spi-topcliff-pch: add recovery processing in case wait-event timeout

[zen-stable.git] / drivers / mtd / devices / docg3.c

/*
 * Handles the M-Systems DiskOnChip G3 chip
 *
 * Copyright (C) 2011 Robert Jarzmik
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 *
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/platform_device.h>
#include <linux/string.h>
#include <linux/slab.h>
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/bitmap.h>
#include <linux/bitrev.h>
#include <linux/bch.h>

#include <linux/debugfs.h>
#include <linux/seq_file.h>

#define CREATE_TRACE_POINTS
#include "docg3.h"

/*
 * This driver handles the DiskOnChip G3 flash memory.
 *
 * As no specification is available from M-Systems/Sandisk, this drivers lacks
 * several functions available on the chip, as :
 *  - IPL write
 *
 * The bus data width (8bits versus 16bits) is not handled (if_cfg flag), and
 * the driver assumes a 16bits data bus.
 *
 * DocG3 relies on 2 ECC algorithms, which are handled in hardware :
 *  - a 1 byte Hamming code stored in the OOB for each page
 *  - a 7 bytes BCH code stored in the OOB for each page
 * The BCH ECC is :
 *  - BCH is in GF(2^14)
 *  - BCH is over data of 520 bytes (512 page + 7 page_info bytes
 *                                   + 1 hamming byte)
 *  - BCH can correct up to 4 bits (t = 4)
 *  - BCH syndroms are calculated in hardware, and checked in hardware as well
 *
 */

static unsigned int reliable_mode;
module_param(reliable_mode, uint, 0);
MODULE_PARM_DESC(reliable_mode, "Set the docg3 mode (0=normal MLC, 1=fast, "
                 "2=reliable) : MLC normal operations are in normal mode");

/**
 * struct docg3_oobinfo - DiskOnChip G3 OOB layout
 * @eccbytes: 8 bytes are used (1 for Hamming ECC, 7 for BCH ECC)
 * @eccpos: ecc positions (byte 7 is Hamming ECC, byte 8-14 are BCH ECC)
 * @oobfree: free pageinfo bytes (byte 0 until byte 6, byte 15
 * @oobavail: 8 available bytes remaining after ECC toll
 */
static struct nand_ecclayout docg3_oobinfo = {
        .eccbytes = 8,
        .eccpos = {7, 8, 9, 10, 11, 12, 13, 14},
        .oobfree = {{0, 7}, {15, 1} },
        .oobavail = 8,
};

/**
 * struct docg3_bch - BCH engine
 */
static struct bch_control *docg3_bch;

static inline u8 doc_readb(struct docg3 *docg3, u16 reg)
{
        u8 val = readb(docg3->base + reg);

        trace_docg3_io(0, 8, reg, (int)val);
        return val;
}

static inline u16 doc_readw(struct docg3 *docg3, u16 reg)
{
        u16 val = readw(docg3->base + reg);

        trace_docg3_io(0, 16, reg, (int)val);
        return val;
}

static inline void doc_writeb(struct docg3 *docg3, u8 val, u16 reg)
{
        writeb(val, docg3->base + reg);
        trace_docg3_io(1, 8, reg, val);
}

static inline void doc_writew(struct docg3 *docg3, u16 val, u16 reg)
{
        writew(val, docg3->base + reg);
        trace_docg3_io(1, 16, reg, val);
}

static inline void doc_flash_command(struct docg3 *docg3, u8 cmd)
{
        doc_writeb(docg3, cmd, DOC_FLASHCOMMAND);
}

static inline void doc_flash_sequence(struct docg3 *docg3, u8 seq)
{
        doc_writeb(docg3, seq, DOC_FLASHSEQUENCE);
}

static inline void doc_flash_address(struct docg3 *docg3, u8 addr)
{
        doc_writeb(docg3, addr, DOC_FLASHADDRESS);
}

static char const *part_probes[] = { "cmdlinepart", "saftlpart", NULL };

static int doc_register_readb(struct docg3 *docg3, int reg)
{
        u8 val;

        doc_writew(docg3, reg, DOC_READADDRESS);
        val = doc_readb(docg3, reg);
        doc_vdbg("Read register %04x : %02x\n", reg, val);
        return val;
}

static int doc_register_readw(struct docg3 *docg3, int reg)
{
        u16 val;

        doc_writew(docg3, reg, DOC_READADDRESS);
        val = doc_readw(docg3, reg);
        doc_vdbg("Read register %04x : %04x\n", reg, val);
        return val;
}

/**
 * doc_delay - delay docg3 operations
 * @docg3: the device
 * @nbNOPs: the number of NOPs to issue
 *
 * As no specification is available, the right timings between chip commands are
 * unknown. The only available piece of information are the observed nops on a
 * working docg3 chip.
 * Therefore, doc_delay relies on a busy loop of NOPs, instead of scheduler
 * friendlier msleep() functions or blocking mdelay().
 */
static void doc_delay(struct docg3 *docg3, int nbNOPs)
{
        int i;

        doc_vdbg("NOP x %d\n", nbNOPs);
        for (i = 0; i < nbNOPs; i++)
                doc_writeb(docg3, 0, DOC_NOP);
}

static int is_prot_seq_error(struct docg3 *docg3)
{
        int ctrl;

        ctrl = doc_register_readb(docg3, DOC_FLASHCONTROL);
        return ctrl & (DOC_CTRL_PROTECTION_ERROR | DOC_CTRL_SEQUENCE_ERROR);
}

static int doc_is_ready(struct docg3 *docg3)
{
        int ctrl;

        ctrl = doc_register_readb(docg3, DOC_FLASHCONTROL);
        return ctrl & DOC_CTRL_FLASHREADY;
}

static int doc_wait_ready(struct docg3 *docg3)
{
        int maxWaitCycles = 100;

        do {
                doc_delay(docg3, 4);
                cpu_relax();
        } while (!doc_is_ready(docg3) && maxWaitCycles--);
        doc_delay(docg3, 2);
        if (maxWaitCycles > 0)
                return 0;
        else
                return -EIO;
}

static int doc_reset_seq(struct docg3 *docg3)
{
        int ret;

        doc_writeb(docg3, 0x10, DOC_FLASHCONTROL);
        doc_flash_sequence(docg3, DOC_SEQ_RESET);
        doc_flash_command(docg3, DOC_CMD_RESET);
        doc_delay(docg3, 2);
        ret = doc_wait_ready(docg3);

        doc_dbg("doc_reset_seq() -> isReady=%s\n", ret ? "false" : "true");
        return ret;
}

/**
 * doc_read_data_area - Read data from data area
 * @docg3: the device
 * @buf: the buffer to fill in (might be NULL is dummy reads)
 * @len: the length to read
 * @first: first time read, DOC_READADDRESS should be set
 *
 * Reads bytes from flash data. Handles the single byte / even bytes reads.
 */
static void doc_read_data_area(struct docg3 *docg3, void *buf, int len,
                               int first)
{
        int i, cdr, len4;
        u16 data16, *dst16;
        u8 data8, *dst8;

        doc_dbg("doc_read_data_area(buf=%p, len=%d)\n", buf, len);
        cdr = len & 0x3;
        len4 = len - cdr;

        if (first)
                doc_writew(docg3, DOC_IOSPACE_DATA, DOC_READADDRESS);
        dst16 = buf;
        for (i = 0; i < len4; i += 2) {
                data16 = doc_readw(docg3, DOC_IOSPACE_DATA);
                if (dst16) {
                        *dst16 = data16;
                        dst16++;
                }
        }

        if (cdr) {
                doc_writew(docg3, DOC_IOSPACE_DATA | DOC_READADDR_ONE_BYTE,
                           DOC_READADDRESS);
                doc_delay(docg3, 1);
                dst8 = (u8 *)dst16;
                for (i = 0; i < cdr; i++) {
                        data8 = doc_readb(docg3, DOC_IOSPACE_DATA);
                        if (dst8) {
                                *dst8 = data8;
                                dst8++;
                        }
                }
        }
}

/**
 * doc_write_data_area - Write data into data area
 * @docg3: the device
 * @buf: the buffer to get input bytes from
 * @len: the length to write
 *
 * Writes bytes into flash data. Handles the single byte / even bytes writes.
 */
static void doc_write_data_area(struct docg3 *docg3, const void *buf, int len)
{
        int i, cdr, len4;
        u16 *src16;
        u8 *src8;

        doc_dbg("doc_write_data_area(buf=%p, len=%d)\n", buf, len);
        cdr = len & 0x3;
        len4 = len - cdr;

        doc_writew(docg3, DOC_IOSPACE_DATA, DOC_READADDRESS);
        src16 = (u16 *)buf;
        for (i = 0; i < len4; i += 2) {
                doc_writew(docg3, *src16, DOC_IOSPACE_DATA);
                src16++;
        }

        src8 = (u8 *)src16;
        for (i = 0; i < cdr; i++) {
                doc_writew(docg3, DOC_IOSPACE_DATA | DOC_READADDR_ONE_BYTE,
                           DOC_READADDRESS);
                doc_writeb(docg3, *src8, DOC_IOSPACE_DATA);
                src8++;
        }
}

