle_irq = imx51_handle_irq,
 427         .timer = &mx51_babbage_timer,
 428         .init_machine = mx51_babbage_init,
 429         .restart        = mxc_restart,
 430 MACHINE_END