/**
 * doc_set_data_mode - Sets the flash to normal or reliable data mode
 * @docg3: the device
 *
 * The reliable data mode is a bit slower than the fast mode, but less errors
 * occur.  Entering the reliable mode cannot be done without entering the fast
 * mode first.
 *
 * In reliable mode, pages 2*n and 2*n+1 are clones. Writing to page 0 of blocks
 * (4,5) make the hardware write also to page 1 of blocks blocks(4,5). Reading
 * from page 0 of blocks (4,5) or from page 1 of blocks (4,5) gives the same
 * result, which is a logical and between bytes from page 0 and page 1 (which is
 * consistent with the fact that writing to a page is _clearing_ bits of that
 * page).
 */
static void doc_set_reliable_mode(struct docg3 *docg3)
{
        static char *strmode[] = { "normal", "fast", "reliable", "invalid" };

        doc_dbg("doc_set_reliable_mode(%s)\n", strmode[docg3->reliable]);
        switch (docg3->reliable) {
        case 0:
                break;
        case 1:
                doc_flash_sequence(docg3, DOC_SEQ_SET_FASTMODE);
                doc_flash_command(docg3, DOC_CMD_FAST_MODE);
                break;
        case 2:
                doc_flash_sequence(docg3, DOC_SEQ_SET_RELIABLEMODE);
                doc_flash_command(docg3, DOC_CMD_FAST_MODE);
                doc_flash_command(docg3, DOC_CMD_RELIABLE_MODE);
                break;
        default:
                doc_err("doc_set_reliable_mode(): invalid mode\n");
                break;
        }
        doc_delay(docg3, 2);
}

/**
 * doc_set_asic_mode - Set the ASIC mode
 * @docg3: the device
 * @mode: the mode
 *
 * The ASIC can work in 3 modes :
 *  - RESET: all registers are zeroed
 *  - NORMAL: receives and handles commands
 *  - POWERDOWN: minimal poweruse, flash parts shut off
 */
static void doc_set_asic_mode(struct docg3 *docg3, u8 mode)
{
        int i;

        for (i = 0; i < 12; i++)
                doc_readb(docg3, DOC_IOSPACE_IPL);

        mode |= DOC_ASICMODE_MDWREN;
        doc_dbg("doc_set_asic_mode(%02x)\n", mode);
        doc_writeb(docg3, mode, DOC_ASICMODE);
        doc_writeb(docg3, ~mode, DOC_ASICMODECONFIRM);
        doc_delay(docg3, 1);
}

/**
 * doc_set_device_id - Sets the devices id for cascaded G3 chips
 * @docg3: the device
 * @id: the chip to select (amongst 0, 1, 2, 3)
 *
 * There can be 4 cascaded G3 chips. This function selects the one which will
 * should be the active one.
 */
static void doc_set_device_id(struct docg3 *docg3, int id)
{
        u8 ctrl;

        doc_dbg("doc_set_device_id(%d)\n", id);
        doc_writeb(docg3, id, DOC_DEVICESELECT);
        ctrl = doc_register_readb(docg3, DOC_FLASHCONTROL);

        ctrl &= ~DOC_CTRL_VIOLATION;
        ctrl |= DOC_CTRL_CE;
        doc_writeb(docg3, ctrl, DOC_FLASHCONTROL);
}

/**
 * doc_set_extra_page_mode - Change flash page layout
 * @docg3: the device
 *
 * Normally, the flash page is split into the data (512 bytes) and the out of
 * band data (16 bytes). For each, 4 more bytes can be accessed, where the wear
 * leveling counters are stored.  To access this last area of 4 bytes, a special
 * mode must be input to the flash ASIC.
 *
 * Returns 0 if no error occured, -EIO else.
 */
static int doc_set_extra_page_mode(struct docg3 *docg3)
{
        int fctrl;

        doc_dbg("doc_set_extra_page_mode()\n");
        doc_flash_sequence(docg3, DOC_SEQ_PAGE_SIZE_532);
        doc_flash_command(docg3, DOC_CMD_PAGE_SIZE_532);
        doc_delay(docg3, 2);

        fctrl = doc_register_readb(docg3, DOC_FLASHCONTROL);
        if (fctrl & (DOC_CTRL_PROTECTION_ERROR | DOC_CTRL_SEQUENCE_ERROR))
                return -EIO;
        else
                return 0;
}

/**
 * doc_setup_addr_sector - Setup blocks/page/ofs address for one plane
 * @docg3: the device
 * @sector: the sector
 */
static void doc_setup_addr_sector(struct docg3 *docg3, int sector)
{
        doc_delay(docg3, 1);
        doc_flash_address(docg3, sector & 0xff);
        doc_flash_address(docg3, (sector >> 8) & 0xff);
        doc_flash_address(docg3, (sector >> 16) & 0xff);
        doc_delay(docg3, 1);
}

/**
 * doc_setup_writeaddr_sector - Setup blocks/page/ofs address for one plane
 * @docg3: the device
 * @sector: the sector
 * @ofs: the offset in the page, between 0 and (512 + 16 + 512)
 */
static void doc_setup_writeaddr_sector(struct docg3 *docg3, int sector, int ofs)
{
        ofs = ofs >> 2;
        doc_delay(docg3, 1);
        doc_flash_address(docg3, ofs & 0xff);
        doc_flash_address(docg3, sector & 0xff);
        doc_flash_address(docg3, (sector >> 8) & 0xff);
        doc_flash_address(docg3, (sector >> 16) & 0xff);
        doc_delay(docg3, 1);
}

/**
 * doc_seek - Set both flash planes to the specified block, page for reading
 * @docg3: the device
 * @block0: the first plane block index
 * @block1: the second plane block index
 * @page: the page index within the block
 * @wear: if true, read will occur on the 4 extra bytes of the wear area
 * @ofs: offset in page to read
 *
 * Programs the flash even and odd planes to the specific block and page.
 * Alternatively, programs the flash to the wear area of the specified page.
 */
static int doc_read_seek(struct docg3 *docg3, int block0, int block1, int page,
                         int wear, int ofs)
{
        int sector, ret = 0;

        doc_dbg("doc_seek(blocks=(%d,%d), page=%d, ofs=%d, wear=%d)\n",
                block0, block1, page, ofs, wear);

        if (!wear && (ofs < 2 * DOC_LAYOUT_PAGE_SIZE)) {
                doc_flash_sequence(docg3, DOC_SEQ_SET_PLANE1);
                doc_flash_command(docg3, DOC_CMD_READ_PLANE1);
                doc_delay(docg3, 2);
        } else {
                doc_flash_sequence(docg3, DOC_SEQ_SET_PLANE2);
                doc_flash_command(docg3, DOC_CMD_READ_PLANE2);
                doc_delay(docg3, 2);
        }

        doc_set_reliable_mode(docg3);
        if (wear)
                ret = doc_set_extra_page_mode(docg3);
        if (ret)
                goto out;

        doc_flash_sequence(docg3, DOC_SEQ_READ);
        sector = (block0 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
        doc_flash_command(docg3, DOC_CMD_PROG_BLOCK_ADDR);
        doc_setup_addr_sector(docg3, sector);

        sector = (block1 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
        doc_flash_command(docg3, DOC_CMD_PROG_BLOCK_ADDR);
        doc_setup_addr_sector(docg3, sector);
        doc_delay(docg3, 1);

out:
        return ret;
}

/**
 * doc_write_seek - Set both flash planes to the specified block, page for writing
 * @docg3: the device
 * @block0: the first plane block index
 * @block1: the second plane block index
 * @page: the page index within the block
 * @ofs: offset in page to write
 *
 * Programs the flash even and odd planes to the specific block and page.
 * Alternatively, programs the flash to the wear area of the specified page.
 */
static int doc_write_seek(struct docg3 *docg3, int block0, int block1, int page,
                         int ofs)
{
        int ret = 0, sector;

        doc_dbg("doc_write_seek(blocks=(%d,%d), page=%d, ofs=%d)\n",
                block0, block1, page, ofs);

        doc_set_reliable_mode(docg3);

        if (ofs < 2 * DOC_LAYOUT_PAGE_SIZE) {
                doc_flash_sequence(docg3, DOC_SEQ_SET_PLANE1);
                doc_flash_command(docg3, DOC_CMD_READ_PLANE1);
                doc_delay(docg3, 2);
        } else {
                doc_flash_sequence(docg3, DOC_SEQ_SET_PLANE2);
                doc_flash_command(docg3, DOC_CMD_READ_PLANE2);
                doc_delay(docg3, 2);
        }

        doc_flash_sequence(docg3, DOC_SEQ_PAGE_SETUP);
        doc_flash_command(docg3, DOC_CMD_PROG_CYCLE1);

        sector = (block0 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
        doc_setup_writeaddr_sector(docg3, sector, ofs);

        doc_flash_command(docg3, DOC_CMD_PROG_CYCLE3);
        doc_delay(docg3, 2);
        ret = doc_wait_ready(docg3);
        if (ret)
                goto out;

        doc_flash_command(docg3, DOC_CMD_PROG_CYCLE1);
        sector = (block1 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
        doc_setup_writeaddr_sector(docg3, sector, ofs);
        doc_delay(docg3, 1);

out:
        return ret;
}


/**
 * doc_read_page_ecc_init - Initialize hardware ECC engine
 * @docg3: the device
 * @len: the number of bytes covered by the ECC (BCH covered)
 *
 * The function does initialize the hardware ECC engine to compute the Hamming
 * ECC (on 1 byte) and the BCH hardware ECC (on 7 bytes).
 *
 * Return 0 if succeeded, -EIO on error
 */
static int doc_read_page_ecc_init(struct docg3 *docg3, int len)
{
        doc_writew(docg3, DOC_ECCCONF0_READ_MODE
                   | DOC_ECCCONF0_BCH_ENABLE | DOC_ECCCONF0_HAMMING_ENABLE
                   | (len & DOC_ECCCONF0_DATA_BYTES_MASK),
                   DOC_ECCCONF0);
        doc_delay(docg3, 4);
        doc_register_readb(docg3, DOC_FLASHCONTROL);
        return doc_wait_ready(docg3);
}

/**
 * doc_write_page_ecc_init - Initialize hardware BCH ECC engine
 * @docg3: the device
 * @len: the number of bytes covered by the ECC (BCH covered)
 *
 * The function does initialize the hardware ECC engine to compute the Hamming
 * ECC (on 1 byte) and the BCH hardware ECC (on 7 bytes).
 *
 * Return 0 if succeeded, -EIO on error
 */
static int doc_write_page_ecc_init(struct docg3 *docg3, int len)
{
        doc_writew(docg3, DOC_ECCCONF0_WRITE_MODE
                   | DOC_ECCCONF0_BCH_ENABLE | DOC_ECCCONF0_HAMMING_ENABLE
                   | (len & DOC_ECCCONF0_DATA_BYTES_MASK),
                   DOC_ECCCONF0);
        doc_delay(docg3, 4);
        doc_register_readb(docg3, DOC_FLASHCONTROL);
        return doc_wait_ready(docg3);
}

/**
 * doc_ecc_disable - Disable Hamming and BCH ECC hardware calculator
 * @docg3: the device
 *
 * Disables the hardware ECC generator and checker, for unchecked reads (as when
 * reading OOB only or write status byte).
 */
static void doc_ecc_disable(struct docg3 *docg3)
{
        doc_writew(docg3, DOC_ECCCONF0_READ_MODE, DOC_ECCCONF0);
        doc_delay(docg3, 4);
}

/**
 * doc_hamming_ecc_init - Initialize hardware Hamming ECC engine
 * @docg3: the device
 * @nb_bytes: the number of bytes covered by the ECC (Hamming covered)
 *
 * This function programs the ECC hardware to compute the hamming code on the
 * last provided N bytes to the hardware generator.
 */
static void doc_hamming_ecc_init(struct docg3 *docg3, int nb_bytes)
{
        u8 ecc_conf1;

        ecc_conf1 = doc_register_readb(docg3, DOC_ECCCONF1);
        ecc_conf1 &= ~DOC_ECCCONF1_HAMMING_BITS_MASK;
        ecc_conf1 |= (nb_bytes & DOC_ECCCONF1_HAMMING_BITS_MASK);
        doc_writeb(docg3, ecc_conf1, DOC_ECCCONF1);
}

/**
 * doc_ecc_bch_fix_data - Fix if need be read data from flash
 * @docg3: the device
 * @buf: the buffer of read data (512 + 7 + 1 bytes)
 * @hwecc: the hardware calculated ECC.
 *         It's in fact recv_ecc ^ calc_ecc, where recv_ecc was read from OOB
 *         area data, and calc_ecc the ECC calculated by the hardware generator.
 *
 * Checks if the received data matches the ECC, and if an error is detected,
 * tries to fix the bit flips (at most 4) in the buffer buf.  As the docg3
 * understands the (data, ecc, syndroms) in an inverted order in comparison to
 * the BCH library, the function reverses the order of bits (ie. bit7 and bit0,
 * bit6 and bit 1, ...) for all ECC data.
 *
 * The hardware ecc unit produces oob_ecc ^ calc_ecc.  The kernel's bch
 * algorithm is used to decode this.  However the hw operates on page
 * data in a bit order that is the reverse of that of the bch alg,
 * requiring that the bits be reversed on the result.  Thanks to Ivan
 * Djelic for his analysis.
 *
 * Returns number of fixed bits (0, 1, 2, 3, 4) or -EBADMSG if too many bit
 * errors were detected and cannot be fixed.
 */
static int doc_ecc_bch_fix_data(struct docg3 *docg3, void *buf, u8 *hwecc)
{
        u8 ecc[DOC_ECC_BCH_SIZE];
        int errorpos[DOC_ECC_BCH_T], i, numerrs;

        for (i = 0; i < DOC_ECC_BCH_SIZE; i++)
                ecc[i] = bitrev8(hwecc[i]);
        numerrs = decode_bch(docg3_bch, NULL, DOC_ECC_BCH_COVERED_BYTES,
                             NULL, ecc, NULL, errorpos);
        BUG_ON(numerrs == -EINVAL);
        if (numerrs < 0)
                goto out;

        for (i = 0; i < numerrs; i++)
                errorpos[i] = (errorpos[i] & ~7) | (7 - (errorpos[i] & 7));
        for (i = 0; i < numerrs; i++)
                if (errorpos[i] < DOC_ECC_BCH_COVERED_BYTES*8)
                        /* error is located in data, correct it */
                        change_bit(errorpos[i], buf);
out:
        doc_dbg("doc_ecc_bch_fix_data: flipped %d bits\n", numerrs);
        return numerrs;
}


/**
 * doc_read_page_prepare - Prepares reading data from a flash page
 * @docg3: the device
 * @block0: the first plane block index on flash memory
 * @block1: the second plane block index on flash memory
 * @page: the page index in the block
 * @offset: the offset in the page (must be a multiple of 4)
 *
 * Prepares the page to be read in the flash memory :
 *   - tell ASIC to map the flash pages
 *   - tell ASIC to be in read mode
 *
 * After a call to this method, a call to doc_read_page_finish is mandatory,
 * to end the read cycle of the flash.
 *
 * Read data from a flash page. The length to be read must be between 0 and
 * (page_size + oob_size + wear_size), ie. 532, and a multiple of 4 (because
 * the extra bytes reading is not implemented).
 *
 * As pages are grouped by 2 (in 2 planes), reading from a page must be done
 * in two steps:
 *  - one read of 512 bytes at offset 0
 *  - one read of 512 bytes at offset 512 + 16
 *
 * Returns 0 if successful, -EIO if a read error occured.
 */
static int doc_read_page_prepare(struct docg3 *docg3, int block0, int block1,
                                 int page, int offset)
{
        int wear_area = 0, ret = 0;

        doc_dbg("doc_read_page_prepare(blocks=(%d,%d), page=%d, ofsInPage=%d)\n",
                block0, block1, page, offset);
        if (offset >= DOC_LAYOUT_WEAR_OFFSET)
                wear_area = 1;
        if (!wear_area && offset > (DOC_LAYOUT_PAGE_OOB_SIZE * 2))
                return -EINVAL;

        doc_set_device_id(docg3, docg3->device_id);
        ret = doc_reset_seq(docg3);
        if (ret)
                goto err;

        /* Program the flash address block and page */
        ret = doc_read_seek(docg3, block0, block1, page, wear_area, offset);
        if (ret)
                goto err;

        doc_flash_command(docg3, DOC_CMD_READ_ALL_PLANES);
        doc_delay(docg3, 2);
        doc_wait_ready(docg3);

        doc_flash_command(docg3, DOC_CMD_SET_ADDR_READ);
        doc_delay(docg3, 1);
        if (offset >= DOC_LAYOUT_PAGE_SIZE * 2)
                offset -= 2 * DOC_LAYOUT_PAGE_SIZE;
        doc_flash_address(docg3, offset >> 2);
        doc_delay(docg3, 1);
        doc_wait_ready(docg3);

        doc_flash_command(docg3, DOC_CMD_READ_FLASH);

        return 0;
err:
        doc_writeb(docg3, 0, DOC_DATAEND);
        doc_delay(docg3, 2);
        return -EIO;
}

/**
 * doc_read_page_getbytes - Reads bytes from a prepared page
 * @docg3: the device
 * @len: the number of bytes to be read (must be a multiple of 4)
 * @buf: the buffer to be filled in
 * @first: 1 if first time read, DOC_READADDRESS should be set
 *
 */
static int doc_read_page_getbytes(struct docg3 *docg3, int len, u_char *buf,
                                  int first)
{
        doc_read_data_area(docg3, buf, len, first);
        doc_delay(docg3, 2);
        return len;
}

/**
 * doc_write_page_putbytes - Writes bytes into a prepared page
 * @docg3: the device
 * @len: the number of bytes to be written
 * @buf: the buffer of input bytes
 *
 */
static void doc_write_page_putbytes(struct docg3 *docg3, int len,
                                    const u_char *buf)
{
        doc_write_data_area(docg3, buf, len);
        doc_delay(docg3, 2);
}

/**
 * doc_get_bch_hw_ecc - Get hardware calculated BCH ECC
 * @docg3: the device
 * @hwecc:  the array of 7 integers where the hardware ecc will be stored
 */
static void doc_get_bch_hw_ecc(struct docg3 *docg3, u8 *hwecc)
{
        int i;

        for (i = 0; i < DOC_ECC_BCH_SIZE; i++)
                hwecc[i] = doc_register_readb(docg3, DOC_BCH_HW_ECC(i));
}

/**
 * doc_page_finish - Ends reading/writing of a flash page
 * @docg3: the device
 */
static void doc_page_finish(struct docg3 *docg3)
{
        doc_writeb(docg3, 0, DOC_DATAEND);
        doc_delay(docg3, 2);
}

/**
 * doc_read_page_finish - Ends reading of a flash page
 * @docg3: the device
 *
 * As a side effect, resets the chip selector to 0. This ensures that after each
 * read operation, the floor 0 is selected. Therefore, if the systems halts, the
 * reboot will boot on floor 0, where the IPL is.
 */
static void doc_read_page_finish(struct docg3 *docg3)
{
        doc_page_finish(docg3);
        doc_set_device_id(docg3, 0);
}

/**
 * calc_block_sector - Calculate blocks, pages and ofs.

 * @from: offset in flash
 * @block0: first plane block index calculated
 * @block1: second plane block index calculated
 * @page: page calculated
 * @ofs: offset in page
 * @reliable: 0 if docg3 in normal mode, 1 if docg3 in fast mode, 2 if docg3 in
 * reliable mode.
 *
 * The calculation is based on the reliable/normal mode. In normal mode, the 64
 * pages of a block are available. In reliable mode, as pages 2*n and 2*n+1 are
 * clones, only 32 pages per block are available.
 */
static void calc_block_sector(loff_t from, int *block0, int *block1, int *page,
                              int *ofs, int reliable)
{
        uint sector, pages_biblock;

        pages_biblock = DOC_LAYOUT_PAGES_PER_BLOCK * DOC_LAYOUT_NBPLANES;
        if (reliable == 1 || reliable == 2)
                pages_biblock /= 2;

        sector = from / DOC_LAYOUT_PAGE_SIZE;
        *block0 = sector / pages_biblock * DOC_LAYOUT_NBPLANES;
        *block1 = *block0 + 1;
        *page = sector % pages_biblock;
        *page /= DOC_LAYOUT_NBPLANES;
        if (reliable == 1 || reliable == 2)
                *page *= 2;
        if (sector % 2)
                *ofs = DOC_LAYOUT_PAGE_OOB_SIZE;
        else
                *ofs = 0;
}

/**
 * doc_read_oob - Read out of band bytes from flash
 * @mtd: the device
 * @from: the offset from first block and first page, in bytes, aligned on page
 *        size
 * @ops: the mtd oob structure
 *
 * Reads flash memory OOB area of pages.
 *
 * Returns 0 if read successfull, of -EIO, -EINVAL if an error occured
 */
static int doc_read_oob(struct mtd_info *mtd, loff_t from,
                        struct mtd_oob_ops *ops)
{
        struct docg3 *docg3 = mtd->priv;
        int block0, block1, page, ret, ofs = 0;
        u8 *oobbuf = ops->oobbuf;
        u8 *buf = ops->datbuf;
        size_t len, ooblen, nbdata, nboob;
        u8 hwecc[DOC_ECC_BCH_SIZE], eccconf1;

        if (buf)
                len = ops->len;
        else
                len = 0;
        if (oobbuf)
                ooblen = ops->ooblen;
        else
                ooblen = 0;

        if (oobbuf && ops->mode == MTD_OPS_PLACE_OOB)
                oobbuf += ops->ooboffs;

        doc_dbg("doc_read_oob(from=%lld, mode=%d, data=(%p:%zu), oob=(%p:%zu))\n",
                from, ops->mode, buf, len, oobbuf, ooblen);
        if ((len % DOC_LAYOUT_PAGE_SIZE) || (ooblen % DOC_LAYOUT_OOB_SIZE) ||
            (from % DOC_LAYOUT_PAGE_SIZE))
                return -EINVAL;

        ret = -EINVAL;
        calc_block_sector(from + len, &block0, &block1, &page, &ofs,
                          docg3->reliable);
        if (block1 > docg3->max_block)
                goto err;

        ops->oobretlen = 0;
        ops->retlen = 0;
        ret = 0;
        while (!ret && (len > 0 || ooblen > 0)) {
                calc_block_sector(from, &block0, &block1, &page, &ofs,
                        docg3->reliable);
                nbdata = min_t(size_t, len, (size_t)DOC_LAYOUT_PAGE_SIZE);
                nboob = min_t(size_t, ooblen, (size_t)DOC_LAYOUT_OOB_SIZE);
                ret = doc_read_page_prepare(docg3, block0, block1, page, ofs);
                if (ret < 0)
                        goto err;
                ret = doc_read_page_ecc_init(docg3, DOC_ECC_BCH_TOTAL_BYTES);
                if (ret < 0)
                        goto err_in_read;
                ret = doc_read_page_getbytes(docg3, nbdata, buf, 1);
                if (ret < nbdata)
                        goto err_in_read;
                doc_read_page_getbytes(docg3, DOC_LAYOUT_PAGE_SIZE - nbdata,
                                       NULL, 0);
                ret = doc_read_page_getbytes(docg3, nboob, oobbuf, 0);
                if (ret < nboob)
                        goto err_in_read;
                doc_read_page_getbytes(docg3, DOC_LAYOUT_OOB_SIZE - nboob,
                                       NULL, 0);

                doc_get_bch_hw_ecc(docg3, hwecc);
                eccconf1 = doc_register_readb(docg3, DOC_ECCCONF1);

                if (nboob >= DOC_LAYOUT_OOB_SIZE) {
                        doc_dbg("OOB - INFO: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
                                oobbuf[0], oobbuf[1], oobbuf[2], oobbuf[3],
                                oobbuf[4], oobbuf[5], oobbuf[6]);
                        doc_dbg("OOB - HAMMING: %02x\n", oobbuf[7]);
                        doc_dbg("OOB - BCH_ECC: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
                                oobbuf[8], oobbuf[9], oobbuf[10], oobbuf[11],
                                oobbuf[12], oobbuf[13], oobbuf[14]);
                        doc_dbg("OOB - UNUSED: %02x\n", oobbuf[15]);
                }
                doc_dbg("ECC checks: ECCConf1=%x\n", eccconf1);
                doc_dbg("ECC HW_ECC: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
                        hwecc[0], hwecc[1], hwecc[2], hwecc[3], hwecc[4],
                        hwecc[5], hwecc[6]);

                ret = -EIO;
                if (is_prot_seq_error(docg3))
                        goto err_in_read;
                ret = 0;
                if ((block0 >= DOC_LAYOUT_BLOCK_FIRST_DATA) &&
                    (eccconf1 & DOC_ECCCONF1_BCH_SYNDROM_ERR) &&
                    (eccconf1 & DOC_ECCCONF1_PAGE_IS_WRITTEN) &&
                    (ops->mode != MTD_OPS_RAW) &&
                    (nbdata == DOC_LAYOUT_PAGE_SIZE)) {
                        ret = doc_ecc_bch_fix_data(docg3, buf, hwecc);
                        if (ret < 0) {
                                mtd->ecc_stats.failed++;
                                ret = -EBADMSG;
                        }
                        if (ret > 0) {
                                mtd->ecc_stats.corrected += ret;
                                ret = -EUCLEAN;
                        }
                }

                doc_read_page_finish(docg3);
                ops->retlen += nbdata;
                ops->oobretlen += nboob;
                buf += nbdata;
                oobbuf += nboob;
                len -= nbdata;
                ooblen -= nboob;
                from += DOC_LAYOUT_PAGE_SIZE;
        }

        return ret;
err_in_read:
        doc_read_page_finish(docg3);
err:
        return ret;
}

/**
 * doc_read - Read bytes from flash
 * @mtd: the device
 * @from: the offset from first block and first page, in bytes, aligned on page
 *        size
 * @len: the number of bytes to read (must be a multiple of 4)
 * @retlen: the number of bytes actually read
 * @buf: the filled in buffer
 *
 * Reads flash memory pages. This function does not read the OOB chunk, but only
 * the page data.
 *
 * Returns 0 if read successfull, of -EIO, -EINVAL if an error occured
 */
static int doc_read(struct mtd_info *mtd, loff_t from, size_t len,
             size_t *retlen, u_char *buf)
{
        struct mtd_oob_ops ops;
        size_t ret;

        memset(&ops, 0, sizeof(ops));
        ops.datbuf = buf;
        ops.len = len;
        ops.mode = MTD_OPS_AUTO_OOB;

        ret = doc_read_oob(mtd, from, &ops);
        *retlen = ops.retlen;
        return ret;
}

static int doc_reload_bbt(struct docg3 *docg3)
{
        int block = DOC_LAYOUT_BLOCK_BBT;
        int ret = 0, nbpages, page;
        u_char *buf = docg3->bbt;

        nbpages = DIV_ROUND_UP(docg3->max_block + 1, 8 * DOC_LAYOUT_PAGE_SIZE);
        for (page = 0; !ret && (page < nbpages); page++) {
                ret = doc_read_page_prepare(docg3, block, block + 1,
                                            page + DOC_LAYOUT_PAGE_BBT, 0);
                if (!ret)
                        ret = doc_read_page_ecc_init(docg3,
                                                     DOC_LAYOUT_PAGE_SIZE);
                if (!ret)
                        doc_read_page_getbytes(docg3, DOC_LAYOUT_PAGE_SIZE,
                                               buf, 1);
                buf += DOC_LAYOUT_PAGE_SIZE;
        }
        doc_read_page_finish(docg3);
        return ret;
}

/**
 * doc_block_isbad - Checks whether a block is good or not
 * @mtd: the device
 * @from: the offset to find the correct block
 *
 * Returns 1 if block is bad, 0 if block is good
 */
static int doc_block_isbad(struct mtd_info *mtd, loff_t from)
{
        struct docg3 *docg3 = mtd->priv;
        int block0, block1, page, ofs, is_good;

        calc_block_sector(from, &block0, &block1, &page, &ofs,
                docg3->reliable);
        doc_dbg("doc_block_isbad(from=%lld) => block=(%d,%d), page=%d, ofs=%d\n",
                from, block0, block1, page, ofs);

        if (block0 < DOC_LAYOUT_BLOCK_FIRST_DATA)
                return 0;
        if (block1 > docg3->max_block)
                return -EINVAL;

        is_good = docg3->bbt[block0 >> 3] & (1 << (block0 & 0x7));
        return !is_good;
}

#if 0
/**
 * doc_get_erase_count - Get block erase count
 * @docg3: the device
 * @from: the offset in which the block is.
 *
 * Get the number of times a block was erased. The number is the maximum of
 * erase times between first and second plane (which should be equal normally).
 *
 * Returns The number of erases, or -EINVAL or -EIO on error.
 */
static int doc_get_erase_count(struct docg3 *docg3, loff_t from)
{
        u8 buf[DOC_LAYOUT_WEAR_SIZE];
        int ret, plane1_erase_count, plane2_erase_count;
        int block0, block1, page, ofs;

        doc_dbg("doc_get_erase_count(from=%lld, buf=%p)\n", from, buf);
        if (from % DOC_LAYOUT_PAGE_SIZE)
                return -EINVAL;
        calc_block_sector(from, &block0, &block1, &page, &ofs, docg3->reliable);
        if (block1 > docg3->max_block)
                return -EINVAL;

        ret = doc_reset_seq(docg3);
        if (!ret)
                ret = doc_read_page_prepare(docg3, block0, block1, page,
                                            ofs + DOC_LAYOUT_WEAR_OFFSET);
        if (!ret)
                ret = doc_read_page_getbytes(docg3, DOC_LAYOUT_WEAR_SIZE,
                                             buf, 1);
        doc_read_page_finish(docg3);

        if (ret || (buf[0] != DOC_ERASE_MARK) || (buf[2] != DOC_ERASE_MARK))
                return -EIO;
        plane1_erase_count = (u8)(~buf[1]) | ((u8)(~buf[4]) << 8)
                | ((u8)(~buf[5]) << 16);
        plane2_erase_count = (u8)(~buf[3]) | ((u8)(~buf[6]) << 8)
                | ((u8)(~buf[7]) << 16);

        return max(plane1_erase_count, plane2_erase_count);
}
#endif

/**
 * doc_get_op_status - get erase/write operation status
 * @docg3: the device
 *
 * Queries the status from the chip, and returns it
 *
 * Returns the status (bits DOC_PLANES_STATUS_*)
 */
static int doc_get_op_status(struct docg3 *docg3)
{
        u8 status;

        doc_flash_sequence(docg3, DOC_SEQ_PLANES_STATUS);
        doc_flash_command(docg3, DOC_CMD_PLANES_STATUS);
        doc_delay(docg3, 5);

        doc_ecc_disable(docg3);
        doc_read_data_area(docg3, &status, 1, 1);
        return status;
}

/**
 * doc_write_erase_wait_status - wait for write or erase completion
 * @docg3: the device
 *
 * Wait for the chip to be ready again after erase or write operation, and check
 * erase/write status.
 *
 * Returns 0 if erase successfull, -EIO if erase/write issue, -ETIMEOUT if
 * timeout
 */
static int doc_write_erase_wait_status(struct docg3 *docg3)
{
        int status, ret = 0;

        if (!doc_is_ready(docg3))
                usleep_range(3000, 3000);
        if (!doc_is_ready(docg3)) {
                doc_dbg("Timeout reached and the chip is still not ready\n");
                ret = -EAGAIN;
                goto out;
        }

        status = doc_get_op_status(docg3);
        if (status & DOC_PLANES_STATUS_FAIL) {
                doc_dbg("Erase/Write failed on (a) plane(s), status = %x\n",
                        status);
                ret = -EIO;
        }

out:
        doc_page_finish(docg3);
        return ret;
}

/**
 * doc_erase_block - Erase a couple of blocks
 * @docg3: the device
 * @block0: the first block to erase (leftmost plane)
 * @block1: the second block to erase (rightmost plane)
 *
 * Erase both blocks, and return operation status
 *
 * Returns 0 if erase successful, -EIO if erase issue, -ETIMEOUT if chip not
 * ready for too long
 */
static int doc_erase_block(struct docg3 *docg3, int block0, int block1)
{
        int ret, sector;

        doc_dbg("doc_erase_block(blocks=(%d,%d))\n", block0, block1);
        ret = doc_reset_seq(docg3);
        if (ret)
                return -EIO;

        doc_set_reliable_mode(docg3);
        doc_flash_sequence(docg3, DOC_SEQ_ERASE);

        sector = block0 << DOC_ADDR_BLOCK_SHIFT;
        doc_flash_command(docg3, DOC_CMD_PROG_BLOCK_ADDR);
        doc_setup_addr_sector(docg3, sector);
        sector = block1 << DOC_ADDR_BLOCK_SHIFT;
        doc_flash_command(docg3, DOC_CMD_PROG_BLOCK_ADDR);
        doc_setup_addr_sector(docg3, sector);
        doc_delay(docg3, 1);

        doc_flash_command(docg3, DOC_CMD_ERASECYCLE2);
        doc_delay(docg3, 2);

        if (is_prot_seq_error(docg3)) {
                doc_err("Erase blocks %d,%d error\n", block0, block1);
                return -EIO;
        }

        return doc_write_erase_wait_status(docg3);
}

/**
 * doc_erase - Erase a portion of the chip
 * @mtd: the device
 * @info: the erase info
 *
 * Erase a bunch of contiguous blocks, by pairs, as a "mtd" page of 1024 is
 * split into 2 pages of 512 bytes on 2 contiguous blocks.
 *
 * Returns 0 if erase successful, -EINVAL if adressing error, -EIO if erase
 * issue
 */
static int doc_erase(struct mtd_info *mtd, struct erase_info *info)
{
        struct docg3 *docg3 = mtd->priv;
        uint64_t len;
        int block0, block1, page, ret, ofs = 0;

        doc_dbg("doc_erase(from=%lld, len=%lld\n", info->addr, info->len);
        doc_set_device_id(docg3, docg3->device_id);

        info->state = MTD_ERASE_PENDING;
        calc_block_sector(info->addr + info->len, &block0, &block1, &page,
                          &ofs, docg3->reliable);
        ret = -EINVAL;
        if (block1 > docg3->max_block || page || ofs)
                goto reset_err;

        ret = 0;
        calc_block_sector(info->addr, &block0, &block1, &page, &ofs,
                          docg3->reliable);
        doc_set_reliable_mode(docg3);
        for (len = info->len; !ret && len > 0; len -= mtd->erasesize) {
                info->state = MTD_ERASING;
                ret = doc_erase_block(docg3, block0, block1);
                block0 += 2;
                block1 += 2;
        }

        if (ret)
                goto reset_err;

        info->state = MTD_ERASE_DONE;
        return 0;

reset_err:
        info->state = MTD_ERASE_FAILED;
        return ret;
}

/**
 * doc_write_page - Write a single page to the chip
 * @docg3: the device
 * @to: the offset from first block and first page, in bytes, aligned on page
 *      size
 * @buf: buffer to get bytes from
 * @oob: buffer to get out of band bytes from (can be NULL if no OOB should be
 *       written)
 * @autoecc: if 0, all 16 bytes from OOB are taken, regardless of HW Hamming or
 *           BCH computations. If 1, only bytes 0-7 and byte 15 are taken,
 *           remaining ones are filled with hardware Hamming and BCH
 *           computations. Its value is not meaningfull is oob == NULL.
 *
 * Write one full page (ie. 1 page split on two planes), of 512 bytes, with the
 * OOB data. The OOB ECC is automatically computed by the hardware Hamming and
 * BCH generator if autoecc is not null.
 *
 * Returns 0 if write successful, -EIO if write error, -EAGAIN if timeout
 */
static int doc_write_page(struct docg3 *docg3, loff_t to, const u_char *buf,
                          const u_char *oob, int autoecc)
{
        int block0, block1, page, ret, ofs = 0;
        u8 hwecc[DOC_ECC_BCH_SIZE], hamming;

        doc_dbg("doc_write_page(to=%lld)\n", to);
        calc_block_sector(to, &block0, &block1, &page, &ofs, docg3->reliable);

        doc_set_device_id(docg3, docg3->device_id);
        ret = doc_reset_seq(docg3);
        if (ret)
                goto err;

        /* Program the flash address block and page */
        ret = doc_write_seek(docg3, block0, block1, page, ofs);
        if (ret)
                goto err;

        doc_write_page_ecc_init(docg3, DOC_ECC_BCH_TOTAL_BYTES);
        doc_delay(docg3, 2);
        doc_write_page_putbytes(docg3, DOC_LAYOUT_PAGE_SIZE, buf);

        if (oob && autoecc) {
                doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_PAGEINFO_SZ, oob);
                doc_delay(docg3, 2);
                oob += DOC_LAYOUT_OOB_UNUSED_OFS;

                hamming = doc_register_readb(docg3, DOC_HAMMINGPARITY);
                doc_delay(docg3, 2);
                doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_HAMMING_SZ,
                                        &hamming);
                doc_delay(docg3, 2);

                doc_get_bch_hw_ecc(docg3, hwecc);
                doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_BCH_SZ, hwecc);
                doc_delay(docg3, 2);

                doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_UNUSED_SZ, oob);
        }
        if (oob && !autoecc)
                doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_SIZE, oob);

        doc_delay(docg3, 2);
        doc_page_finish(docg3);
        doc_delay(docg3, 2);
        doc_flash_command(docg3, DOC_CMD_PROG_CYCLE2);
        doc_delay(docg3, 2);

        /*
         * The wait status will perform another doc_page_finish() call, but that
         * seems to please the docg3, so leave it.
         */
        ret = doc_write_erase_wait_status(docg3);
        return ret;
err:
        doc_read_page_finish(docg3);
        return ret;
}

/**
 * doc_guess_autoecc - Guess autoecc mode from mbd_oob_ops
 * @ops: the oob operations
 *
 * Returns 0 or 1 if success, -EINVAL if invalid oob mode
 */
static int doc_guess_autoecc(struct mtd_oob_ops *ops)
{
        int autoecc;

        switch (ops->mode) {
        case MTD_OPS_PLACE_OOB:
        case MTD_OPS_AUTO_OOB:
                autoecc = 1;
                break;
        case MTD_OPS_RAW:
                autoecc = 0;
                break;
        default:
                autoecc = -EINVAL;
        }
        return autoecc;
}

/**
 * doc_fill_autooob - Fill a 16 bytes OOB from 8 non-ECC bytes
 * @dst: the target 16 bytes OOB buffer
 * @oobsrc: the source 8 bytes non-ECC OOB buffer
 *
 */
static void doc_fill_autooob(u8 *dst, u8 *oobsrc)
{
        memcpy(dst, oobsrc, DOC_LAYOUT_OOB_PAGEINFO_SZ);
        dst[DOC_LAYOUT_OOB_UNUSED_OFS] = oobsrc[DOC_LAYOUT_OOB_PAGEINFO_SZ];
}

/**
 * doc_backup_oob - Backup OOB into docg3 structure
 * @docg3: the device
 * @to: the page offset in the chip
 * @ops: the OOB size and buffer
 *
 * As the docg3 should write a page with its OOB in one pass, and some userland
 * applications do write_oob() to setup the OOB and then write(), store the OOB
 * into a temporary storage. This is very dangerous, as 2 concurrent
 * applications could store an OOB, and then write their pages (which will
 * result into one having its OOB corrupted).
 *
 * The only reliable way would be for userland to call doc_write_oob() with both
 * the page data _and_ the OOB area.
 *
 * Returns 0 if success, -EINVAL if ops content invalid
 */
static int doc_backup_oob(struct docg3 *docg3, loff_t to,
                          struct mtd_oob_ops *ops)
{
        int ooblen = ops->ooblen, autoecc;

        if (ooblen != DOC_LAYOUT_OOB_SIZE)
                return -EINVAL;
        autoecc = doc_guess_autoecc(ops);
        if (autoecc < 0)
                return autoecc;

        docg3->oob_write_ofs = to;
        docg3->oob_autoecc = autoecc;
        if (ops->mode == MTD_OPS_AUTO_OOB) {
                doc_fill_autooob(docg3->oob_write_buf, ops->oobbuf);
                ops->oobretlen = 8;
        } else {
                memcpy(docg3->oob_write_buf, ops->oobbuf, DOC_LAYOUT_OOB_SIZE);
                ops->oobretlen = DOC_LAYOUT_OOB_SIZE;
        }
        return 0;
}

/**
 * doc_write_oob - Write out of band bytes to flash
 * @mtd: the device
 * @ofs: the offset from first block and first page, in bytes, aligned on page
 *       size
 * @ops: the mtd oob structure
 *
 * Either write OOB data into a temporary buffer, for the subsequent write
 * page. The provided OOB should be 16 bytes long. If a data buffer is provided
 * as well, issue the page write.
 * Or provide data without OOB, and then a all zeroed OOB will be used (ECC will
 * still be filled in if asked for).
 *
 * Returns 0 is successfull, EINVAL if length is not 14 bytes
 */
static int doc_write_oob(struct mtd_info *mtd, loff_t ofs,
                         struct mtd_oob_ops *ops)
{
        struct docg3 *docg3 = mtd->priv;
        int block0, block1, page, ret, pofs = 0, autoecc, oobdelta;
        u8 *oobbuf = ops->oobbuf;
        u8 *buf = ops->datbuf;
        size_t len, ooblen;
        u8 oob[DOC_LAYOUT_OOB_SIZE];

        if (buf)
                len = ops->len;
        else
                len = 0;
        if (oobbuf)
                ooblen = ops->ooblen;
        else
                ooblen = 0;

        if (oobbuf && ops->mode == MTD_OPS_PLACE_OOB)
                oobbuf += ops->ooboffs;

        doc_dbg("doc_write_oob(from=%lld, mode=%d, data=(%p:%zu), oob=(%p:%zu))\n",
                ofs, ops->mode, buf, len, oobbuf, ooblen);
        switch (ops->mode) {
        case MTD_OPS_PLACE_OOB:
        case MTD_OPS_RAW:
                oobdelta = mtd->oobsize;
                break;
        case MTD_OPS_AUTO_OOB:
                oobdelta = mtd->ecclayout->oobavail;
                break;
        default:
                oobdelta = 0;
        }
        if ((len % DOC_LAYOUT_PAGE_SIZE) || (ooblen % oobdelta) ||
            (ofs % DOC_LAYOUT_PAGE_SIZE))
                return -EINVAL;
        if (len && ooblen &&
            (len / DOC_LAYOUT_PAGE_SIZE) != (ooblen / oobdelta))
                return -EINVAL;

        ret = -EINVAL;
        calc_block_sector(ofs + len, &block0, &block1, &page, &pofs,
                          docg3->reliable);
        if (block1 > docg3->max_block)
                goto err;

        ops->oobretlen = 0;
        ops->retlen = 0;
        ret = 0;
        if (len == 0 && ooblen == 0)
                return -EINVAL;
        if (len == 0 && ooblen > 0)
                return doc_backup_oob(docg3, ofs, ops);

        autoecc = doc_guess_autoecc(ops);
        if (autoecc < 0)
                return autoecc;

        while (!ret && len > 0) {
                memset(oob, 0, sizeof(oob));
                if (ofs == docg3->oob_write_ofs)
                        memcpy(oob, docg3->oob_write_buf, DOC_LAYOUT_OOB_SIZE);
                else if (ooblen > 0 && ops->mode == MTD_OPS_AUTO_OOB)
                        doc_fill_autooob(oob, oobbuf);
                else if (ooblen > 0)
                        memcpy(oob, oobbuf, DOC_LAYOUT_OOB_SIZE);
                ret = doc_write_page(docg3, ofs, buf, oob, autoecc);

                ofs += DOC_LAYOUT_PAGE_SIZE;
                len -= DOC_LAYOUT_PAGE_SIZE;
                buf += DOC_LAYOUT_PAGE_SIZE;
                if (ooblen) {
                        oobbuf += oobdelta;
                        ooblen -= oobdelta;
                        ops->oobretlen += oobdelta;
                }
                ops->retlen += DOC_LAYOUT_PAGE_SIZE;
        }
err:
        doc_set_device_id(docg3, 0);
        return ret;
}

/**
 * doc_write - Write a buffer to the chip
 * @mtd: the device
 * @to: the offset from first block and first page, in bytes, aligned on page
 *      size
 * @len: the number of bytes to write (must be a full page size, ie. 512)
 * @retlen: the number of bytes actually written (0 or 512)
 * @buf: the buffer to get bytes from
 *
 * Writes data to the chip.
 *
 * Returns 0 if write successful, -EIO if write error
 */
static int doc_write(struct mtd_info *mtd, loff_t to, size_t len,
                     size_t *retlen, const u_char *buf)
{
        struct docg3 *docg3 = mtd->priv;
        int ret;
        struct mtd_oob_ops ops;

        doc_dbg("doc_write(to=%lld, len=%zu)\n", to, len);
        ops.datbuf = (char *)buf;
        ops.len = len;
        ops.mode = MTD_OPS_PLACE_OOB;
        ops.oobbuf = NULL;
        ops.ooblen = 0;
        ops.ooboffs = 0;

        ret = doc_write_oob(mtd, to, &ops);
        *retlen = ops.retlen;
        return ret;
}

static struct docg3 *sysfs_dev2docg3(struct device *dev,
                                     struct device_attribute *attr)
{
        int floor;
        struct platform_device *pdev = to_platform_device(dev);
        struct mtd_info **docg3_floors = platform_get_drvdata(pdev);

        floor = attr->attr.name[1] - '0';
        if (floor < 0 || floor >= DOC_MAX_NBFLOORS)
                return NULL;
        else
                return docg3_floors[floor]->priv;
}

static ssize_t dps0_is_key_locked(struct device *dev,
                                  struct device_attribute *attr, char *buf)
{
        struct docg3 *docg3 = sysfs_dev2docg3(dev, attr);
        int dps0;

        doc_set_device_id(docg3, docg3->device_id);
        dps0 = doc_register_readb(docg3, DOC_DPS0_STATUS);
        doc_set_device_id(docg3, 0);

        return sprintf(buf, "%d\n", !(dps0 & DOC_DPS_KEY_OK));
}

static ssize_t dps1_is_key_locked(struct device *dev,
                                  struct device_attribute *attr, char *buf)
{
        struct docg3 *docg3 = sysfs_dev2docg3(dev, attr);
        int dps1;

        doc_set_device_id(docg3, docg3->device_id);
        dps1 = doc_register_readb(docg3, DOC_DPS1_STATUS);
        doc_set_device_id(docg3, 0);

        return sprintf(buf, "%d\n", !(dps1 & DOC_DPS_KEY_OK));
}

static ssize_t dps0_insert_key(struct device *dev,
                               struct device_attribute *attr,
                               const char *buf, size_t count)
{
        struct docg3 *docg3 = sysfs_dev2docg3(dev, attr);
        int i;

        if (count != DOC_LAYOUT_DPS_KEY_LENGTH)
                return -EINVAL;

        doc_set_device_id(docg3, docg3->device_id);
        for (i = 0; i < DOC_LAYOUT_DPS_KEY_LENGTH; i++)
                doc_writeb(docg3, buf[i], DOC_DPS0_KEY);
        doc_set_device_id(docg3, 0);
        return count;
}

static ssize_t dps1_insert_key(struct device *dev,
                               struct device_attribute *attr,
                               const char *buf, size_t count)
{
        struct docg3 *docg3 = sysfs_dev2docg3(dev, attr);
        int i;

        if (count != DOC_LAYOUT_DPS_KEY_LENGTH)
                return -EINVAL;

        doc_set_device_id(docg3, docg3->device_id);
        for (i = 0; i < DOC_LAYOUT_DPS_KEY_LENGTH; i++)
                doc_writeb(docg3, buf[i], DOC_DPS1_KEY);
        doc_set_device_id(docg3, 0);
        return count;
}

#define FLOOR_SYSFS(id) { \
        __ATTR(f##id##_dps0_is_keylocked, S_IRUGO, dps0_is_key_locked, NULL), \
        __ATTR(f##id##_dps1_is_keylocked, S_IRUGO, dps1_is_key_locked, NULL), \
        __ATTR(f##id##_dps0_protection_key, S_IWUGO, NULL, dps0_insert_key), \
        __ATTR(f##id##_dps1_protection_key, S_IWUGO, NULL, dps1_insert_key), \
}

static struct device_attribute doc_sys_attrs[DOC_MAX_NBFLOORS][4] = {
        FLOOR_SYSFS(0), FLOOR_SYSFS(1), FLOOR_SYSFS(2), FLOOR_SYSFS(3)
};

static int doc_register_sysfs(struct platform_device *pdev,
                              struct mtd_info **floors)
{
        int ret = 0, floor, i = 0;
        struct device *dev = &pdev->dev;

        for (floor = 0; !ret && floor < DOC_MAX_NBFLOORS && floors[floor];
             floor++)
                for (i = 0; !ret && i < 4; i++)
                        ret = device_create_file(dev, &doc_sys_attrs[floor][i]);
        if (!ret)
                return 0;
        do {
                while (--i >= 0)
                        device_remove_file(dev, &doc_sys_attrs[floor][i]);
                i = 4;
        } while (--floor >= 0);
        return ret;
}

static void doc_unregister_sysfs(struct platform_device *pdev,
                                 struct mtd_info **floors)
{
        struct device *dev = &pdev->dev;
        int floor, i;

        for (floor = 0; floor < DOC_MAX_NBFLOORS && floors[floor];
             floor++)
                for (i = 0; i < 4; i++)
                        device_remove_file(dev, &doc_sys_attrs[floor][i]);
}

/*
 * Debug sysfs entries
 */
static int dbg_flashctrl_show(struct seq_file *s, void *p)
{
        struct docg3 *docg3 = (struct docg3 *)s->private;

        int pos = 0;
        u8 fctrl = doc_register_readb(docg3, DOC_FLASHCONTROL);

        pos += seq_printf(s,
                 "FlashControl : 0x%02x (%s,CE# %s,%s,%s,flash %s)\n",
                 fctrl,
                 fctrl & DOC_CTRL_VIOLATION ? "protocol violation" : "-",
                 fctrl & DOC_CTRL_CE ? "active" : "inactive",
                 fctrl & DOC_CTRL_PROTECTION_ERROR ? "protection error" : "-",
                 fctrl & DOC_CTRL_SEQUENCE_ERROR ? "sequence error" : "-",
                 fctrl & DOC_CTRL_FLASHREADY ? "ready" : "not ready");
        return pos;
}
DEBUGFS_RO_ATTR(flashcontrol, dbg_flashctrl_show);

static int dbg_asicmode_show(struct seq_file *s, void *p)
{
        struct docg3 *docg3 = (struct docg3 *)s->private;

        int pos = 0;
        int pctrl = doc_register_readb(docg3, DOC_ASICMODE);
        int mode = pctrl & 0x03;

        pos += seq_printf(s,
                         "%04x : RAM_WE=%d,RSTIN_RESET=%d,BDETCT_RESET=%d,WRITE_ENABLE=%d,POWERDOWN=%d,MODE=%d%d (",
                         pctrl,
                         pctrl & DOC_ASICMODE_RAM_WE ? 1 : 0,
                         pctrl & DOC_ASICMODE_RSTIN_RESET ? 1 : 0,
                         pctrl & DOC_ASICMODE_BDETCT_RESET ? 1 : 0,
                         pctrl & DOC_ASICMODE_MDWREN ? 1 : 0,
                         pctrl & DOC_ASICMODE_POWERDOWN ? 1 : 0,
                         mode >> 1, mode & 0x1);

        switch (mode) {
        case DOC_ASICMODE_RESET:
                pos += seq_printf(s, "reset");
                break;
        case DOC_ASICMODE_NORMAL:
                pos += seq_printf(s, "normal");
                break;
        case DOC_ASICMODE_POWERDOWN:
                pos += seq_printf(s, "powerdown");
                break;
        }
        pos += seq_printf(s, ")\n");
        return pos;
}
DEBUGFS_RO_ATTR(asic_mode, dbg_asicmode_show);

static int dbg_device_id_show(struct seq_file *s, void *p)
{
        struct docg3 *docg3 = (struct docg3 *)s->private;
        int pos = 0;
        int id = doc_register_readb(docg3, DOC_DEVICESELECT);

        pos += seq_printf(s, "DeviceId = %d\n", id);
        return pos;
}
DEBUGFS_RO_ATTR(device_id, dbg_device_id_show);

static int dbg_protection_show(struct seq_file *s, void *p)
{
        struct docg3 *docg3 = (struct docg3 *)s->private;
        int pos = 0;
        int protect, dps0, dps0_low, dps0_high, dps1, dps1_low, dps1_high;

        protect = doc_register_readb(docg3, DOC_PROTECTION);
        dps0 = doc_register_readb(docg3, DOC_DPS0_STATUS);
        dps0_low = doc_register_readw(docg3, DOC_DPS0_ADDRLOW);
        dps0_high = doc_register_readw(docg3, DOC_DPS0_ADDRHIGH);
        dps1 = doc_register_readb(docg3, DOC_DPS1_STATUS);
        dps1_low = doc_register_readw(docg3, DOC_DPS1_ADDRLOW);
        dps1_high = doc_register_readw(docg3, DOC_DPS1_ADDRHIGH);

        pos += seq_printf(s, "Protection = 0x%02x (",
                         protect);
        if (protect & DOC_PROTECT_FOUNDRY_OTP_LOCK)
                pos += seq_printf(s, "FOUNDRY_OTP_LOCK,");
        if (protect & DOC_PROTECT_CUSTOMER_OTP_LOCK)
                pos += seq_printf(s, "CUSTOMER_OTP_LOCK,");
        if (protect & DOC_PROTECT_LOCK_INPUT)
                pos += seq_printf(s, "LOCK_INPUT,");
        if (protect & DOC_PROTECT_STICKY_LOCK)
                pos += seq_printf(s, "STICKY_LOCK,");
        if (protect & DOC_PROTECT_PROTECTION_ENABLED)
                pos += seq_printf(s, "PROTECTION ON,");
        if (protect & DOC_PROTECT_IPL_DOWNLOAD_LOCK)
                pos += seq_printf(s, "IPL_DOWNLOAD_LOCK,");
        if (protect & DOC_PROTECT_PROTECTION_ERROR)
                pos += seq_printf(s, "PROTECT_ERR,");
        else
                pos += seq_printf(s, "NO_PROTECT_ERR");
        pos += seq_printf(s, ")\n");

        pos += seq_printf(s, "DPS0 = 0x%02x : "
                         "Protected area [0x%x - 0x%x] : OTP=%d, READ=%d, "
                         "WRITE=%d, HW_LOCK=%d, KEY_OK=%d\n",
                         dps0, dps0_low, dps0_high,
                         !!(dps0 & DOC_DPS_OTP_PROTECTED),
                         !!(dps0 & DOC_DPS_READ_PROTECTED),
                         !!(dps0 & DOC_DPS_WRITE_PROTECTED),
                         !!(dps0 & DOC_DPS_HW_LOCK_ENABLED),
                         !!(dps0 & DOC_DPS_KEY_OK));
        pos += seq_printf(s, "DPS1 = 0x%02x : "
                         "Protected area [0x%x - 0x%x] : OTP=%d, READ=%d, "
                         "WRITE=%d, HW_LOCK=%d, KEY_OK=%d\n",
                         dps1, dps1_low, dps1_high,
                         !!(dps1 & DOC_DPS_OTP_PROTECTED),
                         !!(dps1 & DOC_DPS_READ_PROTECTED),
                         !!(dps1 & DOC_DPS_WRITE_PROTECTED),
                         !!(dps1 & DOC_DPS_HW_LOCK_ENABLED),
                         !!(dps1 & DOC_DPS_KEY_OK));
        return pos;
}
DEBUGFS_RO_ATTR(protection, dbg_protection_show);

static int __init doc_dbg_register(struct docg3 *docg3)
{
        struct dentry *root, *entry;

        root = debugfs_create_dir("docg3", NULL);
        if (!root)
                return -ENOMEM;

        entry = debugfs_create_file("flashcontrol", S_IRUSR, root, docg3,
                                  &flashcontrol_fops);
        if (entry)
                entry = debugfs_create_file("asic_mode", S_IRUSR, root,
                                            docg3, &asic_mode_fops);
        if (entry)
                entry = debugfs_create_file("device_id", S_IRUSR, root,
                                            docg3, &device_id_fops);
        if (entry)
                entry = debugfs_create_file("protection", S_IRUSR, root,
                                            docg3, &protection_fops);
        if (entry) {
                docg3->debugfs_root = root;
                return 0;
        } else {
                debugfs_remove_recursive(root);
                return -ENOMEM;
        }
}

static void __exit doc_dbg_unregister(struct docg3 *docg3)
{
        debugfs_remove_recursive(docg3->debugfs_root);
}

/**
 * doc_set_driver_info - Fill the mtd_info structure and docg3 structure
 * @chip_id: The chip ID of the supported chip
 * @mtd: The structure to fill
 */
static void __init doc_set_driver_info(int chip_id, struct mtd_info *mtd)
{
        struct docg3 *docg3 = mtd->priv;
        int cfg;

        cfg = doc_register_readb(docg3, DOC_CONFIGURATION);
        docg3->if_cfg = (cfg & DOC_CONF_IF_CFG ? 1 : 0);
        docg3->reliable = reliable_mode;

        switch (chip_id) {
        case DOC_CHIPID_G3:
                mtd->name = kasprintf(GFP_KERNEL, "DiskOnChip G3 floor %d",
                                      docg3->device_id);
                docg3->max_block = 2047;
                break;
        }
        mtd->type = MTD_NANDFLASH;
        mtd->flags = MTD_CAP_NANDFLASH;
        mtd->size = (docg3->max_block + 1) * DOC_LAYOUT_BLOCK_SIZE;
        if (docg3->reliable == 2)
                mtd->size /= 2;
        mtd->erasesize = DOC_LAYOUT_BLOCK_SIZE * DOC_LAYOUT_NBPLANES;
        if (docg3->reliable == 2)
                mtd->erasesize /= 2;
        mtd->writebufsize = mtd->writesize = DOC_LAYOUT_PAGE_SIZE;
        mtd->oobsize = DOC_LAYOUT_OOB_SIZE;
        mtd->owner = THIS_MODULE;
        mtd->erase = doc_erase;
        mtd->read = doc_read;
        mtd->write = doc_write;
        mtd->read_oob = doc_read_oob;
        mtd->write_oob = doc_write_oob;
        mtd->block_isbad = doc_block_isbad;
        mtd->ecclayout = &docg3_oobinfo;
}

/**
 * doc_probe_device - Check if a device is available
 * @base: the io space where the device is probed
 * @floor: the floor of the probed device
 * @dev: the device
 *
 * Checks whether a device at the specified IO range, and floor is available.
 *
 * Returns a mtd_info struct if there is a device, ENODEV if none found, ENOMEM
 * if a memory allocation failed. If floor 0 is checked, a reset of the ASIC is
 * launched.
 */
static struct mtd_info *doc_probe_device(void __iomem *base, int floor,
                                         struct device *dev)
{
        int ret, bbt_nbpages;
        u16 chip_id, chip_id_inv;
        struct docg3 *docg3;
        struct mtd_info *mtd;

        ret = -ENOMEM;
        docg3 = kzalloc(sizeof(struct docg3), GFP_KERNEL);
        if (!docg3)
                goto nomem1;
        mtd = kzalloc(sizeof(struct mtd_info), GFP_KERNEL);
        if (!mtd)
                goto nomem2;
        mtd->priv = docg3;
        bbt_nbpages = DIV_ROUND_UP(docg3->max_block + 1,
                                   8 * DOC_LAYOUT_PAGE_SIZE);
        docg3->bbt = kzalloc(bbt_nbpages * DOC_LAYOUT_PAGE_SIZE, GFP_KERNEL);
        if (!docg3->bbt)
                goto nomem3;

        docg3->dev = dev;
        docg3->device_id = floor;
        docg3->base = base;
        doc_set_device_id(docg3, docg3->device_id);
        if (!floor)
                doc_set_asic_mode(docg3, DOC_ASICMODE_RESET);
        doc_set_asic_mode(docg3, DOC_ASICMODE_NORMAL);

        chip_id = doc_register_readw(docg3, DOC_CHIPID);
        chip_id_inv = doc_register_readw(docg3, DOC_CHIPID_INV);

        ret = 0;
        if (chip_id != (u16)(~chip_id_inv)) {
                goto nomem3;
        }

        switch (chip_id) {
        case DOC_CHIPID_G3:
                doc_info("Found a G3 DiskOnChip at addr %p, floor %d\n",
                         base, floor);
                break;
        default:
                doc_err("Chip id %04x is not a DiskOnChip G3 chip\n", chip_id);
                goto nomem3;
        }

        doc_set_driver_info(chip_id, mtd);

        doc_hamming_ecc_init(docg3, DOC_LAYOUT_OOB_PAGEINFO_SZ);
        doc_reload_bbt(docg3);
        return mtd;

nomem3:
        kfree(mtd);
nomem2:
        kfree(docg3);
nomem1:
        return ERR_PTR(ret);
}

/**
 * doc_release_device - Release a docg3 floor
 * @mtd: the device
 */
static void doc_release_device(struct mtd_info *mtd)
{
        struct docg3 *docg3 = mtd->priv;

        mtd_device_unregister(mtd);
        kfree(docg3->bbt);
        kfree(docg3);
        kfree(mtd->name);
        kfree(mtd);
}

/**
 * docg3_resume - Awakens docg3 floor
 * @pdev: platfrom device
 *
 * Returns 0 (always successfull)
 */
static int docg3_resume(struct platform_device *pdev)
{
        int i;
        struct mtd_info **docg3_floors, *mtd;
        struct docg3 *docg3;

        docg3_floors = platform_get_drvdata(pdev);
        mtd = docg3_floors[0];
        docg3 = mtd->priv;

        doc_dbg("docg3_resume()\n");
        for (i = 0; i < 12; i++)
                doc_readb(docg3, DOC_IOSPACE_IPL);
        return 0;
}

/**
 * docg3_suspend - Put in low power mode the docg3 floor
 * @pdev: platform device
 * @state: power state
 *
 * Shuts off most of docg3 circuitery to lower power consumption.
 *
 * Returns 0 if suspend succeeded, -EIO if chip refused suspend
 */
static int docg3_suspend(struct platform_device *pdev, pm_message_t state)
{
        int floor, i;
        struct mtd_info **docg3_floors, *mtd;
        struct docg3 *docg3;
        u8 ctrl, pwr_down;

        docg3_floors = platform_get_drvdata(pdev);
        for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) {
                mtd = docg3_floors[floor];
                if (!mtd)
                        continue;
                docg3 = mtd->priv;

                doc_writeb(docg3, floor, DOC_DEVICESELECT);
                ctrl = doc_register_readb(docg3, DOC_FLASHCONTROL);
                ctrl &= ~DOC_CTRL_VIOLATION & ~DOC_CTRL_CE;
                doc_writeb(docg3, ctrl, DOC_FLASHCONTROL);

                for (i = 0; i < 10; i++) {
                        usleep_range(3000, 4000);
                        pwr_down = doc_register_readb(docg3, DOC_POWERMODE);
                        if (pwr_down & DOC_POWERDOWN_READY)
                                break;
                }
                if (pwr_down & DOC_POWERDOWN_READY) {
                        doc_dbg("docg3_suspend(): floor %d powerdown ok\n",
                                floor);
                } else {
                        doc_err("docg3_suspend(): floor %d powerdown failed\n",
                                floor);
                        return -EIO;
                }
        }

        mtd = docg3_floors[0];
        docg3 = mtd->priv;
        doc_set_asic_mode(docg3, DOC_ASICMODE_POWERDOWN);
        return 0;
}

/**
 * doc_probe - Probe the IO space for a DiskOnChip G3 chip
 * @pdev: platform device
 *
 * Probes for a G3 chip at the specified IO space in the platform data
 * ressources. The floor 0 must be available.
 *
 * Returns 0 on success, -ENOMEM, -ENXIO on error
 */
static int __init docg3_probe(struct platform_device *pdev)
{
        struct device *dev = &pdev->dev;
        struct mtd_info *mtd;
        struct resource *ress;
        void __iomem *base;
        int ret, floor, found = 0;
        struct mtd_info **docg3_floors;

        ret = -ENXIO;
        ress = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        if (!ress) {
                dev_err(dev, "No I/O memory resource defined\n");
                goto noress;
        }
        base = ioremap(ress->start, DOC_IOSPACE_SIZE);

        ret = -ENOMEM;
        docg3_floors = kzalloc(sizeof(*docg3_floors) * DOC_MAX_NBFLOORS,
                               GFP_KERNEL);
        if (!docg3_floors)
                goto nomem1;
        docg3_bch = init_bch(DOC_ECC_BCH_M, DOC_ECC_BCH_T,
                             DOC_ECC_BCH_PRIMPOLY);
        if (!docg3_bch)
                goto nomem2;

        for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) {
                mtd = doc_probe_device(base, floor, dev);
                if (IS_ERR(mtd)) {
                        ret = PTR_ERR(mtd);
                        goto err_probe;
                }
                if (!mtd) {
                        if (floor == 0)
                                goto notfound;
                        else
                                continue;
                }
                docg3_floors[floor] = mtd;
                ret = mtd_device_parse_register(mtd, part_probes, NULL, NULL,
                                                0);
                if (ret)
                        goto err_probe;
                found++;
        }

        ret = doc_register_sysfs(pdev, docg3_floors);
        if (ret)
                goto err_probe;
        if (!found)
                goto notfound;

        platform_set_drvdata(pdev, docg3_floors);
        doc_dbg_register(docg3_floors[0]->priv);
        return 0;

notfound:
        ret = -ENODEV;
        dev_info(dev, "No supported DiskOnChip found\n");
err_probe:
        free_bch(docg3_bch);
        for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++)
                if (docg3_floors[floor])
                        doc_release_device(docg3_floors[floor]);
nomem2:
        kfree(docg3_floors);
nomem1:
        iounmap(base);
noress:
        return ret;
}

/**
 * docg3_release - Release the driver
 * @pdev: the platform device
 *
 * Returns 0
 */
static int __exit docg3_release(struct platform_device *pdev)
{
        struct mtd_info **docg3_floors = platform_get_drvdata(pdev);
        struct docg3 *docg3 = docg3_floors[0]->priv;
        void __iomem *base = docg3->base;
        int floor;

        doc_unregister_sysfs(pdev, docg3_floors);
        doc_dbg_unregister(docg3);
        for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++)
                if (docg3_floors[floor])
                        doc_release_device(docg3_floors[floor]);

        kfree(docg3_floors);
        free_bch(docg3_bch);
        iounmap(base);
        return 0;
}

static struct platform_driver g3_driver = {
        .driver         = {
                .name   = "docg3",
                .owner  = THIS_MODULE,
        },
        .suspend        = docg3_suspend,
        .resume         = docg3_resume,
        .remove         = __exit_p(docg3_release),
};

static int __init docg3_init(void)
{
        return platform_driver_probe(&g3_driver, docg3_probe);
}
module_init(docg3_init);


static void __exit docg3_exit(void)
{
        platform_driver_unregister(&g3_driver);
}
module_exit(docg3_exit);

MODULE_LICENSE("GPL");
MODULE_AUTHOR("Robert Jarzmik <robert.jarzmik@free.fr>");
MODULE_DESCRIPTION("MTD driver for DiskOnChip G3");